urgent 1100 contact service need help - GSM-Forum

sunny_luthras · 09-24-2007, 08:44

1st Boot Ok, DCT4, UPP: 2201
Fl0: 0x01000000-0x011FFFFF,00208823,St M58MR016
Algorithm: u_st_i.fia, Ver: 4.57.0
Algorithm Ok, MSID: 84CA97B0694A3005BFC2285CFC
Decoded MSID: 3E4EBAE9-0052F0B0-A8000000
Encoded FAID: 7ED10FF0-F4F21535-1E0A7074
Area1: 0x01000000-0x0100FFFF Erased, Time: 00:00
Area2: 0x01010000-0x011EFFFF Erased, Time: 00:19
Area3: 0x011F0000-0x011FBFFF Erased, Time: 00:01
Area4: 0x013F0000-0x013FBFFF Out of Chip Bounds
Area5: 0x017F0000-0x017FBFFF Out of Chip Bounds
MCU Flashing Completed, Time: 00:08
Area1: 0x01170000-0x0117FFFF Erased, Time: 00:00
Area2: 0x01180000-0x011EFFFF Erased, Time: 00:04
PPM Flashing Completed, Time: 00:02
Flashing Completed.
Write PM Done, Time: 00:10
1st Boot Ok, DCT4, UPP: 2201
Rebooting Mobile
UI Defaults Ok, Time: 00:02
Set UI Factory Defaults Ok, Time: 00:00
Set Full Factory Defaults Ok, Time: 00:00
Set Software Upgrade Defaults Ok, Time: 00:00
Set Security Ok, Time: 00:00
IMEI: 355693-00-431022-6, ASIC: 2
SimLocks Initialized, Time: 00:03
Init Normal Mode Ok, Time: 00:10

but mobile is still in contact service need help

sunny_luthras · 09-24-2007, 09:19

some1 plz help me guys

shok9992000@yah · 09-24-2007, 09:20

Try to reflow complete board & then flash it i have solved this problem once like this

manyosa · 09-24-2007, 16:56

it is UEM faulty try to reheat RAM and UEM after flashing if still you have to change UEM.

manyosa · 09-24-2007, 17:27

it is UEM faulty try to reheat RAM and UEM after flashing if still you have to change UEM.

bpcentergtk · 09-24-2007, 18:11

have you tried with jaf try using jaf post result

WAGES · 10-17-2007, 17:34

very hard to repair some contact service
essp. 1100. help us

sopnil · 10-17-2007, 20:54

hi,
rehot um
erase flash
then write pm file
good luck

HUM · 10-17-2007, 21:13

its uem faulty....................!

as_ji · 10-17-2007, 22:36

it is UEM & flash faulty try to reheat flash and UEM....then flash... if still you have problem...change UEM.

GSMBALOCH · 04-26-2008, 17:29

I also have 1100 with device boot in normal ok but with battery its showing contact service

tarikalikhan · 04-26-2008, 20:47

In some cases It is RAM OR UEM FAULTY. but FIRST TRY TO FLASH PHONE TWICE OR THRICE, AFTER THAT REHOT THE BOARD, AND FULL ERASE, THEN FLASH HOPE IT WILL HELP YOU. BUT MOST OF THE TIME IT IS SOFTWARE PROBLEM.

09-24-2007, 08:44	#1 (permalink)
sunny_luthras Banned Join Date: Aug 2006 Posts: 195 Member: 327362 Status: Offline Thanks Meter: 45	urgent 1100 contact service need help 1st Boot Ok, DCT4, UPP: 2201 Fl0: 0x01000000-0x011FFFFF,00208823,St M58MR016 Algorithm: u_st_i.fia, Ver: 4.57.0 Algorithm Ok, MSID: 84CA97B0694A3005BFC2285CFC Decoded MSID: 3E4EBAE9-0052F0B0-A8000000 Encoded FAID: 7ED10FF0-F4F21535-1E0A7074 Area1: 0x01000000-0x0100FFFF Erased, Time: 00:00 Area2: 0x01010000-0x011EFFFF Erased, Time: 00:19 Area3: 0x011F0000-0x011FBFFF Erased, Time: 00:01 Area4: 0x013F0000-0x013FBFFF Out of Chip Bounds Area5: 0x017F0000-0x017FBFFF Out of Chip Bounds MCU Flashing Completed, Time: 00:08 Area1: 0x01170000-0x0117FFFF Erased, Time: 00:00 Area2: 0x01180000-0x011EFFFF Erased, Time: 00:04 PPM Flashing Completed, Time: 00:02 Flashing Completed. Write PM Done, Time: 00:10 1st Boot Ok, DCT4, UPP: 2201 Rebooting Mobile UI Defaults Ok, Time: 00:02 Set UI Factory Defaults Ok, Time: 00:00 Set Full Factory Defaults Ok, Time: 00:00 Set Software Upgrade Defaults Ok, Time: 00:00 Set Security Ok, Time: 00:00 IMEI: 355693-00-431022-6, ASIC: 2 SimLocks Initialized, Time: 00:03 *Init Normal Mode Ok, Time: 00:10* but mobile is still in contact service need help

