T230 RF signal processor - GSM-Forum

zepi · 07-23-2004, 00:07

Can i replace rf ic (10111013c) with rf ic from T39/T68 (1011101/2c)

TNX

Unggul · 07-23-2004, 20:06

no, you can't
don't do it that will destroy your phone

bestman · 07-25-2004, 02:07

you can replace rf IC.using rework - station.
this application tool is a heater , you must use recommended temp.

bestman.

**Brka** · 07-26-2004, 01:52

as far as I know ...
all phones after t20, t29
use the same RF IC ..
even T610 ... on some u can find
Infineon RF IC ... but thats because
infineon bought SE IC factory ....

all new rf ic's fits .... in : t610, t39/t65, t3x0, t200, t230 ...

only C62 RF IC is different

b.r.
ALexandar.

p.s. shta ima novo kolege ?

zepi · 07-26-2004, 09:48

Hm....
I try with one from T68i (1011101/2c) and no network, after that with Infineon from T610 and also no network. IC's are good, when i put it back to T68 - network is full, so i think that T230 must use only 10111013 rf processor.

ps. C62 use Infineon, same as in T610

**Brka** · 07-30-2004, 17:08

hmmm
its possible

but, have you tried with RF from another T230 ?
maybe the problem is not in the RF ic ...

i had such a cases ... but on t68 and t610 phones ...
putting another, working RF IC did not solve no network ...

consider that possibility

b.r.
ALexandar.

p.s. tnx for info about c62. see ya m8.

misel · 09-28-2004, 15:45

and I am in face of new problem with T630,phone connect to network fine ,can make a good call,also signal level is good,after aprox.10 minutes when phone is in deep standby,phone not accept calls ,out of reach,and signal become low,1-2,sometimes 4 bar,but newer 5,,then i start to pressing buttons,phone go out from standby,lights come up,after 1 minutes everything is in good condition,accept calls,can make calls everything work perfect,, I flashed with Fighter R6C005,ARM&AVR, reflow diplexer,flash,AVR & ARM IC,pover IC, RF-IC not direct,only arround with low temp,after whole work day I am at start position just where I was few hours before,,

any good Idea is better then nothing

misel · 09-28-2004, 20:11

today afternoon I change 3014 power managment IC ,also change ,RxTx switch,then change 13 Mhz and 32 Khz cristal ,,but phone not work fine in standby ,no network appear after 10 minutes,,after touching some buttons in 1 minute network comes again ,and phone work good as long as I play with buttons ,,if I live phone in standby after 10 min no network.....

zepi · 09-28-2004, 22:09

Did You reflow cpu and flash ic?

misel · 09-29-2004, 20:44

already yes ,,naravno i posle dva dana sam na pocetku ,sve pod mikroskopom u detalje pregledao ,odmastio celu plocu ,everything look perfect ,ali zajebava..

**Brka** · 10-01-2004, 02:27

misa

change the phucking RF IC .... thats it
similiar case like on t28 and older stupid ericssons
also change diplexer ...

that must work

b.r.
alexandar.

07-23-2004, 00:07	#1 (permalink)
zepi Freak Poster Join Date: Nov 2003 Location: Belgrade Serbia Age: 53 Posts: 154 Member: 44417 Status: Offline Thanks Meter: 1	T230 RF signal processor Can i replace rf ic (10111013c) with rf ic from T39/T68 (1011101/2c) TNX

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
RF signal tester equipment, anyone can help?	agungch	Hardware Equipments for GSM	1	06-13-2007 10:08
RF SIGNAL VALUES for P910i	ahmed	Cruiser Suite	9	12-07-2006 18:10
3510i no signal! processor already reheated!	mikelim	Nokia Hardware & Hardware Repair	2	12-02-2005 02:08
Need help on see RF signal on Spectrum Analiser	sed_alex	Hardware Repair by brands	1	06-18-2003 20:31
Looking for signal processors Ericsson	NBG	Sony Ericsson Hardware Repair	0	10-12-2002 14:09

07-23-2004, 20:06	#2 (permalink)
Unggul No Life Poster Join Date: Jul 2004 Location: Bandung - West Java, Indonesia Age: 43 Posts: 501 Member: 71273 Status: Offline Thanks Meter: 14	no, you can't don't do it that will destroy your phone

07-25-2004, 02:07	#3 (permalink)
bestman No Life Poster Join Date: Apr 2004 Age: 49 Posts: 1,271 Member: 61294 Status: Offline Thanks Meter: 49	you can replace rf IC.using rework - station. this application tool is a heater , you must use recommended temp. bestman.

