Help needed and training - GSM-Forum

greenoak · 01-27-2005, 21:33

I have just bought a UFS 3 Tornado box as I was told they are quite easy to use.

Well I have just killed a Sony T610 trying to unlock it.

Is there anyone that for a modest fee can help me restore the phone and unlock the other T610's I have.

I am near Swindon but willing to travel up to 100 miles as I cannot afford to kill any more phones

Carl
01285851611

fbendixen · 01-27-2005, 22:12

Did you use RSA button? If yes then you propably didn't wait, until soft asked for MCU file. try flashing mcu file to phone.

Best regards

MACKIE · 01-27-2005, 22:28

Quote:

Originally Posted by greenoak

I have just bought a UFS 3 Tornado box as I was told they are quite easy to use.

Well I have just killed a Sony T610 trying to unlock it.

Is there anyone that for a modest fee can help me restore the phone and unlock the other T610's I have.

I am near Swindon but willing to travel up to 100 miles as I cannot afford to kill any more phones

Carl
01285851611

If it is RSA phone then you must flash MCU.....
Before this try to boot phone with GO not RSA button....then flash MCU....

Regards
Mackie

greenoak · 01-27-2005, 22:31

Yes I did use the RSA button.

The problem is the phone will not turn on and as it has probably lost all the software files.

now says cannot find a certicated boot.

a worry on the bottom right of RTP PROGRAMME BOX IT SAYS ufs2 sarasoft then my serial number. have i been sold a dud as i have a blue ufs3 tornado box.

thanks but confused and angry CARL

greenoak · 01-27-2005, 22:38

tHE BOX JUST SAYS Please connect cable to Switched Off Mobile when using just Go and settings on manual

thanks

greenoak · 01-27-2005, 22:57

Just tried to boot phone again and when I clicked on the load button on the right , I got this message

File Ertp.ini not Exist

Not looking good

Please help

fbendixen · 01-28-2005, 09:30

When u have used RSA button, part of memory was erased.

try to select a Mcu file. and then use RSA Button. And wait until Soft says done

Best regards

greenoak · 01-28-2005, 14:39

After i have added the correct mcu file back, do i need to add the modem file afterwards or not.

Is the phone unlocked after flashing the mcu file.

When I press the unlock I get a pop up message abour new security areas found. is this normal?

So is it just just boot up with RSA button select a Mcu file. and wait until Soft says done and thats it nothing else. About 4 minutes in total with the secure boots etc

fbendixen · 01-28-2005, 14:52

No need to flash modem, if you are using the same version mcu file as Phone verion.

No you need to init locks to unlock phone.

Yes this is normal.

bibi019 · 01-31-2005, 21:07

you should make the appropriete file of mcu and gdfs
use the test point and when you connect the phone its says;Please connect cable to Switched Off Mobile then you wait for moment 5minuts
the it detecte the 1st boot and all will be ok
for more aske me privately
[email protected]

01-27-2005, 21:33	#1 (permalink)
greenoak Junior Member Join Date: Feb 2004 Age: 61 Posts: 25 Member: 53083 Status: Offline Thanks Meter: 0	Help needed and training I have just bought a UFS 3 Tornado box as I was told they are quite easy to use. Well I have just killed a Sony T610 trying to unlock it. Is there anyone that for a modest fee can help me restore the phone and unlock the other T610's I have. I am near Swindon but willing to travel up to 100 miles as I cannot afford to kill any more phones Carl 01285851611

01-28-2005, 14:39	#8 (permalink)
greenoak Junior Member Join Date: Feb 2004 Age: 61 Posts: 25 Member: 53083 Status: Offline Thanks Meter: 0	update on unlocking process After i have added the correct mcu file back, do i need to add the modem file afterwards or not. Is the phone unlocked after flashing the mcu file. When I press the unlock I get a pop up message abour new security areas found. is this normal? So is it just just boot up with RSA button select a Mcu file. and wait until Soft says done and thats it nothing else. About 4 minutes in total with the secure boots etc

Similar Threads
thread	Thread Starter	Forum	Replies	Last Post
BlackBerry 8520 unlock help needed	derk	FuriousGold	3	04-08-2010 11:37
Activa Kids' Cars and Trains Watch #SV635-001	IPMART	ipmart WebShop	0	03-07-2009 06:50
Online Training Manual Help Needed	lucascape	Hardware Repair by brands	0	09-11-2006 07:37
Blocked 7210, im a young jedi phone apprentise in need of training !!	riko_bananas	Nokia Digital Core Technology 4 ( DCT-4 )	0	06-10-2003 14:03
Need help need 768 eeprom and flash files	Ari	Old Ericsson Phones & Sony Phones	0	06-14-2002 17:24

01-27-2005, 22:12	#2 (permalink)
fbendixen Freak Poster Join Date: Jan 2004 Posts: 137 Member: 48057 Status: Offline Thanks Meter: 0	Did you use RSA button? If yes then you propably didn't wait, until soft asked for MCU file. try flashing mcu file to phone. Best regards

01-27-2005, 22:31	#4 (permalink)
greenoak Junior Member Join Date: Feb 2004 Age: 61 Posts: 25 Member: 53083 Status: Offline Thanks Meter: 0	Yes I did use the RSA button. The problem is the phone will not turn on and as it has probably lost all the software files. now says cannot find a certicated boot. a worry on the bottom right of RTP PROGRAMME BOX IT SAYS ufs2 sarasoft then my serial number. have i been sold a dud as i have a blue ufs3 tornado box. thanks but confused and angry CARL

01-27-2005, 22:38	#5 (permalink)
greenoak Junior Member Join Date: Feb 2004 Age: 61 Posts: 25 Member: 53083 Status: Offline Thanks Meter: 0	tHE BOX JUST SAYS Please connect cable to Switched Off Mobile when using just Go and settings on manual thanks

01-27-2005, 22:57	#6 (permalink)
greenoak Junior Member Join Date: Feb 2004 Age: 61 Posts: 25 Member: 53083 Status: Offline Thanks Meter: 0	Just tried to boot phone again and when I clicked on the load button on the right , I got this message File Ertp.ini not Exist Not looking good Please help

01-28-2005, 09:30	#7 (permalink)
fbendixen Freak Poster Join Date: Jan 2004 Posts: 137 Member: 48057 Status: Offline Thanks Meter: 0	When u have used RSA button, part of memory was erased. try to select a Mcu file. and then use RSA Button. And wait until Soft says done Best regards

01-28-2005, 14:52	#9 (permalink)
fbendixen Freak Poster Join Date: Jan 2004 Posts: 137 Member: 48057 Status: Offline Thanks Meter: 0	No need to flash modem, if you are using the same version mcu file as Phone verion. No you need to init locks to unlock phone. Yes this is normal.

01-31-2005, 21:07	#10 (permalink)
bibi019 No Life Poster Join Date: Jun 2004 Location: algéria Age: 47 Posts: 751 Member: 69250 Status: Offline Thanks Meter: 27	you should make the appropriete file of mcu and gdfs use the test point and when you connect the phone its says;Please connect cable to Switched Off Mobile then you wait for moment 5minuts the it detecte the 1st boot and all will be ok for more aske me privately [email protected]