help with pinout for CECT KA08 mini iphone clone

[felisuki]

Originally Posted by ck32

Thanks for this topic. I am trying to make a similar cable and have understood all what you did but have one more question about the LC12 connector : I don'nt know where is the PIN 1 on this connector.

For me, viewing from the rear, the connector's pin should be like this :
____________
\1 3 5 7 9 11/
\2 4 6 8 10 12/

Anyone can confirm this ?

Thanks

Ck

http://forum.gsmhosting.com/vbb/showthread.php?t=574212

pin 1 ---Diod 4007 found in any mobile charger---- pin 1

try this, but I think this is a fake because I tested too.

If you can read the firmware, please, post a tutorial here.

[edyasia]

Hi... i have a ka08 and dissasembled original headphone... comfirmed... pin 1 is under the battery pins... confirmed with a multimeter tapping internal shields of the phone.. pin9 is gnd... 10-11-12 are L-R audio and microphone

[felisuki]

Confirmed 3,4,9 pin for flash.

I can flash the phone, but I can't read the original. Can anyone helpme??

I go to "Readback"

Start adress = 0x00000000
Length = 0x00FFFFFF

Ok.

Click on "Read back" button.

I conect the flash cable, press ON Buttom and the flastool start.

At 78% I Receive this error:



I need help.

[Umair Rashid]

@felisuki
Try once again .It should work.

[felisuki]

YES !!!

I read the firmware setting the speed to 57600 baud.

It's too slow, 1 hour, but its Ok.

Thanks to all !!!

[ColonelZap]

Congrats

Are you going to post your firmware, please

[yanivbh1]

can anyone uplode hebrew flash file for this phone
thanks yaniv

[filippo222]

I have a CETC KA08 and the pinout is different

1=n.c. (not conn.)
2=5v from charger or usb red cable
3=?nc
4= green cable usb
5= white cable usb
6=? nc (tx serial port?)
7=?nc (rx serial port?)
8= gnd
9= left headphone
10=gnd headphone
11=right headphone
12= mic

What are the pin serial cable?please helpme!

[felisuki]

Try this.

3-tx
4-rx
9gnd

only change 3rx-4tx / 3tx-4rx

[filippo222]

i have found the pinouts :
1 nc
2 5v charger
3 nc
4 green usb
5 white usb
6 tx serial
7 rx serial
8 gnd for charger,usb and serial?
9 left headphone
10 gnd headphone and mic
11 right headphone
12 mic

but my mini ka08 is a clone?
the firmware is
MAUI.07B.W08.16.MPV4.F1
BRANCH:07B
L01_GEMINI_07B
BUILD:BUILD_NO
SERIAL#:
MT012345678901234567
10
BUILD TIME
2009/04/16 16:49
the colours of the battery is gold 1380 ma h
i have formatted with mtk tools and spiderman but not work
because i not know begin and format lengt i have format auto
i'm very stupid ,i make backup but not work

i need the complete firmware because i have format all
please contact me if is possible reanimate the phone
i'm italian and i apologize for my bad english

my email is [email protected]

[vipeppebo]

Hello everyone, how can I change the USB cable?? what pins should I put?

[aaaaaaaa]

ka08 pinouts on motherboard . tested with infinity box

[bbbbbb]

Hi,

I also have KA08 and the folowing is the pinout I have:
1 - +5V
2 - ?
3 - GND
4 - ?
5 - ?
6 - ?
7 - White USB
8 - Green USB
9 - GND
10 - Left/Right Headphone
11 - Left/Right Headphone
12 - MIC +

What pin is rx/tx?
thanks.

[bbbbbb]

It seems that I have AK08 phone (but was sold as KA08) pinout is :
1 - +5V Charge
2 - +VBAT
3 - GND
4 - to Tx
5 - to Rx
6 - ?
7 - White USB
8 - Green USB
9 - GND
10 - Left/Right Headphone
11 - Left/Right Headphone
12 - MIC +