Successfully unlocked/repaired phones by Infinity-Box - Page 4602 - GSM-Forum

Tanha0321 · 12-18-2021, 18:43

Code:

Brand     : QMobile
ProdName  : QMobile L15
ProdModel : QMobile L15
Device    : QMobile
AndroidVer: 5.0
MTKxCPU   : MT6582
MTKxPRJ   : ALPS.L0.MP2.V1_TINNO6582.WT.L_P7

Done!
Elapsed: 00:00:06
Reconnect Power/Cable!


Scatter Load Ok , BaseBand : MT6582 , Project : s5400 , Storage : EMMC
Files found : 11 , Set to Flash : 10
Ready to Flash!

Operation : Flash [ v1.58 ]

======= Flash
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 12 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6582
BB_CPU_NME : [MediaTek] MT6582_S00
BB_CPU_EXT : 0xCA01 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer   : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x87
NAND Flash : NOT INSTALLED
eMMC Flash : 90014A483847316505074EA148CF725F
Initialize Memory ... 
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x90 , OEM : 014A
[eMMC] : FLASH_INF : [HYNIX] , e1G8
[eMMC] : FLASH_CID : 90014A483847316505074EA148CF725F
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00400000
[eMMC] : FLASH_LEN : 0x00000001D2000000
[eMMC] : FLASH_UCP : 7456 MiB [eMMC 8 GiB]
DEV RID    : 0xD5229C25E90CD58B7477C14EFDDEBB8E
INT RAM    : 0x00020000
EXT RAM    : 0x40000000 [1 GiB]
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

ScatCFG : BaseBand : MT6582 , Project : s5400 , Storage : EMMC
Setting : Flash Pre-Erase (Safe) : Enabled
Setting : AFF verify :  Disabled
Setting : HW verify :  Enabled

BL : Check HW compatibility
BL : BBID supported by BootLoader!
BL : Check eMMC compatibility
BL : eMMC supported by BootLoader!

BL : BatteryLevel : 4021 mV
BL : BatteryLevel Ok

BL : Flash Pre-Erase
Total blocks to Erase : 2
Erase : 0x0000000000C00000-0x0000000000100000
Erase : 0x0000000002900000-0x00000001CEE00000
Flash Pre-Erase Done, time used : 00:00:09

SecCfg Passed , 1799
BMT remark not need. Will skip
Sending Preloader ... 
Use : preloader_s5400.bin
Preloader Sent , Init passed
SecCfg Passed , 1799
PartCount : 0012
Update PMT by user request
Repartition Done!
Use FLN Mode

Processing : Flash Write
Flash now : MBR
Image Flash Ok
Flash now : EBR1
Image Flash Ok
Flash now : UBOOT
Image Flash Ok
Flash now : BOOTIMG
Image Flash Ok
Flash now : RECOVERY
Image Flash Ok
Flash now : SEC_RO
Image Flash Ok
Flash now : LOGO
Image Flash Ok
Flash now : ANDROID
Image Flash Ok
Flash now : CACHE
Image Flash Ok
Flash now : USRDATA
Image Flash Ok
Flash Write Done, time used : 00:03:48


Update Mirror PMT
Update Done!

Update RomInfo done

Done!
Elapsed: 00:04:10
Reconnect Power/Cable!

Tanha0321 · 12-18-2021, 18:44

Code:

Brand     : motorola
ProdName  : woods_retail
ProdModel : Moto E (4)
Device    : woods
AndroidVer: 7.1.1
MTKxCPU   : MT6737M
MTKxPRJ   : alps-mp-n1.mp1-V1_lenovo6737m.35.n1_P129

Done!
Elapsed: 00:00:09
Reconnect Power/Cable!


Operation : Format FileSystem [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 12 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6737
BB_CPU_NME : [MediaTek] MT6737M|MT6737_S00
BB_CPU_EXT : 0xCB00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x01000000
BromVer   : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : SIGNED with SPRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x93
NAND Flash : NOT INSTALLED
eMMC Flash : 484A0190613447415804A532834B2F01
Initialize Memory ... 
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x90 , OEM : 014A
[eMMC] : FLASH_INF : [HYNIX] , 2a4GA
[eMMC] : FLASH_CID : 90014A484147346132A50458012F5483
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00400000
[eMMC] : FLASH_LEN : 0x00000003AB400000
[eMMC] : FLASH_UCP : 15028 MiB [eMMC 16 GiB]
DEV RID    : 0xD5229C2593B2F8BB382CDEC9D307659E
INT RAM    : 0x00020000
EXT RAM    : 0x80000000 [2 GiB]
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!


Clear FRP ( Google Reset Protection )
Clear Ok!

Done!
Elapsed: 00:00:15
Reconnect Power/Cable!

Tanha0321 · 12-18-2021, 18:45

Code:

Product Brand  : TECNO
Product Model  : TECNO BB2
Product Name   : BB2-OP
Product Device : TECNO-BB2
Product Board  : BB2
Patch Level    : QP1A.190711.020
Display ID     : BB2-VP572DE-QGo-OP-210812V011
Ver. CodeName  : REL
Ver. Release   : 10
Sec. Patch     : 2021-08-05
Build Time     : 16.08.2021
Product Info   : k80hd_bsp_fwv_512m
Product Board  : k80hd_bsp_fwv_512m
Board Platform : mt6580
Product Manfct : TECNO MOBILE LIMITED

USERDATA : FILESYSTEM : F2FS  with FBE ( File-Base Encryption )

NVRAM : 0x6D028DDC
NVRAM : State : Ok!
INFO  : WiFi MAC : CC3B27FA02F1
INFO  : BlTh MAC : CC3B27FA02F0
INFO  : IMEI[1] : 
INFO  : IMEI[2] : 


Done!
Elapsed: 00:00:33

Operation : Reset Settings/Format FS [ v2.28 ]

Mode : FRP [ RESET PROTECTION ]

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek PreLoader USB VCOM_V1632 (Android) (COM12)
MODE : PRELOADER PORT
PORT : 12
Waiting BOOT ack ...
PRELOADER : ACK confirmed!
BROM : Init BROM
BROM init passed!
     CHIP : MT6580 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000
     TYPE : LEGACY [MTK]
BROM : SecLevel : 0x00000005
BROM : SecMode  : SBC+SDA
BROM : BROM|BL  : 0xFF|0x01
BROM : PRELOADER PORT
BROM : PreBoot stage #1
BROM : PreBoot stage #2
AGENT : 0_base : BASE_v1712 | Manual : Disabled
AGENT : Look for suitable BootChain in DA ... 
AGENT : MTK_AllInOne_DA.bin
AGENT : Found MT6580
AGENT : MTK_DOWNLOAD_AGENT
     BROM : Sending 1st DA ...
     BROM : Reset Interface!
PTFN : MediaTek USB Port_V1632 (COM11)
MODE : BOOTROM
PORT : 11
Waiting BOOT ack ...
BROM : Skip ACK verify
BROM : Init BROM
BROM init passed!
     CHIP : MT6580 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000
     TYPE : LEGACY [MTK]
BROM : MEID : BAF214B370EA0F91BF9F529F7B8F44B1
BROM : SecLevel : 0x00000005
BROM : SecMode  : SBC+SDA
BROM : BROM|BL  : 0x05|0xFE
BROM : BOOTROM
BROM : SLA : Local Auth 
BROM : SLA : Auth Started!
BROM : SLA : Auth Passed!
BROM : SLA : 0x000000FE
BROM : PreBoot stage #1
BROM : PreBoot stage #2
AGENT : 0_base : BASE_v1712 | Manual : Disabled
AGENT : Look for suitable BootChain in DA ... 
AGENT : MTK_AllInOne_DA.bin
AGENT : Found MT6580
AGENT : MTK_DOWNLOAD_AGENT
     BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ... 
     DA : AGENT started!
NAND : DEVICE NOT FOUND
NAND : 000000000000000000000000
eMMC : OK
eMMC : 4600011541323645FA56094247180A07
DAInf: 4 : 2 : 156
DA : EXT_RAM NOT initialized!
eMMC : OK
eMMC : 1501004645363241420956FA070A1847
NAND : DEVICE NOT FOUND
NAND : 000000000000000000000000
DRAM : 0x0178
     EMI : DEV : FireFly
     EMI : SRC : preloader_k80hd_bsp_fwv_512m.bin
     EMI : CNT : 0003
     EMI : [00] : ID : 150100464536324D42 : VEN : SAMSUNG   | DEV : FE62MB : RAM : [ 1.00 GB ]
     EMI : [01] : ID : 700100464D41454538 : VEN : KINGSTON  | DEV : FMAEE8 : RAM : [ 1.00 GB ]
     EMI : [02] : ID : 150100464536324142 : VEN : SAMSUNG   | DEV : FE62AB : RAM : [ 1.00 GB ]
     EMI : Init EMI from PRELOADER
INIT : 0xBC : DRAM [ 0x00000000 :  [ 0 B ] ]
DRAM : DRAM: 0x40000000 [ 1.00 GB ]
     DA : DRAM ready!
DA : BOOT to 2nd DA ...
DA : Receiving HW info

