possible flash via usb cable - GSM-Forum

green bird · 02-12-2008, 16:25

hi supporter and all readers; chinies phones flash (i don't have cable) possible via usb cable.
for ex. i have n82 dual sim but i don't have cable. i have usb cable i try to flash but get error.

COM11 ready
Action: read information
Model: Autodetect 6205-6227 NOR
Checking data, wait...
Phone should be Switched ON !
Connecting, wait...
Phone detected, wait...
Hardware version: MT6226, E02
Hardware version: MALATA26_05C_HW
Software version: MAUI.05C.W06.16"
Software date: 2005.04.12
Barcode: MT012345678901234567
imei: 135790246811220
Finished, time used: 4 sec
Power off phone now !

COM11 [USBSER001] selected
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
eeprom backup enabled, it may takes several minutes !
Action: write NOR flash
"smart write" active
write: Firmware
skip: Customization
skip: Language Pack
skip: Eeprom/ffs
Boot...
Press and HOLD Power button now !
baud autodetection active
9600
Connecting, wait...
error: boot phase#1 failed
Release Power button now !
in case of initial connection problem: on/off "Boot baudrate autoselect" box.
Boot Fail
Finished, time used: 4 sec
Remove/Install battery now !

**InfinitySupport** · 02-12-2008, 18:53

Hello,

you must use Rx/Tx/Gnd cable but not USB cable.

02-12-2008, 16:25	#1 (permalink)
green bird No Life Poster Join Date: Jan 2005 Location: IN YOUR HEART Posts: 714 Member: 109163 Status: Offline Thanks Meter: 75	possible flash via usb cable hi supporter and all readers; chinies phones flash (i don't have cable) possible via usb cable. for ex. i have n82 dual sim but i don't have cable. i have usb cable i try to flash but get error. COM11 ready Action: read information Model: Autodetect 6205-6227 NOR Checking data, wait... Phone should be Switched ON ! Connecting, wait... Phone detected, wait... Hardware version: MT6226, E02 Hardware version: MALATA26_05C_HW Software version: MAUI.05C.W06.16" Software date: 2005.04.12 Barcode: MT012345678901234567 imei: 135790246811220 Finished, time used: 4 sec Power off phone now ! COM11 [USBSER001] selected Device: Autodetect 6205-6227 NOR Checking data, wait... advanced flash detection enabled eeprom backup enabled, it may takes several minutes ! Action: write NOR flash "smart write" active write: Firmware skip: Customization skip: Language Pack skip: Eeprom/ffs Boot... Press and HOLD Power button now ! baud autodetection active 9600 Connecting, wait... error: boot phase#1 failed Release Power button now ! in case of initial connection problem: on/off "Boot baudrate autoselect" box. Boot Fail Finished, time used: 4 sec Remove/Install battery now !

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
how to flash bb5 phone's via usb cable??	msantar	MXKEY Nokia Flasher and Unlocker (by Alim Hape)	0	08-10-2009 19:37
Flash c650 via usb cable	venceslau	Motorola P2k	4	06-08-2007 09:42

02-12-2008, 18:53	#2 (permalink)
InfinitySupport Product Manager Join Date: Mar 2005 Location: infinity-box Posts: 38,635 Member: 130995 Status: Offline Thanks Meter: 35,227	Hello, you must use Rx/Tx/Gnd cable but not USB cable.