Qmobile T200 dead after flash - GSM-Forum

malikawan · 09-15-2016, 12:00

Qmobile t200 is alive only problem is call auto attend i flash it and after flash mobile is dead i again redownload file and flash but result is same i also covert InfinitySC to SPRD PAC and flash with factory tool. Flash successfully but set never on. Logs are here

Phone found! [ 6 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SPRD 773x eMMC loader v3 Infinity
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

FLASH : eMMC Flash , Structure : Ok!

Reading extended info ...

Model Name : QMobile T200
Model Brand : QMobile T200
Model Device: QMobile
AndrVersion : 4.4.3
BaseBand CPU: SP7731GEA
CompileDate : 4/4/2015 9:05:24 AM
Project Ver : QMobileT200_MP_11_04
Model Ext : QMobile T200

ExtraInfo : HWInfo exists!!! This phone have DYNAMIC HW settings!!!

Phone found! [ 6 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC773x Android 5.x eMMC v1.0 Inf
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

FlashMode Set : Ok!

PMTManager : Load 0x18 records
PMTManager : PMT Update Ok!
Flashing now

Update BootCode : u-boot-spl-16k.bin
Write Data ...
Write Data Ok!

Update BootCode : u-boot.bin
Erase block ...
Block erase Ok!
Write Data ...
Write Data Ok!

Write FSImage : prodnv.img
Write Data ...
Write Data Ok!

Write CodeData : sc7731g_CP0_modem.bin
Write Data ...
Write Data Ok!

Write CodeData : DSP_DM_Gx.bin
Write Data ...
Write Data Ok!

Erase Block : RuntimeData
Erase block ...
Block erase Ok!

Write CodeData : sc7731g_modem_CP2_WCN_14E_W15.16_Release.bin
Write Data ...
Write Data Ok!

Erase Block : RuntimeData
Erase block ...
Block erase Ok!

Write CodeData : logo_480x800.bin
Write Data ...
Write Data Ok!

Write CodeData : hwinfo.bin
Write Data ...
Write Data Ok!

Write CodeData : boot.img
Write Data ...
Write Data Ok!

Write FSImage : system.img
Write Data ...
Write Data Ok!

Write FSImage : cache.img
Write Data ...
FSImage : Make and Flush SPImage
Write Data Ok!

Write CodeData : recovery.img
Write Data ...
Write Data Ok!

Process : Flush
Flush Ok!

Write FSImage : userdata.img
Write Data ...
FSImage : Make and Flush SPImage
Write Data Ok!

Erase Block : INTERNALSD
Erase block ...
Block erase Ok!

JayDi · 09-15-2016, 14:24

1. What is Identify log now?
2. What is "Flash IC Test" result?

GSM-JAHIDHASSAN · 09-15-2016, 14:27

ROM QMobile Bolt T200 SPD 7731 Officail File | [Official]-[Updated] add the 02/21/2016 on Needrom

malikawan · 09-15-2016, 14:31

identify logs
Phone found! [ 6 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SPRD 773x eMMC loader v3 Infinity
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

FLASH : eMMC Flash , Structure : Ok!

Reading extended info ...

Model Name : QMobile T200
Model Brand : QMobile T200
Model Device: QMobile
AndrVersion : 4.4.3
BaseBand CPU: SP7731GEA
CompileDate : 4/4/2015 9:05:24 AM
Project Ver : QMobileT200_MP_11_04
Model Ext : QMobile T200

ExtraInfo : HWInfo exists!!! This phone have DYNAMIC HW settings!!!

Flash IC Test

Phone found! [ 97 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SPRD 773x eMMC loader v3 Infinity
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

FlashMode Set : Ok!
Checking Structure ...
Detected eMMC Flash , Structure detect Ok!

Prepare test data ...
Test flow #0 ...
Test flow passed!
Test flow #1 ...
Test flow passed!
Test flow #2 ...
Test flow passed!
Test flow #3 ...
Test flow passed!
Test flow #4 ...
Test flow passed!
Test flow #5 ...
Test flow passed!