        EMMC: CID : 1501004645363241420956FA070A1847
        EMMC: VEN : SAMSUNG : OEM : 0 : ID : 464536324142
        EMMC: VEN : SAMSUNG : FE62AB
        EMMC: SNN : 1459226378 ( 0x56FA070A) , MF : 1/2021

        EMMC: 
              BOOT1  : 0x00400000 [ 4.00 MB ]
              BOOT2  : 0x00400000 [ 4.00 MB ]
              RPMB   : 0x00400000 [ 4.00 MB ]
              USER   : 0x3A3E00000 [ 14.56 GB ]

        SRAM: 0x00020000 [ 128.00 KB ]
        DRAM: 0x40000000 [ 1.00 GB ]

        CHIP : MT6580 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000 , EVOL : 0x0000

        RNID : 95F65331D8824680BAB34D143DF4BA2

 STATUS : BLANK FLASH
 BSTYLE : EMMC FLASH BOOT

DA : USB : FULL-SPEED
DA : USB : Change Port Speed
PTFN : MediaTek DA USB VCOM (Android) (COM120)
MODE : PRELOADER PORT
PORT : 120

Boot done!

Format Ok : RESET PROTECTION

Done!
Elapsed: 00:00:31

Reconnect Power/Cable!

Tanha0321 · 12-18-2021, 18:50

Code:

Patch Level    : NRD90M
Display ID     : Android N
Ver. CodeName  : REL
Ver. Release   : 7.0
Sec. Patch     : 2019-03-01
Build Time     : 08.05.2019
Product Model  : 5049S
Product Brand  : TCL
Product Name   : 5049S
Product Device : Mickey6TVZW
Product Manfct : AlcatelOneTouch
Board Platform : mt6750
Product Info   : Mickey6TVZW

USERDATA : FILESYSTEM : EXT4  with FDE ( Full Disk Encryption *)

NVRAM : JRDSZ6750_66_TM_N_MDBIN_PCB01_MT6750_S00.MOLY_LR11_W1630_MD_MP_V16_3_P113
NVRAM : Damaged!


STORAGE : Life Status : eMMC : OK!
STORAGE : OTP Status : LOCKED!

Done!
Elapsed: 00:00:26

Operation : Reset Settings/Format FS [ v2.28 ]

Mode : SMART RESET

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MTK USB Port (COM9)
MODE : BOOTROM
PORT : 9
Waiting BOOT ack ...
BROM : Skip ACK verify
BROM : Init BROM
BROM init passed!
     CHIP : MT6755 , SBID : 0x8A00 , HWVR : 0xCB00 , SWVR : 0x0001
     TYPE : MODERN [RAPHAEL]
BROM : MEID : 587335255E62B71F19705139126CB7C6
BROM : SecLevel : 0x00000007
BROM : SecMode  : SBC+SLA+SDA
BROM : BROM|BL  : 0x05|0xFE
BROM : BOOTROM
BROM : SLA : Local Auth 
BROM : SLA : Auth Started!
BROM : SLA : Auth Passed!
BROM : SLA : 0x000000FE
BROM : PreBoot stage #1
BROM : PreBoot stage #2
AGENT : 0_base : BASE_v2112 | Manual : Disabled
AGENT : Look for suitable BootChain in DA ... 
AGENT : MTK_AllInOne_DA.bin
AGENT : Found MT6755
AGENT : MTK_DOWNLOAD_AGENT
     BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ... 
     DA : AGENT started!
DA : SYNC
     DA : MODE : BROM
DA : EXT_RAM NOT initialized!
     EMI : DEV : FireFly
     EMI : SRC : preloader_mickey6tgc.bin
     EMI : CNT : 0008
     EMI : Init EMI from INTERNAL DB
     EMI : EXT_RAM CFG Passed!
DA : BOOT to 2nd DA ...
DA : 2ND stage confirmed!
DA : SYNC with DA passed!
DA : Receiving HW info

        SRAM: 0x00038000 [ 224.00 KB ]
        DRAM: 0x80000000 [ 2.00 GB ]

        EMMC: CID : 90014A484147346132A54990E19B8539
        EMMC: VEN : HYNIX : OEM : 74 : ID : 484147346132
        EMMC: VEN : HYNIX : HAG4a2
        EMMC: SNN : 1234231707 ( 0x4990E19B) , MF : 8/2018

        EMMC: 
              BOOT1  : 0x00400000 [ 4.00 MB ]
              BOOT2  : 0x00400000 [ 4.00 MB ]
              RPMB   : 0x00400000 [ 4.00 MB ]
              USER   : 0x3AB400000 [ 14.68 GB ]

        CHIP : MT6738 , SBID : 0x8A00 , HWVR : 0xCB00 , SWVR : 0x0000 , EVOL : 0x0000

        RNID : 21C2F5434B00B430CA70733F386B6BAC

DA : USB : FULL-SPEED
DA : USB : Change Port Speed
PTFN : MediaTek DA USB VCOM (Android) (COM38)
MODE : PRELOADER PORT
PORT : 38

Boot done!

SmartInfo : 0x8F5454

Format Ok : RESET PROTECTION
Format Ok : USERDATA
Format Ok : CACHE
Format Ok : USERDATA

Done!
Elapsed: 00:00:42

Reconnect Power/Cable!

Tanha0321 · 12-18-2021, 18:51

Code:

Patch Level    : QP1A.190711.020
Display ID     : QP1A.190711.020 release-keys
Ver. CodeName  : REL
Ver. Release   : 10
Sec. Patch     : 2021-08-05
Build Time     : 11.08.2021
Product Info   : oppo6765

USERDATA : FILESYSTEM : EXT4  with FBE ( File-Base Encryption )

NVRAM : OPPO6765_20271_MDBIN_PCB01_MT6765_S00.MOLY_LR12A_R2_TC16_Q_G35_PR1_SP_V2_P204
NVRAM : 0xAA08C87A
NVRAM : State : Ok!
INFO  : WiFi MAC : 408C1F11F11F
INFO  : BlTh MAC : 408C1F11F11E


STORAGE : Life Status : eMMC : OK!
STORAGE : OTP Status : UNLOCKED!

