*** Cyclone Box and VPP thing *** - Page 4 - GSM-Forum

LIEREN · 06-24-2009, 22:51

＠Cyclonebox
thank.......you

MiH · 06-25-2009, 08:17

My PCB layout is in picture bellow.

multimedia · 06-25-2009, 10:03

Quote:

Originally Posted by MiH

In schematic below is Vpp voltage generator from
5V input (USB) voltage. Output stabilised voltage
9,75V / 100mA is connected to "external power input
connector". Idle power current is only 6mA.

Almost all needed components to build a generator is
used from low cost common 12V car mobile phone charger
(IC,diode, capacitors, resistors).

Generator is fitted inside cyclone box and is connected
via 3 wires (input 5V usb, GND, output Vpp)

Parameters:
Input voltage : 3,0 - 7,5V
Output volage : 9,75V (+/- 10mV, adjusted by R1/R2)
Efficency : 89%
Idle curent : 6 mA
Max. out curent : 100 mA (adjusted by R4)

you are very attentive it's great trick !

randy_d4 · 06-26-2009, 11:17

@Cyclonebox

What about my problem here and here?One month without clear answer!!Do U actually know how many pcb revision is made for your CODE? Why mine pcb(and mine's friend also) are with low power voltage regulators?

Pls as u may know hardware is also so important as software!!

Pls take a time to answer me this time!

ptt · 06-26-2009, 22:38

The box has 6 month warranty... contact your reseller....

BR

Qaisar Mahmood · 06-27-2009, 13:33

Card Firmware Revision: 0109
Card is activated
Box is activated
Started box selftests procedure
USB Voltage 5.03v PASSED
MCU Voltage 3.29v PASSED
Core Voltage 1.82v PASSED
VBAT Voltage 0.01v PASSED
VBAT Voltage 4.97v PASSED
Box VPP disabled
VPP Voltage 0.00v PASSED
Internal Box VPP Enabled
VPP Voltage 4.92v PASSED
Box VPP disabled
VPP Voltage 0.04v PASSED
External Box VPP Enabled
VPP Voltage 8.33v PASSED
Box VPP disabled
All box selftests passed!
Initializing FBUS...
All initialized - Ready to work

hazar · 06-27-2009, 17:18

I'm use AC ADAPTOR of Smart-Clip 9v -500mA

VPP Voltage 0.04v FAILED - IGNORED - Probably power supply is not connected

problem ...ich spreche turkisch help

backbiter17 · 06-27-2009, 21:50

you should use DC power supply

br,A

vanus2 · 06-28-2009, 09:14

hi all! if i open my box to modify will i lose waranty?

jubillee · 06-28-2009, 10:16

please help me after commanding erase all chips 1202 with cyclone now contact service and when i flash it remains the same

jubillee · 06-28-2009, 10:22

please help me after commanding erase all chips 1202 with cyclone now contact service and when i flash it remains the same

ivanx · 06-28-2009, 22:00

Quote:

Originally Posted by hazar

I'm use AC ADAPTOR of Smart-Clip 9v -500mA

VPP Voltage 0.04v FAILED - IGNORED - Probably power supply is not connected

problem ...ich spreche turkisch help

i have the same problem,then i use use fully stabilised 9.5v DC supply

this is how i solve my problem.

.::TR_LAZ::. · 06-29-2009, 16:04

thanks ...

