Successfully unlocked/repaired phones by Infinity-Box - Page 4248 - GSM-Forum

A.G.Shahid · 07-11-2020, 06:30

Card found : 73CA70CC , v0144
Infinity-Box Chinese Miracle II : SC/RDA Module [SCR] v1.06

SCRD mode : AUTO
SPRD mode : SC6530 : REV : 0000 : NOR : [ 4MB-8MB ]

Operation : Identify [ v1.06 ]
BootMode : SVC

1. Power off device
2. Not hold any key on device!
3. Insert cable and battery in device!

Wait for device ...

Device Connected!
Enter SVC ...
Waiting Device ...
Check SVC ...
SVC : DiagChannel opened!

Boot Done!

SOC GEN : SPRD ( Legacy )
ModemInfo :
Project Version: SC6531EFM_BAR
BASE Version: BASE_SVN
HW Version: SC6531EFM_BAR
CMP_Time : 01-15-2020 11:04:51

SecInfo :
IMEI[1] :
IMEI[2] :
IMEI[3] :
WIFIMAC : FFFFFFFFFFFF
BT_MAC : 018321094528
SEC_ID : 7B9EFFFF39A561D3

Done!
Elapsed: 00:00:20

Reconnect Power/Cable!

Operation : Format FileSystem [ v1.06 ]

1. Power off device
2. Not hold any key on device!
3. Insert cable and battery in device!

Wait for device ...

Device Connected!
Enter SVC ...
Waiting Device ...
Check SVC ...
SVC : DiagChannel opened!

Boot Done!

Format FFS Done!

Done!
Elapsed: 00:00:20

Reconnect Power/Cable!

A.G.Shahid · 07-11-2020, 06:42

Card found : 73CA70CC , v0144
Infinity-Box Chinese Miracle II : SC/RDA Module [SCR] v1.06

SCRD mode : AUTO
SPRD mode : SC6530 : REV : 0000 : NOR : [ 4MB-8MB ]

Operation : Identify [ v1.06 ]

----- > Powered On :
1. Power On device
2. Connect USB cable
3. When device show StorageMode : Press '0' button for a 5 second!
----- > Powered Off :
1. Insert USB cable
2. Wait when device show Charge icon
3. When device show StorageMode : Press '0' button for a 5 second!

Wait for device ...

Device Connected!
BOOT_PWR0 : 0x00600000
BOOT_INIT : 0x81C0024C
BOOT_MODE : DOWNLOAD
Setting BOOTROM mode
BOOT_MODE : BOOTROM
Boot_CPU : 0x88094007 : [RDA] : RDA8851L
MEMD for flsh_spi32m Branch: none
Boot_CS0 : 0x161660C8 : SPI : [GIGADEVICE] : GD25Q32 : 0x00400000 [ 4MiB ]
Performing MemoryInit
Selecting RL
Sending RL
Config : MemoryInit
Config : Loader
BOOT_MODE : RLOADER
Boot IV : 0xFBA2A2E0
Boot done!

Identify : Code Integrity Check pass!

Device Info Details :
[0] : X9B
[1] : 8809
[2] : CT8851B
[3] : pasw_rda6625
[4] : flsh_spi32m
[5] : gc9106/st7735r/gc9102/NV3021/gc9108/gc9104
[6] : byd3A01/gc6123/gc6113/gc6133/byd3a02serial/sp0821/pas6175/sp0829/gc6153_x
[7] : rdabt_8809
[8] : rdafm_8809
[9] : 20190909Mon1721
[10] : OT_L1i_Classic_Qmobile_HSD7735XL91049106BOE9108_BY DGDSP_EnFrArPeUd_190909

Security Info :
IMEI[1] :
IMEI[2] :
IMEI[3] :
IMEI[4] :
BT_ADDR : 780096340954

Done!
Elapsed: 00:03:31

Reconnect Power/Cable!

Operation : Reset Settings [ v1.06 ]
----- > Powered On :
1. Power On device
2. Connect USB cable
3. When device show StorageMode : Press '0' button for a 5 second!
----- > Powered Off :
1. Insert USB cable
2. Wait when device show Charge icon
3. When device show StorageMode : Press '0' button for a 5 second!

Wait for device ...

Device Connected!
BOOT_PWR0 : 0x00600000
BOOT_INIT : 0x81C0024C
BOOT_MODE : DOWNLOAD
Setting BOOTROM mode
BOOT_MODE : BOOTROM
Boot_CPU : 0x88094007 : [RDA] : RDA8851L
MEMD for flsh_spi32m Branch: none
Boot_CS0 : 0x161660C8 : SPI : [GIGADEVICE] : GD25Q32 : 0x00400000 [ 4MiB ]
Performing MemoryInit
Selecting RL
Sending RL
Config : MemoryInit
Config : Loader
BOOT_MODE : RLOADER
Boot IV : 0xFBA2A2E0
Boot done!

Preparing PMT
Verifying PMT
Erasing 1097728 bytes

FileSystem format done!

Done!
Elapsed: 00:01:33

Reconnect Power/Cable!

A.G.Shahid · 07-11-2020, 06:46

Card found : 73CA70CC , v0144
Infinity-Box Chinese Miracle II : SPD/USC Module [SP2] v2.05

Load IDBase v42913 Ok!

Operation : Identify [ v2.05 ]
BootMode : FLASH

1. Power off device, wait 10-15 seconds
2. Press and hold BooKey ( 1 : BOTH VOL , 2 : VOL+ , 3 : VOL- )
3. Insert cable in device!

Wait for device ...

Device Connected!
BootVersion : SPRD3
Boot : INF : 0_SC9850x_BASE : SC9850_eMMC_1GB_RS
Sending Init Boot ...
Boot sent!
Kick FDL ...
BootVersion : Spreadtrum Boot Block version 1.1
Protocol setup ...
Port speed : 921600
Sending Flash Boot ...
Boot sent!
Kick FLASH FDL ...
FDL : Control transfered!

Boot Done!

Device info :
Patch Level : OPM2.171019.012
Display ID : QSmartLT200_MP_11_09
Ver. Incmt : 20190911203243
Ver. CodeName : REL
Ver. Release : 8.1.0
Sec. Patch : 2019-08-05
Build Time : 1568205071
Product Model : LT200
Product Brand : QSmart
Product Name : LT200
Product Device : LT200
Product Manfct : QMobile
Product Info : LT200
Product Board : sp9850ka_1h10
Board Platform : sp9850ka

Platform Version: MOCORTM_18A_RLS2_W18.24.4_P2_Debug
Project Version: sharkl2_pub
BASE Version: FM_BASE_18A_RLS2_W18.24.4_P2
HW Version: sc9850_modem
CMP_Time : 07-02-2018 12:51:09

MODEM TAG : MOCORTM_18A_RLS2_W18.24.4_P2_Debug_FM_BASE_18A_RLS 2_W18.24.4_P2_sc9850_modem_sharkl2_pub

UserData : STATE : PLAIN [EXTFS]

Done!
Elapsed: 00:02:13

Operation : Format FS / Reset Settings [ v2.05 ]
Mode : Reset FRP
BootMode : FLASH

1. Power off device, wait 10-15 seconds
2. Press and hold BooKey ( 1 : BOTH VOL , 2 : VOL+ , 3 : VOL- )
3. Insert cable in device!

Wait for device ...

Device Connected!
BootVersion : SPRD3
Boot : INF : 0_SC9850x_BASE : SC9850_eMMC_1GB_RS
Sending Init Boot ...
Boot sent!
Kick FDL ...
BootVersion : Spreadtrum Boot Block version 1.1
Protocol setup ...
Port speed : 921600
Sending Flash Boot ...
Boot sent!
Kick FLASH FDL ...
FDL : Control transfered!

Boot Done!

Wipe Ok : FRP

Reconnect Power/Cable!

Done!
Elapsed: 00:00:51

Akhtar Ali Jatt · 07-11-2020, 07:29

Core : v2.29 , BB5XG FlashEngine : v10.5

Selected FlashSettings : Manual
Check FlashFiles, Please, wait...

Files Set for Flashing :
MCU : rm827__03.51.mcusw
PPM : rm827__03.51.ppm_m2
CNT : rm827__03.51.image_m2_059N2R0
Flashing phone now...
[Gen] Rules accepted for : XGOLD Generation
Check files done...
-> SWversion check skipped : Dead mode selected
Dead Mode is Selected
Waiting for USB device...

-> If Windows say "Unrecognized device" / Operation not start
-> Or if Phone start charge - just reinsert battery
-> If flashing freeze - reinsert cable/battery and try again
--- Press phone's power button or insert usb cable! ---

Connection opened successfully

IF Boot Init : 0xF0
IF Resp Len : 0x0A
IF xCPUID : XGOLD 213 [XMM2130 QUANTUM]
IF Resp Data : 1FB300020303010100FF

Sending EBL Loader ...
EBL Loader Ok, 01
EBL Loader ready, AA
Sending EBL ...
EBL sent Ok
EBL : Quantum_Bootloader_10.49_M1S1
Speed accepted, use 6.500.000
FLASHID : EC001230
FLIC conf set, RST set
Boot done!