Done!
Elapsed: 00:00:41

Operation : Reset Settings/Format FS [ v2.28 ]

Mode : SMART RESET

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MTK USB Port (COM9)
MODE : BOOTROM
PORT : 9
Waiting BOOT ack ...
BROM : Skip ACK verify
BROM : Init BROM
BROM init passed!
     CHIP : MT6765 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000
     CODE : Cervino
     TYPE : MODERN [RAPHAEL]
BROM : MEID : 61090C507830C5456A8F725BE1CF7F22
BROM : SecLevel : 0x000000E5
BROM : SecMode  : SBC+SDA+EXT
BROM : BROM|BL  : 0x05|0xFE
BROM : BOOTROM
BROM : SOCID : 4ADEADFC970B007AEA210A2278BBCB9BCF377F76112F9A559DFCDB53740B7B87
BROM : SLA : Local Auth 
BROM : SLA : Auth Started!
BROM : SLA : Auth Passed!
BROM : SLA : 0x0000001F
BROM : PreBoot stage #1
BROM : PreBoot stage #2
AGENT : 0_base : BASE_v2112 | Manual : Disabled
AGENT : Look for suitable BootChain in DA ... 
AGENT : MTK_AllInOne_DA.bin
AGENT : Found MT6765
AGENT : MTK_DOWNLOAD_AGENT
     BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ... 
     DA : AGENT started!
DA : SYNC
     DA : MODE : BROM
DA : EXT_RAM NOT initialized!
     EMI : DEV : FireFly
     EMI : SRC : preloader_oppo6765.bin
     EMI : CNT : 000B
     EMI : Init EMI from INTERNAL DB
     EMI : EXT_RAM CFG Passed!
DA : BOOT to 2nd DA ...
DA : 2ND stage confirmed!
DA : SYNC with DA passed!
DA : Receiving HW info

        SRAM: 0x0003A000 [ 232.00 KB ]
        DRAM: 0xC0000000 [ 3.00 GB ]

        EMMC: CID : 90014A68423861503E030034E440C763
        EMMC: VEN : HYNIX : OEM : 74 : ID : 68423861503E
        EMMC: VEN : HYNIX : hB8aP>
        EMMC: SNN : 3466304 ( 0x0034E440) , MF : 12/2020

        EMMC: 
              BOOT1  : 0x00400000 [ 4.00 MB ]
              BOOT2  : 0x00400000 [ 4.00 MB ]
              RPMB   : 0x01000000 [ 16.00 MB ]
              USER   : 0x747C00000 [ 29.12 GB ]

        CHIP : MT6765 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000 , EVOL : 0x0000

        RNID : 6D740B77CA642E177EC8B2F42CB923D0

DA : USB : HIGH-SPEED

Boot done!

SmartInfo : 0x825757

Format Ok : RESET PROTECTION
Format Ok : USERDATA
Format Ok : CACHE
Format Ok : USERDATA

Done!
Elapsed: 00:00:46

Reconnect Power/Cable!

Tanha0321 · 12-18-2021, 18:52

Code:

Brand     : TINNO
ProdName  : QMobile X30
ProdModel : QMobile X30
Device    : QMobile X30
AndroidVer: 4.4.2
MTKxCPU   : MT6572
MTKxPRJ   : ALPS.KK1.MP7.V1

Done!
Elapsed: 00:00:11
Reconnect Power/Cable!


Scatter Load Ok , BaseBand : MT6572 , Project : s4050ap , Storage : EMMC
Files found : 11 , Set to Flash : 10
Ready to Flash!

Operation : Flash [ v1.58 ]

======= Flash
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 15 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6572
BB_CPU_NME : [MediaTek] MT6572_S00
BB_CPU_EXT : 0xCA01 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer   : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x88
NAND Flash : NOT INSTALLED
eMMC Flash : 90014A48344732611101D777F23562F3
Initialize Memory ... 
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x90 , OEM : 014A
[eMMC] : FLASH_INF : [HYNIX] , a2G4
[eMMC] : FLASH_CID : 90014A48344732611101D777F23562F3
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00400000
[eMMC] : FLASH_LEN : 0x00000000E9000000
[eMMC] : FLASH_UCP : 3728 MiB [eMMC 4 GiB]
DEV RID    : 0xD5229C25C382E611EF76B8ECC50E699A
INT RAM    : 0x00020000
EXT RAM    : 0x20000000 [512 MiB]
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

ScatCFG : BaseBand : MT6572 , Project : s4050ap , Storage : EMMC
Setting : Flash Pre-Erase (Safe) : Enabled
Setting : AFF verify :  Disabled
Setting : HW verify :  Enabled

BL : Check HW compatibility
BL : BBID supported by BootLoader!
BL : Skip checking by User request!

BL : BatteryLevel : 3640 mV
BL : BatteryLevel Ok

BL : Flash Pre-Erase
Total blocks to Erase : 2
Erase : 0x0000000000C00000-0x0000000000100000
Erase : 0x0000000002900000-0x00000000E5E00000
Flash Pre-Erase Done, time used : 00:00:09

SecCfg Passed , 1799
BMT remark not need. Will skip

Preloader Download skipped by user request! 
PartCount : 0012
Update PMT by user request
Repartition Done!
Use FLN Mode

Processing : Flash Write
Flash now : MBR
Image Flash Ok
Flash now : EBR1
Image Flash Ok
Flash now : UBOOT
Image Flash Ok
Flash now : BOOTIMG
Image Flash Ok
Flash now : RECOVERY
Image Flash Ok
Flash now : SEC_RO
Image Flash Ok
Flash now : LOGO
Image Flash Ok
Flash now : ANDROID
Image Flash Ok
Flash now : CACHE
Image Flash Ok
Flash now : USRDATA
Image Flash Ok
Flash Write Done, time used : 00:02:52


Update Mirror PMT
Update Done!

Update RomInfo done

Done!
Elapsed: 00:03:21
Reconnect Power/Cable!

ismael05 · 12-19-2021, 04:49

can you give me the fdl file?

homer3706 · 12-19-2021, 10:50

NO NEED TESTPOINT
NO NEED BOOT KEY
JUST INSERT USB CABLE & DONE

Identify

Code:

Operation : Identify [ v2.31 ]

Mode : FLASH

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek PreLoader USB VCOM (Android) (COM5)
MODE : PRELOADER PORT
PORT : 5
Waiting BOOT ack ...
PRELOADER : ACK confirmed!
BROM : Init BROM
BROM init passed!
     CHIP : MT6765 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000
     CODE : Cervino
     TYPE : MODERN [RAPHAEL]
BROM : SecLevel : 0x00000005
BROM : SecMode  : SBC+SDA
BROM : BROM|BL  : 0xFF|0x03
BROM : PRELOADER PORT
AGENT : 0_base : BASE_v2112 | Manual : Disabled
AGENT : Look for suitable BootChain in DA ... 
AGENT : MTK_AllInOne_DA.bin
AGENT : Found MT6765
AGENT : MTK_DOWNLOAD_AGENT
     BROM : Sending 1st DA ...
     BROM : Reset Interface!
PTFN : MediaTek USB Port (COM3)
MODE : BOOTROM
PORT : 3
Waiting BOOT ack ...
BROM : Skip ACK verify
BROM : Init BROM
BROM init passed!
     CHIP : MT6765 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000
     CODE : Cervino
     TYPE : MODERN [RAPHAEL]
BROM : MEID : 71FF3C92A767131EA11BC37FFC9CBBF5
BROM : SecLevel : 0x000000E5
BROM : SecMode  : SBC+SDA+EXT
BROM : BROM|BL  : 0x05|0xFE
BROM : BOOTROM
BROM : SOCID : 8D5547DD023F2C8F0C1D67967DC346425796D345BF4EDA81BAB529F3E57FE182
BROM : SLA : Local Auth 
BROM : SLA : Starting Auth 
BROM : FF : Look for EMI
BROM : FF : EMI found!
BROM : SLA : Auth Passed!
BROM : SEC : 0x000000E0
AGENT : 0_base : BASE_v2112 | Manual : Disabled
AGENT : Look for suitable BootChain in DA ... 
AGENT : MTK_AllInOne_DA.bin
AGENT : Found MT6765
AGENT : MTK_DOWNLOAD_AGENT
     BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ... 
     DA : AGENT started!
DA : SYNC
     DA : MODE : BROM
DA : EXT_RAM NOT initialized!
     EMI : DEV : FireFly
     EMI : SRC : preloader_hs03s.bin
     EMI : CNT : 0009
     EMI : Init EMI from INTERNAL DB
     EMI : EXT_RAM CFG Passed!
DA : BOOT to 2nd DA ...
DA : 2ND stage confirmed!
DA : SYNC with DA passed!
DA : Receiving HW info

        SRAM: 0x0003A000 [ 232.00 KB ]
        DRAM: 0x100000000 [ 4.00 GB ]

        EMMC: CID : 150100525036344142006EEACA6298B1
        EMMC: VEN : SAMSUNG : OEM : 0 : ID : 525036344142
        EMMC: VEN : SAMSUNG : RP64AB
        EMMC: SNN : 1860880994 ( 0x6EEACA62) , MF : 9/2021

        EMMC: 
              BOOT1  : 0x00400000 [ 4.00 MB ]
              BOOT2  : 0x00400000 [ 4.00 MB ]
              RPMB   : 0x01000000 [ 16.00 MB ]
              USER   : 0xE8F800000 [ 58.24 GB ]

        CHIP : MT6765 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000 , EVOL : 0x0000

        RNID : D2D9383C21E1325217B6F2C3496E1A56

DA : USB : HIGH-SPEED

Boot done!

