a 60 test point - Page 2 - GSM-Forum

mourad_t · 07-16-2004, 18:43

Hi

I have here one MC60 version 4 (with TestPoint cutted!!!), I tried to unlock it with Freia 10 (or 15) but alaways "Phone not powered on" message! also same thing with Siemens Data Exchange, no communication!!!

So what's wrong then? (cristal near the battery jack) too? or TP cut?

Thanks!

sky master · 07-16-2004, 23:45

No, it's can't be Test point.Can be crystal or connection jack or your cable is bad?

mourad_t · 07-17-2004, 00:14

Quote:

Originally Posted by sky master

No, it's can't be Test point.Can be crystal or connection jack or your cable is bad?

Thanks for quick repaly...
My cable is ok, cause I unlocked one A60, then problem is in phone

I'll try to check it for tomorrow!
Bye ;-)

stavrosse · 07-18-2004, 14:52

hey mourad verifiy the cristal my be you break it when you openthe phone ,for me it was that the probleme.

darkeye_bob · 07-19-2004, 15:04

Siemens Data Exchange is a creap-software so ...
But, on my knowledge, the crystal have nothing to do with bad comunications.... The phone may work without him about few seconds to 1 min. The crystal is used for the internal clock and nothing else. I believe that are many newbiies on this forum, and, paradoxal, even they don't know anything about the mobiles hardware, they give some stupid advices

.

If you have bad comunication try at the first time to clean very well the bottom connector. If it don't work try to resolder the bottom connector area, and pay attention if you not having another program that it may use the same comport like Freia.
All my best !

sky master · 07-20-2004, 01:09

Quote:

Originally Posted by darkeye_bob

If you have bad comunication try at the first time to clean very well the bottom connector. If it don't work try to resolder the bottom connector area, and pay attention if you not having another program that it may use the same comport like Freia.
All my best !

What You talking about? Are YOu read all posts? Guy said that the phone was Ok,before unlock, and after cut T.P. phone is dead!
What soldering You mentioned,what another program???!!!!!
Oh my ***,do You hear Your self?
P.S What are You?Not newbiie?

darkeye_bob · 07-20-2004, 06:18

Quote:

Originally Posted by sky master

What You talking about? Are YOu read all posts? Guy said that the phone was Ok,before unlock, and after cut T.P. phone is dead!
What soldering You mentioned,what another program???!!!!!
Oh my ***,do You hear Your self?
P.S What are You?Not newbiie?

Of course I'm a newbie, I have only 8 years of experience...
So what, do you want a fight or what ?
Take it easy man. It is nothing wrong to be newbie. Everyone at one time, must to be a begginer.
I saw, many times, people that choose the hard way to resolve a problem, when the solution is very simple.

So, do you want to argue with me, or you want to help the buddy ?
You have right, I didn't read entire post, so I apologyze for this.

sky master · 07-20-2004, 15:59

I don't wana fight, never will.
Next time first read all posts,than argue!
I accept apologyze

EMAMIBEL · 07-25-2004, 20:03

hi
i help testpoint for siemens

GSM RAJ · 07-26-2004, 18:45

I had cut test point and tried to unlock but it gives error `boot file not accepted'. i tried all config.

sky master · 07-26-2004, 23:41

Quote:

Originally Posted by GSM RAJ

I had cut test point and tried to unlock but it gives error `boot file not accepted'. i tried all config.

Your test point wasn't good,try to cut litle more deeper,but just litle

Hawkarmx · 10-06-2004, 18:18

Where is located TP in A60?

Thanks

MitZu · 10-19-2004, 18:41

what`s wrong with an a 60 which is powered on..stay on..but after a little time it`s off..what problem it may have ?

rustum · 10-21-2004, 06:28

hi
mark on RTS and DTR comport selection and then try.
all the best

Dafageni · 10-25-2004, 04:03

Does anyone have a picture of the crystal we are talking about in this thread. Location please. I have bought a lot ( A LOT ) of a52 phone because I thought I made a bad cut. I also have this problem ( phone does not power on (software say so) with a m55 and a a60. PLease help and explain a bit more

07-16-2004, 18:43	#16 (permalink)
mourad_t No Life Poster Join Date: Apr 2003 Location: Algeria Age: 41 Posts: 952 Member: 26438 Status: Offline Thanks Meter: 8	MC60 no communication! Hi I have here one MC60 version 4 (with TestPoint cutted!!!), I tried to unlock it with Freia 10 (or 15) but alaways "Phone not powered on" message! also same thing with Siemens Data Exchange, no communication!!! So what's wrong then? (cristal near the battery jack) too? or TP cut? Thanks!

