★★★ Post All Successfully Repaired Phones by Hydra Tool ★★★

[Dipendra Pathak]

Huawei FRL-L23 (Y9A 2021) both IMEI repaired successfully by Hydra Tool

1. Run Hydra MTK Module and choose Sosc.
2. Choose Brand and Module.
3. Go to "Service"->"Repair IMEI" Tab.
4. Tick "IMEI changing is illigal ……………………."
5. Choose "Huawei FlashMode" from the drop down menu.
6. Type both IMEI written as battery housing and tick both IMEI boxes
7. Click on "Repair IMEI"
8. Connect the computer to the USB data cable
9. Wait until the process is complete.

Screen Short:

BR
Dipendra Pathak

[Dipendra Pathak]

Xiaomi Redmi Note 9 (Merlin) Find Device Successfully Removed by Hydra tool

1. Run Hydra MTK Module and Sosc.
2. Choose Brand and Module.
3. Go to "Service"–>"Tool" Tab.
4. Choose "Xiaomi".
5. Click on "Find Device" from drop down menu.
6. Click "Execute" button
7. connect device to the computer with USB Data cable
8. Wait until the process is completed.

Screen Short:

BR
Dipendra Pathak

[Dipendra Pathak]

OPPO A15 (CPH 2185) Fix Dead From TP-1 by Hydra Tool

1. Run MTK Hydra tool.
2. Choose Correct Module and Brand.
3. Go to "Service" -- > Tool"
4. Choose "Oppo" tool from universal option.
5. choose "Fix dead from TP-1" from "Method / Option" drop down menu
6. Click on "Execute" and connect device with computer using USB cable.
7. Wait until the process is completed.

Screen Short:

BR
Dipendra Pathak

[Dipendra Pathak]

Oppo any MTK6765 manual boot (preloader) makes and removes FRP using by Hydra Tool

1. Run MTK tool of Hydra Dongle.
2. Choose Correct Boot File ie preloader.bin file
Note: Even you do not have boot file, you can make boot or preloader.bin
file using Hydra Tool. For this, you have to go "EXPLOIT" tab and use "(BROM) Dump preloader Flash Init."
function.
3. Choose "Auto Broom Exploit"
4. Go to "Service" -- > "Tool"
5. choose "Factory Reset Protection - FRP".
6. Choose "AUTO" from "Method / Option" of drop down menu.
7. Click on "Execute" and connect device with computer using USB cable.
8. Wait until the process is completed

Screen Short:

BR
Dipendra Pathak

[Dipendra Pathak]

Xiaomi Redmi Note 8 Pro (Begonia) successfully flashed by Hydra Tool

1. Run Hydra MTK Module,
2. Select Brand and Model
3. Tick "Auto Broom Exploit"
4. Tick "Enable UBL Loader" (Note: You can use this option if it the device does not boot properly by Hydra Tool)
5. Go to "Flash" tab
6. Choose correct file from its location and load it.
7. Untick "Enable write Preloader" if you do not write it.
8. Execute and connect the device to the computer with data cable
9. wait until the process is completed.

Screen Short:

BR
Dipendra Pathak

[Dipendra Pathak]

Oppo F3 (CPH 1609) Factory Reset or Format user data successfully done by Hydra Tool

1. Run MTK Tool and choose "Sosc"
2. Choose Brand and Module or "Auto"
3. Choose "Auto Broom Exploit"
4. Go to "Service"–> "Tool" from Universal Option
5. Choose "Factory Reset / Format user data"
6. Choose "Auto" from "Method / Option" drop down menu.
7. Connect device to computer using USB Data Cable.
8. Wait until the operation is completed

Screen Short:

BR
Dipendra Pathak

[Hydra Tool]

Xiaomi Redmi 9C (angelica) IMEI Repair by Hydra Dongle
No need Unlock Bootloader | No Need Root | No Need Auth

[Dipendra Pathak]

Vivo Y71 (1724) FRP and safe format EMMC method successfully done by Hydra Tool

1. Run Qualcomm Tool and choose "Sosc"
2. Choose Brand and Module.
3. Go to "Service"--> "Vivo"
4. Choose "Factory Reset" from drop down menu
5. Choose "Safe Format EMMC" from Flash Mode
6. Tick "Include FRP"
7. Click on "Execute"
8. Connect device to computer using USB Data Cable.
9. Wait until the operation is completed.

