error: can't set initial baud plzz help fly SLT 100 - GSM-Forum

ARAB GSM · 06-04-2008, 14:21

COM1 [Serial0] selected
Device: Fly-SLT100
Checking data, wait...
Action: write NAND flash
write: Firmware
skip: Customization/Language Pack
skip: Customization
skip: Eeprom/ffs
source data: page only
identification#1 protocol ver: 04
ver. sw1: SLT100_HMERID_PCB04_GPRS_MT6228_S02.MAUI_06A_W06_3 6_MP_V36.BIN
ver. sw2: MAUI.06A.W06.36.MP.V36, 00000000
ffs offset/size: 02000000/02000000
id-page1 Ok
nfi area detection finished: Ok
Boot...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing[6228:8A02:8A02]...
CPU: MT6228
chip: 0031:0000:0101
error: can't set initial baud
Release Power button now !
Boot Fail
Finished, time used: 37 sec
Remove/Install battery now !

**InfinitySupport** · 06-04-2008, 15:10

What was the reason to use bad qualioty cables instead of Infinity-Box ?
My advice: use good quality FTDI-based cable.

ARAB GSM · 06-04-2008, 16:44

every thing is ok now i unlocked my phone sussesfully,
BIG THANKS TO INFINITY TEAM AND EVERYBODY HERE.

**InfinitySupport** · 06-04-2008, 19:02

Thank you very much for test report !

Each test report with attached logs is very important for us so we can see how is Infinity-Box
software works and what is possible problems and successfully done work.

06-04-2008, 14:21	#1 (permalink)
ARAB GSM No Life Poster Join Date: Sep 2005 Location: West Africa Ghana Age: 15 Posts: 2,256 Member: 180675 Status: Offline Sonork: 100.111161 Thanks Meter: 411	error: can't set initial baud plzz help fly SLT 100 COM1 [Serial0] selected Device: Fly-SLT100 Checking data, wait... Action: write NAND flash write: Firmware skip: Customization/Language Pack skip: Customization skip: Eeprom/ffs source data: page only identification#1 protocol ver: 04 ver. sw1: SLT100_HMERID_PCB04_GPRS_MT6228_S02.MAUI_06A_W06_3 6_MP_V36.BIN ver. sw2: MAUI.06A.W06.36.MP.V36, 00000000 ffs offset/size: 02000000/02000000 id-page1 Ok nfi area detection finished: Ok Boot... Press and HOLD Power button now ! 19200 fixed Connecting, wait... Initializing[6228:8A02:8A02]... CPU: MT6228 chip: 0031:0000:0101 error: can't set initial baud Release Power button now ! Boot Fail Finished, time used: 37 sec Remove/Install battery now !

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
FLY SLT-100 UNLOCK (Thanks Infinity)	raja16sep	Infinity-Box	5	11-08-2009 02:36
fly slt-100 unlock problem	sebha	Infinity-Box	2	09-08-2009 14:42
Fly SLT 100 Flash problem	drancill	Infinity-Box	7	09-01-2009 11:35
5220 xpress music set not flash plzz help me plzzzzzzzz	faheemkhan	MT-BOX	0	03-31-2009 16:12
Fly Slt-100 Unlock Error !!!!	gsmjunction	Infinity-Box	4	01-28-2008 11:19

06-04-2008, 15:10	#2 (permalink)
InfinitySupport Product Manager Join Date: Mar 2005 Location: infinity-box Posts: 38,635 Member: 130995 Status: Offline Thanks Meter: 35,227	What was the reason to use bad qualioty cables instead of Infinity-Box ? My advice: use good quality FTDI-based cable.

06-04-2008, 16:44	#3 (permalink)
ARAB GSM No Life Poster Join Date: Sep 2005 Location: West Africa Ghana Age: 15 Posts: 2,256 Member: 180675 Status: Offline Sonork: 100.111161 Thanks Meter: 411	every thing is ok now i unlocked my phone sussesfully, BIG THANKS TO INFINITY TEAM AND EVERYBODY HERE.

06-04-2008, 19:02	#4 (permalink)
InfinitySupport Product Manager Join Date: Mar 2005 Location: infinity-box Posts: 38,635 Member: 130995 Status: Offline Thanks Meter: 35,227	Thank you very much for test report ! Each test report with attached logs is very important for us so we can see how is Infinity-Box software works and what is possible problems and successfully done work.