07-26-2004, 01:52	#4 (permalink)
Brka Moderator Join Date: Jun 1999 Location: Serbia Age: 48 Posts: 8,206 Member: 163 Status: Offline Thanks Meter: 7,784	as far as I know ... all phones after t20, t29 use the same RF IC .. even T610 ... on some u can find Infineon RF IC ... but thats because infineon bought SE IC factory .... all new rf ic's fits .... in : t610, t39/t65, t3x0, t200, t230 ... only C62 RF IC is different b.r. ALexandar. p.s. shta ima novo kolege ?

07-26-2004, 09:48	#5 (permalink)
zepi Freak Poster Join Date: Nov 2003 Location: Belgrade Serbia Age: 53 Posts: 154 Member: 44417 Status: Offline Thanks Meter: 1	Hm.... I try with one from T68i (1011101/2c) and no network, after that with Infineon from T610 and also no network. IC's are good, when i put it back to T68 - network is full, so i think that T230 must use only 10111013 rf processor. ps. C62 use Infineon, same as in T610

07-30-2004, 17:08	#6 (permalink)
Brka Moderator Join Date: Jun 1999 Location: Serbia Age: 48 Posts: 8,206 Member: 163 Status: Offline Thanks Meter: 7,784	hmmm its possible but, have you tried with RF from another T230 ? maybe the problem is not in the RF ic ... i had such a cases ... but on t68 and t610 phones ... putting another, working RF IC did not solve no network ... consider that possibility b.r. ALexandar. p.s. tnx for info about c62. see ya m8.

09-28-2004, 15:45	#7 (permalink)
misel No Life Poster Join Date: Apr 2000 Location: near you Age: 60 Posts: 560 Member: 1196 Status: Offline Thanks Meter: 6	and I am in face of new problem with T630,phone connect to network fine ,can make a good call,also signal level is good,after aprox.10 minutes when phone is in deep standby,phone not accept calls ,out of reach,and signal become low,1-2,sometimes 4 bar,but newer 5,,then i start to pressing buttons,phone go out from standby,lights come up,after 1 minutes everything is in good condition,accept calls,can make calls everything work perfect,, I flashed with Fighter R6C005,ARM&AVR, reflow diplexer,flash,AVR & ARM IC,pover IC, RF-IC not direct,only arround with low temp,after whole work day I am at start position just where I was few hours before,, any good Idea is better then nothing

09-28-2004, 20:11	#8 (permalink)
misel No Life Poster Join Date: Apr 2000 Location: near you Age: 60 Posts: 560 Member: 1196 Status: Offline Thanks Meter: 6	today afternoon I change 3014 power managment IC ,also change ,RxTx switch,then change 13 Mhz and 32 Khz cristal ,,but phone not work fine in standby ,no network appear after 10 minutes,,after touching some buttons in 1 minute network comes again ,and phone work good as long as I play with buttons ,,if I live phone in standby after 10 min no network.....

09-28-2004, 22:09	#9 (permalink)
zepi Freak Poster Join Date: Nov 2003 Location: Belgrade Serbia Age: 53 Posts: 154 Member: 44417 Status: Offline Thanks Meter: 1	Did You reflow cpu and flash ic?

09-29-2004, 20:44	#10 (permalink)
misel No Life Poster Join Date: Apr 2000 Location: near you Age: 60 Posts: 560 Member: 1196 Status: Offline Thanks Meter: 6	already yes ,,naravno i posle dva dana sam na pocetku ,sve pod mikroskopom u detalje pregledao ,odmastio celu plocu ,everything look perfect ,ali zajebava..

10-01-2004, 02:27	#11 (permalink)
Brka Moderator Join Date: Jun 1999 Location: Serbia Age: 48 Posts: 8,206 Member: 163 Status: Offline Thanks Meter: 7,784	misa change the phucking RF IC .... thats it similiar case like on t28 and older stupid ericssons also change diplexer ... that must work b.r. alexandar.