alcatel 9009g and tcl 8082 not booted

[elpring]

plz i need da for this tablet
alcatel 9009g
alcatel tcl 8082

Operation : Identify [ v2.12 ]
Mode : FLASH

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek USB Port_V1632 (COM23)
MODE : BOOTROM
PORT : 23
Waiting BOOT ack ...
BROM : Skip ACK verify
BROM : Init BROM

Error : Fail to init protocol!
>>> Remove battery, cable. Check cable/connection/driver! Check SW hint! Repeat operation!

Reconnect Power/Cable!

[Brka]

Recharge battery (on external power source), re-connect it to device, try identify again.

post log for each device.

p.s. Both are Mediatek MT8321, should identify till some point.

b.r.
Alex

[boganice]

Originally Posted by Brka

Recharge battery (on external power source), re-connect it to device, try identify again.

post log for each device.

p.s. Both are Mediatek MT8321, should identify till some point.

b.r.
Alex

PTFN : MTK USB Port (COM158)
MODE : BOOTROM
PORT : 158
Waiting BOOT ack ...
BROM : Skip ACK verify
BROM : Init BROM
BROM init passed!
     CHIP : MT6580 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000
     TYPE : LEGACY MTK
BROM : SecLevel : 0x00000007
BROM : SecMode  : SBC+SLA+SDA
BROM : BOOTROM
MODE : 0_base : BASE_v1712 | Manual : Disabled
AGENT : Look for suitable BootChain in DA ... 
AGENT : MTK_AllInOne_DA.bin
AGENT : Found MT6580
AGENT : MTK_DOWNLOAD_AGENT
     BROM : Sending 1st DA ...

  BROM  : 0x00000001 : DA SEND ERROR!
  ERROR : BROM : DL MODE ERROR
  INFO : BROM Level : SLA AUTH or AUTH required!

Error : Fail to init protocol!
>>> Remove battery, cable. Check cable/connection/driver! Check SW hint! Repeat operation!

Reconnect Power/Cable!

I think problem in DA file , also there's no da file available.

[inomfia]

Originally Posted by elpring

plz i need da for this tablet

alcatel 9009g

alcatel tcl 8082



Operation : Identify [ v2.12 ]

Mode : FLASH



1. Make sure device is powered off. Power off, if need. Wait 20 seconds after

2. Insert USB cable in phone

Waiting for device connection ...



PTFN : MediaTek USB Port_V1632 (COM23)

MODE : BOOTROM

PORT : 23

Waiting BOOT ack ...

BROM : Skip ACK verify

BROM : Init BROM



Error : Fail to init protocol!

>>> Remove battery, cable. Check cable/connection/driver! Check SW hint! Repeat operation!



Reconnect Power/Cable!

Connect it in preloader mode not bootrom. When you connect it first its detected as bootrom,then it switch to preloder.

Try to delay your desired operation by 3 to 4sec. Meaning of its frp remove , plug phon first then after 3sec hit reset tab. It worked for me

Sent from my SM-G570F using Tapatalk

[rebainoor]

Originally Posted by inomfia

Connect it in preloader mode not bootrom. When you connect it first its detected as bootrom,then it switch to preloder.

Try to delay your desired operation by 3 to 4sec. Meaning of its frp remove , plug phon first then after 3sec hit reset tab. It worked for me

Sent from my SM-G570F using Tapatalk

Cm2mt2 have option to choise only one mode if you need
If you need Preloader mode choise only Preloader mode only in cm2mt2 and will not detect BROM if mobile boot by default in BR

[inomfia]

Originally Posted by rebainoor

Cm2mt2 have option to choise only one mode if you need

If you need Preloader mode choise only Preloader mode only in cm2mt2 and will not detect BROM if mobile boot by default in BR

This alcatel 9009g works different from other mobiles. Just to confirm what im saying , go to device manager then plug in you device and check how the driver switches from mtk usb device to mtk preloader port then it starts to show charging.

Sent from my SM-G570F using Tapatalk

[rebainoor]

Originally Posted by inomfia

This alcatel 9009g works different from other mobiles. Just to confirm what im saying , go to device manager then plug in you device and check how the driver switches from mtk usb device to mtk preloader port then it starts to show charging.

Sent from my SM-G570F using Tapatalk

For that in this situation you need set in cm2mt2 PL (Preloader only) and correct DA for your mobile

[boganice]

Originally Posted by rebainoor

For that in this situation you need set in cm2mt2 PL (Preloader only) and correct DA for your mobile

No DA file available right now!!

[rebainoor]

in preloader mode only

8082_DA_PL

9009_DA_PL

[boganice]

Originally Posted by rebainoor

in preloader mode only

8082_DA_PL

9009_DA_PL

I've selected Perloader only and i have tried both DA files, Same problem too.


I have used MT2 V2.17 latest.