Cyclonebox

Nokia DCT4/WD2/BB5 Service Tool Initialization Started, Engine Revision: 1.0.0.7828
Handling device: [Cyclone Team], [Cyclone Bootloader]
Handling device: [Cyclone Team], [Cyclone Box]
Initializing box...
Box Firmware: Cyclone Nokia Application v1.05, (Jun 22 2009 12:23:29, gcc-4.2.2, RTOS v5.2.0), Type: Signed Production Application, Flags: CONST-TX2-PIN ; VISTA-SUPPORT ; BB5-NCK-CALC
Box Serial Number: C0000EB0
HW Revision: A, Suitable for: Production, Case: First Plastic Case, MCU Manufacture Time: 2009, wk01 / wk06
Initializing security card...
Card Serial Number:********
Card Firmware Revision: 0****
Card is activated
Box is activated
Started box selftests procedure
USB Voltage 5,06v PASSED
MCU Voltage 3,30v PASSED
Core Voltage 1,76v PASSED
VBAT Voltage 0,68v PASSED
VBAT Voltage 5,02v PASSED
Box VPP disabled
VPP Voltage 0,04v PASSED
Internal Box VPP Enabled
VPP Voltage 4,92v PASSED
Box VPP disabled
VPP Voltage 0,04v PASSED
External Box VPP Enabled
VPP Voltage 0,04v FAILED - IGNORED - Probably power supply is not connected
Box VPP disabled
All box selftests passed!
Initializing FBUS...
All initialized - Ready to work
Scanning avaiable products...
Processing C:\Program Files\Nokia\Phoenix\Products\...
Found 89 products, Filtering DCT4 Products - wait...
11 Products left after filtering. Ready.
Retrieving Variants for Product RM-298 - wait...
253 Variants Retrieved
Processing pre-flash tasks...
Backing up Flash IMEI...
RPL is Stored in PM...
Flash IMEI Backup OK
Pre-flash tasks finished
Booting UPP...
UPP ID: 3162 [HW_UNKNOWN]
rm298__05.20.mcusw, Type: Flash Image, Algo: DCT4, DCT4 ALGORITHM
Flashbus Write baud set to 100Kbits
u3_2nd.fia, Type: 2nd Boot Loader, Rev: 7.4.77.0, Algo: DCT4
Box VPP disabled
Internal Phone VPP Selected
PLL Factor: 3
FlashChip[0]: 0x0020881C @ 0x01000000, ST, SectorSize: 128kB, Ext: 00009221
FlashChip[1]: 0x0020881C @ 0x02000000, ST, SectorSize: 128kB, Ext: 00009221
Signature: AD7EB61A1BBE0BE27D586BE4DBEE6514
Flashbus Write baud set to 1.0Mbits
Flashbus Read baud set to 51Kbits
u3_intel.fia, Type: Algorithm, Target: FlashChip[0] 0x0020881C (256Mbits), Rev: 7.4.77.0, Algo: DCT4 ALGORITHM
Nominal VPP Voltage: 9V, Detected: 0,04V
MSID-Crypted: 84755AE59ED3765A7DD7AAE595
MSID-Plain: 2C40BAE9005F3C7CA8000000
FAID-Crypted: 7CB36FEE212661031CCB4781
Flashbus Write baud set to 6.50Mbits
2 Region(s) to erase
Erasing NOR Region [0x01000000-0x0101FFFF]
Erasing NOR Region [0x01020000-0x01C3FFFF]
Erase taken 58.374s
Writing 343 blocks...
All blocks written OK! Time taken 520.939s
Terminating flash session
Box VPP disabled
Booting UPP...
UPP ID: 3162 [HW_UNKNOWN]
rm298__05.20.image_ad, Type: Flash Image, Algo: DCT4, DCT4 ALGORITHM
Flashbus Write baud set to 100Kbits
u3_2nd.fia, Type: 2nd Boot Loader, Rev: 7.4.77.0, Algo: DCT4
Box VPP disabled
Internal Phone VPP Selected
PLL Factor: 3
FlashChip[0]: 0x0020881C @ 0x01000000, ST, SectorSize: 128kB, Ext: 00009221
FlashChip[1]: 0x0020881C @ 0x02000000, ST, SectorSize: 128kB, Ext: 00009221
Signature: AD7EB61A1BBE0BE27D586BE4DBEE6514
Flashbus Write baud set to 1.0Mbits
Flashbus Read baud set to 51Kbits
u3_intel.fia, Type: Algorithm, Target: FlashChip[0] 0x0020881C (256Mbits), Rev: 7.4.77.0, Algo: DCT4 ALGORITHM
Nominal VPP Voltage: 9V, Detected: 0,04V
MSID-Crypted: 84B11141F88AB54AACEEA9F6CA
MSID-Plain: D26EBAF1005F3C7CAA000610
FAID-Crypted: 5CE5BF18186A73C7DD575DB2
Flashbus Write baud set to 6.50Mbits
2 Region(s) to erase
Erasing NOR Region [0x02000000-0x02DBFFFF]
Erasing NOR Region [0x02DC0000-0x02F9FFFF]
Erase taken 73.366s
File Sector Size: 128kB, Flash Chip Sector Size: 128kB
CNT Convertion not needed
Writing 264 blocks...
All blocks written OK! Time taken 180.730s
Terminating flash session
Extracting Content Package...
CP Extract Failed -> CP Server not exists
WARNING: Failed to extract CP
Box VPP disabled
Booting UPP...
UPP ID: 3162 [HW_UNKNOWN]
rm298__05.20.ppm_ad, Type: Flash Image, Algo: DCT4, DCT4 ALGORITHM
Flashbus Write baud set to 100Kbits
u3_2nd.fia, Type: 2nd Boot Loader, Rev: 7.4.77.0, Algo: DCT4
Box VPP disabled
Internal Phone VPP Selected
PLL Factor: 3
FlashChip[0]: 0x0020881C @ 0x01000000, ST, SectorSize: 128kB, Ext: 00009221
FlashChip[1]: 0x0020881C @ 0x02000000, ST, SectorSize: 128kB, Ext: 00009221
Signature: AD7EB61A1BBE0BE27D586BE4DBEE6514
Flashbus Write baud set to 1.0Mbits
Flashbus Read baud set to 51Kbits