Product Brand  : samsung
Product Device : a03s
Product Model  : SM-A037F
Product Name   : a03snnxx
Patch Level    : RP1A.200720.012
Display ID     : RP1A.200720.012.A037FXXU1AUI7
Build Time     : 14.09.2021
Ver. CodeName  : REL
Ver. Release   : 11
Sec. Patch     : 2021-09-01
Product Info   : a03s
Product Board  : hs03s
Board Platform : mt6765
Product Manfct : samsung



NVRAM : TITAN_A03S_R0MP1_K65V1_64_BSP_MDBIN_PCB01_MT6765_S00.MOLY_LR12A_R3_TC10_6M_A03S_GBL_PR_SP_V1_P2
NVRAM : 0xBE0ACBD8
NVRAM : State : Ok!
INFO  : WiFi MAC : AA0036004400
INFO  : BlTh MAC : 184ECB314EF8
INFO  : IMEI[1] : 17B424303308D53
INFO  : IMEI[2] : BF8462BE2733A32


Backup sensetive data [ 16 ]
Backup path : Backup\MT6765__71FF3C92A767131EA11BC37FFC9CBBF5\
[5] Read : NVRAM
[26] Read : NVDATA
[32] Read : PROINFO
[12] Read : LK
[25] Read : NVCFG
[16] Read : PROTECT1
[17] Read : PROTECT2
[1] Read : PGPT
[37] Read : PERSIST
[0] Read : PRELOADER
[2] Read : EFS
[3] Read : SEC_EFS
[31] Read : PERSISTENT
Backup done!


STORAGE : Life Status : eMMC : OK!
STORAGE : OTP Status : NOT Enabled!

PRELOADER : DEVICE : 
 DEV : MT6765
 NME : preloader_hs03s.bin
 CNT : 0009
 EMI : [00] : eMMC : DDR3 : ID : 90014A484247346132 : VEN : HYNIX     | DEV : HBG4a2 : RAM : [ 3.00 GB ]
 EMI : [01] : eMMC : DDR3 : ID : 90014A68423861503E : VEN : HYNIX     | DEV : hB8aP> : RAM : [ 3.00 GB ]
 EMI : [02] : eMMC : DDR3 : ID : 90014A484147346132 : VEN : HYNIX     | DEV : HAG4a2 : RAM : [ 2.00 GB ]
 EMI : [03] : eMMC : DDR3 : ID : 150100475836424142 : VEN : SAMSUNG   | DEV : GX6BAB : RAM : [ 3.00 GB ]
 EMI : [04] : eMMC : DDR3 : ID : 150100475836424D42 : VEN : SAMSUNG   | DEV : GX6BMB : RAM : [ 3.00 GB ]
 EMI : [05] : eMMC : DDR3 : ID : 150100514436334D42 : VEN : SAMSUNG   | DEV : QD63MB : RAM : [ 2.00 GB ]
 EMI : [06] : eMMC : DDR3 : ID : 150100515836334D42 : VEN : SAMSUNG   | DEV : QX63MB : RAM : [ 2.00 GB ]
 EMI : [07] : eMMC : DDR3 : ID : 150100525036344D42 : VEN : SAMSUNG   | DEV : RP64MB : RAM : [ 4.00 GB ]
 EMI : [08] : eMMC : DDR3 : ID : 150100525036344142 : VEN : SAMSUNG   | DEV : RP64AB : RAM : [ 4.00 GB ]
PRELOADER saved to : Backup\PRELOADER\preloader_hs03s.bin

Done!
Elapsed: 00:00:47

Smart Reset Extra

Code:

Operation : Reset Settings/Format FS [ v2.31 ]

Mode : SMART RESET EXTRA

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek PreLoader USB VCOM (Android) (COM5)
MODE : PRELOADER PORT
PORT : 5
Waiting BOOT ack ...
PRELOADER : ACK confirmed!
BROM : Init BROM
BROM init passed!
     CHIP : MT6765 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000
     CODE : Cervino
     TYPE : MODERN [RAPHAEL]
BROM : SecLevel : 0x00000005
BROM : SecMode  : SBC+SDA
BROM : BROM|BL  : 0xFF|0x03
BROM : PRELOADER PORT
AGENT : 0_base : BASE_v2112 | Manual : Disabled
AGENT : Look for suitable BootChain in DA ... 
AGENT : MTK_AllInOne_DA.bin
AGENT : Found MT6765
AGENT : MTK_DOWNLOAD_AGENT
     BROM : Sending 1st DA ...
     BROM : Reset Interface!
PTFN : MediaTek USB Port (COM3)
MODE : BOOTROM
PORT : 3
Waiting BOOT ack ...
BROM : Skip ACK verify
BROM : Init BROM
BROM init passed!
     CHIP : MT6765 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000
     CODE : Cervino
     TYPE : MODERN [RAPHAEL]
BROM : MEID : 71FF3C92A767131EA11BC37FFC9CBBF5
BROM : SecLevel : 0x000000E5
BROM : SecMode  : SBC+SDA+EXT
BROM : BROM|BL  : 0x05|0xFE
BROM : BOOTROM
BROM : SOCID : 8D5547DD023F2C8F0C1D67967DC346425796D345BF4EDA81BAB529F3E57FE182
BROM : SLA : Local Auth 
BROM : SLA : Starting Auth 
BROM : SLA : Auth Passed!
BROM : SEC : 0x000000E0
AGENT : 0_base : BASE_v2112 | Manual : Disabled
AGENT : Look for suitable BootChain in DA ... 
AGENT : MTK_AllInOne_DA.bin
AGENT : Found MT6765
AGENT : MTK_DOWNLOAD_AGENT
     BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ... 
     DA : AGENT started!
DA : SYNC
     DA : MODE : BROM
DA : EXT_RAM NOT initialized!
     EMI : DEV : FireFly
     EMI : SRC : preloader_hs03s.bin
     EMI : CNT : 0009
     EMI : Init EMI from INTERNAL DB
     EMI : EXT_RAM CFG Passed!
DA : BOOT to 2nd DA ...
DA : 2ND stage confirmed!
DA : SYNC with DA passed!
DA : Receiving HW info

        SRAM: 0x0003A000 [ 232.00 KB ]
        DRAM: 0x100000000 [ 4.00 GB ]

        EMMC: CID : 150100525036344142006EEACA6298B1
        EMMC: VEN : SAMSUNG : OEM : 0 : ID : 525036344142
        EMMC: VEN : SAMSUNG : RP64AB
        EMMC: SNN : 1860880994 ( 0x6EEACA62) , MF : 9/2021

        EMMC: 
              BOOT1  : 0x00400000 [ 4.00 MB ]
              BOOT2  : 0x00400000 [ 4.00 MB ]
              RPMB   : 0x01000000 [ 16.00 MB ]
              USER   : 0xE8F800000 [ 58.24 GB ]

        CHIP : MT6765 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000 , EVOL : 0x0000

        RNID : D2D9383C21E1325217B6F2C3496E1A56

DA : USB : HIGH-SPEED

Boot done!