Check keys...
Check done. Image can be flashed

Backup enabled, will read all certificates

Reading CCC
Reading HWC
Reading NPC

IMEI 1 : 358353054129821
IMEI 2 : 358353054129839
PCcode : 059N2R6

NPC Certificate saved...
CCC Certificate saved...
HWC Certificate saved...

RPL saved : C:\InfinityBox\BEST\Backup\Cert\358353054129821_XG 213_CRT.rpl

Settings : EDM [0x8] , Block Mode , Fast CRC , Verify

===Flashing [MCU]===
File : rm827__03.51.mcusw
Image : rm827__03.51.mcusw_ebl_psi.fls
Sec-pack found, sending ...
Sec-pack sent
Found 5 region(s)
Processing Region 1/5
Erase , Start : 0x40000000 , Len : 0x00020000
Erasing, wait ...
Erase done, time : 00:00:00
Write , Start : 0x40000000 , Len : 0x00020000
Flashing , wait ...
Region flash done, time : 00:00:00
Processing Region 2/5
Erase , Start : 0x40040000 , Len : 0x00020000
Erasing, wait ...
Erase done, time : 00:00:00
Write , Start : 0x40040000 , Len : 0x00020000
Flashing , wait ...
Region flash done, time : 00:00:00
Processing Region 3/5
Erase , Start : 0x40060000 , Len : 0x00100000
Erasing, wait ...
Erase done, time : 00:00:02
Write , Start : 0x40060000 , Len : 0x00100000
Flashing , wait ...
Region flash done, time : 00:00:01
Processing Region 4/5
Erase , Start : 0x40280000 , Len : 0x01940000
Erasing, wait ...
Erase done, time : 00:00:50
Write , Start : 0x40280000 , Len : 0x018C0000
Flashing , wait ...
Region flash done, time : 00:00:30
Processing Region 5/5
Erase , Start : 0x43E20000 , Len : 0x00040000
Erasing, wait ...
Erase done, time : 00:00:00
No write data, skip
CRC check passed , 0xA3D6

===Flashing [PPM]===
File : rm827__03.51.ppm_m2
Image : package_m2.ppm_ebl_psi.fls
Sec-pack found, sending ...
Sec-pack sent
Found 1 region(s)
Processing Region 1/1
Erase , Start : 0x41BC0000 , Len : 0x00600000
Erasing, wait ...
Erase done, time : 00:00:06
Write , Start : 0x41BC0000 , Len : 0x0030F748
Flashing , wait ...
Region flash done, time : 00:00:03
CRC check passed , 0x4605

===Flashing [CNT]===
File : rm827__03.51.image_m2_059N2R0
Image : package_m2_059N2R0.image.fls
Sec-pack found, sending ...
Sec-pack sent
Found 2 region(s)
Processing Region 1/2
Erase , Start : 0x421C0000 , Len : 0x01C60000
Erasing, wait ...
Erase done, time : 00:01:10
Write , Start : 0x421C0000 , Len : 0x00F20000
Flashing , wait ...
Region flash done, time : 00:00:18
Processing Region 2/2
Erase , Start : 0x43E60000 , Len : 0x000E0000
Erasing, wait ...
Erase done, time : 00:00:02
No write data, skip
CRC check passed , 0x2091

Flashing done!
Total flash time : 00:03:07
Reboot phone now...

Reading Phone Info....
Connected phone - Nokia 110
Software Info: V 03.51 06-08-13 RM-827 (c) Nokia
IMEI: 358353054129821
PPM version : V 03.51 06-08-13 RM-827 (c) Nokia M2
Product code: 059N2R6
Wait, when phone will be ready ...
Checking...
SimLock status : SimLock is Ok
Security status : Security is Ok
Read Info Done!
Processing After Flash Defaults...
FullFactorySet... Ok!
UserDataDefaultsSet...OK!
ServiceDefaultsSet... Ok!
LeaveDefaultsSet... Ok!
ProductTuneSet...OK!
SwUpgradeSet...OK!
Check and Upload User Certificates ...
Total - 58 certs
Certificates found, skip upload ...
AfterFlash operations done ;D
Done!
Connect phone on selected interface...

Elapsed: 00:04:12
Connect phone on selected interface...

Phone found!
Series 40 Device detected!
read info... - Ok

Phone disconected!

Connect phone on selected interface...

Akhtar Ali Jatt · 07-11-2020, 07:46

Operation : Reset Settings/Format FS [ v2.12 ]
Mode : META

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek USB VCOM (Android) (COM28)
MODE : BOOTROM
PORT : 28
Waiting BOOT ack ...
BROM : Skip ACK verify
BROM : Init BROM
BROM init passed!
CHIP : MT6735 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000
TYPE : LEGACY MTK
BROM : SecLevel : 0x00000001
BROM : SecMode : SBC
BROM : BOOTROM
BROM : Configuring target for META

BROM : META configured!

INIT : META confirmed!

Boot done!

AP_CHIP : MT6737M,S01
AP_SWTM : Wed Jan 17 12:31:20 CST 2018
AP_SWVR : alps-mp-n0.mp1-V1.0.2_len6737m.35.n_P173
AP_HWVR : S01

Format Ok : UserData

Done!
Elapsed: 00:00:46

Reconnect Power/Cable!

Operation : Reset Settings/Format FS [ v2.12 ]
Mode : FRP [ RESET PROTECTION ]
1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek USB VCOM (Android) (COM28)
MODE : BOOTROM
PORT : 28
Waiting BOOT ack ...
BROM : Skip ACK verify
BROM : Init BROM
BROM init passed!
CHIP : MT6735 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000
TYPE : LEGACY MTK
BROM : SecLevel : 0x00000001
BROM : SecMode : SBC
BROM : BROM|BL : 0x05|0xFE
BROM : BOOTROM
MODE : 0_base : BASE_v2012 | Manual : Disabled
AGENT : Look for suitable BootChain in DA ...
AGENT : MTK_AllInOne_DA.bin
AGENT : Found MT6735
AGENT : MTK_DOWNLOAD_AGENT
BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ...
DA : AGENT started!
NAND : DEVICE NOT FOUND
NAND : 000000000000000000000000
eMMC : OK
eMMC : 150100524531424D42070EC0E0461177
DAInf: 4 : 2 : 155
DA : EXT_RAM NOT initialized!
eMMC : OK
eMMC : 520001154D423145C00E0742771146E0
NAND : DEVICE NOT FOUND
NAND : 000000000000000000000000
EMI : DEV : INFINITY
EMI : SRC : INFINITY-BOX_INTERNAL_EMIDB_v0
INIT : 0xBC : eMMC [ 0x00000000 : [ 0 B ] ]
DRAM : DRAM: 0xC0000000 [ 3.00 GB ]
DA : DRAM ready!
DA : BOOT to 2nd DA ...
DA : Receiving HW info

EMMC: 150100524531424D42070EC0E0462377
EMMC: VEN : SAMSUNG | OEM : 01 | DEV : RE1BMB
EMMC:
BOOT1 : 0x00400000 [ 4.00 MB ]
BOOT2 : 0x00400000 [ 4.00 MB ]
RPMB : 0x00400000 [ 4.00 MB ]
USER : 0x3A3E00000 [ 14.56 GB ]

SRAM: 0x00020000 [ 128.00 KB ]
DRAM: 0xC0000000 [ 3.00 GB ]

CHIP : MT6735 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000 , EVOL : 0x0000

RNID : 3EC0D788BA40EF10C1986A0C2E7A4C0F

STATUS : BLANK FLASH
BSTYLE : EMMC FLASH BOOT

DA : USB : FULL-SPEED
DA : USB : Change Port Speed
PTFN : MediaTek DA USB VCOM (Android) (COM48)
MODE : PRELOADER PORT
PORT : 48

Boot done!

Format Ok : RESET PROTECTION

Done!
Elapsed: 00:00:58

Reconnect Power/Cable!

