6600 no bootup - GSM-Forum

hisham786 · 02-04-2007, 05:35

Hi,i have 6600,no bootup,white display,
In tornado

1st Boot Ok, WD2, UPP: 1081
Fl0: 0x00000000-0x007FFFFF,002088C0,St M28W640
Fl1: 0x02000000-0x027FFFFF,002088C0,St M28W640
Fl2: 0x04000000-0x047FFFFF,002088C0,St M28W640
Fl3: 0x06000000-0x067FFFFF,002088C0,St M28W640
Algorithm: w3_st_i.fia, w3_cbusb.fia, Ver: 4.52.0
Algorithm Ok, MSID: 8454C3194F90BC04366BD65D29
Decoded MSID: 3E4EBAF7-001C82C1-A9000000
Encoded FAID: F651C321-B1141CA4-A7A601F3
Area1: 0x00000000-0x0000FFFF Erased, Time: 00:00
Area2: 0x00010000-0x007FFFFF Erased, Time: 01:01
Area3: 0x04000000-0x046FFFFF Erased, Time: 00:57
Area4: 0x06000000-0x066FFFFF Erased, Time: 00:55
Area5: 0x047C0000-0x047EFFFF Erased, Time: 00:01
BT MCM (21) Image Found: 0x0002DD94
BT MCM Registering Done
MCU Flashing Completed, Time: 04:23
Area1: 0x00000000-0x0000FFFF Erased, Time: 00:00
Area2: 0x02000000-0x020DFFFF Erased, Time: 00:06
PPM Flashing Completed, Time: 00:10
Flashing Completed, Rebooting Mobile
plsa help me

Lhick · 02-04-2007, 05:44

Try Erase Flash, Flash Phone, Write PM, UI Settings.

sulai2k · 02-04-2007, 06:01

Try Erase Flash, Flash Phone, Write PM, UI Settings.

then same complaint

chage BOOT IC N380

100% ok N380 search shematics

..::Sunil::.. · 02-04-2007, 07:24

If your phone is blank display.insert a sim and check if call is going and
comming mens your displayis problem.If not tri to erase with this "fia file"
as ppm then full flash and wright a good pm.
B.r.
psunil.

.:KHALIFA:. · 02-04-2007, 18:43

i think its a hardware problem... change cpu reset ic ... all b fine... small black ic near cpu... i solved many cases... br

rockgsm · 06-12-2007, 10:40

Quote:

Originally Posted by sulai2k

Try Erase Flash, Flash Phone, Write PM, UI Settings.

then same complaint

chage BOOT IC N380

100% ok N380 search shematics

yes this is the perfect solution

acay · 06-12-2007, 10:44

if ur phone can stanby in local mode , change ic zocus!!!

rockgsm · 06-12-2007, 11:23

Quote:

Originally Posted by sulai2k

Try Erase Flash, Flash Phone, Write PM, UI Settings.

then same complaint

chage BOOT IC N380

100% ok N380 search shematics

yes this is the perfect solution

..::Mr_Fone::.. · 06-12-2007, 12:47

HI BR FIRST TRY S/W WITH NEW VER
AND 2END NOT SOLVE TRY H/W FIRST REHOT UEM AND UPP AND THEN TRY FLASH I HOP........................

..::Mr Fone::..

Dee31 · 06-12-2007, 14:49

Hi!!! If You have Griffin, Try to erase with 6600 full erase and make a full flash!!!
If still the same You must change your flash & UEM.....
Gud lucks...........

