Help please!!! cant repair imei zte blade a5 2020 [SOLVED]

[erocelmaster]

Try repair imei zte blade a5 2020 but not change, showme same imei:


Searching phone;
For an successful connection do the following:
1. Power on the phone and power it off and leave the battery inside
2. Keep pressed firmly volume DOWN key
3. Insert the usb cable inside the phone while keeping pressed volume DOWN
Phone detected (@oem210.inf,%usbcomm_dl%;SPRD U2S Diag) (Driver version: 4.19.38.134)
Preparing to sync;
Port opened [COM21];
Mobile type: SPRD3
Connected;
Starting;
FDL sent;
Syncing;
Loader version: Spreadtrum Boot Block version 1.1
Starting FDL2;
FDL2 sent;
Starting auth;
HW IMEI : 000000-00-000000-0

Analysing data; Please WAIT !
OK;
PHONE INFO: NONE
PHONE ID: MDI0YThlODcwMDkwMzVhNg==
BT ADDR: NONE
SW IMEI[0]: 865651-04-007734-3
SW IMEI[1]: 111111-11-111111-9
SW IMEI[2]: 867400-02-031663-8
SW IMEI[3]: 867400-02-031664-6

SIMLOCK FLAG: OFF

Reading NV;


NV saved to : NV_000000-00-000000-0_865651-04-007734-3_98550000_15_09_2020_12_00_32.spd
Gathering security data;
Security check result: 0
Re-programming;
Security programmed;
Sync NV;
Done;


Please helpme, dont change imei.

[AgicAga]

pay attention to the name you are fixing and select that name in the list 0 1 2 3

[erocelmaster]

Originally Posted by AgicAga

pay attention to the name you are fixing and select that name in the list 0 1 2 3

Select imei 1, its OK?

[erocelmaster]

Done in "diag mode" but now showme "invalid sim"

Searching phone;
For an successful connection do the following:
1. Connect the phone powered off with the battery inside to the usb cable
Phone detected (@oem210.inf,%usbcomm_dl%;SPRD U2S Diag) (Driver version: 4.19.38.134)
Preparing to sync;
Port opened [COM21];
Entering diagnostic mode;
Done;
Chip type: 0000:0000

Platform Version: MOCORTM_18B_W19.10.2_ZLA_P26_Debug
Project Version: sharkl3_pub
BASE Version: FM_BASE_18B_W19.10.2_ZLA_P26
HW Version: sc9863A_modem
06-22-2020 15:22:30
Build number: TEL_MX_P963F50V1.0.0B19
PHONE INFO:
BT ADDR:
SW IMEI[0]: 865651-04-007xxx-x
SW IMEI[1]: 865651-06-007xxx-x
SW IMEI[2]: 867400-02-031663-8
SW IMEI[3]: 867400-02-031664-6

SIMLOCK FLAG: OFF

Done;

IMEI[0] repaired; Remove battery and cable;


Imei change but showme "invalid sim" try select "remove sim lock"

Searching phone;
For an successful connection do the following:
1. Connect the phone powered off with the battery inside to the usb cable
Phone detected (@oem210.inf,%usbcomm_dl%;SPRD U2S Diag) (Driver version: 4.19.38.134)
Preparing to sync;
Port opened [COM21];
Entering diagnostic mode;
Done;
Chip type: 0000:0000

Platform Version: MOCORTM_18B_W19.10.2_ZLA_P26_Debug
Project Version: sharkl3_pub
BASE Version: FM_BASE_18B_W19.10.2_ZLA_P26
HW Version: sc9863A_modem
06-22-2020 15:22:30
Build number: TEL_MX_P963F50V1.0.0B19
PHONE INFO:
BT ADDR:
SW IMEI[0]: 865651-06-007xxx-x
SW IMEI[1]: 865651-06-007xxx-x
SW IMEI[2]: 867400-02-031663-8
SW IMEI[3]: 867400-02-031664-6

SIMLOCK FLAG: OFF


BKP saved to : BKP_000000-00-000000-0_865651-06-007734-8_00000000_15_09_2020_17_04_28.spd
SIM_LOCK TYPE: 0
ERROR: Simlock not enabled ! Phone is unlocked;

Please help me, imei repair imei done but now showme "invalid sim" thanks a lot!!!

[.:hack3r2k:.]

Originally Posted by erocelmaster

Select imei 1, its OK?

Is not ok . Must select IMEI[0] and repair from BOOT MODE !!!!!!! Do that and will work ! And never chnage imei from DIAG mode for secure models


Br

[erocelmaster]

Originally Posted by .:hack3r2k:.

