how to unlock v3xx with test point????

[abdelhak_gsm]

Please friends I have cable for test point v3xx but the problem I did not know how to connect because it contains four wire
1: yellow
2nd: Green
3 rd: red
4th: Black
And a sheet rj45
For black and red I know it's replace baterie
But yellow and green I do not know which I use
Please the procedure deblocage this phone with this cable
Thank you in advance

[TICTAC_M]

if you buy cable in ipmart green is tp A and it is the you used for v3xx. tp b is only for unlock w510 in any case. the procedure for unlock phone you can read in smart-clip.com.

[X-TRA]

Originally Posted by abdelhak_gsm

Please friends I have cable for test point v3xx but the problem I did not know how to connect because it contains four wire
1: yellow
2nd: Green
3 rd: red
4th: Black
And a sheet rj45
For black and red I know it's replace baterie
But yellow and green I do not know which I use
Please the procedure deblocage this phone with this cable
Thank you in advance

hi there
1st use try to search



Prepare Smart TestPoint (Argon: K3, V1100, V3re (V3_06), V3xx, V3xx Cingular (North America), V6maxx, Foma M702iG. LTE2_ROM4: L9, L72, W510)

1. Connect powered ON handset to PC via Smart-Clip (phone > USB cable > Smart-Clip > LPT cable > PC).
2. Connect S-Card to PC USB port.
3. Connect power supply to Smart-Clip and power on the handset.
4. Launch SmartMoto.
5. Choose "Smart-Clip USB port" in phone connection window.
6. Press "Search". The software should perform the following steps:
   • SmartMoto detects S-Card;
   • SmartMoto detects Smart-Clip;
   • SmartMoto detects the handset and reads all phone information.
7. Log to bookmark “Prepare”
8. Select an appropriate model from the list.
9. Mark “Unlock automatically” and press “Prepare Smart TestPoint” button.
10. Prepare operation is in progress. The handset gets reloaded, backup of firmware is saved.
11. SmartMoto pops up the message requiring Smart TestPoint cable to be connected. Please perform the following:
    • Disconnect the handset and dismantle it
    • Please ensure that LCD is disconnected from the board!!!
    • Connect Smart TestPoint cable to the port RJ45 on Smart-Clip
    • Connect data cable to the phone
    • Connect battery hook to the positive (+) battery contact on PCB
    • Connect needle A to the primary TestPoint A and hold it until the software informs that it can be disconnected
    • Press OK in SmartMoto. The handset should be detected with boot version 0.00.
12. Unlock procedure continues.
13. Disconnect TP needle when SmartMoto informs to do so.
14. If the option "Unlock automatically" was marked – the handset becomes unlocked. If the option was not selected then the handset can be served for Flash, Repair PDS, Unlock or Backup purposes.

NOTE. W510 and Foma M702iG schematic contains 2 TestPoints, A (primary) and B (secondary). In case if unlock fails using single TestPoint A, please perform the process, using both TestPoints simultaneously (connect needle A to TP A and needle B to TP B).

• Yellow - TestPoint A (Primary)
• Black - TestPoint B (Secondary)
• Red - Battery Hook

Please follow this order strictly. Do not use power from the battery. Use battery hook and ensure that it’s connected to the appropriate (“+” Positive) contact.




with best regards
ahmad

[Mr.Tinkertrain]

@ abdelhak_gsm,

Check this link, please.



Best Regards
Smart-clip team
www.smart-clip.com
www.scoutdongle.com
www.GsmServer.com
www.boot-loader.com
www.smart-unlocker.com

[abdelhak_gsm]

thkx friens problem phone unlocked succefly





abdelhak_gsm

[sairat]

THIS ERROR OCCURS DURING PREPARE SMART TP

SmartMoto 2.42
S-Card: ******** Smart-Clip dongle, v 1.50, assigned Smart-Clip: 741803*** Europe, initializing... OK
Clip serial: 741******, 0version: 3.25, initializing... OK
Searching for phone... found Motorola Phone (RAZRV3xx), getting test interface... OK
Reading <Model>... test cmd error 06
Searching for phone... found Motorola Phone (RAZRV3xx), getting test interface... OK
Model RAZRV3xx
Firmware R26111LD_U_96.80.51R
Switching to flash mode... OK [S Flash Argon]
Reading phone boot version... 3.02
Cannot create backup file C:\Program Files\GsmServer\SmartMoto\temporary backup\bkp_11A3111144B6E450.bk_
Backup failed
Searching for phone... found S Flash Argon, getting test interface... interface not found
Switching to flash mode... OK
Searching for phone... found Motorola Phone (RAZRV3xx), getting test interface... OK
Model RAZRV3xx
Firmware R26111LD_U_96.80.51R
Switching to flash mode... OK [S Flash Argon]
Reading phone boot version... 3.02
Cannot create backup file C:\Program Files\GsmServer\SmartMoto\temporary backup\bkp_11A3111144B6E450.bk_
Backup failed

