SL45i dead - Siemens Sensor Tools Cause: Help needed - GSM-Forum

Phalanx · 08-07-2003, 15:16

Hello everyone!

My friend's phone is dead - he tried to make changes (calibrate the battery) in Siemens Sensor Tools, and f**ed it up. SST shows an error window with text: Unable to read Eelite BlockId=67 Info; ( www.darus2.republika.pl/1.jpg ) Could someone tell me, what the hell is going on? Swup, new eeprom, map doesn't make any effect.

Best regards
Phalanx

Andi_HUYVU · 08-07-2003, 15:23

I faced this problem before. This block could be corrupted. I'm sure that new EEPROM will fix the problem.

highpingbastard · 08-08-2003, 05:14

Yes...a new eeprom will fix this.
I have had this problem heaps of times.

Upload a new EEPROM, and then use KSIE to change the IMEI. If this doesn't work, then use a fullflash and change the IMEI with KSIE.

If this doesn't work then there's something much more wrong than simply a corrupted blk.

Andi_HUYVU · 08-08-2003, 05:39

I think you should backup your own EEPROM so that you don't need to write new MAP anymore.

Skydiver4o · 08-08-2003, 06:42

Hi ,
I think the problem in some of block on your eeprom compare your eeprom whit eeprom tools www.siemens-club.ru end seen block 60 to 70
BR

Phalanx · 08-08-2003, 09:23

All is now ok, thank you, guys for your help.

k1ngkong · 06-20-2004, 11:40

Hi Phalanx,

Please would you advise how you corrected the battery problem?

I have similar problem!

Cordially,
[email protected]

hellman · 06-20-2004, 13:27

Phalank my problem it's same with u....
please send me
[email protected]

SashaCZ · 06-24-2004, 13:56

I will try to answer...

To calibrate the battery you must measure the voltage of the battery with Voltmeter at 2 stages:

1) when the battery is empty.
2) when the battery is full

Then you should enter these values into the fields:

Vbatt1
Vbatt2

and then click the button: "Calculate SpgY03V and SpgY04V" and "Write Phone"

and it should be done!

You should not touch the other values as you can go out of range easily -> damages the eeprom ->

BUT I have never done this procedure as I have no problem with my batt., I only read about it in one of the Czech forums.
Perhaps in the future when I buy a stronger battery....

(I guess you could use the patch: "Drawing signal level in dB and battery level in mV" to measure the Voltage, but do not know how accurate it is)

m2myo · 06-28-2004, 00:29

Quote:

Originally Posted by SashaCZ

I will try to answer...

To calibrate the battery you must measure the voltage of the battery with Voltmeter at 2 stages:

1) when the battery is empty.
2) when the battery is full

Then you should enter these values into the fields:

Vbatt1
Vbatt2

and then click the button: "Calculate SpgY03V and SpgY04V" and "Write Phone"

and it should be done!

You should not touch the other values as you can go out of range easily -> damages the eeprom ->

BUT I have never done this procedure as I have no problem with my batt., I only read about it in one of the Czech forums.
Perhaps in the future when I buy a stronger battery....

(I guess you could use the patch: "Drawing signal level in dB and battery level in mV" to measure the Voltage, but do not know how accurate it is)

But what do we write in the

VbattDSP1
VbattDSP2 fields because in order to calculate spgy03 and 04v we need
those values too

SashaCZ · 08-02-2004, 16:14

I have found out that these two values VbattDSP1 + VbattDSP2 which are needed in order to perform the calculation are corresponding to the values Vbatt1 + Vbatt2. They should be the same except that these should be in digital form (Vbatt1 + Vbatt2 are analog values) so the phone can uderestand it (I guess that it needs to be run through phone`s A/D converter - bur still do not know how). This method of battery calibration should be similar to the one done at Siemens.

08-07-2003, 15:16	#1 (permalink)
Phalanx Junior Member Join Date: Mar 2003 Location: Gdañsk, POLAND Age: 40 Posts: 21 Member: 24832 Status: Offline Thanks Meter: 0	SL45i dead - Siemens Sensor Tools Cause: Help needed Hello everyone! My friend's phone is dead - he tried to make changes (calibrate the battery) in Siemens Sensor Tools, and f**ed it up. SST shows an error window with text: Unable to read Eelite BlockId=67 Info; ( www.darus2.republika.pl/1.jpg ) Could someone tell me, what the hell is going on? Swup, new eeprom, map doesn't make any effect. Best regards Phalanx

