Z3 Unlock using Testpoint Adaptor URGENT - GSM-Forum

MeeM · 02-06-2008, 10:53

URGENT!

I have a Z3 to unlock for a customer. I've removed the back cover. When I bought my Smart-Clip, I bought the Testpoint adaptors set and I got hte Z3 testpoint adaptor with me. It's this one:

(http://gsmserver.com/cables/cable_details.php?id=8594)

Where do I put this adaptor to do the TP? A photo would be good

And then do I go into smartmoto, select unlock, and unlock via tp?

Help!!

Mr.Tinkertrain · 02-06-2008, 10:59

@ MeeM,

in case if your phone has boot version A.C.0 or A.C.3. it can be unlocked via Prepare cycle. Check this link for more detailed information.

Best Regards
Smart-clip team
www.smart-clip.com
www.scoutdongle.com
www.GsmServer.com
www.boot-loader.com
www.smart-unlocker.com

MeeM · 02-06-2008, 11:07

Ok, I'm downloading the new SmartMoto because the old version said to update. Then I will check the phone information in SmartMoto to see if the boot version is AC0 or AC3.

If it is not, how do I do the TP? I have the testpoint adaptors but I can't find any instructions on how to use them or where to put them, and no one else seems to be using them...?

Lhick · 02-06-2008, 11:17

Quote:

If it is not, how do I do the TP?

If it is not supported via Prepare Procedure, You just Short the said TP point to Gnd(ground)

MeeM · 02-06-2008, 11:36

Ok ... there's another problem now. My smart-clip box is connected (with power supply and parallel connection to PC), and the red power light is on and the yellow/green E/G light is on. When i click 'connect' in smartmoto, the lights on the box turn off, and then smart-moto says smart-clip not found!. The lights on the box come back on after a few seconds. Why?!

I have updated my smart dongle and the smart-clip, and the update software finds the dongle and clip without a problem. Why doesn't smartmoto find my clip? It finds my dongle, just not my clip.

I have polling disabled on the parallel port.

I'm using SmartMoto 3.07 European.

Mr.Tinkertrain · 02-06-2008, 11:46

@ MeeM,

Please make sure that:
1. Firewall on your computer (or your LAN) is configured properly or disabled
2. LPT port settings are set to EPP in BIOS
3. Your LPT cable works properly
4. You use a stable power supply with your clip (use power adapter 12V 750mA)
5. If you are using WinXP, log in as Administrator or any other account with administrative rights

To run a new SmartMoto under WinXP also to update a Smart-Clip please
launch the SmartMoto, open Smart-Clip bookmark & tick the option "Disable OS parallel port polling (requires reboot)".
After that restart you PC.
Also set LPT options in SmartMoto to compatibility

Best Regards
Smart-clip team
www.smart-clip.com
www.scoutdongle.com
www.GsmServer.com
www.boot-loader.com
www.smart-unlocker.com

cbz_4383 · 02-06-2008, 12:01

@MeeM
select LPT1 at smart clip option in smart moto .
its not auto selected you have to do this 1 time after its no need.

MeeM · 02-06-2008, 12:13

ok ... smartmoto found my clip now.

I would like to use my testpoint adaptor with the button on it, apparently it makes things easier for tp, but no one can tell me where to put it and what else to do!! anyone?

phone boot version is ac3 so i can do the prepare, and it will unlock automatically ... so no TP

hopefully!

I'll let you know how it goes.

MeeM · 02-06-2008, 12:23

IT WORKED!!
thanks a lot guys!

MeeM · 02-06-2008, 13:50

I guess my next question would be: does anyone have the Motorola testpoint adapters? If so, how do you know where to put them on the phone? And what procedure do you need to follow to unlock the phone? (ie when to put it on the phone, when to press the red button, etc.)

CONCORDIA GSM · 02-06-2008, 18:49

Quote:

Originally Posted by MeeM

I guess my next question would be: does anyone have the Motorola testpoint adapters? If so, how do you know where to put them on the phone? And what procedure do you need to follow to unlock the phone? (ie when to put it on the phone, when to press the red button, etc.)

please folow the steps carefully
attach tp with lcd conector on main board
attach cable
remain pressing button on tp insert battery
search with smartmoto
after reading information release tp button
now you can unlock or flash.

MeeM · 02-07-2008, 05:26

Ahh ok .. so you disassemble the phone, remove the LCD screen and disconnect it from the board, and put the Testpoint Adapter on the LCD connector on the board. That's what I needed to know.

Thanks for the instructions. Will use them when the next V3 or Z3 comes in

02-06-2008, 10:53	#1 (permalink)
MeeM Insane Poster Join Date: Dec 2007 Posts: 97 Member: 655243 Status: Offline Thanks Meter: 0	Z3 Unlock using Testpoint Adaptor URGENT URGENT! I have a Z3 to unlock for a customer. I've removed the back cover. When I bought my Smart-Clip, I bought the Testpoint adaptors set and I got hte Z3 testpoint adaptor with me. It's this one: (http://gsmserver.com/cables/cable_details.php?id=8594) Where do I put this adaptor to do the TP? A photo would be good And then do I go into smartmoto, select unlock, and unlock via tp? Help!!