Finalize Ok!
Test passed successfully!

JayDi · 09-15-2016, 14:32

Quote:

Originally Posted by GSM-JAHIDHASSAN

ROM QMobile Bolt T200 SPD 7731 Officail File | [Official]-[Updated] add the 02/21/2016 on Needrom

Seems as you forget to learn how check links by yourself, before stupidly post them.

JayDi · 09-15-2016, 14:34

Quote:

Originally Posted by malikawan

identify logs
Phone found! [ 6 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SPRD 773x eMMC loader v3 Infinity
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

FLASH : eMMC Flash , Structure : Ok!

Reading extended info ...

Model Name : QMobile T200
Model Brand : QMobile T200
Model Device: QMobile
AndrVersion : 4.4.3
BaseBand CPU: SP7731GEA
CompileDate : 4/4/2015 9:05:24 AM
Project Ver : QMobileT200_MP_11_04
Model Ext : QMobile T200

ExtraInfo : HWInfo exists!!! This phone have DYNAMIC HW settings!!!

Flash IC Test

Phone found! [ 97 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SPRD 773x eMMC loader v3 Infinity
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

FlashMode Set : Ok!
Checking Structure ...
Detected eMMC Flash , Structure detect Ok!

Prepare test data ...
Test flow #0 ...
Test flow passed!
Test flow #1 ...
Test flow passed!
Test flow #2 ...
Test flow passed!
Test flow #3 ...
Test flow passed!
Test flow #4 ...
Test flow passed!
Test flow #5 ...
Test flow passed!

Finalize Ok!
Test passed successfully!

If you already upgrade Infinity FW and flash it ( I see just old FW flashing ) - then left only option to take alive phone and make read FW from it again, then flash to that.

malikawan · 09-15-2016, 14:39

i already have another same working set and i read flash from it and flash the set but set not alive and also download another file from internet and flash but not solve.
i dont understand what u mean Infinity FW upgrade. U mean upgrade by dongle manager.

JayDi · 09-15-2016, 14:52

In Extra tab in CM2SPD ( left up corner of SW ) - there is 2 options - upgrade FW and Convert. Anyway - convert do upgrade also.

malikawan · 09-15-2016, 14:56

i also mention in my first post that i convert the FW and flash with factory tool. Flash success but set not alive.

JayDi · 09-15-2016, 15:29

Can you make photo of phones back stickers?
Ineterst SN and HW rev code.

malikawan · 09-15-2016, 15:38

Phone back sticker only imei nos and model no mention no SN or HW rev code

JayDi · 09-15-2016, 16:38

Hm.
Make Flash Erase and reflash PAC or Infinity SC file.

malikawan · 09-15-2016, 17:02

after flash erase and reflash with infinity same condition set not alive here is logs:
Phone found! [ 97 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SPRD 773x eMMC loader v3 Infinity
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

FlashMode Set : Ok!
Erasig flash now, please wait ...
Format finished! Reflash phone with normal FW now!

Phone found! [ 97 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SPRD 773x eMMC loader v3 Infinity
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

FlashMode Set : Ok!

PMTManager : Load 0x18 records
PMTManager : PMT Update Ok!
Flashing now

Update BootCode : u-boot-spl-16k.bin
Write Data ...
Write Data Ok!

Update BootCode : u-boot.bin
Erase block ...
Block erase Ok!
Write Data ...
Write Data Ok!

Write FSImage : prodnv.img
Write Data ...
Write Data Ok!

Write CodeData : sc7731g_CP0_modem.bin
Write Data ...
Write Data Ok!

Write CodeData : DSP_DM_Gx.bin
Write Data ...
Write Data Ok!

Erase Block : RuntimeData
Erase block ...
Block erase Ok!

Write CodeData : sc7731g_modem_CP2_WCN_14E_W15.16_Release.bin
Write Data ...
Write Data Ok!

