Windpp registration key

[ooifk]

Hi, How to get this key? all the winddp 1.4 or windls2.4 program can't run keep on ask for this key?

ID number: 8167A538D8E8, all program shown same number and ask for key number.

1.4 Keygen soft can't generate the code with Dejan Box ID= 5001 (Standard ID from Kima), how to solve this?


Thanks

[Victor the]

Try this "52227F10DAFE3DCE2A698675"

[CarlosSantana2002]

Have the same problem; my code for 5001 can not be created

ID : 83D9BA706E1E

I wonder if someone can create a key for me

[CarlosSantana2002]

I hate doing this, but now that I post a key request, nobody seems to bother and reply with key... so... I try again

[carlito]

So... use winhex or other disk editor to change at address 7e43 the following 4 values: E5 17 5C 2E. Warning!!! make backup of original values because with this operation you change disk serial ID of your computer and other software already registered may not work. After you change the values reboot the computer in order the changes to take effect...
If all is ok and your computer still reboot :>> we all will have the same ddp ID heheh :>>> so we'll use the same key :>> which is: 8B6BFF1134BE5F873EB7B763

Ok that's all! :>> Remember you can destroy your computer is you use this method... blah blah... don;t use it if you don;t know what are you doing :>

I test the software with dejan box.. working 100% for me.

[CarlosSantana2002]

Thanx carlito it works but there is a big BUT with it.... you mixed the code up in reverse!!!

When I edited the bootsector of my harddrive and changed the previous value to the suggested E5 17 5C 2E and then rebooted... NOTHING happened WinDDP V3.0 was not registered

The right sequence is in fact: 2E 5C 17 E5

The 4 bytes are the bytes directly before the harddisk label at address 0043 0044 0045 and 0046 of the bootsector

I did not use WinHEX as suggested but "DiskEdit" from Norton Systemworks 2001 (integrated Norton Utilities) One could laso use any previous or later version as this is a DOS program and I ran it in DOS (not in DOS mode or in a DOS window)

Now... It's registered and working 100%

Thanx guys... well done

[balivo]

I´m registered the winddp 3.0 but the buttons of flashing and more ones are NOT active!!!!
Any solution?

10X

P.S. I swap the hex value for HDD ID >> I wrote: 2E 5C 17 E5 and now is registered but no active buttons????

[CarlosSantana2002]

Start WinDDP 3.0 and click on "register"
Replace the existing key in the popup window with: 8B6BFF1134BE5F873EB7B763

Click OK and then exit the program; restart PC and then all should be fine when you start WinDDP again

[balivo]

Thanks for replay!

I slove my problem!!!

Write back the REALY hex ID of HDD >> E5 17 5C 2E and then the cracked ver. winDDP 3.0 work well. Thanks!!!!

But, the custom ppm function not work on my 8210. I add Bulgarian on PPM v5.29A and v5.30C - phone work, but have unread character on bulgarian lang. all other works well ??! Any solution???

10x.

[Finn]

It requires dejan box connected in order to have enabled custom PPM button?
Also i dont remember my old HDD serila number..is there any problem?

[balivo]

Yes, require box connected to all buttons, not only for PPM !!!

PPM function work for me, but generated custom PPM are BAD