Is not ok . Must select IMEI[0] and repair from BOOT MODE !!!!!!! Do that and will work ! And never chnage imei from DIAG mode for secure models


Br

Hi, try in "boot mode" and showme this:

Searching phone;
For an successful connection do the following:
1. Power on the phone and power it off and leave the battery inside
2. Keep pressed firmly volume DOWN key
3. Insert the usb cable inside the phone while keeping pressed volume DOWN
Phone detected (@oem210.inf,%usbcomm_dl%;SPRD U2S Diag) (Driver version: 4.19.38.134)
Preparing to sync;
Port opened [COM21];
Mobile type: SPRD3
Connected;
Starting;
FDL sent;
Syncing;
Loader version: Spreadtrum Boot Block version 1.1
Starting FDL2;
FDL2 sent;
Starting auth;
HW IMEI : 000000-00-000000-0
ERROR: Get info failed !
Reading NV;
ERROR: Read NV failed !


Thanks for answer

[.:hack3r2k:.]

Originally Posted by erocelmaster

Hi, try in "boot mode" and showme this:



Searching phone;

For an successful connection do the following:

1. Power on the phone and power it off and leave the battery inside

2. Keep pressed firmly volume DOWN key

3. Insert the usb cable inside the phone while keeping pressed volume DOWN

Phone detected (@oem210.inf,%usbcomm_dl%;SPRD U2S Diag) (Driver version: 4.19.38.134)

Preparing to sync;

Port opened [COM21];

Mobile type: SPRD3

Connected;

Starting;

FDL sent;

Syncing;

Loader version: Spreadtrum Boot Block version 1.1

Starting FDL2;

FDL2 sent;

Starting auth;

HW IMEI : 000000-00-000000-0

ERROR: Get info failed !

Reading NV;

ERROR: Read NV failed !





Thanks for answer

Power on /off and retry. Must connect same as it connected before

Br


Sent from my iPhone using Tapatalk Pro

[erocelmaster]

Originally Posted by .:hack3r2k:.

Power on /off and retry. Must connect same as it connected before

Br


Sent from my iPhone using Tapatalk Pro

Try but showme same outcome, so try instal backup "nvm file" and showme this:


Searching phone;
For an successful connection do the following:
1. Power on the phone and power it off and leave the battery inside
2. Keep pressed firmly volume DOWN key
3. Insert the usb cable inside the phone while keeping pressed volume DOWN
Phone detected (@oem210.inf,%usbcomm_dl%;SPRD U2S Diag) (Driver version: 4.19.38.134)
Preparing to sync;
Port opened [COM21];
Mobile type: SPRD3
Connected;
Starting;
FDL sent;
Syncing;
Loader version: Spreadtrum Boot Block version 1.1
Starting FDL2;
FDL2 sent;
Starting auth;
HW IMEI : 000000-00-000000-0
ERROR: Get info failed !
Uncompressing;
Done;
Re-programming;
ERROR: Simlock programming error !


please helpeme

[.:hack3r2k:.]

Originally Posted by erocelmaster

Try but showme same outcome, so try instal backup "nvm file" and showme this:





Searching phone;

For an successful connection do the following:

1. Power on the phone and power it off and leave the battery inside

2. Keep pressed firmly volume DOWN key

3. Insert the usb cable inside the phone while keeping pressed volume DOWN

Phone detected (@oem210.inf,%usbcomm_dl%;SPRD U2S Diag) (Driver version: 4.19.38.134)

Preparing to sync;

Port opened [COM21];

Mobile type: SPRD3

Connected;

Starting;

FDL sent;

Syncing;

Loader version: Spreadtrum Boot Block version 1.1

Starting FDL2;

FDL2 sent;

Starting auth;

HW IMEI : 000000-00-000000-0

ERROR: Get info failed !

Uncompressing;

Done;

Re-programming;

ERROR: Simlock programming error !





please helpeme

You do any usb sharing !? Because that can be a problem! Also try to install the drivers from the usb_driver and reboot the pc after.

Br


Sent from my iPhone using Tapatalk Pro

[erocelmaster]

Originally Posted by .:hack3r2k:.

You do any usb sharing !? Because that can be a problem! Also try to install the drivers from the usb_driver and reboot the pc after.