SmartInfo : 0x835757

Format Ok : RESET PROTECTION
Format Ok : USERDATA
Format Ok : CACHE
Format Ok : USERDATA
Format Ok : USERDATA
Format Ok : Vendor Extra

Done!
Elapsed: 00:00:31

Reconnect Power/Cable!

A.G.Shahid · 12-19-2021, 12:03

Card found : 73CA70CC , v0151
Infinity-Box Chinese Miracle II : SC/RDA Module [SCR] v1.07

SCRD mode : AUTO
SPRD mode : SC6530 : REV : 0000 : NOR : [ 4MB-8MB ]

Operation : Format FileSystem [ v1.07 ]

1. Power off device
2. Not hold any key on device!
3. Insert cable and battery in device!

Wait for device ...

Device Connected!
Enter SVC ...
Waiting Device ...
Check SVC ...
SVC : DiagChannel opened!

Boot Done!

Format FFS Done!

Done!
Elapsed: 00:00:20

Reconnect Power/Cable!

A.G.Shahid · 12-19-2021, 12:05

Card found : 73CA70CC , v0151
Infinity-Box Chinese Miracle II : SC/RDA Module [SCR] v1.07

SCRD mode : AUTO
SPRD mode : SC6530 : REV : 0000 : NOR : [ 4MB-8MB ]

SPRD mode : SC6531 : REV : 0000 : NOR : [ 8MB-16MB]

Operation : Format FileSystem [ v1.07 ]

1. Power off device
2. Press and hold BootKey or use BootCable
3. Insert cable and battery in device!

Wait for device ...

Device Connected!
BootVersion : SPRD3
BootSource : InternalLibrary
BootVersion : Infinity SCR 653x NOR v1.3(c)2019
Port speed : 921600
FDL Flash : Control transfered!

Boot Done!

CS0_MEM : SPI : [GIGADEVICE] : GD25Q32 : 0x00400000 [ 4MiB ]

Make backup of sensetive data
Backup saved to : C:\InfinityBox\CM2SCR\Backup\00400000_FMT_BACK_016 859629F37_NVM.nv

Executing FormatFFS ...
Format FFS Done!

Done!
Elapsed: 00:00:27

Reconnect Power/Cable!

A.G.Shahid · 12-19-2021, 12:08

Card found : 73CA70CC , v0151
Infinity-Box Chinese Miracle II : SC/RDA Module [SCR] v1.07

SCRD mode : AUTO
SPRD mode : SC6530 : REV : 0000 : NOR : [ 4MB-8MB ]

Operation : Identify [ v1.07 ]
BootMode : SVC

1. Power off device
2. Not hold any key on device!
3. Insert cable and battery in device!

Wait for device ...

Device Connected!
Enter SVC ...
Waiting Device ...
Check SVC ...
SVC : DiagChannel opened!

Boot Done!

SOC GEN : SPRD ( Legacy )
ModemInfo :
Project Version: SC6531EFM_BAR
BASE Version: BASE_SVN
HW Version: SC6531EFM_BAR
CMP_Time : 12-22-2020 10:52:56

SecInfo :
IMEI[1] : 357921570482865
IMEI[2] : 357921575482860
IMEI[3] : 000000000000000
WIFIMAC : FFFFFFFFFFFF
BT_MAC : 640805002251
SEC_ID : 9E9DFFFFC2D263DD

Done!
Elapsed: 00:00:13

Reconnect Power/Cable!

Operation : Format FileSystem [ v1.07 ]

1. Power off device
2. Not hold any key on device!
3. Insert cable and battery in device!

Wait for device ...

Device Connected!
Enter SVC ...
Waiting Device ...
Check SVC ...
SVC : DiagChannel opened!

Boot Done!

Format FFS Done!

Done!
Elapsed: 00:00:20

Reconnect Power/Cable!

A.G.Shahid · 12-19-2021, 12:09

Card found : 73CA70CC , v0151
Infinity-Box [ Chinese Miracle ] MediaTek Service Module [ MTK ] v2.31

Load IDBase v1121431 Ok!

Update configuration ...
Load IDBase v1121431 Ok!

Operation : Reset Settings/Format FS [ v2.31 ]

Mode : SMART RESET

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek USB Port (COM16)
MODE : BOOTROM
PORT : 16
Waiting BOOT ack ...
BROM : Skip ACK verify
BROM : Init BROM
BROM init passed!
CHIP : MT6768 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000
CODE : Talbot
TYPE : MODERN [RAPHAEL]
BROM : MEID : DB25E2AE7982BE035034A921F36A11AC
BROM : SecLevel : 0x000000E5
BROM : SecMode : SBC+SDA+EXT
BROM : BROM|BL : 0x05|0xFE
BROM : BOOTROM
BROM : SOCID : FD980DA6AA60B3066A27CDB8CE03337AF53F000C7B3A22A3D8 E8B9CD9D233C8C
BROM : SLA : Local Auth
BROM : SLA : Starting Auth
BROM : FF : Look for EMI
BROM : FF : EMI found!
BROM : SLA : Auth Passed!
BROM : SEC : 0x000000E0
AGENT : 0_base : BASE_v2112 | Manual : Disabled
AGENT : Look for suitable BootChain in DA ...
AGENT : MTK_AllInOne_DA.bin
AGENT : Found MT6768
AGENT : MTK_DOWNLOAD_AGENT
BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ...
DA : AGENT started!
DA : SYNC
DA : MODE : BROM
DA : EXT_RAM NOT initialized!
EMI : DEV : FireFly
EMI : SRC : preloader_k68v1_64.bin
EMI : CNT : 000B
EMI : Init EMI from INTERNAL DB
EMI : EXT_RAM CFG Passed!
DA : BOOT to 2nd DA ...
DA : 2ND stage confirmed!
DA : SYNC with DA passed!
DA : Receiving HW info

SRAM: 0x00070000 [ 448.00 KB ]
DRAM: 0x100000000 [ 4.00 GB ]

EMMC: CID : 150100445636444D4202AFAC903AB675
EMMC: VEN : SAMSUNG : OEM : 0 : ID : 445636444D42
EMMC: VEN : SAMSUNG : DV6DMB
EMMC: SNN : 2947321914 ( 0xAFAC903A) , MF : 11/2019

EMMC:
BOOT1 : 0x00400000 [ 4.00 MB ]
BOOT2 : 0x00400000 [ 4.00 MB ]
RPMB : 0x01000000 [ 16.00 MB ]
USER : 0x1D1EC00000 [ 116.48 GB ]

CHIP : MT6768 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0001 , EVOL : 0x0000

RNID : 956D0774FA7253AA9044AD4FDE6D4464

DA : USB : HIGH-SPEED

Boot done!

SmartInfo : 0x835757

Format Ok : RESET PROTECTION
Format Ok : USERDATA
Format Ok : CACHE
Format Ok : USERDATA

Done!
Elapsed: 00:00:38

Reconnect Power/Cable!

A.G.Shahid · 12-19-2021, 12:10

Card found : 73CA70CC , v0151
Infinity-Box [ Chinese Miracle ] MediaTek Service Module [ MTK ] v2.31

Load IDBase v1121431 Ok!

Update configuration ...
Load IDBase v1121431 Ok!