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Vodafone FREE unlock solution! Multi-box JTAG testpoint adaptors for Vodafone unlock!	GSMtricks	Multi-box LITE	20	09-27-2008 15:57
Vodafone FREE unlock solution! Multi-box JTAG testpoint adaptors for Vodafone unlock!	GSMtricks	Main Sales Section	0	09-10-2008 10:17
Z3 Magic Testpoint-Adaptor For European Customers	mikolaj	Main Sales Section	0	04-23-2007 11:37
Motorola V3r Unlocking using testpoint (0A.52)	bbmad	Ultima Box Light	20	03-13-2007 10:22

02-06-2008, 10:59	#2 (permalink)
Mr.Tinkertrain No Life Poster Join Date: Feb 2006 Posts: 11,638 Member: 229997 Status: Offline Thanks Meter: 636	@ MeeM, in case if your phone has boot version A.C.0 or A.C.3. it can be unlocked via Prepare cycle. Check this link for more detailed information. Best Regards Smart-clip team www.smart-clip.com www.scoutdongle.com www.GsmServer.com www.boot-loader.com www.smart-unlocker.com

02-06-2008, 11:07	#3 (permalink)
MeeM Insane Poster Join Date: Dec 2007 Posts: 97 Member: 655243 Status: Offline Thanks Meter: 0	Ok, I'm downloading the new SmartMoto because the old version said to update. Then I will check the phone information in SmartMoto to see if the boot version is AC0 or AC3. If it is not, how do I do the TP? I have the testpoint adaptors but I can't find any instructions on how to use them or where to put them, and no one else seems to be using them...?

02-06-2008, 11:36	#5 (permalink)
MeeM Insane Poster Join Date: Dec 2007 Posts: 97 Member: 655243 Status: Offline Thanks Meter: 0	Ok ... there's another problem now. My smart-clip box is connected (with power supply and parallel connection to PC), and the red power light is on and the yellow/green E/G light is on. When i click 'connect' in smartmoto, the lights on the box turn off, and then smart-moto says smart-clip not found!. The lights on the box come back on after a few seconds. Why?! I have updated my smart dongle and the smart-clip, and the update software finds the dongle and clip without a problem. Why doesn't smartmoto find my clip? It finds my dongle, just not my clip. I have polling disabled on the parallel port. I'm using SmartMoto 3.07 European.

02-06-2008, 11:46	#6 (permalink)
Mr.Tinkertrain No Life Poster Join Date: Feb 2006 Posts: 11,638 Member: 229997 Status: Offline Thanks Meter: 636	@ MeeM, Please make sure that: 1. Firewall on your computer (or your LAN) is configured properly or disabled 2. LPT port settings are set to EPP in BIOS 3. Your LPT cable works properly 4. You use a stable power supply with your clip (use power adapter 12V 750mA) 5. If you are using WinXP, log in as Administrator or any other account with administrative rights To run a new SmartMoto under WinXP also to update a Smart-Clip please launch the SmartMoto, open Smart-Clip bookmark & tick the option "Disable OS parallel port polling (requires reboot)". After that restart you PC. Also set LPT options in SmartMoto to compatibility Best Regards Smart-clip team www.smart-clip.com www.scoutdongle.com www.GsmServer.com www.boot-loader.com www.smart-unlocker.com

02-06-2008, 12:01	#7 (permalink)
cbz_4383 Freak Poster Join Date: Jul 2007 Location: ********** Age: 36 Posts: 271 Member: 567351 Status: Offline** Thanks Meter: 40	@MeeM select LPT1 at smart clip option in smart moto . its not auto selected you have to do this 1 time after its no need.

02-06-2008, 12:13	#8 (permalink)
MeeM Insane Poster Join Date: Dec 2007 Posts: 97 Member: 655243 Status: Offline Thanks Meter: 0	ok ... smartmoto found my clip now. I would like to use my testpoint adaptor with the button on it, apparently it makes things easier for tp, but no one can tell me where to put it and what else to do!! anyone? phone boot version is ac3 so i can do the prepare, and it will unlock automatically ... so no TP hopefully! I'll let you know how it goes.

02-06-2008, 12:23	#9 (permalink)
MeeM Insane Poster Join Date: Dec 2007 Posts: 97 Member: 655243 Status: Offline Thanks Meter: 0	IT WORKED!! thanks a lot guys!

02-06-2008, 13:50	#10 (permalink)
MeeM Insane Poster Join Date: Dec 2007 Posts: 97 Member: 655243 Status: Offline Thanks Meter: 0	I guess my next question would be: does anyone have the Motorola testpoint adapters? If so, how do you know where to put them on the phone? And what procedure do you need to follow to unlock the phone? (ie when to put it on the phone, when to press the red button, etc.)

02-07-2008, 05:26	#12 (permalink)
MeeM Insane Poster Join Date: Dec 2007 Posts: 97 Member: 655243 Status: Offline Thanks Meter: 0	Ahh ok .. so you disassemble the phone, remove the LCD screen and disconnect it from the board, and put the Testpoint Adapter on the LCD connector on the board. That's what I needed to know. Thanks for the instructions. Will use them when the next V3 or Z3 comes in