u3_intel.fia, Type: Algorithm, Target: FlashChip[0] 0x0020881C (256Mbits), Rev: 7.4.77.0, Algo: DCT4 ALGORITHM
Nominal VPP Voltage: 9V, Detected: 0,04V
MSID-Crypted: 845A5365690DD0D51BD79257AC
MSID-Plain: 3E4EBAE9005F3C7CA9000000
FAID-Crypted: 423F9B1C582E13025B4065C6
Flashbus Write baud set to 6.50Mbits
1 Region(s) to erase
Erasing NOR Region [0x01C40000-0x01FFFFFF]
Erase taken 17.64s
Writing 88 blocks...
All blocks written OK! Time taken 129.687s
Terminating flash session
Box VPP disabled
Processing post-flash tasks...
Unlocking...
MCU Version V 05.20
MCU Date 06-12-07
Product RM-298
Manufacturer (c) Nokia
IMEI 359**********
Mastercode 373111***
Asic 11
HW Signature 8089070BDFCD66CC
Simlock Server SIMLOCK SERVER
Simlock Key 0010100000000000
Simlock Profile 800000000001000B
Simlock Aux 000B5555
Simlock IMEI 0055***60*****6187300
Simlock Key Cnt 0
Simlock FBUS Cnt 0
Simlock [1,1] State: OPENED Type: MCC-MNC Data: FFFFFF
Simlock [1,2] State: OPENED Type: GID Data: FFFF
Simlock [1,3] State: OPENED Type: GID Data: FFFF
Simlock [1,4] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF
Simlock [1,5] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF
Simlock [2,1] State: OPENED Type: MCC-MNC Data: FFFFFF
Simlock [2,2] State: OPENED Type: GID Data: FFFF
Simlock [2,3] State: OPENED Type: GID Data: FFFF
Simlock [2,4] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF
Simlock [2,5] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF
Simlock [3,1] State: OPENED Type: MCC-MNC Data: FFFFFF
Simlock [3,2] State: OPENED Type: GID Data: FFFF
Simlock [3,3] State: OPENED Type: GID Data: FFFF
Simlock [3,4] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF
Simlock [3,5] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF
Simlock [4,1] State: OPENED Type: MCC-MNC Data: FFFFFF
Simlock [4,2] State: OPENED Type: GID Data: FFFF
Simlock [4,3] State: OPENED Type: GID Data: FFFF
Simlock [4,4] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF
Simlock [4,5] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF
Simlock [5,1] State: OPENED Type: MCC-MNC Data: FFFFFF
Simlock [5,2] State: OPENED Type: GID Data: FFFF
Simlock [5,3] State: OPENED Type: GID Data: FFFF
Simlock [5,4] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF
Simlock [5,5] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF
Simlock [6,1] State: OPENED Type: MCC-MNC Data: FFFFFF
Simlock [6,2] State: OPENED Type: GID Data: FFFF
Simlock [6,3] State: OPENED Type: GID Data: FFFF
Simlock [6,4] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF
Simlock [6,5] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF
Simlock [7,1] State: OPENED Type: MCC-MNC Data: FFFFFF
Simlock [7,2] State: OPENED Type: GID Data: FFFF
Simlock [7,3] State: OPENED Type: GID Data: FFFF
Simlock [7,4] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF
Simlock [7,5] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF
Selecting unlock method...
Search in: C:\Program Files\Cyclone Box\UnlockData\
Searching for: RM-298_V 05.20.unlock_img
Asking card to sign HW Signature...
Signed OK (958A4985260507079CD699D88604D48D3C45D6C5)
Writing patch file...
Booting UPP...
UPP ID: 3162 [HW_UNKNOWN]
shadow, Type: Flash Image, Algo: DCT4, DCT4 ALGORITHM
Flashbus Write baud set to 100Kbits
u3_2nd.fia, Type: 2nd Boot Loader, Rev: 7.4.77.0, Algo: DCT4
Box VPP disabled
Internal Phone VPP Selected
PLL Factor: 3
FlashChip[0]: 0x0020881C @ 0x01000000, ST, SectorSize: 128kB, Ext: 00009221
FlashChip[1]: 0x0020881C @ 0x02000000, ST, SectorSize: 128kB, Ext: 00009221
Signature: AD7EB61A1BBE0BE27D586BE4DBEE6514
Flashbus Write baud set to 1.0Mbits
Flashbus Read baud set to 51Kbits
u3_intel.fia, Type: Algorithm, Target: FlashChip[0] 0x0020881C (256Mbits), Rev: 7.4.77.0, Algo: DCT4 ALGORITHM
Nominal VPP Voltage: 9V, Detected: 0,04V
MSID-Crypted: 84755AE59ED3765A7DD7AAE595
Using MSID-FAID Cache, Not wasting card
FAID-Crypted: 7CB36FEE212661031CCB4781
Flashbus Write baud set to 6.50Mbits
2 Region(s) to erase
Erasing NOR Region [0x01000000-0x0101FFFF]
Erasing NOR Region [0x01080000-0x0109FFFF]
Erase taken 1.222s
Writing 10 blocks...
All blocks written OK! Time taken 12.227s
Terminating flash session
Box VPP disabled
Simlock Security - NOT TAMPERED
Saving Simlock to "RM-298_3595********_29.06.2009_175612.Unlock.PM"
Writing SP...
New SP Accepted OK!
Phone unlocked OK!
Unlock thread finished, continuing...
Post-flash tasks finished...
Flash successfully finished!

