Pony program Proplem - GSM-Forum

AMTX99 · 10-24-2000, 15:36

Any one help me
I build sehcmatic for pony program.
when i use it..
i can read 24c16 fine ( eeprom of 5110)
but:-
in 24c64 & 24c128 for (6110&6150)
the program give ((device not responding))
what is the proplem?????
pleasssssssssssssssssssss help

remle · 10-24-2000, 21:07

Don't use resistor on pin7 keep it no connection.

Quote:

Originally posted by AMTX99:
Any one help me
I build sehcmatic for pony program.
when i use it..
i can read 24c16 fine ( eeprom of 5110)
but:-
in 24c64 & 24c128 for (6110&6150)
the program give ((device not responding))
what is the proplem?????
pleasssssssssssssssssssss help

slayer · 10-24-2000, 23:31

do you use external power supply(+5v)?

AMTX99 · 10-24-2000, 23:52

hi remle
i was connect the pin like this :-
5,6,7,8 of eeprom
5,6,4,8 of pony
do u mean that i dont connect pin 7 to 4

no extrnal power used

please help

remle · 10-25-2000, 00:11

Pin 4 of J3(pony) should connect to pin6(SCL) of eeprom.
Pin 5&6 should connect to pin5(SDA) of eeprom.
Pin 8 is Vcc.
Pin 1&2&3&4 is Gnd.
Pin 7 is no connection.

Quote:

Originally posted by AMTX99:
hi remle
i was connect the pin like this :-
5,6,7,8 of eeprom
5,6,4,8 of pony
do u mean that i dont connect pin 7 to 4

no extrnal power used

please help

10-24-2000, 15:36	#1 (permalink)
AMTX99 Freak Poster Join Date: Aug 2000 Age: 55 Posts: 295 Member: 1920 Status: Offline Thanks Meter: 3	Pony program Proplem Any one help me I build sehcmatic for pony program. when i use it.. i can read 24c16 fine ( eeprom of 5110) but:- in 24c64 & 24c128 for (6110&6150) the program give ((device not responding)) what is the proplem????? pleasssssssssssssssssssss help

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
reagrding ISP programming by pony prog	huzzen27	CAR Electronics	6	07-28-2009 01:48
Where to find SMD connector for pony program	FSC	Hardware Repair by brands	0	04-30-2001 19:34
T10 eprom programing with Pony	MaRiN	Old Ericsson Phones & Sony Phones	8	01-30-2001 14:12
pony prog.	AMTX99	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	0	09-25-2000 14:40

10-24-2000, 23:31	#3 (permalink)
slayer Insane Poster Join Date: Apr 2000 Location: kyiv,ukraine Posts: 71 Member: 1270 Status: Offline Thanks Meter: 0	do you use external power supply(+5v)?

10-24-2000, 23:52	#4 (permalink)
AMTX99 Freak Poster Join Date: Aug 2000 Age: 55 Posts: 295 Member: 1920 Status: Offline Thanks Meter: 3	hi remle i was connect the pin like this :- 5,6,7,8 of eeprom 5,6,4,8 of pony do u mean that i dont connect pin 7 to 4 no extrnal power used please help