Erase Block : RuntimeData
Erase block ...
Block erase Ok!

Write CodeData : logo_480x800.bin
Write Data ...
Write Data Ok!

Write CodeData : fblogo.bin
Write Data ...
Write Data Ok!

Write CodeData : boot.img
Write Data ...
Write Data Ok!

Write FSImage : system.img
Write Data ...
Write Data Ok!

Write FSImage : cache.img
Write Data ...
FSImage : Make and Flush SPImage
Write Data Ok!

Write CodeData : recovery.img
Write Data ...
Write Data Ok!

Process : Flush
Flush Ok!

Write FSImage : userdata.img
Write Data ...
FSImage : Make and Flush SPImage
Write Data Ok!

Erase Block : INTERNALSD
Erase block ...
Block erase Ok!

JayDi · 09-15-2016, 17:20

I seen NOT updated Infinity FW flashing.
Also use always latest CM2SPD version.

malikawan · 09-15-2016, 17:25

Dongle is up-to-date and has latest firmware and i also used spreadtrum module 1.21. Ok i got your point i read flash with 1.21 and then try again.

09-15-2016, 12:00	#1 (permalink)
malikawan No Life Poster Join Date: Feb 2007 Location: pakistan Posts: 514 Member: 456932 Status: Offline Thanks Meter: 53	Qmobile T200 dead after flash Qmobile t200 is alive only problem is call auto attend i flash it and after flash mobile is dead i again redownload file and flash but result is same i also covert InfinitySC to SPRD PAC and flash with factory tool. Flash successfully but set never on. Logs are here Phone found! [ 6 ] Port Opened Sync... InitBoot Done [ 0x81 ] , Ver : SPRD3 Sync... Sending FDL [Info] : If SW freeze here more, than 15 seconds - remove cable FDL Ready! Boot Ver : SPRD 773x eMMC loader v3 Infinity Sending FLASH FDL FLASH FDL Ready! Boot Ok! FLASH : eMMC Flash , Structure : Ok! Reading extended info ... Model Name : QMobile T200 Model Brand : QMobile T200 Model Device: QMobile AndrVersion : 4.4.3 BaseBand CPU: SP7731GEA CompileDate : 4/4/2015 9:05:24 AM Project Ver : QMobileT200_MP_11_04 Model Ext : QMobile T200 ExtraInfo : HWInfo exists!!! This phone have DYNAMIC HW settings!!! Phone found! [ 6 ] Port Opened Sync... InitBoot Done [ 0x81 ] , Ver : SPRD3 Sync... Sending FDL [Info] : If SW freeze here more, than 15 seconds - remove cable FDL Ready! Boot Ver : SC773x Android 5.x eMMC v1.0 Inf Sending FLASH FDL FLASH FDL Ready! Boot Ok! FlashMode Set : Ok! PMTManager : Load 0x18 records PMTManager : PMT Update Ok! Flashing now Update BootCode : u-boot-spl-16k.bin Write Data ... Write Data Ok! Update BootCode : u-boot.bin Erase block ... Block erase Ok! Write Data ... Write Data Ok! Write FSImage : prodnv.img Write Data ... Write Data Ok! Write CodeData : sc7731g_CP0_modem.bin Write Data ... Write Data Ok! Write CodeData : DSP_DM_Gx.bin Write Data ... Write Data Ok! Erase Block : RuntimeData Erase block ... Block erase Ok! Write CodeData : sc7731g_modem_CP2_WCN_14E_W15.16_Release.bin Write Data ... Write Data Ok! Erase Block : RuntimeData Erase block ... Block erase Ok! Write CodeData : logo_480x800.bin Write Data ... Write Data Ok! Write CodeData : hwinfo.bin Write Data ... Write Data Ok! Write CodeData : boot.img Write Data ... Write Data Ok! Write FSImage : system.img Write Data ... Write Data Ok! Write FSImage : cache.img Write Data ... FSImage : Make and Flush SPImage Write Data Ok! Write CodeData : recovery.img Write Data ... Write Data Ok! Process : Flush Flush Ok! Write FSImage : userdata.img Write Data ... FSImage : Make and Flush SPImage Write Data Ok! Erase Block : INTERNALSD Erase block ... Block erase Ok!