Akhtar Ali Jatt · 07-11-2020, 08:11

Operation : Read UserCode [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey ( '*' )

Wait for phone...
Phone found! [ 28 ]
Sync...
Sync Ok, read regs...
Inital regs read done
Boot Info :
BB_CPU_ID : 6261
BB_CPU_HW : CB01
BB_CPU_SW : 0001
BB_CPU_SB : 8000
BB_CPU_NM : [MediaTek] MT6261_S0000
BB_CPU_SN : E4F28E30DE42DAEA82B87AA42ACFF629
BROM Protocol Version : 05
Setting...
Setting done , result code 0x000E
BROM stage done
Seek and prepare DownloadAgent
DownloadAgent matching HW Found!
DA verify and select done
Sending DA to target ...
DA_INFO : 0xC0 , Ver : 3.2 , BBID : 0x8E
SOC_VERIFY : 0xC1
BOOT_STYLE : SF_FLASH_BOOT
NOR Flash IC initialized
[0] : FLASH_VEN : 0x0113 , [Winbond] SF_W25Q32JV
[0] : FLASH_DIE : 00EF 0070 0016 0000
[0] : FLASH_LEN : 0x00400000
SDS_INFO : 0x003FE000 , 0x00002000
INT_RAM : 0x0000D000
EXT_RAM : 0x00400000

Read ExtData
Sorting ExtData
Reading UserCode

Active : Yes , Code : 3399

PLock|MobTrack : Not active

Done!
Elapsed: 00:00:05
Reconnect Power/Cable!

djj007 · 07-11-2020, 13:02

BBOOT KEY BOTH VOL

mbiborna · 07-11-2020, 13:39

Code:

Operation : Identify [ v2.12 ]
Mode : FLASH

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek PreLoader USB VCOM (Android) (COM7)
MODE : PRELOADER PORT
PORT : 7
Waiting BOOT ack ...
PRELOADER : ACK confirmed!
BROM : Init BROM
BROM init passed!
     CHIP : MT6765 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000
     TYPE : MODERN RAPHAEL
BROM : SecLevel : 0x00000005
BROM : SecMode  : SBC+SDA
BROM : BROM|BL  : 0xFF|0x03
BROM : PRELOADER PORT
MODE : INFINIX : SECURE_BASE | Manual : Disabled
BROM : SOCID : 39EADF9C2607892B892A97AAA0FF01E1F06D7423F4C7BAFFA08EC0E98AC18724
AGENT : Look for suitable BootChain in DA ... 
AGENT : MTK_AllInOne_DA_SWSEC.bin
AGENT : Found MT6765
AGENT : MTK_DOWNLOAD_AGENT
     BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ... 
     DA : AGENT started!
DA : SYNC
     DA : MODE : PRELOADER
DA : EXT_RAM initialized!
DA : BOOT to 2nd DA ...
DA : 2ND stage confirmed!
DA : SYNC with DA passed!
DA : Receiving HW info

        SRAM: 0x00080000 [ 512.00 KB ]
        DRAM: 0x100000000 [ 4.00 GB ]

        EMMC: 90014A484347386134A214008635B51D
        EMMC: VEN : HYNIX | OEM : 4A01 | DEV : HCG8a4
        EMMC: 
              BOOT1  : 0x00400000 [ 4.00 MB ]
              BOOT2  : 0x00400000 [ 4.00 MB ]
              RPMB   : 0x00400000 [ 4.00 MB ]
              USER   : 0xE8F800000 [ 58.24 GB ]

        CHIP : MT6765 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000 , EVOL : 0x0000

        RNID : CCD04737FDEA8FB61295CE87F487622F

DA : USB : HIGH-SPEED

Boot done!

Patch Level    : PPR1.180610.011
Display ID     : X650C-H626DE-P-190901V209
Ver. CodeName  : REL
Ver. Release   : 9
Sec. Patch     : 2019-08-05
Build Time     : 1567313138
Product Model  : Infinix X650C
Product Brand  : Infinix
Product Name   : H626
Product Device : Infinix-X650C
Product Manfct : INFINIX MOBILITY LIMITED
Product Info   : x650c_h626
Product Board  : Infinix-X650C
Board Platform : mt6765

USERDATA : FILESYSTEM : F2FS  with FDE ( Full Disk Encryption *)

NVRAM check : Passed!
NVRAM : SEC NORMAL  [ No extra security ]

STORAGE : LifeStatus : Verify NOT supported by DA/HW!

Done!
Elapsed: 00:00:18

Operation : Reset Settings/Format FS [ v2.12 ]
Mode : FRP [ RESET PROTECTION ]
1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek PreLoader USB VCOM (Android) (COM7)
MODE : PRELOADER PORT
PORT : 7
Waiting BOOT ack ...
PRELOADER : ACK confirmed!
BROM : Init BROM
BROM init passed!
     CHIP : MT6765 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000
     TYPE : MODERN RAPHAEL
BROM : SecLevel : 0x00000005
BROM : SecMode  : SBC+SDA
BROM : BROM|BL  : 0xFF|0x03
BROM : PRELOADER PORT
MODE : INFINIX : SECURE_BASE | Manual : Disabled
BROM : SOCID : 39EADF9C2607892B892A97AAA0FF01E1F06D7423F4C7BAFFA08EC0E98AC18724
AGENT : Look for suitable BootChain in DA ... 
AGENT : MTK_AllInOne_DA_SWSEC.bin
AGENT : Found MT6765
AGENT : MTK_DOWNLOAD_AGENT
     BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ... 
     DA : AGENT started!
DA : SYNC
     DA : MODE : PRELOADER
DA : EXT_RAM initialized!
DA : BOOT to 2nd DA ...
DA : 2ND stage confirmed!
DA : SYNC with DA passed!
DA : Receiving HW info

        SRAM: 0x00080000 [ 512.00 KB ]
        DRAM: 0x100000000 [ 4.00 GB ]

        EMMC: 90014A484347386134A214008635B51D
        EMMC: VEN : HYNIX | OEM : 4A01 | DEV : HCG8a4
        EMMC: 
              BOOT1  : 0x00400000 [ 4.00 MB ]
              BOOT2  : 0x00400000 [ 4.00 MB ]
              RPMB   : 0x00400000 [ 4.00 MB ]
              USER   : 0xE8F800000 [ 58.24 GB ]

        CHIP : MT6765 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000 , EVOL : 0x0000

        RNID : CCD04737FDEA8FB61295CE87F487622F

DA : USB : HIGH-SPEED

Boot done!

Format Ok : RESET PROTECTION

Done!
Elapsed: 00:00:16

Reconnect Power/Cable!

azhergoga007 · 07-12-2020, 09:26

Code:

Card found : S/N : A19EC787 , v0143
Chinese Miracle II  [MTK module] v 1.58

Operation : Format FileSystem [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 8 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6580
BB_CPU_NME : [MediaTek] MT6580_S00
BB_CPU_EXT : 0xCA00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer   : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x94
NAND Flash : NOT INSTALLED
eMMC Flash : 7001004548384545380105D8885C34C7
Initialize Memory ... 
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x70 , OEM : 0100
[eMMC] : FLASH_INF : [KINGSTON] , 8EE8H
[eMMC] : FLASH_CID : 7001004548384545380105D8885C34C7
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00400000
[eMMC] : FLASH_LEN : 0x00000001C8000000
[eMMC] : FLASH_UCP : 7296 MiB [eMMC 8 GiB]
DEV RID    : 0xD9C8F395CB1D8D4232F3F3CBC0475C17
INT RAM    : 0x00020000
EXT RAM    : 0x40000000 [1 GiB]
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!


Clear FRP ( Google Reset Protection )
Clear Ok!

Done!
Elapsed: 00:00:15
Reconnect Power/Cable!

azhergoga007 · 07-12-2020, 09:44

Code:

Card found : S/N : A19EC787 , v0143
Chinese Miracle II  [MTK module] v 1.58

Operation : Format FileSystem [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 8 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6580
BB_CPU_NME : [MediaTek] MT6580_S00
BB_CPU_EXT : 0xCA00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer   : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x94
NAND Flash : NOT INSTALLED
eMMC Flash : 7001004548384545380105D8885C34C7
Initialize Memory ... 
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x70 , OEM : 0100
[eMMC] : FLASH_INF : [KINGSTON] , 8EE8H
[eMMC] : FLASH_CID : 7001004548384545380105D8885C34C7
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00400000
[eMMC] : FLASH_LEN : 0x00000001C8000000
[eMMC] : FLASH_UCP : 7296 MiB [eMMC 8 GiB]
DEV RID    : 0xD9C8F395CB1D8D4232F3F3CBC0475C17
INT RAM    : 0x00020000
EXT RAM    : 0x40000000 [1 GiB]
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!


Clear FRP ( Google Reset Protection )
Clear Ok!

Done!
Elapsed: 00:00:15
Reconnect Power/Cable!