Br


Sent from my iPhone using Tapatalk Pro

Hi, will check drivers, reboot PC two times and showme same error "nvm"

Searching phone;
For an successful connection do the following:
1. Power on the phone and power it off and leave the battery inside
2. Keep pressed firmly volume DOWN key
3. Insert the usb cable inside the phone while keeping pressed volume DOWN
Phone detected (@oem138.inf,%dvcdsc%;SCI USB2Serial) (Driver version: 1.5.6.1)
Preparing to sync;
Port opened [COM21];
Mobile type: SPRD3
Connected;
Starting;
FDL sent;
Syncing;
Loader version: Spreadtrum Boot Block version 1.1
Starting FDL2;
FDL2 sent;
Starting auth;
HW IMEI : 000000-00-000000-0

Analysing data; Please WAIT !
OK;
PHONE INFO: NONE
PHONE ID: MDI0YThlODcwMDkwMzVhNg==
BT ADDR: NONE
SW IMEI[0]: 865651-06-007xxx-x
SW IMEI[1]: 865651-06-007xxx-x
SW IMEI[2]: 867400-02-031663-8
SW IMEI[3]: 867400-02-031664-6

SIMLOCK FLAG: OFF

Reading NV;
ERROR: Read NV failed !

Log file saved to: LOG_16_09_2020_14_46_54.txt


Time needed - 00:04:17


Try in "boot mode"

[.:hack3r2k:.]

Originally Posted by erocelmaster

Hi, will check drivers, reboot PC two times and showme same error "nvm"



Searching phone;

For an successful connection do the following:

1. Power on the phone and power it off and leave the battery inside

2. Keep pressed firmly volume DOWN key

3. Insert the usb cable inside the phone while keeping pressed volume DOWN

Phone detected (@oem138.inf,%dvcdsc%;SCI USB2Serial) (Driver version: 1.5.6.1)

Preparing to sync;

Port opened [COM21];

Mobile type: SPRD3

Connected;

Starting;

FDL sent;

Syncing;

Loader version: Spreadtrum Boot Block version 1.1

Starting FDL2;

FDL2 sent;

Starting auth;

HW IMEI : 000000-00-000000-0



Analysing data; Please WAIT !

OK;

PHONE INFO: NONE

PHONE ID: MDI0YThlODcwMDkwMzVhNg==

BT ADDR: NONE

SW IMEI[0]: 865651-06-007xxx-x

SW IMEI[1]: 865651-06-007xxx-x

SW IMEI[2]: 867400-02-031663-8

SW IMEI[3]: 867400-02-031664-6



SIMLOCK FLAG: OFF



Reading NV;

ERROR: Read NV failed !



Log file saved to: LOG_16_09_2020_14_46_54.txt





Time needed - 00:04:17





Try in "boot mode"

Did you check the phone battery!? Is strange is not connecting since you can see on first post it connected just fine. Pm me ammyy id and pass to connect and check


Br


Sent from my iPhone using Tapatalk Pro

[erocelmaster]

Originally Posted by .:hack3r2k:.

Did you check the phone battery!? Is strange is not connecting since you can see on first post it connected just fine. Pm me ammyy id and pass to connect and check


Br


Sent from my iPhone using Tapatalk Pro

Sure, teamviewer or what tool use?

[.:hack3r2k:.]

Originally Posted by erocelmaster

Sure, teamviewer or what tool use?

www.ammyy.com



Br

[erocelmaster]

Originally Posted by .:hack3r2k:.

www.ammyy.com



Br

ID: 88 590 265
Password:

[erocelmaster]

Searching phone;
For an successful connection do the following:
1. Power on the phone and power it off and leave the battery inside
2. Keep pressed firmly volume DOWN key
3. Insert the usb cable inside the phone while keeping pressed volume DOWN
Phone detected (@oem113.inf,%usbcomm_dl%;SPRD U2S Diag) (Driver version: 4.19.38.134)
Preparing to sync;
Port opened [COM18];
Mobile type: SPRD3
Connected;
Starting;
FDL sent;
Syncing;
Loader version: Spreadtrum Boot Block version 1.1
Starting FDL2;
FDL2 sent;
Starting auth;
HW IMEI : 000000-00-000000-0

Analysing data; Please WAIT !
OK;
PHONE INFO: NONE
PHONE ID: MDI0YThlODcwMDkwMzVhNg==
BT ADDR: NONE
SW IMEI[0]: 865651-04-007xxx-x
SW IMEI[1]: 111111-11-111111-9
SW IMEI[2]: 867400-02-031663-8
SW IMEI[3]: 867400-02-031664-6

SIMLOCK FLAG: OFF

Reading NV;


NV saved to : NV_000000-00-000000-0_865651-04-007734-3_98550000_18_09_2020_17_34_58.spd
Gathering security data;
Security check result: 0
Connecting to server;
Authorisation process started;
Done;

Requesting data from server ! Wait please ...

Re-programming;
Security programmed;
Sync NV;
Done;

IMEI[0] repaired; Remove battery and cable;


Done!! Thanks Mr. Hacker, my problem is my PC, try again in new pc format, great tool, great team, thanks a lot!!!