1600 Only blinking - GSM-Forum

pratikjh · 03-14-2007, 07:43

1600 Only blinking by switching on the phone it was water damage

Softway · 03-14-2007, 07:47

try erase + flash + write PM

..::Sunil::.. · 03-14-2007, 07:57

Quote:

Originally Posted by pratikjh

1600 Only blinking by switching on the phone it was water damage

First clean you mother bord with thinner then full flash and ulsetting.

B.r.
Sunil.

Vibin A · 03-14-2007, 13:57

clean the board and apply little heat to the board, then try to switch on.....

jalil · 03-15-2007, 10:22

Quote:

Originally Posted by pratikjh

1600 Only blinking by switching on the phone it was water damage

wash the board and just flash it it will be ok

Allunlockingsource · 03-16-2007, 05:35

plz flash mobile...............................

bhogpurmail · 03-16-2007, 05:37

flash with mcu+ppm+128CNT.............
but use jaf ,it's better for 1600

tanveershaheen · 03-16-2007, 07:11

Quote:

Originally Posted by pratikjh

1600 Only blinking by switching on the phone it was water damage

no it is flash problem

pratikjh · 03-16-2007, 08:51

by erasing error approach

yashtel · 03-16-2007, 09:25

Dont't Erase Flash The Phone With Muc Ver.3.06

yashtel · 03-16-2007, 09:26

Write Good Pm After You Flash It Might Your Network Will Drop

yashtel · 03-16-2007, 09:28

If You Have No Good Pm Than Read It From Good Handset
By Putting The Start Value " 0 " And End Value " 66 ".

vhineze2k7 · 03-16-2007, 09:32

Try Flash Using Ub Box....

pratikjh · 03-16-2007, 10:03

while erasing flash error occured

dmaetrey · 03-16-2007, 10:14

try to clean the board and let it dry for an hour....mke sure no moisture is left..then assemble......flash it...

03-14-2007, 07:43	#1 (permalink)
pratikjh Junior Member Join Date: Dec 2006 Posts: 28 Member: 412863 Status: Offline Thanks Meter: 0	1600 Only blinking 1600 Only blinking by switching on the phone it was water damage

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
1600 only nokia only	arnoldobalobao	Nokia Hardware & Hardware Repair	5	12-17-2008 15:15
MOTO V3i ONLY BLINK ONE TIME SOW ONLY MOTOROLLA	madeena	Motorola P2k	0	05-03-2008 17:42
1600 only blinking with nokia	madeena	Nokia Digital Core Technology 4 ( DCT-4 )	2	07-19-2007 17:32
E720 only blink blink	ianek	SYSOL Platform	2	07-11-2005 17:19

03-14-2007, 07:47	#2 (permalink)
Softway No Life Poster Join Date: May 2005 Posts: 2,681 Member: 143889 Status: Offline Sonork: 100.1584685 Thanks Meter: 341	try erase + flash + write PM

03-14-2007, 13:57	#4 (permalink)
Vibin A Freak Poster Join Date: Dec 2006 Location: I N D I A Posts: 125 Member: 413644 Status: Offline Thanks Meter: 10	clean the board and apply little heat to the board, then try to switch on.....

03-16-2007, 05:35	#6 (permalink)
Allunlockingsource No Life Poster Join Date: Aug 2006 Location: SPAIN-----UK Posts: 2,037 Member: 333439 Status: Offline Sonork: 100.1589101 Thanks Meter: 623	plz flash mobile...............................

03-16-2007, 05:37	#7 (permalink)
bhogpurmail Registered User Join Date: Oct 2005 Posts: 1,057 Member: 189506 Status: Offline Sonork: 100.1576871 Thanks Meter: 126	flash with mcu+ppm+128CNT............. but use jaf ,it's better for 1600

03-16-2007, 08:51	#9 (permalink)
pratikjh Junior Member Join Date: Dec 2006 Posts: 28 Member: 412863 Status: Offline Thanks Meter: 0	by erasing error approach

03-16-2007, 09:25	#10 (permalink)
yashtel No Life Poster Join Date: Aug 2005 Location: SILIGURI Age: 46 Posts: 828 Member: 170589 Status: Offline Thanks Meter: 1,848	Dont't Erase Flash The Phone With Muc Ver.3.06

03-16-2007, 09:26	#11 (permalink)
yashtel No Life Poster Join Date: Aug 2005 Location: SILIGURI Age: 46 Posts: 828 Member: 170589 Status: Offline Thanks Meter: 1,848	Write Good Pm After You Flash It Might Your Network Will Drop

03-16-2007, 09:28	#12 (permalink)
yashtel No Life Poster Join Date: Aug 2005 Location: SILIGURI Age: 46 Posts: 828 Member: 170589 Status: Offline Thanks Meter: 1,848	If You Have No Good Pm Than Read It From Good Handset By Putting The Start Value " 0 " And End Value " 66 ".

03-16-2007, 09:32	#13 (permalink)
vhineze2k7 Registered User Join Date: Feb 2007 Location: cuba Posts: 284 Member: 449448 Status: Offline Sonork: flush_lever Thanks Meter: 70	Try Flash Using Ub Box....

03-16-2007, 10:03	#14 (permalink)
pratikjh Junior Member Join Date: Dec 2006 Posts: 28 Member: 412863 Status: Offline Thanks Meter: 0	while erasing flash error occured

03-16-2007, 10:14	#15 (permalink)
dmaetrey No Life Poster Join Date: Jul 2006 Posts: 1,138 Member: 315550 Status: Offline Thanks Meter: 110	try to clean the board and let it dry for an hour....mke sure no moisture is left..then assemble......flash it...