08-02-2004, 16:14	#11 (permalink)
SashaCZ Junior Member Join Date: Apr 2003 Location: Prague, Czech rep. Age: 45 Posts: 21 Member: 26318 Status: Offline Thanks Meter: 0	VbattDSP1 + VbattDSP2 fields I have found out that these two values VbattDSP1 + VbattDSP2 which are needed in order to perform the calculation are corresponding to the values Vbatt1 + Vbatt2. They should be the same except that these should be in digital form (Vbatt1 + Vbatt2 are analog values) so the phone can uderestand it (I guess that it needs to be run through phone`s A/D converter - bur still do not know how). This method of battery calibration should be similar to the one done at Siemens. Last edited by SashaCZ; 08-02-2004 at 17:12.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
can't use siemens sensor tool -- help :))	uimuha	Siemens-Benq Flash Patching	4	10-15-2004 06:11
SL45i DEATH WITH SENSOR TOOL !!!!	PYCON	x1x to x45/x50	2	07-17-2004 19:05
Help! Siemens sensors tool 1.3!	morzsi	x1x to x45/x50	3	11-06-2003 21:05
Siemens Sensor Tools Help - Battery empty Problem	stigma	x1x to x45/x50	4	03-15-2003 12:10
Need blk-File for Siemens Sensor Tool for SL45	vikado77	x1x to x45/x50	4	07-09-2002 22:04

08-07-2003, 15:23	#2 (permalink)
Andi_HUYVU Insane Poster Join Date: Feb 2003 Location: Saigon, Vietnam Posts: 85 Member: 22487 Status: Offline Thanks Meter: 0	I faced this problem before. This block could be corrupted. I'm sure that new EEPROM will fix the problem.

08-08-2003, 05:14	#3 (permalink)
highpingbastard Insane Poster Join Date: Jul 2003 Posts: 61 Member: 33336 Status: Offline Thanks Meter: 0	Yes...a new eeprom will fix this. I have had this problem heaps of times. Upload a new EEPROM, and then use KSIE to change the IMEI. If this doesn't work, then use a fullflash and change the IMEI with KSIE. If this doesn't work then there's something much more wrong than simply a corrupted blk.

08-08-2003, 05:39	#4 (permalink)
Andi_HUYVU Insane Poster Join Date: Feb 2003 Location: Saigon, Vietnam Posts: 85 Member: 22487 Status: Offline Thanks Meter: 0	I think you should backup your own EEPROM so that you don't need to write new MAP anymore.

08-08-2003, 06:42	#5 (permalink)
Skydiver4o Freak Poster Join Date: Mar 2003 Location: EU Posts: 140 Member: 25696 Status: Offline Thanks Meter: 0	Hi , I think the problem in some of block on your eeprom compare your eeprom whit eeprom tools www.siemens-club.ru end seen block 60 to 70 BR

08-08-2003, 09:23	#6 (permalink)
Phalanx Junior Member Join Date: Mar 2003 Location: Gdañsk, POLAND Age: 40 Posts: 21 Member: 24832 Status: Offline Thanks Meter: 0	All is now ok, thank you, guys for your help.

06-20-2004, 11:40	#7 (permalink)
k1ngkong Junior Member Join Date: Jun 2004 Age: 63 Posts: 5 Member: 69547 Status: Offline Thanks Meter: 0	Hi Phalanx, Please would you advise how you corrected the battery problem? I have similar problem! Cordially, [email protected]

06-20-2004, 13:27	#8 (permalink)
hellman Junior Member Join Date: May 2004 Age: 39 Posts: 2 Member: 66722 Status: Offline Thanks Meter: 0	Phalank my problem it's same with u.... please send me [email protected]

06-24-2004, 13:56	#9 (permalink)
SashaCZ Junior Member Join Date: Apr 2003 Location: Prague, Czech rep. Age: 45 Posts: 21 Member: 26318 Status: Offline Thanks Meter: 0	I will try to answer... To calibrate the battery you must measure the voltage of the battery with Voltmeter at 2 stages: 1) when the battery is empty. 2) when the battery is full Then you should enter these values into the fields: Vbatt1 Vbatt2 and then click the button: "Calculate SpgY03V and SpgY04V" and "Write Phone" and it should be done! You should not touch the other values as you can go out of range easily -> damages the eeprom -> BUT I have never done this procedure as I have no problem with my batt., I only read about it in one of the Czech forums. Perhaps in the future when I buy a stronger battery.... (I guess you could use the patch: "Drawing signal level in dB and battery level in mV" to measure the Voltage, but do not know how accurate it is)