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
1100 contact service. pls help	chaudry	Nokia Hardware & Hardware Repair	5	02-21-2010 06:25
nokia 1208 contact service need help urgent	shok9992000@yah	Nokia Hardware & Hardware Repair	7	02-19-2009 15:26
8250 contact service need help!!!!!!!!!!!!!!!!!!!	taihv	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	12	11-06-2004 02:02
t720 contact service need help!	hoangminhtam	Motorola P2k	0	09-14-2003 17:21
8210 5.28 Contact Service, need help to fix it!!!	Penfold	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	1	08-09-2001 21:44

09-24-2007, 09:19	#2 (permalink)
sunny_luthras Banned Join Date: Aug 2006 Posts: 195 Member: 327362 Status: Offline Thanks Meter: 45	*some1 plz help me guys*

09-24-2007, 09:20	#3 (permalink)
shok9992000@yah No Life Poster Join Date: Sep 2007 Location: chattisgarh,India Posts: 601 Member: 578941 Status: Offline Thanks Meter: 108	Try to reflow complete board & then flash it i have solved this problem once like this

09-24-2007, 16:56	#4 (permalink)
manyosa No Life Poster Join Date: May 2006 Location: Tanzania Posts: 1,562 Member: 271974 Status: Offline Thanks Meter: 97	it is UEM faulty try to reheat RAM and UEM after flashing if still you have to change UEM.

09-24-2007, 17:27	#5 (permalink)
manyosa No Life Poster Join Date: May 2006 Location: Tanzania Posts: 1,562 Member: 271974 Status: Offline Thanks Meter: 97	it is UEM faulty try to reheat RAM and UEM after flashing if still you have to change UEM.

09-24-2007, 18:11	#6 (permalink)
bpcentergtk Freak Poster Join Date: Jul 2006 Location: India(Sikkim) Posts: 252 Member: 311436 Status: Offline Thanks Meter: 38	have you tried with jaf try using jaf post result

10-17-2007, 17:34	#7 (permalink)
WAGES No Life Poster Join Date: Jul 2006 Location: ghana Posts: 1,023 Member: 320120 Status: Online Thanks Meter: 98	very hard to repair some contact service essp. 1100. help us

10-17-2007, 20:54	#8 (permalink)
sopnil No Life Poster Join Date: Jun 2007 Location: dhaka,bangladesh Posts: 790 Member: 528679 Status: Offline Thanks Meter: 268	hi, rehot um erase flash then write pm file good luck

10-17-2007, 21:13	#9 (permalink)
HUM No Life Poster Join Date: Jul 2005 Location: karachi Posts: 8,673 Member: 161728 Status: Offline Sonork: 100.1582708 Thanks Meter: 2,237	its uem faulty....................!

10-17-2007, 22:36	#10 (permalink)
as_ji Freak Poster Join Date: May 2006 Location: mumbai..9892136479 Posts: 259 Member: 275451 Status: Offline Thanks Meter: 84	it is UEM & flash faulty try to reheat flash and UEM....then flash... if still you have problem...change UEM.

04-26-2008, 17:29	#11 (permalink)
GSMBALOCH No Life Poster Join Date: May 2007 Location: Sweden Posts: 1,177 Member: 503620 Status: Offline Sonork: 1621694 Thanks Meter: 46	I also have 1100 with device boot in normal ok but with battery its showing contact service

04-26-2008, 20:47	#12 (permalink)
tarikalikhan Insane Poster Join Date: May 2007 Posts: 71 Member: 508595 Status: Offline Thanks Meter: 14	In some cases It is RAM OR UEM FAULTY. but FIRST TRY TO FLASH PHONE TWICE OR THRICE, AFTER THAT REHOT THE BOARD, AND FULL ERASE, THEN FLASH HOPE IT WILL HELP YOU. BUT MOST OF THE TIME IT IS SOFTWARE PROBLEM.