Operation : Reset Settings/Format FS [ v2.31 ]

Mode : FRP [ RESET PROTECTION ]

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek USB Port (COM16)
MODE : BOOTROM
PORT : 16
Waiting BOOT ack ...
BROM : Skip ACK verify
BROM : Init BROM
BROM init passed!
CHIP : MT6779 , SBID : 0x8A00 , HWVR : 0xCA01 , SWVR : 0x0000
CODE : Lafite
TYPE : MODERN [RAPHAEL]
BROM : MEID : 713C7658519936797342219F5A2A14C7
BROM : SecLevel : 0x000000E5
BROM : SecMode : SBC+SDA+EXT
BROM : BROM|BL : 0x05|0xFE
BROM : BOOTROM
BROM : SOCID : 3E48093967EBA62152DCBCC398C88449D7BA0356D3D396A818 C0716B66C8C291
BROM : SLA : Local Auth
BROM : SLA : Starting Auth
BROM : SLA : Auth Passed!
BROM : SEC : 0x000000E0
AGENT : 0_base : BASE_v2112 | Manual : Disabled
AGENT : Look for suitable BootChain in DA ...
AGENT : MTK_AllInOne_DA.bin
AGENT : Found MT6779
AGENT : MTK_DOWNLOAD_AGENT
BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ...
DA : AGENT started!
DA : SYNC
DA : MODE : BROM
DA : EXT_RAM NOT initialized!
EMI : DEV : INFINITY
EMI : SRC : PRELOADER_INFINITY_0
EMI : CNT : 0001
EMI : Init EMI from INTERNAL DB
EMI : EXT_RAM CFG Passed!
DA : BOOT to 2nd DA ...
DA : 2ND stage confirmed!
DA : SYNC with DA passed!
DA : Receiving HW info

SRAM: 0x00080000 [ 512.00 KB ]
DRAM: 0x200000000 [ 8.00 GB ]

UFS: CE014B4D3856383030314A4D2D423831
UFS:
VEN : 0x01CE
VID : KM8V8001JM-B81
IFW : 1000
LU0 : 0x00400000 [ 4.00 MB ]
LU1 : 0x00400000 [ 4.00 MB ]
LU2 : 0x1DCB000000 [ 119.17 GB ]
FSN : 3cfbea00640d
REG : 0x101010000

CHIP : MT6779 , SBID : 0x8A00 , HWVR : 0xCA01 , SWVR : 0x0000 , EVOL : 0x0000

RNID : DFE7542C67CC90B9C731E551D84CABC6

DA : USB : HIGH-SPEED

Boot done!

Format Ok : RESET PROTECTION

Done!
Elapsed: 00:00:20

profkefah · 12-19-2021, 14:24

ORIGINAL POSTER
LYON GEM FLASH

SOLUTION WAS READ BACKUP
THEN WIPE SELECTED FILES
THEN WRITE BACKUP
FLASHING WAS USELESS

tayobjoy1 · 12-19-2021, 14:46

Code:

Card found : 46828B86 , v0151
Infinity-Box [ Chinese Miracle ] MediaTek Service Module [ MTK ] v2.31

Load IDBase v1121431 Ok!

Update configuration ... 
Load IDBase v1121431 Ok!

Operation : Identify [ v2.31 ]

Mode : FLASH

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek USB Port (COM12)
MODE : BOOTROM
PORT : 12
Waiting BOOT ack ...
BROM : Skip ACK verify
BROM : Init BROM
BROM init passed!
     CHIP : MT6580 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000
     TYPE : LEGACY [MTK]
BROM : MEID : E0EAF9A69959448FC2DB095FAFD88BE2
BROM : SecLevel : 0x00000000
BROM : SecMode  : PLAIN
BROM : BROM|BL  : 0x05|0xFE
BROM : BOOTROM
BROM : EMI : Search
BROM : EMI : Found!
AGENT : 0_base : BASE_v2112 | Manual : Disabled
AGENT : Look for suitable BootChain in DA ... 
AGENT : MTK_AllInOne_DA.bin
AGENT : Found MT6580
AGENT : MTK_DOWNLOAD_AGENT
     BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ... 
     DA : AGENT started!
NAND : DEVICE NOT FOUND
NAND : 000000000000000000000000
eMMC : OK
eMMC : 460001154D3236453720034243555AD6
DAInf: 4 : 2 : 156
DA : EXT_RAM NOT initialized!
eMMC : OK
eMMC : 150100464536324D42032037D65A5543
NAND : DEVICE NOT FOUND
NAND : 000000000000000000000000
DRAM : 0x0178
     EMI : DEV : FireFly
     EMI : SRC : preloader_rlk6580_weg_n.bin
     EMI : CNT : 0008
     EMI : [00] : ID : 150100463832324D42 : VEN : SAMSUNG   | DEV : F822MB : RAM : [ 1,00 GB ]
     EMI : [01] : ID : 700100454841434538 : VEN : KINGSTON  | DEV : EHACE8 : RAM : [ 1,00 GB ]
     EMI : [02] : ID : 150100464531324D42 : VEN : SAMSUNG   | DEV : FE12MB : RAM : [ 1,00 GB ]
     EMI : [03] : ID : 700100454841454538 : VEN : KINGSTON  | DEV : EHAEE8 : RAM : [ 1,00 GB ]
     EMI : [04] : ID : 150100464536324D42 : VEN : SAMSUNG   | DEV : FE62MB : RAM : [ 1,00 GB ]
     EMI : [05] : ID : 150100514536334D42 : VEN : SAMSUNG   | DEV : QE63MB : RAM : [ 2,00 GB ]
     EMI : [06] : ID : 150100514531334D42 : VEN : SAMSUNG   | DEV : QE13MB : RAM : [ 2,00 GB ]
     EMI : [07] : ID : 700100454841434541 : VEN : KINGSTON  | DEV : EHACEA : RAM : [ 2,00 GB ]
     EMI : Init EMI from PRELOADER
INIT : 0xBC : DRAM [ 0x00000000 :  [ 0 B ] ]
DRAM : DRAM: 0x40000000 [ 1,00 GB ]
     DA : DRAM ready!
DA : BOOT to 2nd DA ...
DA : Receiving HW info

        EMMC: CID : 150100464536324D42032037D65A5543
        EMMC: VEN : SAMSUNG : OEM : 0 : ID : 464536324D42
        EMMC: VEN : SAMSUNG : FE62MB
        EMMC: SNN : 540530266 ( 0x2037D65A) , MF : 5/2018

        EMMC: 
              BOOT1  : 0x00400000 [ 4,00 MB ]
              BOOT2  : 0x00400000 [ 4,00 MB ]
              RPMB   : 0x00400000 [ 4,00 MB ]
              USER   : 0x3A3E00000 [ 14,56 GB ]

        SRAM: 0x00020000 [ 128,00 KB ]
        DRAM: 0x40000000 [ 1,00 GB ]

        CHIP : MT6580 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000 , EVOL : 0x0000

        RNID : 9E9A5058CBD28BC85DD694173077F90A

 STATUS : BLANK FLASH
 BSTYLE : EMMC FLASH BOOT

DA : USB : FULL-SPEED
DA : USB : Change Port Speed
PTFN : MediaTek DA USB VCOM (Android) (COM20)
MODE : PRELOADER PORT
PORT : 20

Boot done!

Patch Level    : NRD90M
Display ID     : K7-H8019A-N-180124V180
Ver. CodeName  : REL
Ver. Release   : 7.0
Sec. Patch     : 2017-12-05
Build Time     : 24.01.2018
Product Model  : TECNO K7
Product Brand  : TECNO
Product Name   : H8019
Product Device : TECNO-K7
Product Manfct : TECNO
Board Platform : mt6580
Product Info   : rlk6580_weg_n

USERDATA : FILESYSTEM : EXT4  with FDE ( Full Disk Encryption ***)

NVRAM : 0x75029322
NVRAM : State : Ok!
INFO  : WiFi MAC : 709FA964A5E5
INFO  : BlTh MAC : 709FA9646B4D
INFO  : IMEI[1] : 358874091503843
INFO  : IMEI[2] : 358874091503850


Backup sensetive data [ 16 ]
Backup path : Backup\MT6580__E0EAF9A69959448FC2DB095FAFD88BE2\
[3] Read : NVRAM
[14] Read : NVDATA
[2] Read : PROINFO
[7] Read : LK
[4] Read : PROTECT1
[5] Read : PROTECT2
[0] Read : PRELOADER
Backup done!