Operation : Format FileSystem [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 8 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6580
BB_CPU_NME : [MediaTek] MT6580_S00
BB_CPU_EXT : 0xCA00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer   : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x94
NAND Flash : NOT INSTALLED
eMMC Flash : 7001004548384545380105D8885C34C7
Initialize Memory ... 
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x70 , OEM : 0100
[eMMC] : FLASH_INF : [KINGSTON] , 8EE8H
[eMMC] : FLASH_CID : 7001004548384545380105D8885C34C7
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00400000
[eMMC] : FLASH_LEN : 0x00000001C8000000
[eMMC] : FLASH_UCP : 7296 MiB [eMMC 8 GiB]
DEV RID    : 0xD9C8F395CB1D8D4232F3F3CBC0475C17
INT RAM    : 0x00020000
EXT RAM    : 0x40000000 [1 GiB]
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!


Clear FRP ( Google Reset Protection )
Clear Ok!
Clear DIN
Clear Ok!
Clear USERDATA
Clear Ok!
Clear CACHE
Clear Ok!

Done!
Elapsed: 00:00:38
Reconnect Power/Cable!


Operation : Read Flash [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 8 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6580
BB_CPU_NME : [MediaTek] MT6580_S00
BB_CPU_EXT : 0xCA00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer   : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x94
NAND Flash : NOT INSTALLED
eMMC Flash : 7001004548384545380105D8885C34C7
Initialize Memory ... 
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x70 , OEM : 0100
[eMMC] : FLASH_INF : [KINGSTON] , 8EE8H
[eMMC] : FLASH_CID : 7001004548384545380105D8885C34C7
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00400000
[eMMC] : FLASH_LEN : 0x00000001C8000000
[eMMC] : FLASH_UCP : 7296 MiB [eMMC 8 GiB]
DEV RID    : 0xD9C8F395CB1D8D4232F3F3CBC0475C17
INT RAM    : 0x00020000
EXT RAM    : 0x40000000 [1 GiB]
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

Reading Flash Content now ... 

xGPT : Normalize settings Ok!

Brand     : QMobile
ProdName  : Evok_Power_Lite
ProdModel : QMobile Evok Power Lite
Device    : Evok_Power_Lite
AndroidVer: 7.0
MTKxCPU   : MT6580
MTKxPRJ   : alps-mp-n0.mp2-V1_wtk6580.we.n

[Read Ok] : preloader_s5033c_qmobile_s2_we.bin
[Read Ok] : lk.bin
[Read Ok] : boot.img
[Read Ok] : recovery.img
[Read Ok] : logo.bin
[Read Ok] : tz1.img
[Read Ok] : tz2.img
[Read Ok] : secro.img
[Read Ok] : system.img
[Read Ok] : cache.img
[Read Ok] : userdata.img

[ScatCFG] : MT6580 / V1.1.2 / s5033c_qmobile_s2_we / EMMC
Android Info saved
HWConfig Info saved
FW Size : 2721 MiB
Scatter saved to : C:\Users\Azher\Desktop\MT6580__QMobile__QMobile_Evok_Power_Lite__Evok_Power_Lite__7.0__alps-mp-n0.mp2-V1_wtk6580.we.n\

All done!

Done!
Elapsed: 00:12:26
Reconnect Power/Cable!


Operation : HW Test [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 8 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6580
BB_CPU_NME : [MediaTek] MT6580_S00
BB_CPU_EXT : 0xCA00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer   : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x94
NAND Flash : NOT INSTALLED
eMMC Flash : 90014A483847316505072B626C4E24CB
Initialize Memory ... 
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x90 , OEM : 014A
[eMMC] : FLASH_INF : [HYNIX] , e1G8
[eMMC] : FLASH_CID : 90014A483847316505072B626C4E24CB
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00400000
[eMMC] : FLASH_LEN : 0x00000001D2000000
[eMMC] : FLASH_UCP : 7456 MiB [eMMC 8 GiB]
DEV RID    : 0xD9C8F395F8AF52A5E3D68CDAEC9F47A3
INT RAM    : 0x00020000
EXT RAM    : 0x40000000 [1 GiB]
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!


[Processing] FlashMemory Read-Write test
[eMMC] : [HYNIX] , e1G8 , 0x1D2000000 , 7456 MiB
[eMMC] : CID : 90014A483847316505072B626C4E24CB

[eMMC] : MODE : SQ-WR
[PASSED] : eMMC RW Check #1 Ok!
[eMMC] : MODE : RA-WR
[PASSED] : eMMC RW Check #2 Ok!

[eMMC RO CHECK] : eMMC Ok! READ-WRITE Passed!

All Done!

Done!
Elapsed: 00:00:27
Reconnect Power/Cable!


Operation : Format FileSystem [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 8 ]
Sync...
Open port error , something went wrong!
Boot Error!

Operation Failed
Elapsed: 00:00:00
Reconnect Power/Cable!


Operation : Format FileSystem [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 8 ]
Sync...
Open port error , something went wrong!
Boot Error!

Operation Failed
Elapsed: 00:00:00
Reconnect Power/Cable!


Operation : Format FileSystem [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 8 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6580
BB_CPU_NME : [MediaTek] MT6580_S00
BB_CPU_EXT : 0xCA00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer   : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x94
NAND Flash : NOT INSTALLED
eMMC Flash : 90014A483847316505072B626C4E24CB
Initialize Memory ... 
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x90 , OEM : 014A
[eMMC] : FLASH_INF : [HYNIX] , e1G8
[eMMC] : FLASH_CID : 90014A483847316505072B626C4E24CB
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00400000
[eMMC] : FLASH_LEN : 0x00000001D2000000
[eMMC] : FLASH_UCP : 7456 MiB [eMMC 8 GiB]
DEV RID    : 0xD9C8F395F8AF52A5E3D68CDAEC9F47A3
INT RAM    : 0x00020000
EXT RAM    : 0x40000000 [1 GiB]
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!


Clear FRP ( Google Reset Protection )
Clear Ok!
Clear DIN
Clear Ok!
Clear USERDATA
Clear Ok!
Clear CACHE
Clear Ok!

Done!
Elapsed: 00:00:36
Reconnect Power/Cable!

Akhtar Ali Jatt · 07-12-2020, 12:20

Operation : Reset Settings/Format FS [ v2.12 ]
Mode : FRP [ RESET PROTECTION ]
1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : PreLoader USB VCOM Port (COM20)
MODE : PRELOADER PORT
PORT : 20
Waiting BOOT ack ...
PRELOADER : ACK confirmed!
BROM : Init BROM
BROM init passed!
CHIP : MT6739 , SBID : 0x8A00 , HWVR : 0xCB00 , SWVR : 0x0002
TYPE : MODERN RAPHAEL
BROM : SecLevel : 0x00000001
BROM : SecMode : SBC
BROM : BROM|BL : 0xFF|0x03
BROM : PRELOADER PORT
MODE : Wiko : SEC_6739 | Manual : Disabled
BROM : SOCID : 3E5FD3433E7CAF69D8E6C6C697482CA1462F10A9D4E012D83A 3C72D0AFA3537B
AGENT : Look for suitable BootChain in DA ...
AGENT : DA_PL.bin
AGENT : Found MT6739
AGENT : MTK_DOWNLOAD_AGENT
BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ...
DA : AGENT started!
DA : SYNC
DA : MODE : PRELOADER
DA : EXT_RAM initialized!
DA : BOOT to 2nd DA ...
DA : 2ND stage confirmed!
DA : SYNC with DA passed!
DA : Receiving HW info

SRAM: 0x00040000 [ 256.00 KB ]
DRAM: 0x40000000 [ 1.00 GB ]

EMMC: 880103455042313030492DDC226085D3
EMMC: VEN : FORESEE | OEM : 301 | DEV : EPB100
EMMC:
BOOT1 : 0x00400000 [ 4.00 MB ]
BOOT2 : 0x00400000 [ 4.00 MB ]
RPMB : 0x00400000 [ 4.00 MB ]
USER : 0x1CE100000 [ 7.22 GB ]

CHIP : MT6739 , SBID : 0x8A00 , HWVR : 0xCB00 , SWVR : 0x0000 , EVOL : 0x0000

RNID : 5C51BBF22F1F80978516BFB2E30D089C

DA : USB : HIGH-SPEED

Boot done!

Format Ok : RESET PROTECTION

Done!
Elapsed: 00:00:13

Reconnect Power/Cable!

azhergoga007 · 07-13-2020, 06:51

Code:

Card found: S/N : A19EC787 , v0143
Chinese Miracle II  [SPD module] v 1.27

Set mode to : SP [SC773x] eMMC [Generic 4.x-5.0]

Operation : Format File System / Reset Settings [ v1.27 ]
Settings : SmartFormat is On

1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
 -> Alternative : just ONE 'VolumeUp' or 'VolumeDown' key 
3. Insert cable

 ====  Wait for phone...

Phone found! [ 6 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SPRD 773x eMMC loader v3 Infinity
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

FlashMode Set : Ok!
Checking Structure ... 
Detected eMMC Flash , Structure detect Ok!

eMMC phone detected! Will use 'Safe Format' mode!

