R210s power off when register to network - GSM-Forum

stanimir_13 · 12-28-2004, 18:29

Hi I have one of these f***ed r210s. It was no network. I resolder it, with no result, change PA, but it start to turn off when send. I change PA again with another , but same result, I am resolve that it is antena swith. Replace it, but same. Have anybothy solution for that?????

jode · 01-05-2005, 11:18

I think you damage something while changing all that stuff. Clean board, and look carefully if there is any visual damage. If nothing, you should have a lot of luck. Try SW also (eeprom and flash) !!!

GOOD LUCK !!!

tostefo · 01-05-2005, 14:42

clean all board.....check PA ......and are you sure BAT is good?
regards

mone1 · 01-08-2005, 07:10

try to change battery if no result resolder to the battery connector and charger socket

tomsee · 01-21-2005, 11:57

Quote:

Originally Posted by stanimir_13

Hi I have one of these f***ed r210s. It was no network. I resolder it, with no result, change PA, but it start to turn off when send. I change PA again with another , but same result, I am resolve that it is antena swith. Replace it, but same. Have anybothy solution for that?????

try and change the P A

abbeydguru · 01-21-2005, 18:28

i think the battery connector is the culprit here. Do resolder the battery connector.

sergo_zmeia · 01-22-2005, 09:58

Try with PA 123BA..they are better that 122B...also try to test phone using a DC stabilized power supply...
Good luck!
sergo_zmeia

12-28-2004, 18:29	#1 (permalink)
stanimir_13 Freak Poster Join Date: Sep 2003 Posts: 259 Member: 38888 Status: Offline Thanks Meter: 52	R210s power off when register to network Hi I have one of these f***ed r210s. It was no network. I resolder it, with no result, change PA, but it start to turn off when send. I change PA again with another , but same result, I am resolve that it is antena swith. Replace it, but same. Have anybothy solution for that?????

01-22-2005, 09:58	#7 (permalink)
sergo_zmeia Freak Poster Join Date: Jun 2003 Location: Bulgaria Age: 48 Posts: 471 Member: 32284 Status: Offline Thanks Meter: 4	Hi! Try with PA 123BA..they are better that 122B...also try to test phone using a DC stabilized power supply... Good luck! sergo_zmeia

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
thread	Thread Starter	Forum	Replies	Last Post
3315 auto off when registering to network	shok9992000@yah	Nokia Hardware & Hardware Repair	11	10-15-2011 09:26
MW930 When registering to network	Abzal	Infineon C16X M51 & ARM7 M52 BASED	3	07-18-2006 13:41
T10 auto power off when IT detects network	GSM SNIPER	Old Ericsson Phones & Sony Phones	5	05-12-2005 19:43
T180 power off when register	Volodea	Motorola Old Legacy (EMMI)	0	06-19-2003 13:12
SGH-N400 turn off when getting to Network	Laser	VLSI, Conexant, Skyworks and Old Models	0	03-20-2002 19:26

01-05-2005, 11:18	#2 (permalink)
jode Freak Poster Join Date: Mar 2004 Posts: 188 Member: 57254 Status: Offline Thanks Meter: 7	I think you damage something while changing all that stuff. Clean board, and look carefully if there is any visual damage. If nothing, you should have a lot of luck. Try SW also (eeprom and flash) !!! GOOD LUCK !!!

01-05-2005, 14:42	#3 (permalink)
tostefo No Life Poster Join Date: Aug 2004 Location: Sofia Age: 43 Posts: 1,541 Member: 77941 Status: Offline Thanks Meter: 120	clean all board.....check PA ......and are you sure BAT is good? regards

01-08-2005, 07:10	#4 (permalink)
mone1 Junior Member Join Date: Jan 2005 Age: 45 Posts: 27 Member: 103485 Status: Offline Thanks Meter: 2	try to change battery if no result resolder to the battery connector and charger socket

01-21-2005, 18:28	#6 (permalink)
abbeydguru Cheater -Don't Deal with him- Join Date: Mar 2003 Location: ITALY Posts: 1,124 Member: 23994 Status: Offline Thanks Meter: 43	i think the battery connector is the culprit here. Do resolder the battery connector.