1100 contact service - GSM-Forum

tahir hussain · 02-19-2007, 21:25

I have 1100 my friend shot it on wall (angry) now some time the set is on and work ok but some time show contact service then u on off the set severel time so set is on and work.

I flash it on 6.64 and write the good pm and UI but the set in same condition
I wash it and heat it , Resold the battery connector and again flash it on 6.64 and write good pm but same problem ..............

now what I to do..........

Jintana · 02-20-2007, 05:14

try flash , upland litter see yes

vhineze2k7 · 02-20-2007, 05:42

erase flash and flash good flash file,(mcu+ppm) and write good pm......

tahir hussain · 02-21-2007, 07:05

I already try these mathod some thing else plz

is this a hardware prolem...............

Help me.............. My Friends.....

..::Sunil::.. · 02-21-2007, 07:12

Uem problem try to reheat then

1.Erase flash
2.Full flash (mcu+ppm)
3.Wright pm (Use attached pm)
4.Ul setting

Problem will solve.Yesterday I was solved this problem.

B.r.
Sunil.

sallupat · 02-21-2007, 07:13

if your problem is not yet solved by the flashing its UEM fault & its sealed UEM
salim

vhineze2k7 · 02-21-2007, 07:29

change UEM bro.....!

tahir hussain · 02-21-2007, 21:18

psunil

ok i try it and then reply here

and thanks to all helping me .......

MATRIX.REAL · 02-21-2007, 22:22

if after erase flash
flash
write good pm (1100_main)
ui setting

it is HARD PROBLEM

so try this

it can help you

tahir hussain · 02-22-2007, 20:38

I try something like that .........
1.Erase flash
2.Full flash (mcu+ppm)
3.Wright pm 1100_main.pm (Use attached pm)
4.Ul setting
but the problem is same...than I try the jumper which is given by matrix.real and the power not on and not boot on UFSx .......
I told to My hardware friend to change the flash IC he told that on change
of flash IC set is sorely dead ....I also flash on last version 8.11 mid version 6.64 old version 3.34 with given tricks but problem is remain.......
U all My Friends give me these tips thanks for that .......help me more for that
I have Twister and USFx/HWK

Thanks to all

.:KHALIFA:. · 02-23-2007, 21:43

Quote:

Originally Posted by tahir hussain

I try something like that .........
1.Erase flash
2.Full flash (mcu+ppm)
3.Wright pm 1100_main.pm (Use attached pm)
4.Ul setting
but the problem is same...than I try the jumper which is given by matrix.real and the power not on and not boot on UFSx .......
I told to My hardware friend to change the flash IC he told that on change
of flash IC set is sorely dead ....I also flash on last version 8.11 mid version 6.64 old version 3.34 with given tricks but problem is remain.......
U all My Friends give me these tips thanks for that .......help me more for that
I have Twister and USFx/HWK

Thanks to all

dear friend ... all tricks for repairing contact service with software r already done by u.... its 100% hardware problem..... u need to reball or change uem....

mike67 · 02-24-2007, 02:06

dont forget this is dropped phone ,,so software cannot heal it ,,, definitely UEM is damaged bro ,,,

Change it 100% solution ...be careful it is glued

Mike

arwanis · 02-24-2007, 02:13

yes its uem replace it and it will work fine 100%

yolem053 · 02-24-2007, 02:44

re-heat the flash ic 99% solved

vhineze2k7 · 02-24-2007, 04:00

br

try replace uem...i hope your uem is not sealed...but if it sealed you can`t replace the uem...

02-19-2007, 21:25	#1 (permalink)
tahir hussain Crazy Poster Join Date: Jul 2005 Age: 64 Posts: 58 Member: 159000 Status: Offline Thanks Meter: 13	1100 contact service I have 1100 my friend shot it on wall (angry) now some time the set is on and work ok but some time show contact service then u on off the set severel time so set is on and work. I flash it on 6.64 and write the good pm and UI but the set in same condition I wash it and heat it , Resold the battery connector and again flash it on 6.64 and write good pm but same problem .............. now what I to do..........