Mount : /data
Size  : 0x000000012E5FC000
State : 0x0001

Mount : /cache
Size  : 0x0000000009600000
State : 0x0001

Prepare Ok! Format Ok!
Don't touch phone, until it fully bootup to "Welcome Screen"!

Done!

Elapsed: 00:00:36

Reconnect Power/Cable!

amjadnona · 07-13-2020, 07:37

Card found : A9EC786B , v0144
Infinity-Box Chinese Miracle II : SC/RDA Module [SCR] v1.06

SCRD mode : AUTO
SPRD mode : SC6530 : REV : 0000 : NOR : [ 4MB-8MB ]

Operation : Identify [ v1.06 ]
BootMode : SVC

1. Power off device
2. Not hold any key on device!
3. Insert cable and battery in device!

Wait for device ...

Device Connected!
Enter SVC ...
Waiting Device ...
Check SVC ...
SVC : DiagChannel opened!

Boot Done!

SOC GEN : SPRD ( Legacy )
ModemInfo :
Platform Version: MOCOR_16A.KING_W19.40.7_Release
BASE Version: BASE_SVN
HW Version: SC6531EFM_BAR
CMP_Time : 07-10-2019 15:56:03

SecInfo :
IMEI[1] : 35XXXXXXXXXXXX
IMEI[2] : 35XXXXXXXXXXXX
IMEI[3] : 000000000000000
WIFIMAC : FFFFFFFFFFFF
BT_MAC : FFFFFFFFFFFF
SEC_ID : B66DFFFF53CD65BB

Done!
Elapsed: 00:01:03

Reconnect Power/Cable!

Operation : Format FileSystem [ v1.06 ]

1. Power off device
2. Not hold any key on device!
3. Insert cable and battery in device!

Wait for device ...

Device Connected!
Enter SVC ...
Waiting Device ...
Check SVC ...
SVC : DiagChannel opened!

Boot Done!

Format FFS Done!

Done!
Elapsed: 00:00:52

Reconnect Power/Cable!

azhergoga007 · 07-13-2020, 08:46

Code:

Card found : S/N : A19EC787 , v0143
Chinese Miracle II  [MTK module] v 1.58

Operation : Format FileSystem [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 8 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6580
BB_CPU_NME : [MediaTek] MT6580_S00
BB_CPU_EXT : 0xCA00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer   : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x94
NAND Flash : NOT INSTALLED
eMMC Flash : 7001004548384345380106040B9F7309
Initialize Memory ... 
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x70 , OEM : 0100
[eMMC] : FLASH_INF : [KINGSTON] , 8EC8H
[eMMC] : FLASH_CID : 7001004548384345380106040B9F7309
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00400000
[eMMC] : FLASH_LEN : 0x00000001C8000000
[eMMC] : FLASH_UCP : 7296 MiB [eMMC 8 GiB]
DEV RID    : 0xD9C8F395E7CE3E9DFA92E375D0065F3E
INT RAM    : 0x00020000
EXT RAM    : 0x40000000 [1 GiB]
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!


Clear FRP ( Google Reset Protection )
Clear Ok!
Clear DIN
Clear Ok!
Clear USERDATA
Clear Ok!
Clear CACHE
Clear Ok!

Done!
Elapsed: 00:00:42
Reconnect Power/Cable!

localizator · 07-13-2020, 08:55

Code:

Operation : Identify [ v2.12 ]
Mode : FLASH

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek PreLoader USB VCOM (Android) (COM5)
MODE : PRELOADER PORT
PORT : 5
Waiting BOOT ack ...
PRELOADER : ACK confirmed!
BROM : Init BROM
BROM init passed!
     CHIP : MT6739 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000
     TYPE : MODERN RAPHAEL
BROM : SecLevel : 0x00000000
BROM : SecMode  : PLAIN [+PRL]
BROM : BROM|BL  : 0xFF|0x03
BROM : PRELOADER PORT
MODE : 0_base : BASE_v2012 | Manual : Disabled
BROM : SOCID : 9E8436652912E5916D1CE83B8FB1194879542D2B90177E1D918B0D974D643E35
AGENT : Look for suitable BootChain in DA ... 
AGENT : MTK_AllInOne_DA.bin
AGENT : Found MT6739
AGENT : MTK_DOWNLOAD_AGENT
     BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ... 
     DA : AGENT started!
DA : SYNC
     DA : MODE : PRELOADER
DA : EXT_RAM initialized!
DA : BOOT to 2nd DA ...
DA : 2ND stage confirmed!
DA : SYNC with DA passed!
DA : Receiving HW info

        SRAM: 0x00020000 [ 128,00 KB ]
        DRAM: 0x40000000 [ 1,00 GB ]

        EMMC: 8801034D384231364728DC6F47227573
        EMMC: VEN : FORESEE | OEM : 301 | DEV : M8B16G
        EMMC: 
              BOOT1  : 0x00400000 [ 4,00 MB ]
              BOOT2  : 0x00400000 [ 4,00 MB ]
              RPMB   : 0x00400000 [ 4,00 MB ]
              USER   : 0x39D000000 [ 14,45 GB ]

        CHIP : MT6739 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000 , EVOL : 0x0000

        RNID : B6416A731E38018BB50878535504DFCB

DA : USB : HIGH-SPEED

Boot done!

Patch Level    : O11019
Display ID     : 2E_F534L_V1.3_20180815
Ver. CodeName  : REL
Ver. Release   : 8.1.0
Sec. Patch     : 2018-07-05
Build Time     : 1534340704
Product Model  : F534L
Product Brand  : 2E
Product Name   : F534L
Product Device : F534L
Product Manfct : teksun
Product Info   : t939ha_v1_au_dd_f05_f534l_go
Product Board  : t939ha_v1_au_dd_f05_f534l_go
Board Platform : mt6739

USERDATA : FILESYSTEM : F2FS  with FDE ( Full Disk Encryption *)

NVRAM check : Passed!
NVRAM : SEC NORMAL  [ No extra security ]

STORAGE : LifeStatus : OK!

Done!
Elapsed: 00:00:35

Code:

Operation : Write Flash [ v2.12 ]

Repartition   : Enabled
Flash Verify  : Disabled
Reg.Pre-Erase : Enabled
Verify HW/SW  : Enabled
SData Backup  : Disabled
Safe UserData : Disabled
Flash Format  : Disabled

Files :20
[FL] : Set : preloader_t939ha_v1_au_dd_f05_f534l_go.bin
[FL] : Set : recovery.img
[FL] : Set : md1img.img
[FL] : Set : md1dsp.img
[FL] : Set : spmfw.img
[FL] : Set : mcupmfw.img
[FL] : Set : lk.img
[FL] : Set : lk.img
[FL] : Set : loader_ext.img
[FL] : Set : loader_ext.img
[FL] : Set : boot.img
[FL] : Set : logo.bin
[FL] : Set : odmdtbo.img
[FL] : Set : tee.img
[FL] : Set : tee.img
[FL] : Set : teksunhw.bin
[FL] : Set : vendor.img
[FL] : Set : system.img
[FL] : Set : cache.img
[FL] : Set : userdata.img

[FL] : Total size : 0x55370713 [ 1,33 GB ]

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek PreLoader USB VCOM (Android) (COM5)
MODE : PRELOADER PORT
PORT : 5
Waiting BOOT ack ...
PRELOADER : ACK confirmed!
BROM : Init BROM
BROM init passed!
     CHIP : MT6739 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000
     TYPE : MODERN RAPHAEL
BROM : SecLevel : 0x00000000
BROM : SecMode  : PLAIN [+PRL]
BROM : BROM|BL  : 0xFF|0x03
BROM : PRELOADER PORT
MODE : 0_base : BASE_v2012 | Manual : Disabled
BROM : SOCID : 9E8436652912E5916D1CE83B8FB1194879542D2B90177E1D918B0D974D643E35
AGENT : Look for suitable BootChain in DA ... 
AGENT : MTK_AllInOne_DA.bin
AGENT : Found MT6739
AGENT : MTK_DOWNLOAD_AGENT
     BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ... 
     DA : AGENT started!
DA : SYNC
     DA : MODE : PRELOADER
DA : EXT_RAM initialized!
DA : BOOT to 2nd DA ...
DA : 2ND stage confirmed!
DA : SYNC with DA passed!
DA : Receiving HW info

        SRAM: 0x00020000 [ 128,00 KB ]
        DRAM: 0x40000000 [ 1,00 GB ]

        EMMC: 8801034D384231364728DC6F47227573
        EMMC: VEN : FORESEE | OEM : 301 | DEV : M8B16G
        EMMC: 
              BOOT1  : 0x00400000 [ 4,00 MB ]
              BOOT2  : 0x00400000 [ 4,00 MB ]
              RPMB   : 0x00400000 [ 4,00 MB ]
              USER   : 0x39D000000 [ 14,45 GB ]

        CHIP : MT6739 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000 , EVOL : 0x0000

        RNID : B6416A731E38018BB50878535504DFCB

DA : USB : HIGH-SPEED

Boot done!