iwan8818 · 07-05-2009, 02:43

Quote:

Originally Posted by honyjee

can we use external adopter to box on socket (AC adopter)

yes can, search this power supply,
or u can use cpf box power supply..

input :100-240-50hz, 0.4A

output : +9 --- 2A

Card is activated
Box is activated
Started box selftests procedure
USB Voltage 5.05v PASSED
MCU Voltage 3.27v PASSED
Core Voltage 1.79v PASSED
VBAT Voltage 0.01v PASSED
VBAT Voltage 4.90v PASSED
Box VPP disabled
VPP Voltage 0.02v PASSED
Internal Box VPP Enabled
VPP Voltage 4.92v PASSED
Box VPP disabled
VPP Voltage 0.00v PASSED
External Box VPP Enabled
VPP Voltage 8.60v PASSED
Box VPP disabled
All box selftests passed!
Initializing FBUS...
All initialized - Ready to work

Hady_e02@yahoo · 07-05-2009, 19:34

Quote:

Originally Posted by iwan8818

yes can, search this power supply,
or u can use cpf box power supply..

input :100-240-50hz, 0.4A

output : +9 --- 2A

Card is activated
Box is activated
Started box selftests procedure
USB Voltage 5.05v PASSED
MCU Voltage 3.27v PASSED
Core Voltage 1.79v PASSED
VBAT Voltage 0.01v PASSED
VBAT Voltage 4.90v PASSED
Box VPP disabled
VPP Voltage 0.02v PASSED
Internal Box VPP Enabled
VPP Voltage 4.92v PASSED
Box VPP disabled
VPP Voltage 0.00v PASSED
External Box VPP Enabled
VPP Voltage 8.60v PASSED
Box VPP disabled
All box selftests passed!
Initializing FBUS...
All initialized - Ready to work

i hv used cpf adaptor..but it's failed selftest vpp...i just hv many2 question about this matter...
1.should we make this jumper of R53?why shall it happen if we do jumper or not?wht's the influence to the tx line?why do supporter say why must deliver it on service pin 10?
2.according to the pic,shall we remove 2 capasitors?if not wht's the problem?
3.why do the factory put the resistor before release to the market..why should we as user must do it?do u know that we can loose our warranty??