09-15-2016, 17:25	#15 (permalink)
malikawan No Life Poster Join Date: Feb 2007 Location: pakistan Posts: 514 Member: 456932 Status: Offline Thanks Meter: 53	Dongle is up-to-date and has latest firmware and i also used spreadtrum module 1.21. Ok i got your point i read flash with 1.21 and then try again. Last edited by malikawan; 09-15-2016 at 17:34.

09-15-2016, 14:24	#2 (permalink)
JayDi No Life Poster Join Date: Mar 2007 Location: Where you live Posts: 18,542 Member: 462970 Status: Offline Thanks Meter: 20,352	1. What is Identify log now? 2. What is "Flash IC Test" result?

09-15-2016, 14:27	#3 (permalink)
GSM-JAHIDHASSAN Freak Poster Join Date: Jul 2016 Location: Muscat For oman Posts: 190 Member: 2604747 Status: Offline Sonork: 100.1648061 Thanks Meter: 112	ROM QMobile Bolt T200 SPD 7731 Officail File \| [Official]-[Updated] add the 02/21/2016 on Needrom

09-15-2016, 14:31	#4 (permalink)
malikawan No Life Poster Join Date: Feb 2007 Location: pakistan Posts: 514 Member: 456932 Status: Offline Thanks Meter: 53	identify logs Phone found! [ 6 ] Port Opened Sync... InitBoot Done [ 0x81 ] , Ver : SPRD3 Sync... Sending FDL [Info] : If SW freeze here more, than 15 seconds - remove cable FDL Ready! Boot Ver : SPRD 773x eMMC loader v3 Infinity Sending FLASH FDL FLASH FDL Ready! Boot Ok! FLASH : eMMC Flash , Structure : Ok! Reading extended info ... Model Name : QMobile T200 Model Brand : QMobile T200 Model Device: QMobile AndrVersion : 4.4.3 BaseBand CPU: SP7731GEA CompileDate : 4/4/2015 9:05:24 AM Project Ver : QMobileT200_MP_11_04 Model Ext : QMobile T200 ExtraInfo : HWInfo exists!!! This phone have DYNAMIC HW settings!!! Flash IC Test Phone found! [ 97 ] Port Opened Sync... InitBoot Done [ 0x81 ] , Ver : SPRD3 Sync... Sending FDL [Info] : If SW freeze here more, than 15 seconds - remove cable FDL Ready! Boot Ver : SPRD 773x eMMC loader v3 Infinity Sending FLASH FDL FLASH FDL Ready! Boot Ok! FlashMode Set : Ok! Checking Structure ... Detected eMMC Flash , Structure detect Ok! Prepare test data ... Test flow #0 ... Test flow passed! Test flow #1 ... Test flow passed! Test flow #2 ... Test flow passed! Test flow #3 ... Test flow passed! Test flow #4 ... Test flow passed! Test flow #5 ... Test flow passed! Finalize Ok! Test passed successfully!

09-15-2016, 14:39	#7 (permalink)
malikawan No Life Poster Join Date: Feb 2007 Location: pakistan Posts: 514 Member: 456932 Status: Offline Thanks Meter: 53	i already have another same working set and i read flash from it and flash the set but set not alive and also download another file from internet and flash but not solve. i dont understand what u mean Infinity FW upgrade. U mean upgrade by dongle manager.

09-15-2016, 14:52	#8 (permalink)
JayDi No Life Poster Join Date: Mar 2007 Location: Where you live Posts: 18,542 Member: 462970 Status: Offline Thanks Meter: 20,352	In Extra tab in CM2SPD ( left up corner of SW ) - there is 2 options - upgrade FW and Convert. Anyway - convert do upgrade also.

