S8500 after boot repair with Riff Jtag Still Same - GSM-Forum

ub mobiles · 12-26-2011, 09:33

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.28, JTAG Manager Version: 1.37
Selected Resurrector: [Samsung S8500]

Connecting to the dead body...OK
Detected dead body ID: 0x1BA00477 - CORRECT!
Set I/O Voltage reads as 2.79V, TCK Frequency is 8 MHz

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

Detected an Initialized FLASH1 Chip, ID: 0x00EC/0x0050 (512MB)
Flashing the dead body...OK
Resurrection complete

All are well but my phone still dead .....

Pulka · 12-26-2011, 18:41

Hi.
Have you Download Mode,flash with Original Firmware.
If no Download Mode,then check Hardware.

Repair4u · 12-26-2011, 18:48

Check screen. Put phone in D mode connect USB and check in device manager your Phone check USB jack as well .

zorgy_1979 · 12-28-2011, 04:54

Try at first erase full flash. Than ressurect phone. It will have only boot. Than flash it buy latest firmware with boot. Than repair imei. If it will not help check hardware. At first see fash and 3d battarey contact.

R3İS · 08-30-2012, 20:59

Quote:

Originally Posted by zorgy_1979

Try at first erase full flash. Than ressurect phone. It will have only boot. Than flash it buy latest firmware with boot. Than repair imei. If it will not help check hardware. At first see fash and 3d battarey contact.

hi

download full dump and write only 8 mb and check if same again made resurrect %99 will done no need write full

12-26-2011, 09:33	#1 (permalink)
ub mobiles Freak Poster Join Date: Aug 2005 Location: Greece Age: 38 Posts: 391 Member: 173946 Status: Offline Sonork: 100.1585498 Thanks Meter: 42	S8500 after boot repair with Riff Jtag Still Same Open serial port...OK Connecting to the RIFF Box...OK Firmware Version: 1.28, JTAG Manager Version: 1.37 Selected Resurrector: [Samsung S8500] Connecting to the dead body...OK Detected dead body ID: 0x1BA00477 - CORRECT! Set I/O Voltage reads as 2.79V, TCK Frequency is 8 MHz Resurrection sequence started. Establish communication with the phone...OK Initializing internal hardware configuration...OK Uploading resurrector data into memory...OK Starting communication with resurrector...OK Detected an Initialized FLASH1 Chip, ID: 0x00EC/0x0050 (512MB) Flashing the dead body...OK Resurrection complete All are well but my phone still dead .....

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Help with 6110	paulomt1	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	2	05-25-2009 16:29
NHE_8 wont work with NHEK5689.dll v3	steve	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	0	07-23-1999 15:48
HELP: Problem with 5110	Xabi	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	1	07-16-1999 00:44
Netmonitor with FBus????	ratzfatz	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	4	06-09-1999 17:04

12-26-2011, 18:41	#2 (permalink)
Pulka Freak Poster Join Date: Jan 2009 Location: Germany/NRW Posts: 420 Member: 936229 Status: Offline Sonork: 1606911 Thanks Meter: 115	Hi. Have you Download Mode,flash with Original Firmware. If no Download Mode,then check Hardware.

12-26-2011, 18:48	#3 (permalink)
Repair4u Freak Poster Join Date: May 2006 Posts: 437 Member: 272137 Status: Offline Thanks Meter: 75	Check screen. Put phone in D mode connect USB and check in device manager your Phone check USB jack as well .

12-28-2011, 04:54	#4 (permalink)
zorgy_1979 No Life Poster Join Date: Jun 2010 Location: Russia Age: 44 Posts: 590 Member: 1331464 Status: Offline Thanks Meter: 206	Try at first erase full flash. Than ressurect phone. It will have only boot. Than flash it buy latest firmware with boot. Than repair imei. If it will not help check hardware. At first see fash and 3d battarey contact.