Done!
Elapsed: 00:00:33

Code:

Operation : Reset Settings/Format FS [ v2.31 ]

Mode : FRP [ RESET PROTECTION ]

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek USB Port (COM12)
MODE : BOOTROM
PORT : 12
Waiting BOOT ack ...
BROM : Skip ACK verify
BROM : Init BROM
BROM init passed!
     CHIP : MT6580 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000
     TYPE : LEGACY [MTK]
BROM : MEID : E0EAF9A69959448FC2DB095FAFD88BE2
BROM : SecLevel : 0x00000000
BROM : SecMode  : PLAIN
BROM : BROM|BL  : 0x05|0xFE
BROM : BOOTROM
AGENT : 0_base : BASE_v2112 | Manual : Disabled
AGENT : Look for suitable BootChain in DA ... 
AGENT : MTK_AllInOne_DA.bin
AGENT : Found MT6580
AGENT : MTK_DOWNLOAD_AGENT
     BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ... 
     DA : AGENT started!
NAND : DEVICE NOT FOUND
NAND : 000000000000000000000000
eMMC : OK
eMMC : 460001154D3236453720034243555AD6
DAInf: 4 : 2 : 156
DA : EXT_RAM NOT initialized!
eMMC : OK
eMMC : 150100464536324D42032037D65A5543
NAND : DEVICE NOT FOUND
NAND : 000000000000000000000000
DRAM : 0x0178
     EMI : DEV : FireFly
     EMI : SRC : preloader_rlk6580_weg_n.bin
     EMI : CNT : 0008
     EMI : [00] : ID : 150100463832324D42 : VEN : SAMSUNG   | DEV : F822MB : RAM : [ 1,00 GB ]
     EMI : [01] : ID : 700100454841434538 : VEN : KINGSTON  | DEV : EHACE8 : RAM : [ 1,00 GB ]
     EMI : [02] : ID : 150100464531324D42 : VEN : SAMSUNG   | DEV : FE12MB : RAM : [ 1,00 GB ]
     EMI : [03] : ID : 700100454841454538 : VEN : KINGSTON  | DEV : EHAEE8 : RAM : [ 1,00 GB ]
     EMI : [04] : ID : 150100464536324D42 : VEN : SAMSUNG   | DEV : FE62MB : RAM : [ 1,00 GB ]
     EMI : [05] : ID : 150100514536334D42 : VEN : SAMSUNG   | DEV : QE63MB : RAM : [ 2,00 GB ]
     EMI : [06] : ID : 150100514531334D42 : VEN : SAMSUNG   | DEV : QE13MB : RAM : [ 2,00 GB ]
     EMI : [07] : ID : 700100454841434541 : VEN : KINGSTON  | DEV : EHACEA : RAM : [ 2,00 GB ]
     EMI : Init EMI from PRELOADER
INIT : 0xBC : DRAM [ 0x00000000 :  [ 0 B ] ]
DRAM : DRAM: 0x40000000 [ 1,00 GB ]
     DA : DRAM ready!
DA : BOOT to 2nd DA ...
DA : Receiving HW info

        EMMC: CID : 150100464536324D42032037D65A5543
        EMMC: VEN : SAMSUNG : OEM : 0 : ID : 464536324D42
        EMMC: VEN : SAMSUNG : FE62MB
        EMMC: SNN : 540530266 ( 0x2037D65A) , MF : 5/2018

        EMMC: 
              BOOT1  : 0x00400000 [ 4,00 MB ]
              BOOT2  : 0x00400000 [ 4,00 MB ]
              RPMB   : 0x00400000 [ 4,00 MB ]
              USER   : 0x3A3E00000 [ 14,56 GB ]

        SRAM: 0x00020000 [ 128,00 KB ]
        DRAM: 0x40000000 [ 1,00 GB ]

        CHIP : MT6580 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000 , EVOL : 0x0000

        RNID : 9E9A5058CBD28BC85DD694173077F90A

 STATUS : BLANK FLASH
 BSTYLE : EMMC FLASH BOOT

DA : USB : FULL-SPEED
DA : USB : Change Port Speed
PTFN : MediaTek DA USB VCOM (Android) (COM20)
MODE : PRELOADER PORT
PORT : 20

Boot done!

Format Ok : RESET PROTECTION

Done!
Elapsed: 00:00:15

Reconnect Power/Cable!

12-19-2021, 12:03	#69024 (permalink)
A.G.Shahid No Life Poster Join Date: Nov 2016 Location: ISI Posts: 5,792 Member: 2644066 Status: Offline Thanks Meter: 1,773	Call me c12 reset password done by cm2 with out boot key Card found : 73CA70CC , v0151 Infinity-Box Chinese Miracle II : SC/RDA Module [SCR] v1.07 SCRD mode : AUTO SPRD mode : SC6530 : REV : 0000 : NOR : [ 4MB-8MB ] Operation : Format FileSystem [ v1.07 ] 1. Power off device 2. Not hold any key on device! 3. Insert cable and battery in device! Wait for device ... Device Connected! Enter SVC ... Waiting Device ... Check SVC ... SVC : DiagChannel opened! Boot Done! Format FFS Done! Done! Elapsed: 00:00:20 Reconnect Power/Cable!

12-19-2021, 12:05	#69025 (permalink)
A.G.Shahid No Life Poster Join Date: Nov 2016 Location: ISI Posts: 5,792 Member: 2644066 Status: Offline Thanks Meter: 1,773	Qmobile l2 reset password done by cm2 Card found : 73CA70CC , v0151 Infinity-Box Chinese Miracle II : SC/RDA Module [SCR] v1.07 SCRD mode : AUTO SPRD mode : SC6530 : REV : 0000 : NOR : [ 4MB-8MB ] SPRD mode : SC6531 : REV : 0000 : NOR : [ 8MB-16MB] Operation : Format FileSystem [ v1.07 ] 1. Power off device 2. Press and hold BootKey or use BootCable 3. Insert cable and battery in device! Wait for device ... Device Connected! BootVersion : SPRD3 BootSource : InternalLibrary BootVersion : Infinity SCR 653x NOR v1.3(c)2019 Port speed : 921600 FDL Flash : Control transfered! Boot Done! CS0_MEM : SPI : [GIGADEVICE] : GD25Q32 : 0x00400000 [ 4MiB ] Make backup of sensetive data Backup saved to : C:\InfinityBox\CM2SCR\Backup\00400000_FMT_BACK_016 859629F37_NVM.nv Executing FormatFFS ... Format FFS Done! Done! Elapsed: 00:00:27 Reconnect Power/Cable!

12-19-2021, 12:08	#69026 (permalink)
A.G.Shahid No Life Poster Join Date: Nov 2016 Location: ISI Posts: 5,792 Member: 2644066 Status: Offline Thanks Meter: 1,773	E tachi b786 reset password done by cm2 Card found : 73CA70CC , v0151 Infinity-Box Chinese Miracle II : SC/RDA Module [SCR] v1.07 SCRD mode : AUTO SPRD mode : SC6530 : REV : 0000 : NOR : [ 4MB-8MB ] Operation : Identify [ v1.07 ] BootMode : SVC 1. Power off device 2. Not hold any key on device! 3. Insert cable and battery in device! Wait for device ... Device Connected! Enter SVC ... Waiting Device ... Check SVC ... SVC : DiagChannel opened! Boot Done! SOC GEN : SPRD ( Legacy ) ModemInfo : Project Version: SC6531EFM_BAR BASE Version: BASE_SVN HW Version: SC6531EFM_BAR CMP_Time : 12-22-2020 10:52:56 SecInfo : IMEI[1] : 357921570482865 IMEI[2] : 357921575482860 IMEI[3] : 000000000000000 WIFIMAC : FFFFFFFFFFFF BT_MAC : 640805002251 SEC_ID : 9E9DFFFFC2D263DD Done! Elapsed: 00:00:13 Reconnect Power/Cable! Operation : Format FileSystem [ v1.07 ] 1. Power off device 2. Not hold any key on device! 3. Insert cable and battery in device! Wait for device ... Device Connected! Enter SVC ... Waiting Device ... Check SVC ... SVC : DiagChannel opened! Boot Done! Format FFS Done! Done! Elapsed: 00:00:20 Reconnect Power/Cable!