northboy · 06-12-2007, 16:35

replace rtc
then power supply

02-04-2007, 05:35	#1 (permalink)
hisham786 Freak Poster Join Date: Nov 2006 Posts: 100 Member: 396639 Status: Offline Thanks Meter: 16	6600 no bootup Hi,i have 6600,no bootup,white display, In tornado 1st Boot Ok, WD2, UPP: 1081 Fl0: 0x00000000-0x007FFFFF,002088C0,St M28W640 Fl1: 0x02000000-0x027FFFFF,002088C0,St M28W640 Fl2: 0x04000000-0x047FFFFF,002088C0,St M28W640 Fl3: 0x06000000-0x067FFFFF,002088C0,St M28W640 Algorithm: w3_st_i.fia, w3_cbusb.fia, Ver: 4.52.0 Algorithm Ok, MSID: 8454C3194F90BC04366BD65D29 Decoded MSID: 3E4EBAF7-001C82C1-A9000000 Encoded FAID: F651C321-B1141CA4-A7A601F3 Area1: 0x00000000-0x0000FFFF Erased, Time: 00:00 Area2: 0x00010000-0x007FFFFF Erased, Time: 01:01 Area3: 0x04000000-0x046FFFFF Erased, Time: 00:57 Area4: 0x06000000-0x066FFFFF Erased, Time: 00:55 Area5: 0x047C0000-0x047EFFFF Erased, Time: 00:01 BT MCM (21) Image Found: 0x0002DD94 BT MCM Registering Done MCU Flashing Completed, Time: 04:23 Area1: 0x00000000-0x0000FFFF Erased, Time: 00:00 Area2: 0x02000000-0x020DFFFF Erased, Time: 00:06 PPM Flashing Completed, Time: 00:10 Flashing Completed, Rebooting Mobile plsa help me

06-12-2007, 10:44	#7 (permalink)
acay Freak Poster Join Date: Nov 2005 Posts: 444 Member: 197916 Status: Offline Thanks Meter: 157	6600,no bootup,white display, if ur phone can stanby in local mode , change ic zocus!!!

06-12-2007, 16:35	#11 (permalink)
northboy Junior Member Join Date: May 2007 Location: UK Age: 41 Posts: 16 Member: 504636 Status: Offline Sonork: [email protected] Thanks Meter: 0	6600 boot problem replace rtc then power supply

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Help... Nokia 6600 - no signal on speaker, no signal on buzzer.	Normunds	Nokia Hardware & Hardware Repair	6	12-17-2008 08:20
6600 no open gallary and bt no work plz help	MELME	Nokia Hardware & Hardware Repair	110	07-07-2007 13:45
Nokia 6600-no backlit,no display	anandj	Nokia Hardware & Hardware Repair	1	04-08-2006 12:50
Nokia 6600 no lights on lcd and no lights on key's	floky	Nokia Hardware & Hardware Repair	2	02-17-2005 15:01
6600 no open gallary and bt no work plz help	MELME	UFS2 + UFS3-Tornadoflasher	7	12-15-2004 02:05

02-04-2007, 05:44	#2 (permalink)
Lhick No Life Poster Join Date: Aug 2006 Location: InsideOut Posts: 5,657 Member: 333359 Status: Offline Thanks Meter: 91	Try Erase Flash, Flash Phone, Write PM, UI Settings.

02-04-2007, 06:01	#3 (permalink)
sulai2k Freak Poster Join Date: Jul 2006 Posts: 420 Member: 311025 Status: Offline Sonork: 100.1607375 Thanks Meter: 171	Try Erase Flash, Flash Phone, Write PM, UI Settings. then same complaint chage BOOT IC N380 100% ok N380 search shematics

02-04-2007, 18:43	#5 (permalink)
.:KHALIFA:. No Life Poster Join Date: May 2006 Location: U wont beleive Age: 43 Posts: 1,293 Member: 275631 Status: Offline Thanks Meter: 408	i think its a hardware problem... change cpu reset ic ... all b fine... small black ic near cpu... i solved many cases... br

06-12-2007, 12:47	#9 (permalink)
..::Mr_Fone::.. No Life Poster Join Date: Oct 2006 Location: U A E Posts: 1,011 Member: 364745 Status: Offline Thanks Meter: 719	HI BR FIRST TRY S/W WITH NEW VER AND 2END NOT SOLVE TRY H/W FIRST REHOT UEM AND UPP AND THEN TRY FLASH I HOP........................ ..::Mr Fone::..

06-12-2007, 14:49	#10 (permalink)
Dee31 Freak Poster Join Date: Oct 2005 Posts: 186 Member: 192146 Status: Offline Thanks Meter: 46	Hi!!! If You have Griffin, Try to erase with 6600 full erase and make a full flash!!! If still the same You must change your flash & UEM..... Gud lucks...........