E96 china problem - GSM-Forum

Velko · 11-29-2007, 07:45

Nokia E96
If you phone power on read np

Phone detected, wait...
Hardware version: MT6226, E02
Hardware version: TELSDA26_05C_HW
Software version: MAUI.05C.W06.16.MP.V
Software date: 2005.04.12
Barcode: MT012345678901234567
imei: 353113010253601
Finished, time used: 13 sec
But i try to format ffs
Press and HOLD Power button now !
19200
error: boot phase#2/1 failed
Can't initialize test mode !
Possible reasons:
1. communication fault, repeat required operation
2. eeprom serious damaged, use repair eeprom files or use other unlock/format method
Operation failed !
Finished, time used: 6 sec

pin out
there is 4 dots:
1 2 3 4
Gnd Rx Tx

Phone after power with sim card phone restart .
Clasic problem.
Help
other interface this phone is 20 pin conector
Thanks

maheshsaiganesh · 11-29-2007, 09:42

Press and HOLD Power ............................select coplete mode try again working perfectely.

**InfinitySupport** · 11-29-2007, 17:31

@Velko
these phones ordinary has two rx/tx pairs (2 UARTs). If phone can't boot it's for sure problem with pinout.

Velko · 11-30-2007, 07:37

but where?
I find other point .Between 2 sim kard have 5 dot. 1 an 2 left end right rx,tx but resul same.

InfinityHelp · 11-30-2007, 13:39

hello!

check with multimeter maybe you found same pinout as before.
probably right pinout is in 20pin connector

11-29-2007, 07:45	#1 (permalink)
Velko No Life Poster Join Date: Mar 2001 Location: Bulgaria Age: 53 Posts: 1,024 Member: 3658 Status: Offline Thanks Meter: 66	E96 china problem Nokia E96 If you phone power on read np Phone detected, wait... Hardware version: MT6226, E02 Hardware version: TELSDA26_05C_HW Software version: MAUI.05C.W06.16.MP.V Software date: 2005.04.12 Barcode: MT012345678901234567 imei: 353113010253601 Finished, time used: 13 sec But i try to format ffs Press and HOLD Power button now ! 19200 error: boot phase#2/1 failed Can't initialize test mode ! Possible reasons: 1. communication fault, repeat required operation 2. eeprom serious damaged, use repair eeprom files or use other unlock/format method Operation failed ! Finished, time used: 6 sec pin out there is 4 dots: 1 2 3 4 Gnd Rx Tx Phone after power with sim card phone restart . Clasic problem. Help other interface this phone is 20 pin conector Thanks

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
E96 carging problem	aasif_ansari	Nokia Hardware & Hardware Repair	0	01-30-2010 12:50
N95 China Problem	neokia	CPF-BOX Ⅱ	22	10-12-2009 14:47
6300 China problem Infinity help	Shakeel_pattoki	Infinity-Box	3	09-02-2008 17:06
n73 China problem	cyberjhunz	SpiderMan	3	06-02-2008 05:45

11-29-2007, 09:42	#2 (permalink)
maheshsaiganesh No Life Poster Join Date: Jun 2006 Location: india Age: 47 Posts: 597 Member: 289913 Status: Offline Thanks Meter: 125	Press and HOLD Power ............................select coplete mode try again working perfectely.

11-29-2007, 17:31	#3 (permalink)
InfinitySupport Product Manager Join Date: Mar 2005 Location: infinity-box Posts: 38,635 Member: 130995 Status: Offline Thanks Meter: 35,227	@Velko these phones ordinary has two rx/tx pairs (2 UARTs). If phone can't boot it's for sure problem with pinout.

11-30-2007, 07:37	#4 (permalink)
Velko No Life Poster Join Date: Mar 2001 Location: Bulgaria Age: 53 Posts: 1,024 Member: 3658 Status: Offline Thanks Meter: 66	but where? I find other point .Between 2 sim kard have 5 dot. 1 an 2 left end right rx,tx but resul same.

11-30-2007, 13:39	#5 (permalink)
InfinityHelp Product Supporter Join Date: May 2005 Location: uae Posts: 29,245 Member: 148515 Status: Offline Thanks Meter: 19,534	hello! check with multimeter maybe you found same pinout as before. probably right pinout is in 20pin connector