i hv jumpered the resistor n plug cpf adaptor..but it's still failed on selftest vpp external..should we jumper it if we want to use vpp external??please somebody help me to explain all my questions..also give me detail in explaination about vpp service pin...coz supporter not give detail manual n explanation..surely many peoples r confused...hopes someone there will clear all this matter..really thx for this kind person

06-26-2009, 11:17	#49 (permalink)
randy_d4 Freak Poster Join Date: Jul 2004 Location: 0xDEADBEEF Age: 42 Posts: 479 Member: 71246 Status: Offline Thanks Meter: 40	@Cyclonebox What about my problem here and here?One month without clear answer!!Do U actually know how many pcb revision is made for your CODE? Why mine pcb(and mine's friend also) are with low power voltage regulators?Pls as u may know hardware is also so important as software!! Pls take a time to answer me this time!

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
MXKey, PolarBox2, Infinity Box, Z3X, Cyclone Box And Many More Inside This Box	shahzaadbutt	Main Sales Section	0	03-27-2010 07:33
MXKey, Infinity Box, Z3X, Cyclone Box And Many More Inside This Box	shahzaadbutt	Main Sales Section	0	02-24-2010 10:51
Bomb!!Bomb!!Wifi box ,Cyclone box and Mx key dongle all is in good price	lotusgsm.com	Main Sales Section	0	01-19-2010 10:04
Hi siroya nadeem gondal cyclone box and new product supporter	AY29!4LYF	Cyclonebox	0	07-15-2009 17:47
How is cyclone box and who is behind this project?	Mr.3.	Off Topic Zone	0	03-19-2009 04:37

06-24-2009, 22:51	#46 (permalink)
LIEREN No Life Poster Join Date: Dec 2008 Location: iCloud ID Removed Service Posts: 1,268 Member: 917576 Status: Offline Sonork: QQ:366688456 Thanks Meter: 533	＠Cyclonebox thank.......you

06-26-2009, 22:38	#50 (permalink)
ptt No Life Poster Join Date: Sep 2006 Location: RETIRED ! Age: 47 Posts: 3,327 Member: 348680 Status: Offline Thanks Meter: 1,273	The box has 6 month warranty... contact your reseller.... BR

06-27-2009, 13:33	#51 (permalink)
Qaisar Mahmood No Life Poster Join Date: Jan 2006 Location: Pakistan Posts: 15,094 Member: 226457 Status: Offline Sonork: No more used Thanks Meter: 14,934	Card Firmware Revision: 0109 Card is activated Box is activated Started box selftests procedure USB Voltage 5.03v PASSED MCU Voltage 3.29v PASSED Core Voltage 1.82v PASSED VBAT Voltage 0.01v PASSED VBAT Voltage 4.97v PASSED Box VPP disabled VPP Voltage 0.00v PASSED Internal Box VPP Enabled VPP Voltage 4.92v PASSED Box VPP disabled VPP Voltage 0.04v PASSED External Box VPP Enabled VPP Voltage 8.33v PASSED Box VPP disabled All box selftests passed! Initializing FBUS... All initialized - Ready to work

06-27-2009, 17:18	#52 (permalink)
hazar Freak Poster Join Date: Aug 2007 Posts: 456 Member: 565487 Status: Offline Sonork: 100.1590618 Thanks Meter: 35	I'm use AC ADAPTOR of Smart-Clip 9v -500mA VPP Voltage 0.04v FAILED - IGNORED - Probably power supply is not connected problem ...ich spreche turkisch help

06-27-2009, 21:50	#53 (permalink)
backbiter17 No Life Poster Join Date: Jan 2004 Location: SLOVENIA, LJUBLJANA Age: 55 Posts: 1,155 Member: 48933 Status: Offline Thanks Meter: 104	you should use DC power supply br,A

06-28-2009, 09:14	#54 (permalink)
vanus2 Junior Member Join Date: Nov 2007 Posts: 25 Member: 624576 Status: Offline Thanks Meter: 6	hi all! if i open my box to modify will i lose waranty?