09-15-2016, 14:56	#9 (permalink)
malikawan No Life Poster Join Date: Feb 2007 Location: pakistan Posts: 514 Member: 456932 Status: Offline Thanks Meter: 53	i also mention in my first post that i convert the FW and flash with factory tool. Flash success but set not alive.

09-15-2016, 15:29	#10 (permalink)
JayDi No Life Poster Join Date: Mar 2007 Location: Where you live Posts: 18,542 Member: 462970 Status: Offline Thanks Meter: 20,352	Can you make photo of phones back stickers? Ineterst SN and HW rev code.

09-15-2016, 15:38	#11 (permalink)
malikawan No Life Poster Join Date: Feb 2007 Location: pakistan Posts: 514 Member: 456932 Status: Offline Thanks Meter: 53	Phone back sticker only imei nos and model no mention no SN or HW rev code

09-15-2016, 16:38	#12 (permalink)
JayDi No Life Poster Join Date: Mar 2007 Location: Where you live Posts: 18,542 Member: 462970 Status: Offline Thanks Meter: 20,352	Hm. Make Flash Erase and reflash PAC or Infinity SC file.

09-15-2016, 17:02	#13 (permalink)
malikawan No Life Poster Join Date: Feb 2007 Location: pakistan Posts: 514 Member: 456932 Status: Offline Thanks Meter: 53	after flash erase and reflash with infinity same condition set not alive here is logs: Phone found! [ 97 ] Port Opened Sync... InitBoot Done [ 0x81 ] , Ver : SPRD3 Sync... Sending FDL [Info] : If SW freeze here more, than 15 seconds - remove cable FDL Ready! Boot Ver : SPRD 773x eMMC loader v3 Infinity Sending FLASH FDL FLASH FDL Ready! Boot Ok! FlashMode Set : Ok! Erasig flash now, please wait ... Format finished! Reflash phone with normal FW now! Phone found! [ 97 ] Port Opened Sync... InitBoot Done [ 0x81 ] , Ver : SPRD3 Sync... Sending FDL [Info] : If SW freeze here more, than 15 seconds - remove cable FDL Ready! Boot Ver : SPRD 773x eMMC loader v3 Infinity Sending FLASH FDL FLASH FDL Ready! Boot Ok! FlashMode Set : Ok! PMTManager : Load 0x18 records PMTManager : PMT Update Ok! Flashing now Update BootCode : u-boot-spl-16k.bin Write Data ... Write Data Ok! Update BootCode : u-boot.bin Erase block ... Block erase Ok! Write Data ... Write Data Ok! Write FSImage : prodnv.img Write Data ... Write Data Ok! Write CodeData : sc7731g_CP0_modem.bin Write Data ... Write Data Ok! Write CodeData : DSP_DM_Gx.bin Write Data ... Write Data Ok! Erase Block : RuntimeData Erase block ... Block erase Ok! Write CodeData : sc7731g_modem_CP2_WCN_14E_W15.16_Release.bin Write Data ... Write Data Ok! Erase Block : RuntimeData Erase block ... Block erase Ok! Write CodeData : logo_480x800.bin Write Data ... Write Data Ok! Write CodeData : fblogo.bin Write Data ... Write Data Ok! Write CodeData : boot.img Write Data ... Write Data Ok! Write FSImage : system.img Write Data ... Write Data Ok! Write FSImage : cache.img Write Data ... FSImage : Make and Flush SPImage Write Data Ok! Write CodeData : recovery.img Write Data ... Write Data Ok! Process : Flush Flush Ok! Write FSImage : userdata.img Write Data ... FSImage : Make and Flush SPImage Write Data Ok! Erase Block : INTERNALSD Erase block ... Block erase Ok!

09-15-2016, 17:20	#14 (permalink)
JayDi No Life Poster Join Date: Mar 2007 Location: Where you live Posts: 18,542 Member: 462970 Status: Offline Thanks Meter: 20,352	I seen NOT updated Infinity FW flashing. Also use always latest CM2SPD version.