10-06-2004, 18:18	#27 (permalink)
Hawkarmx Junior Member Join Date: Aug 2004 Age: 52 Posts: 14 Member: 77592 Status: Offline Thanks Meter: 0	TP Diagram Where is located TP in A60? Thanks

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
dead mc 60 after flash and test point	GYZMO	E-Gold Based Phones	12	09-17-2006 19:03
v360v unlock by test point or not unlock by test point?	The Repair Shop	Smart-Clip	3	05-07-2006 21:02
How to Connect K750i Test Point & Where Is The Test Point Location	MT_LBN	Sony Ericsson	0	02-03-2006 01:24
is V600 CID49 test point the same as K608 test point !!!	the new	SonyEricsson (USB-Smart)	0	12-26-2005 12:03
Mc 60 Dead After Wrong Cut Of Test Point	GSM MIND	S-Gold Based Phones	2	10-14-2004 17:03

07-16-2004, 23:45	#17 (permalink)
sky master Freak Poster Join Date: Jul 2004 Age: 42 Posts: 103 Member: 72579 Status: Offline Thanks Meter: 1	No, it's can't be Test point.Can be crystal or connection jack or your cable is bad?

07-18-2004, 14:52	#19 (permalink)
stavrosse Freak Poster Join Date: Mar 2004 Age: 44 Posts: 262 Member: 60209 Status: Offline Thanks Meter: 0	hey mourad verifiy the cristal my be you break it when you openthe phone ,for me it was that the probleme.

07-19-2004, 15:04	#20 (permalink)
darkeye_bob Freak Poster Join Date: Feb 2003 Location: Tasmania Age: 55 Posts: 123 Member: 21408 Status: Offline Thanks Meter: 0	Siemens Data Exchange is a creap-software so ... But, on my knowledge, the crystal have nothing to do with bad comunications.... The phone may work without him about few seconds to 1 min. The crystal is used for the internal clock and nothing else. I believe that are many newbiies on this forum, and, paradoxal, even they don't know anything about the mobiles hardware, they give some stupid advices . If you have bad comunication try at the first time to clean very well the bottom connector. If it don't work try to resolder the bottom connector area, and pay attention if you not having another program that it may use the same comport like Freia. All my best !

07-20-2004, 15:59	#23 (permalink)
sky master Freak Poster Join Date: Jul 2004 Age: 42 Posts: 103 Member: 72579 Status: Offline Thanks Meter: 1	I don't wana fight, never will. Next time first read all posts,than argue! I accept apologyze

07-25-2004, 20:03	#24 (permalink)
EMAMIBEL Junior Member Join Date: May 2004 Location: iran Age: 41 Posts: 27 Member: 65772 Status: Offline Thanks Meter: 1	hi i help testpoint for siemens

07-26-2004, 18:45	#25 (permalink)
GSM RAJ No Life Poster Join Date: May 2001 Location: gujarat india Posts: 1,218 Member: 4600 Status: Offline Thanks Meter: 79	I had cut test point and tried to unlock but it gives error `boot file not accepted'. i tried all config.

10-19-2004, 18:41	#28 (permalink)
MitZu Insane Poster Join Date: Aug 2004 Age: 35 Posts: 64 Member: 76741 Status: Offline Thanks Meter: 0	what`s wrong with an a 60 which is powered on..stay on..but after a little time it`s off..what problem it may have ?

10-21-2004, 06:28	#29 (permalink)
rustum Junior Member Join Date: Jun 2004 Age: 45 Posts: 30 Member: 70391 Status: Offline Thanks Meter: 0	hi mark on RTS and DTR comport selection and then try. all the best

10-25-2004, 04:03	#30 (permalink)
Dafageni Freak Poster Join Date: May 2004 Location: South America Posts: 175 Member: 64449 Status: Offline Thanks Meter: 2	Does anyone have a picture of the crystal we are talking about in this thread. Location please. I have bought a lot ( A LOT ) of a52 phone because I thought I made a bad cut. I also have this problem ( phone does not power on (software say so) with a m55 and a a60. PLease help and explain a bit more