Strange problem I need help very badly.

[cole]

Hi!

I have strange problems with my new PC.<br />Beafore I buy new PC I was able to read 3210 phone.I had Asus P2B MBO with Celeron at 400MHz.<br />Now I have Asus CUSL2-C with Plll at 933MHz.<br />I can`t read 3210 phone with new PC.I mostly recive this massage:<br />Flash loader Init Error Tx=0.<br />When I try to read same 3210 on my old PC everything is OK.<br />Important thing is that I read and write 3310 without any problem on my new PC.<br />I only can`t read 3210.I try all posible combinations with f_loaders and boot bins.<br />I also try all setings from bios.I search for posible conflicts in system and etc...but without<br />good result.<br />Is somebody know how to resolve my problem.I still don`t know whay I can`t read 3210 and <br />if I reading and writing 3310 it pass without any problems.

Thanks

Cole

[mongoq]

if nothing helps just use an older pc in case the problem is speed or board related, like a 486, they cost next to nothing, you could set it up as a standalone "flasher-box" <img src="biggrin.gif" border="0"> - I did that

[cole]

Hi

Thanks for replay.I gues it will be only way to resolve my problem. <img src="mad.gif" border="0"> <img src="mad.gif" border="0"> <img src="mad.gif" border="0"> <br />I stll doing some experiment but I thing that I`m loosing my time.Is it possible that nobody else had problem like me?<br />One question.Is there any SW that will "slowing" my LPT port?I hear that there is programs that will make speed (on new generations of PC) of LPT compactibile with older BOX-s for programing IC-s.<br />Any sugestion is welcome.

Regards

Cole

[aZyWeRks]

I have a suggestion. I'm not sure if it will work but its a suggestion.

Try installing NU2001 v1.11 HASP driver coz it definitely slows down our printer port.

<br />Regards,

aCe

[cole]

Hi!

Thanks my man.Solution with HASP work,but....<br />Here is result.<br />I make download of 3210 (from 0020... till 040...)<br />When I edit file with hex editor everything was looking good.But I decide to make some test to see is that file realy good.<br />After I read phone with my new PC I didn`t power it on.So I didn`t change anything in settings of phone.Then I read it with old PC.I compare that two files (one readed with old PC and one with new) and I found 20 diference between those two files.<br />I didn`t know is that diference matter for good<br />working of phone.So I flash (with new PC) phone with fls that I read with new PC.<br />I get contact service.I was very,very disappointed.<br />Then I flash (also with new PC) phone with fls that I read with old PC.Phone work OK.Now I thing that is not resolving of my problems.<br />I didn`t get any error massage from flasher,but flasher didn`t read good.<br />So if somebody have problems like this be carefull and don`t be 100% shure that you have<br />corect backup.

I done same thing with 3310.There is no diference.Files are same.

Have anyone idea what more to to try?

Thanks

Cole

[asas]

You can insert new LPT port from other old computer. Buth you need disable port in mathermoard and set adr 378 for your new lpt. I think this will help.

[vid]

Hi Cole,

Crack voltage from PC to phone(VCC)on your 2 PC,On 3210 need 2.8v++ power to read it.

b.r.

Vid

[cole]

Hi

To Asas. I`m not shure that I know how to put LPT prot from older PC.All older PC have ISA slot controlers with LPT port intergrired inside. Unfortunately my PC have only PCI slots.Correct me if I`m wrong.

To Vid.Well I was thinking that voltage could be my problem.But when I mesure vpp at my old PC it is about 2.65 V same as on my new PC.But old read and new does not.Should I lose my time and try with external power supply???

One question.Will NU3001 cracked from spunlock work fine on my new PC or it will **** up my phones.

P.S. Today I read and unlock few 3310 without any problems with Dejans flasher.But I`m not shure it will work with 3210.So could somebody tell me (from your experience) will NU3001 work good with 3210.

Thanks for offering help.

My Best Regards

Cole

[vid]

Cole,

Uninstall NU3000 from your PC and try it again.

B.R

Vid

[quote]Originally posted by cole:<br /><strong>Hi

To Asas. I`m not shure that I know how to put LPT prot from older PC.All older PC have ISA slot controlers with LPT port intergrired inside. Unfortunately my PC have only PCI slots.Correct me if I`m wrong.

To Vid.Well I was thinking that voltage could be my problem.But when I mesure vpp at my old PC it is about 2.65 V same as on my new PC.But old read and new does not.Should I lose my time and try with external power supply???

One question.Will NU3001 cracked from spunlock work fine on my new PC or it will **** up my phones.

P.S. Today I read and unlock few 3310 without any problems with Dejans flasher.But I`m not shure it will work with 3210.So could somebody tell me (from your experience) will NU3001 work good with 3210.

Thanks for offering help.

My Best Regards

Cole</strong><hr></blockquote>