06-28-2009, 10:16	#55 (permalink)
jubillee Freak Poster Join Date: Nov 2008 Location: uganda Age: 50 Posts: 484 Member: 894224 Status: Offline Thanks Meter: 96	please help me after commanding erase all chips 1202 with cyclone now contact service and when i flash it remains the same

06-28-2009, 10:22	#56 (permalink)
jubillee Freak Poster Join Date: Nov 2008 Location: uganda Age: 50 Posts: 484 Member: 894224 Status: Offline Thanks Meter: 96	please help me after commanding erase all chips 1202 with cyclone now contact service and when i flash it remains the same

06-29-2009, 16:04	#58 (permalink)
.::TR_LAZ::. No Life Poster Join Date: Sep 2005 Location: TR-LAZ Posts: 822 Member: 178227 Status: Offline Sonork: 100.1597371 Thanks Meter: 176	thanks ... Cyclonebox Nokia DCT4/WD2/BB5 Service Tool Initialization Started, Engine Revision: 1.0.0.7828 Handling device: [Cyclone Team], [Cyclone Bootloader] Handling device: [Cyclone Team], [Cyclone Box] Initializing box... Box Firmware: Cyclone Nokia Application v1.05, (Jun 22 2009 12:23:29, gcc-4.2.2, RTOS v5.2.0), Type: Signed Production Application, Flags: CONST-TX2-PIN ; VISTA-SUPPORT ; BB5-NCK-CALC Box Serial Number: C0000EB0 HW Revision: A, Suitable for: Production, Case: First Plastic Case, MCU Manufacture Time: 2009, wk01 / wk06 Initializing security card... Card Serial Number:****** Card Firmware Revision: 0 Card is activated Box is activated Started box selftests procedure USB Voltage 5,06v PASSED MCU Voltage 3,30v PASSED Core Voltage 1,76v PASSED VBAT Voltage 0,68v PASSED VBAT Voltage 5,02v PASSED Box VPP disabled VPP Voltage 0,04v PASSED Internal Box VPP Enabled VPP Voltage 4,92v PASSED Box VPP disabled VPP Voltage 0,04v PASSED External Box VPP Enabled VPP Voltage 0,04v FAILED - IGNORED - Probably power supply is not connected Box VPP disabled All box selftests passed! Initializing FBUS... All initialized - Ready to work Scanning avaiable products... Processing C:\Program Files\Nokia\Phoenix\Products\... Found 89 products, Filtering DCT4 Products - wait... 11 Products left after filtering. Ready. Retrieving Variants for Product RM-298 - wait... 253 Variants Retrieved Processing pre-flash tasks... Backing up Flash IMEI... RPL is Stored in PM... Flash IMEI Backup OK Pre-flash tasks finished Booting UPP... UPP ID: 3162 [HW_UNKNOWN] rm298__05.20.mcusw, Type: Flash Image, Algo: DCT4, DCT4 ALGORITHM Flashbus Write baud set to 100Kbits u3_2nd.fia, Type: 2nd Boot Loader, Rev: 7.4.77.0, Algo: DCT4 Box VPP disabled Internal Phone VPP Selected PLL Factor: 3 FlashChip[0]: 0x0020881C @ 0x01000000, ST, SectorSize: 128kB, Ext: 00009221 FlashChip[1]: 0x0020881C @ 0x02000000, ST, SectorSize: 128kB, Ext: 00009221 Signature: AD7EB61A1BBE0BE27D586BE4DBEE6514 Flashbus Write baud set to 1.0Mbits Flashbus Read baud set to 51Kbits u3_intel.fia, Type: Algorithm, Target: FlashChip[0] 0x0020881C (256Mbits), Rev: 7.4.77.0, Algo: DCT4 ALGORITHM Nominal VPP Voltage: 9V, Detected: 0,04V MSID-Crypted: 84755AE59ED3765A7DD7AAE595 MSID-Plain: 2C40BAE9005F3C7CA8000000 FAID-Crypted: 7CB36FEE212661031CCB4781 Flashbus Write baud set to 6.50Mbits 2 Region(s) to erase Erasing NOR Region [0x01000000-0x0101FFFF] Erasing