[FL] : HW verification passed!

SEC_DL : False (RAPHAEL)
SEC_ID : 0x494E46494E495459424F584245535432

[FL] : Pre-Erase 
Erase : 0x0000000000000000 : 0x0000000002E88000
Erase : 0x0000000003688000 : 0x0000000004000000
Erase : 0x0000000008800000 : 0x0000000000A00000
Erase : 0x0000000009500000 : 0x0000000007200000
Erase : 0x0000000010C00000 : 0x0000000000200000
Erase : 0x0000000010E20000 : 0x00000001291E0000

[FL] : RePartition 
[FL] : RePartition Ok!


[FL] : Flashing now ... 

Write : PRELOADER
Update bootloader backup copy ... 
Update bootloader backup copy Ok!
Write : RECOVERY
Write : MD1IMG
Write : MD1DSP
Write : SPMFW
Write : MCUPMFW
Write : LK
Write : LK2
Write : LOADER_EXT1
Write : LOADER_EXT2
Write : BOOT
Write : LOGO
Write : ODMDTBO
Write : TEE1
Write : TEE2
Write : TEKSUNHW
Write : VENDOR
Write : SYSTEM
Write : CACHE
Write : USERDATA

[FL] : RePartition 
[FL] : RePartition Ok!

[FL] : Flashing finished!

Done!
Elapsed: 00:01:22

07-11-2020, 06:30	#63706 (permalink)
A.G.Shahid No Life Poster Join Date: Nov 2016 Location: ISI Posts: 5,792 Member: 2644066 Status: Offline Thanks Meter: 1,773	Call me c12 hang on logo done by cm2 with out boot key Card found : 73CA70CC , v0144 Infinity-Box Chinese Miracle II : SC/RDA Module [SCR] v1.06 SCRD mode : AUTO SPRD mode : SC6530 : REV : 0000 : NOR : [ 4MB-8MB ] Operation : Identify [ v1.06 ] BootMode : SVC 1. Power off device 2. Not hold any key on device! 3. Insert cable and battery in device! Wait for device ... Device Connected! Enter SVC ... Waiting Device ... Check SVC ... SVC : DiagChannel opened! Boot Done! SOC GEN : SPRD ( Legacy ) ModemInfo : Project Version: SC6531EFM_BAR BASE Version: BASE_SVN HW Version: SC6531EFM_BAR CMP_Time : 01-15-2020 11:04:51 SecInfo : IMEI[1] : IMEI[2] : IMEI[3] : WIFIMAC : FFFFFFFFFFFF BT_MAC : 018321094528 SEC_ID : 7B9EFFFF39A561D3 Done! Elapsed: 00:00:20 Reconnect Power/Cable! Operation : Format FileSystem [ v1.06 ] 1. Power off device 2. Not hold any key on device! 3. Insert cable and battery in device! Wait for device ... Device Connected! Enter SVC ... Waiting Device ... Check SVC ... SVC : DiagChannel opened! Boot Done! Format FFS Done! Done! Elapsed: 00:00:20 Reconnect Power/Cable!

07-11-2020, 06:42	#63707 (permalink)
A.G.Shahid No Life Poster Join Date: Nov 2016 Location: ISI Posts: 5,792 Member: 2644066 Status: Offline Thanks Meter: 1,773	Qmobile l1i classic hang on logo done by cm2 Card found : 73CA70CC , v0144 Infinity-Box Chinese Miracle II : SC/RDA Module [SCR] v1.06 SCRD mode : AUTO SPRD mode : SC6530 : REV : 0000 : NOR : [ 4MB-8MB ] Operation : Identify [ v1.06 ] ----- > Powered On : 1. Power On device 2. Connect USB cable 3. When device show StorageMode : Press '0' button for a 5 second! ----- > Powered Off : 1. Insert USB cable 2. Wait when device show Charge icon 3. When device show StorageMode : Press '0' button for a 5 second! Wait for device ... Device Connected! BOOT_PWR0 : 0x00600000 BOOT_INIT : 0x81C0024C BOOT_MODE : DOWNLOAD Setting BOOTROM mode BOOT_MODE : BOOTROM Boot_CPU : 0x88094007 : [RDA] : RDA8851L MEMD for flsh_spi32m Branch: none Boot_CS0 : 0x161660C8 : SPI : [GIGADEVICE] : GD25Q32 : 0x00400000 [ 4MiB ] Performing MemoryInit Selecting RL Sending RL Config : MemoryInit Config : Loader BOOT_MODE : RLOADER Boot IV : 0xFBA2A2E0 Boot done! Identify : Code Integrity Check pass! Device Info Details : [0] : X9B [1] : 8809 [2] : CT8851B [3] : pasw_rda6625 [4] : flsh_spi32m [5] : gc9106/st7735r/gc9102/NV3021/gc9108/gc9104 [6] : byd3A01/gc6123/gc6113/gc6133/byd3a02serial/sp0821/pas6175/sp0829/gc6153_x [7] : rdabt_8809 [8] : rdafm_8809 [9] : 20190909Mon1721 [10] : OT_L1i_Classic_Qmobile_HSD7735XL91049106BOE9108_BY DGDSP_EnFrArPeUd_190909 Security Info : IMEI[1] : IMEI[2] : IMEI[3] : IMEI[4] : BT_ADDR : 780096340954 Done! Elapsed: 00:03:31 Reconnect Power/Cable! Operation : Reset Settings [ v1.06 ] ----- > Powered On : 1. Power On device 2. Connect USB cable 3. When device show StorageMode : Press '0' button for a 5 second! ----- > Powered Off : 1. Insert USB cable 2. Wait when device show Charge icon 3. When device show StorageMode : Press '0' button for a 5 second! Wait for device ... Device Connected! BOOT_PWR0 : 0x00600000 BOOT_INIT : 0x81C0024C BOOT_MODE : DOWNLOAD Setting BOOTROM mode BOOT_MODE : BOOTROM Boot_CPU : 0x88094007 : [RDA] : RDA8851L MEMD for flsh_spi32m Branch: none Boot_CS0 : 0x161660C8 : SPI : [GIGADEVICE] : GD25Q32 : 0x00400000 [ 4MiB ] Performing MemoryInit Selecting RL Sending RL Config : MemoryInit Config : Loader BOOT_MODE : RLOADER Boot IV : 0xFBA2A2E0 Boot done! Preparing PMT Verifying PMT Erasing 1097728 bytes FileSystem format done! Done! Elapsed: 00:01:33 Reconnect Power/Cable!

07-11-2020, 06:46	#63708 (permalink)
A.G.Shahid No Life Poster Join Date: Nov 2016 Location: ISI Posts: 5,792 Member: 2644066 Status: Offline Thanks Meter: 1,773	Qmobile lt200 reset frp done by cm2 Card found : 73CA70CC , v0144 Infinity-Box Chinese Miracle II : SPD/USC Module [SP2] v2.05 Load IDBase v42913 Ok! Operation : Identify [ v2.05 ] BootMode : FLASH 1. Power off device, wait 10-15 seconds 2. Press and hold BooKey ( 1 : BOTH VOL , 2 : VOL+ , 3 : VOL- ) 3. Insert cable in device! Wait for device ... Device Connected! BootVersion : SPRD3 Boot : INF : 0_SC9850x_BASE : SC9850_eMMC_1GB_RS Sending Init Boot ... Boot sent! Kick FDL ... BootVersion : Spreadtrum Boot Block version 1.1 Protocol setup ... Port speed : 921600 Sending Flash Boot ... Boot sent! Kick FLASH FDL ... FDL : Control transfered! Boot Done! Device info : Patch Level : OPM2.171019.012 Display ID : QSmartLT200_MP_11_09 Ver. Incmt : 20190911203243 Ver. CodeName : REL Ver. Release : 8.1.0 Sec. Patch : 2019-08-05 Build Time : 1568205071 Product Model : LT200 Product Brand : QSmart Product Name : LT200 Product Device : LT200 Product Manfct : QMobile Product Info : LT200 Product Board : sp9850ka_1h10 Board Platform : sp9850ka Platform Version: MOCORTM_18A_RLS2_W18.24.4_P2_Debug Project Version: sharkl2_pub BASE Version: FM_BASE_18A_RLS2_W18.24.4_P2 HW Version: sc9850_modem CMP_Time : 07-02-2018 12:51:09 MODEM TAG : MOCORTM_18A_RLS2_W18.24.4_P2_Debug_FM_BASE_18A_RLS 2_W18.24.4_P2_sc9850_modem_sharkl2_pub UserData : STATE : PLAIN [EXTFS] Done! Elapsed: 00:02:13 Operation : Format FS / Reset Settings [ v2.05 ] Mode : Reset FRP BootMode : FLASH 1. Power off device, wait 10-15 seconds 2. Press and hold BooKey ( 1 : BOTH VOL , 2 : VOL+ , 3 : VOL- ) 3. Insert cable in device! Wait for device ... Device Connected! BootVersion : SPRD3 Boot : INF : 0_SC9850x_BASE : SC9850_eMMC_1GB_RS Sending Init Boot ... Boot sent! Kick FDL ... BootVersion : Spreadtrum Boot Block version 1.1 Protocol setup ... Port speed : 921600 Sending Flash Boot ... Boot sent! Kick FLASH FDL ... FDL : Control transfered! Boot Done! Wipe Ok : FRP Reconnect Power/Cable! Done! Elapsed: 00:00:51

