GSM-Forum

GSM-Forum (https://forum.gsmhosting.com/vbb/)
-   Infinity-Box (https://forum.gsmhosting.com/vbb/f296/)
-   -   inoi 2 Cannot Flash (https://forum.gsmhosting.com/vbb/f296/inoi-2-cannot-flash-2900846/)

Armkar 09-18-2020 11:12

inoi 2 Cannot Flash
 
Hi I have Inoi 2, but cannot read info and flash
log identyfy Brom+Preloader mode
Code:

Operation : Identify [ v2.15 ]
Mode : FLASH

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek USB Port (COM69)
MODE : BOOTROM
PORT : 69
Waiting BOOT ack ...
BROM : Skip ACK verify
BROM : Init BROM
BROM init passed!
    CHIP : MT6735 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000
    TYPE : LEGACY MTK
BROM : SecLevel : 0x00000005
BROM : SecMode  : SBC+SDA
BROM : BROM|BL  : 0x05|0xFE
BROM : BOOTROM
MODE : 0_base : BASE_v2028 | Manual : Disabled
AGENT : Look for suitable BootChain in DA ...
AGENT : DA_PL.bin
AGENT : Found MT6735
AGENT : MTK_DOWNLOAD_AGENT
    BROM : Sending 1st DA ...

  BROM  : 0x00007017 : DA SEND ERROR!
  ERROR : SECURE BOOT : SLA REQUIRED IN BROM MODE!
  INFO : BROM Level : CERT/AUTH required! Try boot device in PRELOADER mode with select PL/PL_CRYPTO/SWSEC type!

Error : Fail to init protocol!
>>> Remove battery, cable. Check cable/connection/driver! Check SW hint! Repeat operation!

Reconnect Power/Cable!

I try indentyfi only preloader mode but phone cannot boot in preloader mode, only brom mode
log identify only preloader mode
Code:

Operation : Identify [ v2.15 ]
Mode : FLASH

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PC show only phone Mediatec Usb Port (Com 46)

Please help me

rebainoor 09-18-2020 11:28

already in CM2MT2 :
select only : CM2MT2\boot\Teksun\XUNHU_MT6737

Armkar 09-18-2020 13:47

Thanks fot Advance
I connect phone !!! here log
Code:

Operation : Identify [ v2.15 ]
Mode : FLASH

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek USB Port (COM69)
MODE : BOOTROM
PORT : 69
Waiting BOOT ack ...
BROM : Skip ACK verify
BROM : Init BROM
BROM init passed!
    CHIP : MT6735 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000
    TYPE : LEGACY MTK
BROM : SecLevel : 0x00000005
BROM : SecMode  : SBC+SDA
BROM : BROM|BL  : 0x05|0xFE
BROM : BOOTROM
MODE : Teksun : XUNHU_MT6737 | Manual : Disabled
BROM : SLA
BROM : SLA Passed!
BROM : SLA CHLNG not used
AGENT : Look for suitable BootChain in DA ...
AGENT : MTK_AllInOne_DA.bin
AGENT : Found MT6735
AGENT : MTK_DOWNLOAD_AGENT
    BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ...
    DA : AGENT started!
NAND : DEVICE NOT FOUND
NAND : 000000000000000000000000
eMMC : BROM : DL MODE ERROR
eMMC : 00000000000000000000000000000000
DAInf: 4 : 2 : 155
DA : EXT_RAM NOT initialized!
eMMC : BROM : DL MODE ERROR
eMMC : 00000000000000000000000000000000
NAND : DEVICE NOT FOUND
NAND : 000000000000000000000000
DRAM : 0x0178
    EMI : DEV : INFINITY
    EMI : SRC : INFINITY-BOX_INTERNAL_EMIDB_v0
INIT : 0xBC : DRAM [ 0x00000000 :  [ 0 B ] ]
DRAM : DRAM: 0x20000000 [ 512,00 MB ]
    DA : DRAM ready!
DA : BOOT to 2nd DA ...
DA : Receiving HW info


        SRAM: 0x00020000 [ 128,00 KB ]
        DRAM: 0x20000000 [ 512,00 MB ]

        CHIP : MT6735 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000 , EVOL : 0x0000

        RNID : 9855A6B6B110054F545E3A13B5C2E804

 STATUS : BLANK FLASH
 BSTYLE : EMMC FLASH BOOT

DA : USB : FULL-SPEED
DA : USB : Change Port Speed
PTFN : MediaTek DA USB VCOM (Android) (COM78)
MODE : PRELOADER PORT
PORT : 78

>>> FATAL ERROR : NO ANY STORAGE DETECTED! Device HW fault or TestPoint hold!

But cannot flash
from this log I mean emmc is dead???
Code:

NAND : DEVICE NOT FOUND
NAND : 000000000000000000000000
eMMC : BROM : DL MODE ERROR
eMMC : 00000000000000000000000000000000
DAInf: 4 : 2 : 155
DA : EXT_RAM NOT initialized!
eMMC : BROM : DL MODE ERROR
eMMC : 00000000000000000000000000000000
NAND : DEVICE NOT FOUND
NAND : 000000000000000000000000
DRAM : 0x0178
    EMI : DEV : INFINITY
    EMI : SRC : INFINITY-BOX_INTERNAL_EMIDB_v0
INIT : 0xBC : DRAM [ 0x00000000 :  [ 0 B ] ]
DRAM : DRAM: 0x20000000 [ 512,00 MB ]
    DA : DRAM ready!
DA : BOOT to 2nd DA ...
DA : Receiving HW info


        SRAM: 0x00020000 [ 128,00 KB ]
        DRAM: 0x20000000 [ 512,00 MB ]

        CHIP : MT6735 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000 , EVOL : 0x0000

        RNID : 9855A6B6B110054F545E3A13B5C2E804

 STATUS : BLANK FLASH
 BSTYLE : EMMC FLASH BOOT

Or in Da file not have Emmc Config!!!!!!???

rebainoor 09-18-2020 15:10

if emmc is dead that mean is dead
and for that you cant connect in preloader mode

you can see in your log :
Quote:

eMMC : 00000000000000000000000000000000
replace it with new compatible emmc listed in preloader file


All times are GMT +1. The time now is 19:34.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2024 DragonByte Technologies Ltd.
- GSM Hosting Ltd. - 1999-2023 -

Page generated in 0.12012 seconds with 6 queries

SEO by vBSEO