Screen Short:

BR
Dipendra Pathak

[Dipendra Pathak]

Redmi Note 8 (Ginkgo) Mi Account successfully removed by Hydra Tool

1. Run Hydra Qualcomm Module.
2. Choose Brand and Module.
3. Go to "Service"–>"Xiaomi" Tab.
4. Choose "Mi Account" from drop down menu.
5. Choose "Remove Mi Account" flash Mode.
6. Tick "Include FRP"
7. Disassemble the cellphone (Device)
8. Click "Execute" button
9. Connect Two Test Point using Twister or Short it.
10. connect device to the computer with USB Data cable
11. Wait until the process is completed.

Screen Short:

BR
Dipendra Pathak

[Dipendra Pathak]

Oppo A37f Factory Reset Protection -FRP successfully removed by Hydra Tool

1. Run Hydra Qualcomm Module.
2. Choose Brand and Module.
3. Go to "Service"–>"Universal" Tab.
4. Choose "Factory Reset Protection" from drop down menu.
5. Choose "Zero wipe" flash Mode.
6. Click "Execute" button
7. connect device to the computer with USB Data cable
8. Wait until the process is completed.

Screen Short:

BR
Dipendra Pathak

[Dipendra Pathak]

Huawei ATU-L22 (Y6 2018) Zero Wipe FRP successfully done by Hydra Tool

1. Run Hydra Qualcomm Module.
2. Choose Brand and Module.
3. Go to "Service"–>"Huawei" Tab.
4. Choose "Factory Reset" from drop down menu.
5. Choose "Remove FRP" flash Mode.
6. Click "Execute" button
7. connect device to the computer with USB Data cable
8. Wait until the process is completed.

Screen Short:

BR
Dipendra Pathak

[ceza031]

Xiaomi Redmi Note 8 ginkgo IMEI Repair by Hydra Dongle

Steps :

Root your device by TWRP
Enable Diag and Connect Device
or
Flash ENG Rom by EDL (Testpoint) then Repair IMEI

-----------------------------------------
IMEIRepair Function...
-----------------------------------------
Searching Diag Port....
Reading Phone info - Diag Mode
Firmware ID : MPSS.AT.4.3.1-00270-NICOBAR_GEN_PACK-1.374795.2.380402.1
Build Date : ay 7 202116:37:02Mar 04 202101:00:00nicobar.
IMEI1 :
IMEI2 :
Converting QCN to ENG QCN, Please Wait....
Anlyzze the QCN, Please Wait....

E:\Flash Files\Xiaomi\MI Roms\Redmi Note 8\Redmi_Note_8_ENG_Fix_4G.qcn
Found IMEI ONE :86xxxxxxxxxxxxx
Done...

E:\Flash Files\Xiaomi\MI Roms\Redmi Note 8\Redmi_Note_8_ENG_Fix_4G.qcn
Generationg patch imei...
Patched QCN Saved to : E:\Flash Files\Xiaomi\MI Roms\Redmi Note 8\Redmi_Note_8_ENG_Fix_4G_35xxxxxxxxxx799_patched. qcn

Writting QCN, Please Wait....
Diag Port Found ON : COM25
Writting File, Please Wait....
Sending SPC to Device....
SPC Send Success
Restoring File....
Restore File Success
Repair IMEI Success, Rebooting Device...

Elapsed Time : 00:00:49

[a_1st]

Xiaomi Redmi 9 (Lancelot) Unlock BootLoader Success

Searching for MTK Device...Found
 Port Identification :Flashmode BROM 
 FriendlyName :MediaTek USB Port (COM22)
 Device       :6&2b93e363&0&1
 SymbolicName :\??\USB#VID_0E8D&PID_0003#6&2b93e363&0&1#{a5dcbf10-6530-11d2-901f-00c04fb951ed}
 Driver Ver   :01/22/2016,3.2

Handshaking...Ok

Identifying Hardware ID.....
Reading Device hardware info..
 hw code       : 0707MT6768 [6768]
 hw subcode    : 8A00
 hw version    : CA00
 sw version    : 0000
 Target config : E7
 SBC           : 01 (True)
 SLA           : 02 (True)
 DAA           : 04 (True)
 SWJTAG        : 06 (True)
 EPP           : 00 (False)
 CERT          : 00 (False)
 MEMREAD       : 20 (True)
 MEMWRITE      : 40 (True)
 CMD_C8        : 80 (True)

Exploiting Device...
Exploit Sent..
Successfully Exploited...