12-19-2021, 12:09	#69027 (permalink)
A.G.Shahid No Life Poster Join Date: Nov 2016 Location: ISI Posts: 5,792 Member: 2644066 Status: Offline Thanks Meter: 1,773	Vivo s1 remove frp done by cm2 Card found : 73CA70CC , v0151 Infinity-Box [ Chinese Miracle ] MediaTek Service Module [ MTK ] v2.31 Load IDBase v1121431 Ok! Update configuration ... Load IDBase v1121431 Ok! Operation : Reset Settings/Format FS [ v2.31 ] Mode : SMART RESET 1. Make sure device is powered off. Power off, if need. Wait 20 seconds after 2. Insert USB cable in phone Waiting for device connection ... PTFN : MediaTek USB Port (COM16) MODE : BOOTROM PORT : 16 Waiting BOOT ack ... BROM : Skip ACK verify BROM : Init BROM BROM init passed! CHIP : MT6768 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000 CODE : Talbot TYPE : MODERN [RAPHAEL] BROM : MEID : DB25E2AE7982BE035034A921F36A11AC BROM : SecLevel : 0x000000E5 BROM : SecMode : SBC+SDA+EXT BROM : BROM\|BL : 0x05\|0xFE BROM : BOOTROM BROM : SOCID : FD980DA6AA60B3066A27CDB8CE03337AF53F000C7B3A22A3D8 E8B9CD9D233C8C BROM : SLA : Local Auth BROM : SLA : Starting Auth BROM : FF : Look for EMI BROM : FF : EMI found! BROM : SLA : Auth Passed! BROM : SEC : 0x000000E0 AGENT : 0_base : BASE_v2112 \| Manual : Disabled AGENT : Look for suitable BootChain in DA ... AGENT : MTK_AllInOne_DA.bin AGENT : Found MT6768 AGENT : MTK_DOWNLOAD_AGENT BROM : Sending 1st DA ... BROM : DA sent BROM :Transfer control to DA ... DA : AGENT started! DA : SYNC DA : MODE : BROM DA : EXT_RAM NOT initialized! EMI : DEV : FireFly EMI : SRC : preloader_k68v1_64.bin EMI : CNT : 000B EMI : Init EMI from INTERNAL DB EMI : EXT_RAM CFG Passed! DA : BOOT to 2nd DA ... DA : 2ND stage confirmed! DA : SYNC with DA passed! DA : Receiving HW info SRAM: 0x00070000 [ 448.00 KB ] DRAM: 0x100000000 [ 4.00 GB ] EMMC: CID : 150100445636444D4202AFAC903AB675 EMMC: VEN : SAMSUNG : OEM : 0 : ID : 445636444D42 EMMC: VEN : SAMSUNG : DV6DMB EMMC: SNN : 2947321914 ( 0xAFAC903A) , MF : 11/2019 EMMC: BOOT1 : 0x00400000 [ 4.00 MB ] BOOT2 : 0x00400000 [ 4.00 MB ] RPMB : 0x01000000 [ 16.00 MB ] USER : 0x1D1EC00000 [ 116.48 GB ] CHIP : MT6768 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0001 , EVOL : 0x0000 RNID : 956D0774FA7253AA9044AD4FDE6D4464 DA : USB : HIGH-SPEED Boot done! SmartInfo : 0x835757 Format Ok : RESET PROTECTION Format Ok : USERDATA Format Ok : CACHE Format Ok : USERDATA Done! Elapsed: 00:00:38 Reconnect Power/Cable!

12-19-2021, 12:10	#69028 (permalink)
A.G.Shahid No Life Poster Join Date: Nov 2016 Location: ISI Posts: 5,792 Member: 2644066 Status: Offline Thanks Meter: 1,773	Oppo reno 3 cph 2043 reset frf done by cm2 Card found : 73CA70CC , v0151 Infinity-Box [ Chinese Miracle ] MediaTek Service Module [ MTK ] v2.31 Load IDBase v1121431 Ok! Update configuration ... Load IDBase v1121431 Ok! Operation : Reset Settings/Format FS [ v2.31 ] Mode : FRP [ RESET PROTECTION ] 1. Make sure device is powered off. Power off, if need. Wait 20 seconds after 2. Insert USB cable in phone Waiting for device connection ... PTFN : MediaTek USB Port (COM16) MODE : BOOTROM PORT : 16 Waiting BOOT ack ... BROM : Skip ACK verify BROM : Init BROM BROM init passed! CHIP : MT6779 , SBID : 0x8A00 , HWVR : 0xCA01 , SWVR : 0x0000 CODE : Lafite TYPE : MODERN [RAPHAEL] BROM : MEID : 713C7658519936797342219F5A2A14C7 BROM : SecLevel : 0x000000E5 BROM : SecMode : SBC+SDA+EXT BROM : BROM\|BL : 0x05\|0xFE BROM : BOOTROM BROM : SOCID : 3E48093967EBA62152DCBCC398C88449D7BA0356D3D396A818 C0716B66C8C291 BROM : SLA : Local Auth BROM : SLA : Starting Auth BROM : SLA : Auth Passed! BROM : SEC : 0x000000E0 AGENT : 0_base : BASE_v2112 \| Manual : Disabled AGENT : Look for suitable BootChain in DA ... AGENT : MTK_AllInOne_DA.bin AGENT : Found MT6779 AGENT : MTK_DOWNLOAD_AGENT BROM : Sending 1st DA ... BROM : DA sent BROM :Transfer control to DA ... DA : AGENT started! DA : SYNC DA : MODE : BROM DA : EXT_RAM NOT initialized! EMI : DEV : INFINITY EMI : SRC : PRELOADER_INFINITY_0 EMI : CNT : 0001 EMI : Init EMI from INTERNAL DB EMI : EXT_RAM CFG Passed! DA : BOOT to 2nd DA ... DA : 2ND stage confirmed! DA : SYNC with DA passed! DA : Receiving HW info SRAM: 0x00080000 [ 512.00 KB ] DRAM: 0x200000000 [ 8.00 GB ] UFS: CE014B4D3856383030314A4D2D423831 UFS: VEN : 0x01CE VID : KM8V8001JM-B81 IFW : 1000 LU0 : 0x00400000 [ 4.00 MB ] LU1 : 0x00400000 [ 4.00 MB ] LU2 : 0x1DCB000000 [ 119.17 GB ] FSN : 3cfbea00640d REG : 0x101010000 CHIP : MT6779 , SBID : 0x8A00 , HWVR : 0xCA01 , SWVR : 0x0000 , EVOL : 0x0000 RNID : DFE7542C67CC90B9C731E551D84CABC6 DA : USB : HIGH-SPEED Boot done! Format Ok : RESET PROTECTION Done! Elapsed: 00:00:20

12-19-2021, 04:49	#69022 (permalink)
ismael05 Junior Member Join Date: Dec 2019 Location: Philippines Posts: 2 Member: 2941030 Status: Offline Thanks Meter: 0	can you give me the fdl file?

12-19-2021, 14:24	#69029 (permalink)
profkefah No Life Poster Join Date: Mar 2015 Location: Islam Age: 35 Posts: 7,401 Member: 2371500 Status: Offline Thanks Meter: 5,804	SAMSUNG A226B A225G stuck on logo after unlock bootloader fix done with CM2 ORIGINAL POSTER LYON GEM FLASH SOLUTION WAS READ BACKUP THEN WIPE SELECTED FILES THEN WRITE BACKUP FLASHING WAS USELESS

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Unlocking 5190	Ryu	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	23	01-07-2018 17:14
news headlines to gsm phone	mos	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	7	05-22-2016 11:42
my 8810 is phone locked ,can somebody please help	duyphuc	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	18	12-23-2014 09:03
need software for 5161 by cable	mln2000	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	6	08-29-2010 20:17