no network coverage [Answered] - GSM-Forum

bakht11 · 06-21-2022, 15:26

Selected model: Realme RMX3241 (Realme 8 5G)
Operation: Repair
Software version: 3.5

Host Power Off... OK
Switch virtual port to USB... OK
Connect Type-C to BOX... OK
Host Power On... OK
Connect phone to BOX in BROM mode
Wait for device... OK
Read usbhost speed... HIGH
Read Device Descriptor...
Get VID/PID...0E8D/0003
Send start cmd... OK
Get HW code from device... 0989
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6833]
Get sec config... OK [000000E5]
Active sec flags: [SBC DAA]
Advanced Bypass Security... OK
Disconnect virtual port... OK
Connect Type-C to HUB... OK
Wait for device connecting... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1504.0]
Device found at COM103 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0989
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6833]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0xC2698CA8, 0x208A8011, 0xA953ED29, 0x8CE7CB41
Get Chip ID... [MT6833]
Get SOC ID... [978EA30161BBCD9F54040A4AD24F0C80B0F46358F7FEFB7B08 D3C8E22EA9A576]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [14]
Send preloader... OK
Start preloader... OK
Check preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
UFS CID (FW VER): H9HQ15AECMBDAR (A043)
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
UFS INFO:
UFS_CID : H9HQ15AECMBDAR
UFS_FWVER : A043
BLOCK_SIZE: 0x0000001000 (4.00Kb)
UFS_LU0 : 0x0000400000 (4.00Mb)
UFS_LU1 : 0x0000400000 (4.00Mb)
UFS_LU2 : 0x1DCB000000 (119.17Gb)
RAM INFO:
INT_SRAM: 0x0000070000 (448.00Kb)
EXT_RAM : 0x0100000000 (4.00Gb)
Check USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Check A/B state... OK
Read product info... OK
Product Brand : alps
Product Manufacturer : alps
Product Model : oplus_mssi_64_cn
Product Name : sys_oplus_mssi_64_cn
Product Device : oplus_mssi_64_cn
Product Board : oppo6833
Board Platform : MT6833
Build ID : RP1A.200720.011
Build Date : Mon Mar 21 15:18:34 CST 2022
Display ID : RP1A.200720.011 release-keys
Security Patch : 2022-03-05
Version SDK : 30
Version Release : 11
Version Codename : REL
Firmware Version : 1629009929020
Read partition "nvdata"... OK
Read partition "nvram"... OK
Read NVDATA files... OK
Read NVRAM files... OK
Repairing IMEI...
IMEI 1: 35==========
IMEI 2: 35==========
Write IMEI [NVDATA]... OK
Load partiton for patching... OK
Patching CERT... already patched, skip
Unlock bootloader... OK
Write IMEI [NVRAM]... OK
Write partition "nvdata"... OK
Write partition "nvram"... OK
Repair Security done!
If your phone after repair keeps rebooting - use wipe data option.

Z3X · 06-21-2022, 15:50

Hello. Currently we dont have solution for this issue.

Z3X · 06-21-2022, 16:27

BTW, you can try to reflash phone to another firmware and try then.

bakht11 · 06-21-2022, 16:38

Quote:

Originally Posted by Z3X

BTW, you can try to reflash phone to another firmware and try then.

i flash many firmware but same problm

RMX3241export_11_A.15 a14 a13 a12 a11 a10 a8

how to remove patch?

Z3X · 06-21-2022, 17:03

Reflash and restore backups.

ali1989 · 09-28-2022, 09:00

Quote:

Originally Posted by bakht11

Selected model: Realme RMX3241 (Realme 8 5G)
Operation: Repair
Software version: 3.5

Host Power Off... OK
Switch virtual port to USB... OK
Connect Type-C to BOX... OK
Host Power On... OK
Connect phone to BOX in BROM mode
Wait for device... OK
Read usbhost speed... HIGH
Read Device Descriptor...
Get VID/PID...0E8D/0003
Send start cmd... OK
Get HW code from device... 0989
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6833]
Get sec config... OK [000000E5]
Active sec flags: [SBC DAA]
Advanced Bypass Security... OK
Disconnect virtual port... OK
Connect Type-C to HUB... OK
Wait for device connecting... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1504.0]
Device found at COM103 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0989
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6833]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0xC2698CA8, 0x208A8011, 0xA953ED29, 0x8CE7CB41
Get Chip ID... [MT6833]
Get SOC ID... [978EA30161BBCD9F54040A4AD24F0C80B0F46358F7FEFB7B08 D3C8E22EA9A576]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [14]
Send preloader... OK
Start preloader... OK
Check preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
UFS CID (FW VER): H9HQ15AECMBDAR (A043)
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
UFS INFO:
UFS_CID : H9HQ15AECMBDAR
UFS_FWVER : A043
BLOCK_SIZE: 0x0000001000 (4.00Kb)
UFS_LU0 : 0x0000400000 (4.00Mb)
UFS_LU1 : 0x0000400000 (4.00Mb)
UFS_LU2 : 0x1DCB000000 (119.17Gb)
RAM INFO:
INT_SRAM: 0x0000070000 (448.00Kb)
EXT_RAM : 0x0100000000 (4.00Gb)
Check USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Check A/B state... OK
Read product info... OK
Product Brand : alps
Product Manufacturer : alps
Product Model : oplus_mssi_64_cn
Product Name : sys_oplus_mssi_64_cn
Product Device : oplus_mssi_64_cn
Product Board : oppo6833
Board Platform : MT6833
Build ID : RP1A.200720.011
Build Date : Mon Mar 21 15:18:34 CST 2022
Display ID : RP1A.200720.011 release-keys
Security Patch : 2022-03-05
Version SDK : 30
Version Release : 11
Version Codename : REL
Firmware Version : 1629009929020
Read partition "nvdata"... OK
Read partition "nvram"... OK
Read NVDATA files... OK
Read NVRAM files... OK
Repairing IMEI...
IMEI 1: 35==========
IMEI 2: 35==========
Write IMEI [NVDATA]... OK
Load partiton for patching... OK
Patching CERT... already patched, skip
Unlock bootloader... OK
Write IMEI [NVRAM]... OK
Write partition "nvdata"... OK
Write partition "nvram"... OK
Repair Security done!
If your phone after repair keeps rebooting - use wipe data option.