07-11-2020, 07:29	#63709 (permalink)
Akhtar Ali Jatt No Life Poster Join Date: Jan 2009 Location: Sindh Pakistan Posts: 8,876 Member: 953334 Status: Offline Sonork: 100.1614005 Thanks Meter: 15,424	Nokia 110 Core : v2.29 , BB5XG FlashEngine : v10.5 Selected FlashSettings : Manual Check FlashFiles, Please, wait... Files Set for Flashing : MCU : rm827__03.51.mcusw PPM : rm827__03.51.ppm_m2 CNT : rm827__03.51.image_m2_059N2R0 Flashing phone now... [Gen] Rules accepted for : XGOLD Generation Check files done... -> SWversion check skipped : Dead mode selected Dead Mode is Selected Waiting for USB device... -> If Windows say "Unrecognized device" / Operation not start -> Or if Phone start charge - just reinsert battery -> If flashing freeze - reinsert cable/battery and try again --- Press phone's power button or insert usb cable! --- Connection opened successfully IF Boot Init : 0xF0 IF Resp Len : 0x0A IF xCPUID : XGOLD 213 [XMM2130 QUANTUM] IF Resp Data : 1FB300020303010100FF Sending EBL Loader ... EBL Loader Ok, 01 EBL Loader ready, AA Sending EBL ... EBL sent Ok EBL : Quantum_Bootloader_10.49_M1S1 Speed accepted, use 6.500.000 FLASHID : EC001230 FLIC conf set, RST set Boot done! Check keys... Check done. Image can be flashed Backup enabled, will read all certificates Reading CCC Reading HWC Reading NPC IMEI 1 : 358353054129821 IMEI 2 : 358353054129839 PCcode : 059N2R6 NPC Certificate saved... CCC Certificate saved... HWC Certificate saved... RPL saved : C:\InfinityBox\BEST\Backup\Cert\358353054129821_XG 213_CRT.rpl Settings : EDM [0x8] , Block Mode , Fast CRC , Verify ===Flashing [MCU]=== File : rm827__03.51.mcusw Image : rm827__03.51.mcusw_ebl_psi.fls Sec-pack found, sending ... Sec-pack sent Found 5 region(s) Processing Region 1/5 Erase , Start : 0x40000000 , Len : 0x00020000 Erasing, wait ... Erase done, time : 00:00:00 Write , Start : 0x40000000 , Len : 0x00020000 Flashing , wait ... Region flash done, time : 00:00:00 Processing Region 2/5 Erase , Start : 0x40040000 , Len : 0x00020000 Erasing, wait ... Erase done, time : 00:00:00 Write , Start : 0x40040000 , Len : 0x00020000 Flashing , wait ... Region flash done, time : 00:00:00 Processing Region 3/5 Erase , Start : 0x40060000 , Len : 0x00100000 Erasing, wait ... Erase done, time : 00:00:02 Write , Start : 0x40060000 , Len : 0x00100000 Flashing , wait ... Region flash done, time : 00:00:01 Processing Region 4/5 Erase , Start : 0x40280000 , Len : 0x01940000 Erasing, wait ... Erase done, time : 00:00:50 Write , Start : 0x40280000 , Len : 0x018C0000 Flashing , wait ... Region flash done, time : 00:00:30 Processing Region 5/5 Erase , Start : 0x43E20000 , Len : 0x00040000 Erasing, wait ... Erase done, time : 00:00:00 No write data, skip CRC check passed , 0xA3D6 ===Flashing [PPM]=== File : rm827__03.51.ppm_m2 Image : package_m2.ppm_ebl_psi.fls Sec-pack found, sending ... Sec-pack sent Found 1 region(s) Processing Region 1/1 Erase , Start : 0x41BC0000 , Len : 0x00600000 Erasing, wait ... Erase done, time : 00:00:06 Write , Start : 0x41BC0000 , Len : 0x0030F748 Flashing , wait ... Region flash done, time : 00:00:03 CRC check passed , 0x4605 ===Flashing [CNT]=== File : rm827__03.51.image_m2_059N2R0 Image : package_m2_059N2R0.image.fls Sec-pack found, sending ... Sec-pack sent Found 2 region(s) Processing Region 1/2 Erase , Start : 0x421C0000 , Len : 0x01C60000 Erasing, wait ... Erase done, time : 00:01:10 Write , Start : 0x421C0000 , Len : 0x00F20000 Flashing , wait ... Region flash done, time : 00:00:18 Processing Region 2/2 Erase , Start : 0x43E60000 , Len : 0x000E0000 Erasing, wait ... Erase done, time : 00:00:02 No write data, skip CRC check passed , 0x2091 Flashing done! Total flash time : 00:03:07 Reboot phone now... Reading Phone Info.... Connected phone - Nokia 110 Software Info: V 03.51 06-08-13 RM-827 (c) Nokia IMEI: 358353054129821 PPM version : V 03.51 06-08-13 RM-827 (c) Nokia M2 Product code: 059N2R6 Wait, when phone will be ready ... Checking... SimLock status : SimLock is Ok Security status : Security is Ok Read Info Done! Processing After Flash Defaults... FullFactorySet... Ok! UserDataDefaultsSet...OK! ServiceDefaultsSet... Ok! LeaveDefaultsSet... Ok! ProductTuneSet...OK! SwUpgradeSet...OK! Check and Upload User Certificates ... Total - 58 certs Certificates found, skip upload ... AfterFlash operations done ;D Done! Connect phone on selected interface... Elapsed: 00:04:12 Connect phone on selected interface... Phone found! Series 40 Device detected! read info... - Ok Phone disconected! Connect phone on selected interface...

07-11-2020, 07:46	#63710 (permalink)
Akhtar Ali Jatt No Life Poster Join Date: Jan 2009 Location: Sindh Pakistan Posts: 8,876 Member: 953334 Status: Offline Sonork: 100.1614005 Thanks Meter: 15,424	Qmobile S15 Reset meta Mode And F.R.p Done Operation : Reset Settings/Format FS [ v2.12 ] Mode : META 1. Make sure device is powered off. Power off, if need. Wait 20 seconds after 2. Insert USB cable in phone Waiting for device connection ... PTFN : MediaTek USB VCOM (Android) (COM28) MODE : BOOTROM PORT : 28 Waiting BOOT ack ... BROM : Skip ACK verify BROM : Init BROM BROM init passed! CHIP : MT6735 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000 TYPE : LEGACY MTK BROM : SecLevel : 0x00000001 BROM : SecMode : SBC BROM : BOOTROM BROM : Configuring target for META BROM : META configured! INIT : META confirmed! Boot done! AP_CHIP : MT6737M,S01 AP_SWTM : Wed Jan 17 12:31:20 CST 2018 AP_SWVR : alps-mp-n0.mp1-V1.0.2_len6737m.35.n_P173 AP_HWVR : S01 Format Ok : UserData Done! Elapsed: 00:00:46 Reconnect Power/Cable! Operation : Reset Settings/Format FS [ v2.12 ] Mode : FRP [ RESET PROTECTION ] 1. Make sure device is powered off. Power off, if need. Wait 20 seconds after 2. Insert USB cable in phone Waiting for device connection ... PTFN : MediaTek USB VCOM (Android) (COM28) MODE : BOOTROM PORT : 28 Waiting BOOT ack ... BROM : Skip ACK verify BROM : Init BROM BROM init passed! CHIP : MT6735 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000 TYPE : LEGACY MTK BROM : SecLevel : 0x00000001 BROM : SecMode : SBC BROM : BROM\|BL : 0x05\|0xFE BROM : BOOTROM MODE : 0_base : BASE_v2012 \| Manual : Disabled AGENT : Look for suitable BootChain in DA ... AGENT : MTK_AllInOne_DA.bin AGENT : Found MT6735 AGENT : MTK_DOWNLOAD_AGENT BROM : Sending 1st DA ... BROM : DA sent BROM :Transfer control to DA ... DA : AGENT started! NAND : DEVICE NOT FOUND NAND : 000000000000000000000000 eMMC : OK eMMC : 150100524531424D42070EC0E0461177 DAInf: 4 : 2 : 155 DA : EXT_RAM NOT initialized! eMMC : OK eMMC : 520001154D423145C00E0742771146E0 NAND : DEVICE NOT FOUND NAND : 000000000000000000000000 EMI : DEV : INFINITY EMI : SRC : INFINITY-BOX_INTERNAL_EMIDB_v0 INIT : 0xBC : eMMC [ 0x00000000 : [ 0 B ] ] DRAM : DRAM: 0xC0000000 [ 3.00 GB ] DA : DRAM ready! DA : BOOT to 2nd DA ... DA : Receiving HW info EMMC: 150100524531424D42070EC0E0462377 EMMC: VEN : SAMSUNG \| OEM : 01 \| DEV : RE1BMB EMMC: BOOT1 : 0x00400000 [ 4.00 MB ] BOOT2 : 0x00400000 [ 4.00 MB ] RPMB : 0x00400000 [ 4.00 MB ] USER : 0x3A3E00000 [ 14.56 GB ] SRAM: 0x00020000 [ 128.00 KB ] DRAM: 0xC0000000 [ 3.00 GB ] CHIP : MT6735 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000 , EVOL : 0x0000 RNID : 3EC0D788BA40EF10C1986A0C2E7A4C0F STATUS : BLANK FLASH BSTYLE : EMMC FLASH BOOT DA : USB : FULL-SPEED DA : USB : Change Port Speed PTFN : MediaTek DA USB VCOM (Android) (COM48) MODE : PRELOADER PORT PORT : 48 Boot done! Format Ok : RESET PROTECTION Done! Elapsed: 00:00:58 Reconnect Power/Cable!

