8210 "Contact Service" (fall) - GSM-Forum

thetotoman · 06-19-2003, 21:19

Hi,
I have a 8210 which is falled (felt??

) and he has the "Contact Service". How can I repair it?

Porter · 06-19-2003, 21:31

hi! Put many flux to PCB and rehot it cefuly. It`s help You!

nonu_don · 07-03-2003, 12:13

and then also try flash ur phone...

essojay · 07-03-2003, 12:17

Check the precise cause of contact service with Eeprom tool 3.0 or 3.1, then repair accordingly.

Its better to check first, dont rehot everything just like that so as not to damage perfectly working components

BR

Syed · 07-03-2003, 16:03

Yes no need to rehot anything....many many times we repair CS in dropped phones by only full flashing the phone...if software does does not help then open the hardware...

WBR
Syed

anahi · 07-09-2003, 05:27

8210

8210 Signal OK but No TX: Reflow Cobba, Reflow Hagar, replace Antenna Switch, replace PA
8210 Signal OK when first turned on then dissapears: Replace Antenna switch
8210 No signal unless IR active: Change C153
8210 Vibe and Light stay on: Replace User-Iterface IC (adjacent to power switch)
8210 "Not Charging": Remove V100
8210 No response to charger: Check F101
8210 Will charge OK but will not power ON: If there is no volts accross the power switch reflow/replace CCONT.
If there is volts accross power switch and swich is OK replace V116
8210, 8250 Locks-up, freezes: Update software, Common fault: reflow MAD (Good Luck!!)
NOTE: Many of the Nokia hardware faults are common across many models as they use the same basic chipset.
Many No-Go and Contact-Service faults can be repaired by re-loading the handset firmware and/or uploading new EEprom data.

BEN V. WAK · 08-05-2003, 10:52

IF YOUR PHONE DROP AND APPEAR CS ON THE LCD SCREEN
YOU NEED TO FLASH THE PHONE OR TRY TO PLUG IN YOUR TRAVEL CHARGER OFF AND ON THE SET..SOMETIMES IT WORKS.

soringsm · 08-18-2003, 19:43

change cobba
use nk_calc..... if cobba id=0000 it isn't ok.if cobba id#0000 is ok.
flash phone with full flash ...use nokia tool by rollis 1.8 to make authority id.

MPhoneClinic · 08-19-2003, 17:09

Quote:

Originally posted by anahi
8210

8210 No signal unless IR active: Change C153

8210 Will charge OK but will not power ON: If there is no volts accross the power switch reflow/replace CCONT.
If there is volts accross power switch and swich is OK replace V116
8210, 8250 Locks-up, freezes: Update software, Common fault: reflow MAD (Good Luck!!)
data.

Hi, i just want to clearify those faults above..
- 8210 No signal unless IR active: Change C153... it never works to me. is any one got it works by this solution??

- 8210 Will charge OK but will not power ON: If there is no volts accross the power switch reflow/replace CCONT.
If there is volts accross power switch and swich is OK replace V116..... this solution is never work... and i still trying to find the fault for this problem,.

= 8210, 8250 Locks-up, freezes: Update software, Common fault: reflow MAD (Good Luck!!)
the common fault is the MAD (cpu) dry joins.. not the software...
just replaced MAD will fixed this problem.

cheer

sheraz · 09-28-2003, 21:08

Quote:

Originally posted by thetotoman
Hi,
I have a 8210 which is falled (felt?? ) and he has the "Contact Service". How can I repair it?

hi this is sheraz make flash on 8210 it will be ok.

06-19-2003, 21:19	#1 (permalink)
thetotoman Junior Member Join Date: Apr 2003 Posts: 21 Member: 27240 Status: Offline Thanks Meter: 0	8210 "Contact Service" (fall) Hi, I have a 8210 which is falled (felt?? ) and he has the "Contact Service". How can I repair it?

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
"contact service" on 8810 - any suggestions?	dolphinsfan	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	2	09-27-2001 10:28
8250 3.12 "Contact Service"	AlphaRomeo	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	3	09-08-2001 20:35
Do you want repaire "Contact Service" by software!	hiall	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	0	08-09-2001 22:00
8250 "contact service" How to repair??	reo	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	5	08-02-2001 05:00
Is there any way to repair "Contact Service" Using Dejan Flasher	AboAli	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	3	04-19-2001 22:08

06-19-2003, 21:31	#2 (permalink)
Porter No Life Poster Join Date: Jan 2003 Location: Ukraine. Lviv Age: 43 Posts: 1,781 Member: 19633 Status: Offline Thanks Meter: 13	hi! Put many flux to PCB and rehot it cefuly. It`s help You!

07-03-2003, 12:13	#3 (permalink)
nonu_don No Life Poster Join Date: Feb 2003 Location: ..::India::.. Age: 40 Posts: 3,809 Member: 22538 Status: Offline Sonork: 100.67180 Thanks Meter: 2,252	and then also try flash ur phone...

07-03-2003, 12:17	#4 (permalink)
essojay No Life Poster Join Date: Jul 2002 Location: uk Posts: 3,601 Member: 13808 Status: Offline Thanks Meter: 163	Check the precise cause of contact service with Eeprom tool 3.0 or 3.1, then repair accordingly. Its better to check first, dont rehot everything just like that so as not to damage perfectly working components BR

07-03-2003, 16:03	#5 (permalink)
Syed No Life Poster Join Date: Jan 2003 Location: Hong Kong. Age: 47 Posts: 3,092 Member: 19979 Status: Offline Thanks Meter: 116	Yes no need to rehot anything....many many times we repair CS in dropped phones by only full flashing the phone...if software does does not help then open the hardware... WBR Syed

07-09-2003, 05:27	#6 (permalink)
anahi Junior Member Join Date: Jun 2003 Location: philipines Age: 74 Posts: 9 Member: 31611 Status: Offline Thanks Meter: 0	8210 8210 Signal OK but No TX: Reflow Cobba, Reflow Hagar, replace Antenna Switch, replace PA 8210 Signal OK when first turned on then dissapears: Replace Antenna switch 8210 No signal unless IR active: Change C153 8210 Vibe and Light stay on: Replace User-Iterface IC (adjacent to power switch) 8210 "Not Charging": Remove V100 8210 No response to charger: Check F101 8210 Will charge OK but will not power ON: If there is no volts accross the power switch reflow/replace CCONT. If there is volts accross power switch and swich is OK replace V116 8210, 8250 Locks-up, freezes: Update software, Common fault: reflow MAD (Good Luck!!) NOTE: Many of the Nokia hardware faults are common across many models as they use the same basic chipset. Many No-Go and Contact-Service faults can be repaired by re-loading the handset firmware and/or uploading new EEprom data.

08-05-2003, 10:52	#7 (permalink)
BEN V. WAK Junior Member Join Date: Jul 2003 Location: Brunei Darussalam. Age: 63 Posts: 11 Member: 35868 Status: Offline Thanks Meter: 0	IF YOUR PHONE DROP AND APPEAR CS ON THE LCD SCREEN YOU NEED TO FLASH THE PHONE OR TRY TO PLUG IN YOUR TRAVEL CHARGER OFF AND ON THE SET..SOMETIMES IT WORKS.

08-18-2003, 19:43	#8 (permalink)
soringsm Insane Poster Join Date: Jun 2002 Location: Bucharest,Romania Age: 48 Posts: 60 Member: 13363 Status: Offline Thanks Meter: 3	change cobba use nk_calc..... if cobba id=0000 it isn't ok.if cobba id#0000 is ok. flash phone with full flash ...use nokia tool by rollis 1.8 to make authority id.