note 8 2021 repair imei done but error for patch [Answered] - GSM-Forum

rahulka · 02-04-2022, 13:33

note 8 2021 repair imei done but error for patch

Quote:

Selected model: Xiaomi M1908C3JGG (Redmi Note 8 (2021))
Operation: Patch CERT
Software version: 2.11

Host Power Off... OK
Switch virtual port to NONE... OK
Connect Type-C to HUB... OK
Host Power On... OK
Connect phone to BOX in BROM/PRELOADER Mode
Wait for device connecting... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1504.0]
Device found at COM128 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0707
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6768]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Force switch to BROM... OK
Switch virtual port to USB... OK
Connect Type-C to BOX... OK
Host Power On... OK
Wait for device... OK
Read usbhost speed... HIGH
Read Device Descriptor...
Get VID/PID...0E8D/0003
Send start cmd... OK
Get HW code from device... 0707
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6768]
Get sec config... OK [000000E7]
Active sec flags: [SBC SLA DAA]
Advanced Bypass Security... OK
Disconnect virtual port... OK
Connect Type-C to HUB... OK
Wait for device connecting... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1504.0]
Device found at COM128 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0707
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6768]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0x3608A6C6, 0x2FA24142, 0x9B38D858, 0xAAC3615C
Get Chip ID... [MT6768]
Get SOC ID... [0E9C5FA4FCC252E719ADC03AFD6E84E1D7643D99B7E973C181 BE7511CB897B08]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [25]
Send preloader... OK
Start preloader... OK
Check preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
EMMC_ID: 0x90014A68433861503E03100E62ADB727
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
EMMC INFO:
EMMC_ID : 0x90014A68433861503E03100E62ADB727
EMMC_BOOT1: 0x0000400000 (4.00Mb)
EMMC_BOOT2: 0x0000400000 (4.00Mb)
EMMC_RPMB : 0x0001000000 (16.00Mb)
EMMC_USER : 0x0E8F800000 (58.24Gb)
RAM INFO:
INT_SRAM: 0x0000070000 (448.00Kb)
EXT_RAM : 0x0100000000 (4.00Gb)
Check USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Read partition "nvdata"... OK
Read partition "nvram"... OK
Read NVDATA files... OK
Read NVRAM files... OK
Load partiton for patching... error(ERR_FND)

Z3X · 02-04-2022, 14:57

Hello. Please make dump without userdata/cache and upload it. We will recheck issue.

rahulka · 02-04-2022, 15:04

Quote:

Originally Posted by Z3X

Hello. Please make dump without userdata/cache and upload it. We will recheck issue.

phone out of access
this error i see in forums like redmi 10

rahulka · 06-18-2022, 18:43

now other error! miui 13 or 12 same

Quote:

Selected model: Xiaomi M1908C3JGG (Redmi Note 8 (2021))
Operation: Patch CERT
Software version: 3.5

Host Power Off... OK
Switch virtual port to USB... OK
Connect Type-C to BOX... OK
Host Power On... OK
Connect phone to BOX in BROM mode
Wait for device... OK
Read usbhost speed... HIGH
Read Device Descriptor...
Get VID/PID...0E8D/0003
Send start cmd... OK
Get HW code from device... 0707
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6768]
Get sec config... OK [000000E7]
Active sec flags: [SBC SLA DAA]
Advanced Bypass Security... OK
Disconnect virtual port... OK
Connect Type-C to HUB... OK
Wait for device connecting... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1504.0]
Device found at COM34 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0707
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6768]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0x77D5785E, 0x95994586, 0xDA870167, 0xFCCC99D1
Get Chip ID... [MT6768]
Get SOC ID... [700F4C4DB68C5514A84661D50210474662B083665C817DD77D 5E97D76DA0EC66]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [8]
Send preloader... OK
Start preloader... OK
Check preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
EMMC_ID: 0x90014A68433861503E03103E1BBFB743
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
EMMC INFO:
EMMC_ID : 0x90014A68433861503E03103E1BBFB743
EMMC_BOOT1: 0x0000400000 (4.00Mb)
EMMC_BOOT2: 0x0000400000 (4.00Mb)
EMMC_RPMB : 0x0001000000 (16.00Mb)
EMMC_USER : 0x0E8F800000 (58.24Gb)
RAM INFO:
INT_SRAM: 0x0000070000 (448.00Kb)
EXT_RAM : 0x0100000000 (4.00Gb)
Check USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Check A/B state... OK [B]
Read product info... OK
Product Brand : Redmi
Product Manufacturer : Xiaomi
Product Model : biloba
Product Name : biloba_global
Product Device : biloba
Product Board : biloba
Board Platform : connac1x
Build ID : SP1A.210812.016
Build Date : Mon May 23 21:26:06 CST 2022
Display ID : SP1A.210812.016
Security Patch : 2022-05-01
Version SDK : 31
Version Release : 12
Version Codename : REL
Firmware Version : V13.0.4.0.SCUMIXM
Read partition "nvdata"... OK
Read partition "nvram"... OK
Read NVDATA files... OK
Read NVRAM files... OK
Load partiton for patching... OK
Check modem patch possiblity... IMPOSSIBLE

Z3X · 06-18-2022, 18:56

Quote:

Originally Posted by rahulka

now other error! miui 13 or 12 same

Hello. As you can see from software log :

Code:

Check modem patch possiblity... IMPOSSIBLE

rahulka · 06-22-2022, 07:07

Quote:

Originally Posted by Z3X

Hello. As you can see from software log :

Code:

Check modem patch possiblity... IMPOSSIBLE

yes i see
pandora cant patch new updates!
also in redmi 9a
why you dont work for new models and new updates for xiaomi models?!

Z3X · 06-22-2022, 08:08

Quote:

Originally Posted by rahulka

yes i see
pandora cant patch new updates!
also in redmi 9a
why you dont work for new models and new updates for xiaomi models?!

Who told you that we dont work???

rahulka · 06-23-2022, 08:10

Quote:

Originally Posted by Z3X

Who told you that we dont work???

i dont know!
maybe i'm wrong.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

02-04-2022, 14:57	#2 (permalink)
Z3X Product Supporter Join Date: Feb 2008 Location: z3x Posts: 15,880 Member: 706257 Status: Offline Thanks Meter: 5,033	Hello. Please make dump without userdata/cache and upload it. We will recheck issue.