[TICTAC_M]

review power for smart clip. maybe do not give power necesary for it operation. or phone have problem, smart clip do not have read information of phone.

Reading <Model>... test cmd error 06

[sairat]

Originally Posted by TICTAC_M

review power for smart clip. maybe do not give power necesary for it operation. or phone have problem, smart clip do not have read information of phone.

Reading <Model>... test cmd error 06

BRO BUT NEXT TIME ITS READING PHONE BUT NOT MAKING ITS BACKUP

Searching for phone... found S Flash Argon, getting test interface... interface not found
Switching to flash mode... OK
Searching for phone... found Motorola Phone (RAZRV3xx), getting test interface... OK
Model RAZRV3xx
Firmware R26111LD_U_96.80.51R
Switching to flash mode... OK [S Flash Argon]
Reading phone boot version... 3.02
Cannot create backup file C:\Program Files\GsmServer\SmartMoto\temporary backup\bkp_11A3111144B6E450.bk_
Backup failed

[TICTAC_M]

but only you have error in read phone. and do you sure that batery is full?

Searching for phone... found Motorola Phone (RAZRV3xx), getting test interface... OK
Reading <Model>... test cmd error 06
Searching for phone... found Motorola Phone (RAZRV3xx), getting test interface... OK
Model RAZRV3xx
Firmware R26111LD_U_96.80.51R
Switching to flash mode... OK [S Flash Argon]
Reading phone boot version... 3.02
Cannot create backup file C:\Program Files\GsmServer\SmartMoto\temporary backup\bkp_11A3111144B6E450.bk_
Backup failed
Searching for phone... found S Flash Argon, getting test interface... interface not found--phone in test mode
Switching to flash mode... OK
Searching for phone... found Motorola Phone (RAZRV3xx), getting test interface... OK
Model RAZRV3xx
Firmware R26111LD_U_96.80.51R
Switching to flash mode... OK [S Flash Argon]
Reading phone boot version... 3.02
Cannot create backup file C:\Program Files\GsmServer\SmartMoto\temporary backup\bkp_11A3111144B6E450.bk_
Backup failed

[rushwhq]

Damn,

Can u Sc Team do it better, we need a EASY solution. That why we bought SClip guys.
U started launching tp, magictestpoint, and now this shi.ti. My go.d.

[NUNO_GSM]

* Yellow - TestPoint A (Primary)
* Black - TestPoint B (Secondary)
* Red - Battery Hook

[Lhick]

Originally Posted by rushwhq

Damn,

Can u Sc Team do it better, we need a EASY solution. That why we bought SClip guys.
U started launching tp, magictestpoint, and now this shi.ti. My go.d.

Users are to Blame if phones are F**K on unlock, There are Lots of Successful Unlock Post...Unlocking need not just knowledge but Experience & Skills.

[Mr.Tinkertrain]

@ sairat,

Fully charge the battery and try once again.
Before performing any operation please double check the manual.
Also, please tell us what cable you are using?
Where have you purchased it?



Best Regards
Smart-clip team
www.smart-clip.com
www.scoutdongle.com
www.GsmServer.com
www.boot-loader.com
www.smart-unlocker.com

[Dengel]

i think that this is GPG industries cable...

[kwamena]

Originally Posted by rushwhq

Damn,

Can u Sc Team do it better, we need a EASY solution. That why we bought SClip guys.
U started launching tp, magictestpoint, and now this shi.ti. My go.d.

whats are you talking about? this is the way to the future you must be even happy we are able to unlock these phones now. take a look at BB5 is it easy? and now sony ericsson has moved from DB2020 to A2 do you think its easy to get the solution in some years? even if we get the solution it will be more than this 10 times. to all the sunday unlockers who **** up prices you better find another job because the future is clear for professionals.

THANK YOU SC TEAM FOR SUCH A NICE UPDATE.