02-22-2007, 20:38	#10 (permalink)
tahir hussain Crazy Poster Join Date: Jul 2005 Age: 64 Posts: 58 Member: 159000 Status: Offline Thanks Meter: 13	I try something like that ......... 1.Erase flash 2.Full flash (mcu+ppm) 3.Wright pm 1100_main.pm (Use attached pm) 4.Ul setting but the problem is same...than I try the jumper which is given by matrix.real and the power not on and not boot on UFSx ....... I told to My hardware friend to change the flash IC he told that on change of flash IC set is sorely dead ....I also flash on last version 8.11 mid version 6.64 old version 3.34 with given tricks but problem is remain....... U all My Friends give me these tips thanks for that .......help me more for that I have Twister and USFx/HWK Thanks to all Last edited by tahir hussain; 02-22-2007 at 21:19.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
1100 contact service solution required	akfrm	Nokia Digital Core Technology 4 ( DCT-4 )	15	11-21-2012 15:22
1100 contact service	hyper_nokia	Nokia Digital Core Technology 4 ( DCT-4 )	2	06-16-2005 21:42
nokia 1100 contact service	elherrero	UFS2 + UFS3-Tornadoflasher	27	05-11-2005 16:21
1100 contact service	amitks_in	Griffin	4	03-24-2005 08:21
help 1100 contact service	signals	Nokia Digital Core Technology 4 ( DCT-4 )	9	03-16-2004 23:03

02-20-2007, 05:14	#2 (permalink)
Jintana Freak Poster Join Date: Nov 2006 Age: 42 Posts: 123 Member: 388374 Status: Offline Thanks Meter: 49	try flash , upland litter see yes

02-20-2007, 05:42	#3 (permalink)
vhineze2k7 Registered User Join Date: Feb 2007 Location: cuba Posts: 284 Member: 449448 Status: Offline Sonork: flush_lever Thanks Meter: 70	erase flash and flash good flash file,(mcu+ppm) and write good pm......

02-21-2007, 07:05	#4 (permalink)
tahir hussain Crazy Poster Join Date: Jul 2005 Age: 64 Posts: 58 Member: 159000 Status: Offline Thanks Meter: 13	I already try these mathod some thing else plz is this a hardware prolem............... Help me.............. My Friends.....

02-21-2007, 07:13	#6 (permalink)
sallupat No Life Poster Join Date: Apr 2005 Age: 46 Posts: 911 Member: 138982 Status: Offline Thanks Meter: 138	if your problem is not yet solved by the flashing its UEM fault & its sealed UEM salim

02-21-2007, 07:29	#7 (permalink)
vhineze2k7 Registered User Join Date: Feb 2007 Location: cuba Posts: 284 Member: 449448 Status: Offline Sonork: flush_lever Thanks Meter: 70	change UEM bro.....!

02-21-2007, 21:18	#8 (permalink)
tahir hussain Crazy Poster Join Date: Jul 2005 Age: 64 Posts: 58 Member: 159000 Status: Offline Thanks Meter: 13	psunil ok i try it and then reply here and thanks to all helping me .......

02-24-2007, 02:06	#12 (permalink)
mike67 No Life Poster Join Date: Nov 2005 Location: USA Posts: 1,163 Member: 197538 Status: Offline Thanks Meter: 97	dont forget this is dropped phone ,,so software cannot heal it ,,, definitely UEM is damaged bro ,,, Change it 100% solution ...be careful it is glued Mike

02-24-2007, 02:13	#13 (permalink)
arwanis Freak Poster Join Date: Dec 2004 Location: london uk Age: 46 Posts: 175 Member: 100185 Status: Offline Thanks Meter: 36	yes its uem replace it and it will work fine 100%

02-24-2007, 02:44	#14 (permalink)
yolem053 Freak Poster Join Date: Jan 2006 Location: Maniki Kapalong Norht Davao Posts: 336 Member: 227348 Status: Offline Sonork: yolem053 Thanks Meter: 44	re-heat the flash ic 99% solved

02-24-2007, 04:00	#15 (permalink)
vhineze2k7 Registered User Join Date: Feb 2007 Location: cuba Posts: 284 Member: 449448 Status: Offline Sonork: flush_lever Thanks Meter: 70	br try replace uem...i hope your uem is not sealed...but if it sealed you can`t replace the uem...