nokia 1616 dead

[Karan_48]

nokia 1616 full flashed with some errors and can't power on.... here is log of flashing:-
CPU: XGOLD 110
Using embedded SBL from MCU.
Sending EBL Loader ...OK
Sending EBL ...OK
Getting EBL Version ...
Boot mode: 0xCC
EBL version major/minor: 10.19
EBL version: Default_RAM_Bootloader
Set baud rate to: 921.60 Kbit/s
Flash ID: 0020 88C0 - 23280003 [ST M58MWR064FU,64 Mbits]
CFI information:
Flash settings: 0/1, size: 0x00800000
2 Block regions:
127 x 0x00010000 = 0x007F0000
8 x 0x00002000 = 0x00010000
EBL ready !
Processing file: rh125_006.510
Downloading item CODE:hw_f11_rh125_r06.510.fls, num block: 3, size: 4.14 MB
Erasing area 0x00800000-0x00A0FFFE ...OK
Programming completed in 44.269 s
Erasing area 0x00C60000-0x00E72C7E ...OK
Programming completed in 44.637 s
Erasing area 0x00FFC000-0x00FFC03E ...OK
Programming completed in 0.181 s
Error reading checksum!
Processing file: rh125_006.51mg
Downloading item CUST:hw_f11_rh125_006.51mg.fls, num block: 1, size: 1.90 MB
Erasing area 0x00210000-0x003F6C3E ...OK
Programming completed in 36.506 s
Checksum mismatch: Phone calculated 0x0040, software calculated 0xC44A
Processing file: rh1250_nai06.51mg_nlt
Downloading item CUST:hw_f11_rh1250_nai06.51mg_nlt.fls , num block: 1, size: 772.64 KB
Erasing area 0x00EB0000-0x00F7057E ...OK
Programming completed in 14.578 s
Checksum mismatch: Phone calculated 0x00F8, software calculated 0x949E
Total time for flashing process(boot+erase+write) was 4 min 0.596 s


Phone type: RH-125
SW version: V 06.51 13-05-11 RH-125 (c) Nokia
Imei plain: 35154404383026-6
Product code: 0594703
Cellular system: GSM
ASIC ID: 0x2292, type: 11
Ppm Id: MG
Language Pack:
English,Hindi,Marathi

Imei net: 35154404383026
Provider: GSM Test Operator
Counter: 0/3, 0/10

CONFIG_DATA: 0010100000000000
PROFILE_BITS: 0000000000030002

BLOCK1: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK2: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK3: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK4: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK5: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK6: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK7: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
FULL FACTORY... OK
USER DATA... OK
LEAVE FACTORY... OK
SERVICE CENTER... OK
SOFTWARE UPGRADE... OK
PRODUCTION TUNING... OK
Reset User Code (to default:12345) ... OK
Completed in 2.263 s
how to solve this?????

[.::ZUBER::.]

Originally Posted by Karan_48

Phone type: RH-125
SW version: V 06.51 13-05-11 RH-125 (c) Nokia
Imei plain: 35154404383026-6
Product code: 0594703
Cellular system: GSM
ASIC ID: 0x2292, type: 11
Ppm Id: MG
Language Pack:
English,Hindi,Marathi

Bro. i didn't understand, please this from your logs:Product code: 0594703 , there is such product firmware available in Nokia Care Suite. Already your selected files not matching, so better select different firmware & Click Buscheck, if logs show certificates matching than flash it with that matching version.

BR,

[master2009]

check lcd ways in hardware

[kifayatjan]

bro check another versition file. ur broblem is file use full low ver or full haighi ver, this is tested by me.

[gbluez]

- make sure you are using latest mobileex version 3.5rev2.1
- try other firmware version.

if problem still remain, check phone hardware (bad flash chip)