*** Failed to write CMT cert data (3), Programming Status Error ***

[moulnisky]

And check your cables as well.. UFS don't use the TX2 line so is not a quality test at all

BR

Alex

[matchbox18]

why after all the i flash bb5 phone imei it be come 1234...............?

[Formingus]

I Have yellow Adapter and Still i get Error While Reading RPL from Phone
That's because as Karwos Says its APE, After i uptick TX2 RPL read ok

RPL Creation started...
Processing CMT Part...
Storing Product Code...
Storing PSN...
Storing HWID...
Simlock Store not supported, not a PA_SL2 Phone
WMDRM Store not supported
Reading Security Block...
Security block OK and saved to "RM-84_358637017127629_5232013_91435 PM.SecurityBlock.PM"
"11B0010DBB245F51310C6D9024F69EC7E42DB5BE.C0002D98 " Exists, That is good...
Storing Additional Data...
Checking Superdongle Key...
Encrypting Superdongle Key...
Storing Superdongle Key...
Checking CMLA Key...
CMLA Key Store Problem -> Failed to decode Security Section, Box Reported: Security Section Not Found (SL3 phone?)
Booting CMT...
APE_SYSTEM_ASIC_ID: 17100701
APE_ASIC_MODE_ID: 00
APE_PUBLIC_ID: 72E35E44CAF6BADB549F072AE90C3192D38A3052
APE_ROOT_KEY_HASH: 2C05369F57CC3C4CF9E783E83D9B512B00000000
APE_BOOT_ROM_CRC: AB5E4ADB
APE_SECURE_ROM_CRC: 27A06946
CMT_SYSTEM_ASIC_ID: 000000010000022600010006000C192101002200
CMT_EM_ASIC_ID: 00000232
CMT_EM_ASIC_ID: 00000353
CMT_PUBLIC_ID: 11B0010DBB245F51310C6D9024F69EC7E42DB5BE
CMT_ASIC_MODE_ID: 00
CMT_ROOT_KEY_HASH: E9EFF4BFAA5393217CA6B17755FC3E14
CMT_BOOT_ROM_CRC: F28A211F
CMT_SECURE_ROM_CRC: CEA7B19D
CMT Ready!
Searching for BootCode: DualLine 32Bit
RAP3Gv2_2nd.fg, Type: 2nd Boot Loader, Rev: 0.1.21.0, Algo: BB5
Flashbus Write baud set to 1.0Mbits
Flashbus Read baud set to 98Kbits
Using OLD BB5 FLASHING PROTOCOL
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.



With untick TX2


FlashChip[0,APE]: 0x0098003600A500C0, Toshiba, NAND
Requested Algorithm: OMAP1610 GBBM-1.8.1 ALG (APE)
FlashContent[0,APE]: 00020000000600000000000000000000, NAND
Searching for BootCode: Single Line 8Bit
FlashChip 0x00980036 (Toshiba), Size: 64MBytes, VPP: 21V
h3_sam_nand_gbbm.fg, Type: Algorithm, Rev: 0.1.33.0, Algo: OMAP1610 GBBM-1.8.1 ALG
Box VPP disabled
Internal APE Phone VPP Enabled
PAPUBKEYS Hash for APE: 0F72BF9DE5D6711B3B1133EBCAB5914FA419C78D
Flashbus Write baud set to 5.0Mbits
Storing NPC...
CMT CCC Not Found
CMT HWC Not Found
Storing VARIANT...
CMT PARTNERC Not Found
Processing APE Part...
Storing Product Code...
Storing PSN...
Storing HWID...
APE NPC Not Found
APE CCC Not Found
APE HWC Not Found
APE VARIANT Not Found
APE PARTNERC Not Found
Restarting MCU...
RPL Saved OK