07-11-2020, 08:11	#63711 (permalink)
Akhtar Ali Jatt No Life Poster Join Date: Jan 2009 Location: Sindh Pakistan Posts: 8,876 Member: 953334 Status: Offline Sonork: 100.1614005 Thanks Meter: 15,424	VgoTel v3310 Read User Code Done Operation : Read UserCode [ v1.58 ] 1. Power Off Phone , Remove battery , Insert back 2. Insert USB cable. In some cases require hold BootKey ( '*' ) Wait for phone... Phone found! [ 28 ] Sync... Sync Ok, read regs... Inital regs read done Boot Info : BB_CPU_ID : 6261 BB_CPU_HW : CB01 BB_CPU_SW : 0001 BB_CPU_SB : 8000 BB_CPU_NM : [MediaTek] MT6261_S0000 BB_CPU_SN : E4F28E30DE42DAEA82B87AA42ACFF629 BROM Protocol Version : 05 Setting... Setting done , result code 0x000E BROM stage done Seek and prepare DownloadAgent DownloadAgent matching HW Found! DA verify and select done Sending DA to target ... DA_INFO : 0xC0 , Ver : 3.2 , BBID : 0x8E SOC_VERIFY : 0xC1 BOOT_STYLE : SF_FLASH_BOOT NOR Flash IC initialized [0] : FLASH_VEN : 0x0113 , [Winbond] SF_W25Q32JV [0] : FLASH_DIE : 00EF 0070 0016 0000 [0] : FLASH_LEN : 0x00400000 SDS_INFO : 0x003FE000 , 0x00002000 INT_RAM : 0x0000D000 EXT_RAM : 0x00400000 Read ExtData Sorting ExtData Reading UserCode Active : Yes , Code : 3399 PLock\|MobTrack : Not active Done! Elapsed: 00:00:05 Reconnect Power/Cable!

07-11-2020, 13:02	#63712 (permalink)
djj007 No Life Poster Join Date: Nov 2016 Location: GUJARAT Posts: 1,439 Member: 2643730 Status: Offline Thanks Meter: 1,115	Tambo ta-2 frp removed by king cm2 BBOOT KEY BOTH VOL

07-12-2020, 12:20	#63716 (permalink)
Akhtar Ali Jatt No Life Poster Join Date: Jan 2009 Location: Sindh Pakistan Posts: 8,876 Member: 953334 Status: Offline Sonork: 100.1614005 Thanks Meter: 15,424	Qmobile LT900 F.R.p Remove Done Just Select Wiko : SEC_6739 ! Operation : Reset Settings/Format FS [ v2.12 ] Mode : FRP [ RESET PROTECTION ] 1. Make sure device is powered off. Power off, if need. Wait 20 seconds after 2. Insert USB cable in phone Waiting for device connection ... PTFN : PreLoader USB VCOM Port (COM20) MODE : PRELOADER PORT PORT : 20 Waiting BOOT ack ... PRELOADER : ACK confirmed! BROM : Init BROM BROM init passed! CHIP : MT6739 , SBID : 0x8A00 , HWVR : 0xCB00 , SWVR : 0x0002 TYPE : MODERN RAPHAEL BROM : SecLevel : 0x00000001 BROM : SecMode : SBC BROM : BROM\|BL : 0xFF\|0x03 BROM : PRELOADER PORT MODE : Wiko : SEC_6739 \| Manual : Disabled BROM : SOCID : 3E5FD3433E7CAF69D8E6C6C697482CA1462F10A9D4E012D83A 3C72D0AFA3537B AGENT : Look for suitable BootChain in DA ... AGENT : DA_PL.bin AGENT : Found MT6739 AGENT : MTK_DOWNLOAD_AGENT BROM : Sending 1st DA ... BROM : DA sent BROM :Transfer control to DA ... DA : AGENT started! DA : SYNC DA : MODE : PRELOADER DA : EXT_RAM initialized! DA : BOOT to 2nd DA ... DA : 2ND stage confirmed! DA : SYNC with DA passed! DA : Receiving HW info SRAM: 0x00040000 [ 256.00 KB ] DRAM: 0x40000000 [ 1.00 GB ] EMMC: 880103455042313030492DDC226085D3 EMMC: VEN : FORESEE \| OEM : 301 \| DEV : EPB100 EMMC: BOOT1 : 0x00400000 [ 4.00 MB ] BOOT2 : 0x00400000 [ 4.00 MB ] RPMB : 0x00400000 [ 4.00 MB ] USER : 0x1CE100000 [ 7.22 GB ] CHIP : MT6739 , SBID : 0x8A00 , HWVR : 0xCB00 , SWVR : 0x0000 , EVOL : 0x0000 RNID : 5C51BBF22F1F80978516BFB2E30D089C DA : USB : HIGH-SPEED Boot done! Format Ok : RESET PROTECTION Done! Elapsed: 00:00:13 Reconnect Power/Cable!

07-13-2020, 07:37	#63718 (permalink)
amjadnona No Life Poster Join Date: Apr 2011 Location: Pakistan Posts: 934 Member: 1555233 Status: Offline Thanks Meter: 2,192	KING CM2 NOKIA 105 SC6531EFM_BAR Format FFS Done WITHOUT BOOT KEY SVC Mode Card found : A9EC786B , v0144 Infinity-Box Chinese Miracle II : SC/RDA Module [SCR] v1.06 SCRD mode : AUTO SPRD mode : SC6530 : REV : 0000 : NOR : [ 4MB-8MB ] Operation : Identify [ v1.06 ] BootMode : SVC 1. Power off device 2. Not hold any key on device! 3. Insert cable and battery in device! Wait for device ... Device Connected! Enter SVC ... Waiting Device ... Check SVC ... SVC : DiagChannel opened! Boot Done! SOC GEN : SPRD ( Legacy ) ModemInfo : Platform Version: MOCOR_16A.KING_W19.40.7_Release BASE Version: BASE_SVN HW Version: SC6531EFM_BAR CMP_Time : 07-10-2019 15:56:03 SecInfo : IMEI[1] : 35XXXXXXXXXXXX IMEI[2] : 35XXXXXXXXXXXX IMEI[3] : 000000000000000 WIFIMAC : FFFFFFFFFFFF BT_MAC : FFFFFFFFFFFF SEC_ID : B66DFFFF53CD65BB Done! Elapsed: 00:01:03 Reconnect Power/Cable! Operation : Format FileSystem [ v1.06 ] 1. Power off device 2. Not hold any key on device! 3. Insert cable and battery in device! Wait for device ... Device Connected! Enter SVC ... Waiting Device ... Check SVC ... SVC : DiagChannel opened! Boot Done! Format FFS Done! Done! Elapsed: 00:00:52 Reconnect Power/Cable!

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Unlocking 5190	Ryu	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	23	01-07-2018 17:14
news headlines to gsm phone	mos	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	7	05-22-2016 11:42
my 8810 is phone locked ,can somebody please help	duyphuc	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	18	12-23-2014 09:03
need software for 5161 by cable	mln2000	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	6	08-29-2010 20:17