help to make my usb cable to unlock j100i - GSM-Forum

chris2007 · 11-28-2008, 23:48

i used "S_E J100DMTool" to unlock my j100i can't unlock by smart-clip

a usb SE001 SE k750i cable need to make for unlock my j100i

the cable with 4 wires red,green,white and black wire ...

my question what colour should i solder for the RX/TX and GND?????

GSM_Support · 11-29-2008, 10:13

Quote:

Originally Posted by chris2007

i used "S_E J100DMTool" to unlock my j100i can't unlock by smart-clip

What do you mean, you can't unlock it with Smart-Clip? This model is supported by "one button" operation.

Power off the phone.
Connect the Clip to the phone using RJ45 cable (see pinout schematic below).
Press UNLOCK button.
Press Power button on the phone within 5 seconds after you press UNLOCK button on the Clip. RX/TX leds will blink.
E/G led will glow green on success.*

* After successful unlock (green led on) phones with inserted sim card may ask for PCK or NCK code. Enter 00000000 ("zero" 8 times).

And here is the required cable pinout.

Best Regards
GSMServer team

chris2007 · 11-30-2008, 23:36

1- Phone ask for "Phone Lock code"
SW Ver : R1C004
dsfRev:R2A CXC1250386_lp_HONGKONG_r1c004

Power off the phone.
Connect the Clip to the phone using RJ45 cable i Press UNLOCK button.
Press Power button on the phone within 5 seconds after i press UNLOCK button on the Clip. RX/TX leds is blink.
E/G led glow red.

The cable is ok!

Phone can't unlock

2-Phone ask for "Subsidy pwd:"
SW Ver: R10009
dsfRev:R2C CXC1250396_lp_EU2_R10009

Power off the phone.
Connect the Clip to the phone using RJ45 cable i Press UNLOCK button.
Press Power button on the phone within 5 seconds after i press UNLOCK button on the Clip. RX/TX leds is blink.
E/G led glow green.

by using the same cable but insert sim still ask for the "Subsidy pwd:" enter "0000" can't be unlock

Mr.Tinkertrain · 12-01-2008, 10:14

@ chris2007,

Did E/G led glow green after the unlock procedure?
Was the battery fully charged?

Best Regards
Smart-clip team
www.smart-clip.com
www.scoutdongle.com
www.GsmServer.com
www.boot-loader.com
www.smart-unlocker.com

chris2007 · 12-01-2008, 22:13

yes the battery fully charged

Mr.Tinkertrain · 12-02-2008, 09:10

@ chris2007,

What light indicator glows at the end of the unlock procedure?

Best Regards
Smart-clip team
www.smart-clip.com
www.scoutdongle.com
www.GsmServer.com
www.boot-loader.com
www.smart-unlocker.com

chris2007 · 12-05-2008, 00:03

i have two phone to unlock one phone has been green light after unlock and the other phone was in red light cable good battery fully charged

xerraco · 12-05-2008, 11:45

Just repeat the Procedure Mate.

11-28-2008, 23:48	#1 (permalink)
chris2007 No Life Poster Join Date: Feb 2007 Posts: 3,197 Member: 453916 Status: Offline Sonork: 100.1620840 Thanks Meter: 246	help to make my usb cable to unlock j100i i used "S_E J100DMTool" to unlock my j100i can't unlock by smart-clip a usb SE001 SE k750i cable need to make for unlock my j100i the cable with 4 wires red,green,white and black wire ... my question what colour should i solder for the RX/TX and GND?????

11-30-2008, 23:36	#3 (permalink)
chris2007 No Life Poster Join Date: Feb 2007 Posts: 3,197 Member: 453916 Status: Offline Sonork: 100.1620840 Thanks Meter: 246	1- Phone ask for "Phone Lock code" SW Ver : R1C004 dsfRev:R2A CXC1250386_lp_HONGKONG_r1c004 Power off the phone. Connect the Clip to the phone using RJ45 cable i Press UNLOCK button. Press Power button on the phone within 5 seconds after i press UNLOCK button on the Clip. RX/TX leds is blink. E/G led glow red. The cable is ok! Phone can't unlock 2-Phone ask for "Subsidy pwd:" SW Ver: R10009 dsfRev:R2C CXC1250396_lp_EU2_R10009 Power off the phone. Connect the Clip to the phone using RJ45 cable i Press UNLOCK button. Press Power button on the phone within 5 seconds after i press UNLOCK button on the Clip. RX/TX leds is blink. E/G led glow green. by using the same cable but insert sim still ask for the "Subsidy pwd:" enter "0000" can't be unlock

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
How to make an USB cable to flash LG3 phones with Vygis?	E&D	LG	1	02-22-2006 12:03
How to make an usb cable to flsh c62	E&D	NON Siemens Brand (ODM Phones)	8	02-17-2006 13:43
How to make a usb-cable for 902sh?	schupa	Sharp	4	06-12-2005 17:07
Help to make da data cable to change for unlocking an ME45	octavian	Siemens Hardware Repair Area	1	01-29-2004 18:44
Any one know how to make 7650 USB cable	Beginner	WD2 & APE (Symbian Phones)	0	04-09-2003 03:29

12-01-2008, 10:14	#4 (permalink)
Mr.Tinkertrain No Life Poster Join Date: Feb 2006 Posts: 11,638 Member: 229997 Status: Offline Thanks Meter: 636	@ chris2007, Did E/G led glow green after the unlock procedure? Was the battery fully charged? Best Regards Smart-clip team www.smart-clip.com www.scoutdongle.com www.GsmServer.com www.boot-loader.com www.smart-unlocker.com

12-01-2008, 22:13	#5 (permalink)
chris2007 No Life Poster Join Date: Feb 2007 Posts: 3,197 Member: 453916 Status: Offline Sonork: 100.1620840 Thanks Meter: 246	yes the battery fully charged

12-02-2008, 09:10	#6 (permalink)
Mr.Tinkertrain No Life Poster Join Date: Feb 2006 Posts: 11,638 Member: 229997 Status: Offline Thanks Meter: 636	@ chris2007, What light indicator glows at the end of the unlock procedure? Best Regards Smart-clip team www.smart-clip.com www.scoutdongle.com www.GsmServer.com www.boot-loader.com www.smart-unlocker.com

12-05-2008, 00:03	#7 (permalink)
chris2007 No Life Poster Join Date: Feb 2007 Posts: 3,197 Member: 453916 Status: Offline Sonork: 100.1620840 Thanks Meter: 246	i have two phone to unlock one phone has been green light after unlock and the other phone was in red light cable good battery fully charged

12-05-2008, 11:45	#8 (permalink)
xerraco No Life Poster Join Date: Nov 2008 Location: RVIII Posts: 11,696 Member: 890926 Status: Offline Thanks Meter: 2,053	Just repeat the Procedure Mate.