NOR Region [0x01020000-0x01C3FFFF] Erase taken 58.374s Writing 343 blocks... All blocks written OK! Time taken 520.939s Terminating flash session Box VPP disabled Booting UPP... UPP ID: 3162 [HW_UNKNOWN] rm298__05.20.image_ad, Type: Flash Image, Algo: DCT4, DCT4 ALGORITHM Flashbus Write baud set to 100Kbits u3_2nd.fia, Type: 2nd Boot Loader, Rev: 7.4.77.0, Algo: DCT4 Box VPP disabled Internal Phone VPP Selected PLL Factor: 3 FlashChip[0]: 0x0020881C @ 0x01000000, ST, SectorSize: 128kB, Ext: 00009221 FlashChip[1]: 0x0020881C @ 0x02000000, ST, SectorSize: 128kB, Ext: 00009221 Signature: AD7EB61A1BBE0BE27D586BE4DBEE6514 Flashbus Write baud set to 1.0Mbits Flashbus Read baud set to 51Kbits u3_intel.fia, Type: Algorithm, Target: FlashChip[0] 0x0020881C (256Mbits), Rev: 7.4.77.0, Algo: DCT4 ALGORITHM Nominal VPP Voltage: 9V, Detected: 0,04V MSID-Crypted: 84B11141F88AB54AACEEA9F6CA MSID-Plain: D26EBAF1005F3C7CAA000610 FAID-Crypted: 5CE5BF18186A73C7DD575DB2 Flashbus Write baud set to 6.50Mbits 2 Region(s) to erase Erasing NOR Region [0x02000000-0x02DBFFFF] Erasing NOR Region [0x02DC0000-0x02F9FFFF] Erase taken 73.366s File Sector Size: 128kB, Flash Chip Sector Size: 128kB CNT Convertion not needed Writing 264 blocks... All blocks written OK! Time taken 180.730s Terminating flash session Extracting Content Package... CP Extract Failed -> CP Server not exists WARNING: Failed to extract CP Box VPP disabled Booting UPP... UPP ID: 3162 [HW_UNKNOWN] rm298__05.20.ppm_ad, Type: Flash Image, Algo: DCT4, DCT4 ALGORITHM Flashbus Write baud set to 100Kbits u3_2nd.fia, Type: 2nd Boot Loader, Rev: 7.4.77.0, Algo: DCT4 Box VPP disabled Internal Phone VPP Selected PLL Factor: 3 FlashChip[0]: 0x0020881C @ 0x01000000, ST, SectorSize: 128kB, Ext: 00009221 FlashChip[1]: 0x0020881C @ 0x02000000, ST, SectorSize: 128kB, Ext: 00009221 Signature: AD7EB61A1BBE0BE27D586BE4DBEE6514 Flashbus Write baud set to 1.0Mbits Flashbus Read baud set to 51Kbits u3_intel.fia, Type: Algorithm, Target: FlashChip[0] 0x0020881C (256Mbits), Rev: 7.4.77.0, Algo: DCT4 ALGORITHM Nominal VPP Voltage: 9V, Detected: 0,04V MSID-Crypted: 845A5365690DD0D51BD79257AC MSID-Plain: 3E4EBAE9005F3C7CA9000000 FAID-Crypted: 423F9B1C582E13025B4065C6 Flashbus Write baud set to 6.50Mbits 1 Region(s) to erase Erasing NOR Region [0x01C40000-0x01FFFFFF] Erase taken 17.64s Writing 88 blocks... All blocks written OK! Time taken 129.687s Terminating flash session Box VPP disabled Processing post-flash tasks... Unlocking... MCU Version V 05.20 MCU Date 06-12-07 Product RM-298 Manufacturer (c) Nokia IMEI 359****** Mastercode 373111* Asic 11 HW Signature 8089070BDFCD66CC Simlock Server SIMLOCK SERVER Simlock Key 0010100000000000 Simlock Profile 800000000001000B Simlock Aux 000B5555 Simlock IMEI 0055*60*6187300 Simlock Key Cnt 0 Simlock FBUS Cnt 0 Simlock [1,1] State: OPENED Type: MCC-MNC Data: FFFFFF Simlock [1,2] State: OPENED Type: GID Data: FFFF Simlock [1,3] State: OPENED Type: GID Data: FFFF Simlock [1,4] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF Simlock [1,5] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF Simlock [2,1] State: OPENED Type: MCC-MNC Data: FFFFFF Simlock [2,2] State: OPENED