Handshaking...Ok

Identifying Hardware ID.....
Reading Device hardware info..
 hw code       : 0707MT6768 [6768]
 hw subcode    : 8A00
 hw version    : CA00
 sw version    : 0000
 Target config : 00
 SBC           : 00 (False)
 SLA           : 00 (False)
 DAA           : 00 (False)
 SWJTAG        : 00 (False)
 EPP           : 00 (False)
 CERT          : 00 (False)
 MEMREAD       : 00 (False)
 MEMWRITE      : 00 (False)
 CMD_C8        : 00 (False)

MEID : 4FF873B7D5374A183BEF9F4D112132FE
Stage 1..[Size:256504]
 Sending :  Please wait.. Accepted

Identifying Protocol...
 Protocol : New
 Synchronization...SYNC
 Preloader Initialization...
 Parsing preloader_lancelot.bin
 Init : Accepted
 Executing : SYNC

Reading Device UniqueID, RAM and Flash Chip Info...
 UNIQUE ID  : A5E956D37B12E49DCF95D2605813FEB5
 ERAM Size  : 0x0000000000070000 -448 KB
 IRAM Size  : 0x0000000100000000 -4 GB
 eMMC BOOT1 : 0x0000000000400000 -4 MB
 eMMC BOOT2 : 0x0000000000400000 -4 MB
 eMMC RPMB  : 0x0000000001000000 -16 MB
 eMMC USER  : 0x0000000E8F800000 -58.242 GB
 eMMC CID   : 1501004450364441420356AF681847C5 - DP6DAB
 Executing : ACCEPTED...

Reading GPT-EMMC [0x00008000] 130 Items

Autobackup Partitions
-preloader[0x00000000]512 KB ->preloader.bin...Ok
   -> Renaming Preloader....  preloader_lancelot.bin
   Creating Scatter file... C:\Hydra Tool\\Backup\Auto\0707__073021180027\MT6768_Android_scatter.txt
-pgpt[0x00000000]32 KB ->pgpt.bin...Ok
-frp[0x05508000]1024 KB ->frp.bin...Ok
-nvdata[0x0C4A2000]64 MB ->nvdata.bin...Ok
-persist[0x104A2000]48 MB ->persist.bin...Ok
-protect1[0x164A2000]8 MB ->protect1.bin...Ok
-protect2[0x16CA2000]11.367 MB ->protect2.bin...Ok
-nvram[0x19F80000]64 MB ->nvram.bin...Ok
Done!!!
C:\Hydra Tool\\Backup\Auto\0707__073021180027
MTK Phone Loader is NOW RUNNING.

Reading Device UniqueID, RAM and Flash Chip Info...
 UNIQUE ID  : A5E956D37B12E49DCF95D2605813FEB5
 ERAM Size  : 0x0000000000070000 -448 KB
 IRAM Size  : 0x0000000100000000 -4 GB
 eMMC BOOT1 : 0x0000000000400000 -4 MB
 eMMC BOOT2 : 0x0000000000400000 -4 MB
 eMMC RPMB  : 0x0000000001000000 -16 MB
 eMMC USER  : 0x0000000E8F800000 -58.242 GB
 eMMC CID   : 1501004450364441420356AF681847C5 - DP6DAB

Reading GPT-EMMC [0x00008000] 130 Items


-------------------------------------
Operation : Unlock Bootloader
Processing...
-------------------------------
Bootloader Status...
  Bootloader : Locked
-------------------------------

Verifying status after operation...
-------------------------------
Bootloader Status...
  Bootloader : Unlocked
-------------------------------
Action Result :  Ok

Rebooting Device [Reboot To Normal]
Reboot Done!!

Elapsed Time : 00:01:48

[Dipendra Pathak]

Samsung G532 (J2 Prime) Backing Up PIT file successfully done by Hydra Tool

1. Run Hydra Main Tool.
2. Choose "Samsung" Tab.
3. Put the Device into DOWNLOAD Mode
4. Connect device to the computer using USB Data Cable.
5. Let the computer install device driver.
6. Choose "Port" that takes by Samsung Device.
7. Choose "Service" Tab
8. Choose "Partition Information Table" from drop down menu.
9. Choose “Backup PIT"
10. Tick "Auto Reboot"
11. Click on "Execute"
12. Wait until the operation is completed.

Screen Short:

BR
Dipendra Pathak

[Dipendra Pathak]

Hisilicon AGs2-L03 (MediaPad T5) FRP successfully removed by Hydra Main Tool

1. Run Hydra Main Tool.
2. Choose "Hisilicon" Tab.
3. Choose "Module"
4. UnTick "Auto Boot"
5.Choose CPU ID: Kirin 659 and Loader: Kirin 659.fb
6. Choose "Service" Tab
7. Choose "Factory Reset Protection / Account" from drop down menu.
8. Choose "Remove FRP"
9. Click on "Execute"
10. Connect the device to the compute with the help of Data Cable.
11. Wait until the operation is completed.

Screen Short:

BR
Dipendra Pathak