Hello did you find any solition for this problem ?

06-21-2022, 15:26	#1 (permalink)
bakht11 Insane Poster Join Date: Sep 2018 Location: Pakistan Posts: 91 Member: 2863166 Status: Offline Thanks Meter: 17	no network coverage [Answered] Selected model: Realme RMX3241 (Realme 8 5G) Operation: Repair Software version: 3.5 Host Power Off... OK Switch virtual port to USB... OK Connect Type-C to BOX... OK Host Power On... OK Connect phone to BOX in BROM mode Wait for device... OK Read usbhost speed... HIGH Read Device Descriptor... Get VID/PID...0E8D/0003 Send start cmd... OK Get HW code from device... 0989 Get HW & SW version from device... OK HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00 Detect chip [MT6833] Get sec config... OK [000000E5] Active sec flags: [SBC DAA] Advanced Bypass Security... OK Disconnect virtual port... OK Connect Type-C to HUB... OK Wait for device connecting... OK Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1504.0] Device found at COM103 [BROM] Open port... OK Send start cmd... OK Get HW code from device... 0989 Get HW & SW version from device... OK HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00 Detect chip [MT6833] Library Version [2] Select platform... OK Init BROM... OK Force Charge... OK Disable WatchDog Timer... OK Reopen port for libver2... OK Get ME ID... OK ME_ID = 0xC2698CA8, 0x208A8011, 0xA953ED29, 0x8CE7CB41 Get Chip ID... [MT6833] Get SOC ID... [978EA30161BBCD9F54040A4AD24F0C80B0F46358F7FEFB7B08 D3C8E22EA9A576] Get sec config... OK [000000E0] Load DownloadAgent... OK Search DA... OK [14] Send preloader... OK Start preloader... OK Check preloader answer... OK Send bootloader... OK Start bootloader... OK Wait for answer from bootloader... OK Send SYNC signal... OK Setup device enviroment... OK Setup device parametres... OK Receive DA SYNC signal... OK Set DA parametres... OK Get device connection agent... [BROM] Get device info... OK UFS CID (FW VER): H9HQ15AECMBDAR (A043) Load EMI from phone... OK Parse EMI config... OK Init EXT RAM... OK Send 2nd DA... OK Get device info... OK UFS INFO: UFS_CID : H9HQ15AECMBDAR UFS_FWVER : A043 BLOCK_SIZE: 0x0000001000 (4.00Kb) UFS_LU0 : 0x0000400000 (4.00Mb) UFS_LU1 : 0x0000400000 (4.00Mb) UFS_LU2 : 0x1DCB000000 (119.17Gb) RAM INFO: INT_SRAM: 0x0000070000 (448.00Kb) EXT_RAM : 0x0100000000 (4.00Gb) Check USB status... USB_HIGH_SPEED Read partitions info from phone... OK Check A/B state... OK Read product info... OK Product Brand : alps Product Manufacturer : alps Product Model : oplus_mssi_64_cn Product Name : sys_oplus_mssi_64_cn Product Device : oplus_mssi_64_cn Product Board : oppo6833 Board Platform : MT6833 Build ID : RP1A.200720.011 Build Date : Mon Mar 21 15:18:34 CST 2022 Display ID : RP1A.200720.011 release-keys Security Patch : 2022-03-05 Version SDK : 30 Version Release : 11 Version Codename : REL Firmware Version : 1629009929020 Read partition "nvdata"... OK Read partition "nvram"... OK Read NVDATA files... OK Read NVRAM files... OK Repairing IMEI... IMEI 1: 35========== IMEI 2: 35========== Write IMEI [NVDATA]... OK Load partiton for patching... OK Patching CERT... already patched, skip Unlock bootloader... OK Write IMEI [NVRAM]... OK Write partition "nvdata"... OK Write partition "nvram"... OK Repair Security done! If your phone after repair keeps rebooting - use wipe data option.

06-21-2022, 15:50	#2 (permalink)
Z3X Product Supporter Join Date: Feb 2008 Location: z3x Posts: 15,903 Member: 706257 Status: Offline Thanks Meter: 5,039	Hello. Currently we dont have solution for this issue.

06-21-2022, 16:27	#3 (permalink)
Z3X Product Supporter Join Date: Feb 2008 Location: z3x Posts: 15,903 Member: 706257 Status: Offline Thanks Meter: 5,039	BTW, you can try to reflash phone to another firmware and try then.

06-21-2022, 17:03	#5 (permalink)
Z3X Product Supporter Join Date: Feb 2008 Location: z3x Posts: 15,903 Member: 706257 Status: Offline Thanks Meter: 5,039	Reflash and restore backups.