Type: GID Data: FFFF Simlock [2,3] State: OPENED Type: GID Data: FFFF Simlock [2,4] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF Simlock [2,5] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF Simlock [3,1] State: OPENED Type: MCC-MNC Data: FFFFFF Simlock [3,2] State: OPENED Type: GID Data: FFFF Simlock [3,3] State: OPENED Type: GID Data: FFFF Simlock [3,4] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF Simlock [3,5] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF Simlock [4,1] State: OPENED Type: MCC-MNC Data: FFFFFF Simlock [4,2] State: OPENED Type: GID Data: FFFF Simlock [4,3] State: OPENED Type: GID Data: FFFF Simlock [4,4] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF Simlock [4,5] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF Simlock [5,1] State: OPENED Type: MCC-MNC Data: FFFFFF Simlock [5,2] State: OPENED Type: GID Data: FFFF Simlock [5,3] State: OPENED Type: GID Data: FFFF Simlock [5,4] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF Simlock [5,5] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF Simlock [6,1] State: OPENED Type: MCC-MNC Data: FFFFFF Simlock [6,2] State: OPENED Type: GID Data: FFFF Simlock [6,3] State: OPENED Type: GID Data: FFFF Simlock [6,4] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF Simlock [6,5] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF Simlock [7,1] State: OPENED Type: MCC-MNC Data: FFFFFF Simlock [7,2] State: OPENED Type: GID Data: FFFF Simlock [7,3] State: OPENED Type: GID Data: FFFF Simlock [7,4] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF Simlock [7,5] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF Selecting unlock method... Search in: C:\Program Files\Cyclone Box\UnlockData\ Searching for: RM-298_V 05.20.unlock_img Asking card to sign HW Signature... Signed OK (958A4985260507079CD699D88604D48D3C45D6C5) Writing patch file... Booting UPP... UPP ID: 3162 [HW_UNKNOWN] shadow, Type: Flash Image, Algo: DCT4, DCT4 ALGORITHM Flashbus Write baud set to 100Kbits u3_2nd.fia, Type: 2nd Boot Loader, Rev: 7.4.77.0, Algo: DCT4 Box VPP disabled Internal Phone VPP Selected PLL Factor: 3 FlashChip[0]: 0x0020881C @ 0x01000000, ST, SectorSize: 128kB, Ext: 00009221 FlashChip[1]: 0x0020881C @ 0x02000000, ST, SectorSize: 128kB, Ext: 00009221 Signature: AD7EB61A1BBE0BE27D586BE4DBEE6514 Flashbus Write baud set to 1.0Mbits Flashbus Read baud set to 51Kbits u3_intel.fia, Type: Algorithm, Target: FlashChip[0] 0x0020881C (256Mbits), Rev: 7.4.77.0, Algo: DCT4 ALGORITHM Nominal VPP Voltage: 9V, Detected: 0,04V MSID-Crypted: 84755AE59ED3765A7DD7AAE595 Using MSID-FAID Cache, Not wasting card FAID-Crypted: 7CB36FEE212661031CCB4781 Flashbus Write baud set to 6.50Mbits 2 Region(s) to erase Erasing NOR Region [0x01000000-0x0101FFFF] Erasing NOR Region [0x01080000-0x0109FFFF] Erase taken 1.222s Writing 10 blocks... All blocks written OK! Time taken 12.227s Terminating flash session Box VPP disabled Simlock Security - NOT TAMPERED Saving Simlock to "RM-298_3595******_29.06.2009_175612.Unlock.PM" Writing SP... New SP Accepted OK! Phone unlocked OK! Unlock thread finished, continuing... Post-flash tasks finished... Flash successfully finished!