I9100G resurrection problem - GSM-Forum

DrManila · 12-01-2011, 19:42

Hello. I have a problem with resurrection i9100G. My friend make him dead by flashing as i9100. When I connect it to USB I see OMAP4430 USB Device. Screen is blank, it is show nothing. When I try to resurrect it:

Code:

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.28, JTAG Manager Version: 1.37
Selected Resurrector: [Samsung i9100G XLoader+]

Connecting to the dead body...
ERROR: Set I/O Voltage to 2,60V failed. Real reading is 2,38V

Why I/O voltage is low? Withot phone connected it is ok. Wires are short and soldered right, I checked it two times. And also I want to ask what resurrector to use XLoader+ or XLoader- ?
p.s. Sorry for my bad English.

**legija** · 12-01-2011, 20:04

Hi,
In any case if phone is detected as blank OMAP4430, it wont work with neither of DLL-s, since now phone cpu is in sleep mode. Somewhar like it was with i9003.
For now there is no solution.

As for I/O voltage problem, this usually comes due to too long USB cables (both on box or phone) or bad power management on PC-s USB ports.

DrManila · 12-01-2011, 21:13

I/O voltage go down only when I connect my phone, when I press "Start probing" I/O Voltage is 2.65, but when I connect my I9100g I/O voltage is 2.38-2.50.
http://forum.gsmhosting.com/vbb/f634...3/#post7845624
Here RNC_EBM repaired this phone, is it possible?

BABAK NURI · 12-01-2011, 21:13

I Hope so release very soon....i have many pcs

12-01-2011, 19:42	#1 (permalink)
DrManila Freak Poster Join Date: May 2005 Age: 37 Posts: 177 Member: 148631 Status: Offline Thanks Meter: 9	I9100G resurrection problem Hello. I have a problem with resurrection i9100G. My friend make him dead by flashing as i9100. When I connect it to USB I see OMAP4430 USB Device. Screen is blank, it is show nothing. When I try to resurrect it: Code: Open serial port...OK Connecting to the RIFF Box...OK Firmware Version: 1.28, JTAG Manager Version: 1.37 Selected Resurrector: [Samsung i9100G XLoader+] Connecting to the dead body... ERROR: Set I/O Voltage to 2,60V failed. Real reading is 2,38V Why I/O voltage is low? Withot phone connected it is ok. Wires are short and soldered right, I checked it two times. And also I want to ask what resurrector to use XLoader+ or XLoader- ? p.s. Sorry for my bad English.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
6150 Lock Problem	Zeljko	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	2	10-16-2013 08:16
GId1 problem	old_man	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	1	10-18-2006 15:21
6110 5.47 sw unlock problem	gsms	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	3	11-21-1999 19:43
HELP: Problem with 5110	Xabi	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	1	07-16-1999 00:44

12-01-2011, 20:04	#2 (permalink)
legija Product Manager Join Date: Apr 2006 Age: 55 Posts: 5,746 Member: 256342 Status: Offline Sonork: None Thanks Meter: 28,276	Hi, In any case if phone is detected as blank OMAP4430, it wont work with neither of DLL-s, since now phone cpu is in sleep mode. Somewhar like it was with i9003. For now there is no solution. As for I/O voltage problem, this usually comes due to too long USB cables (both on box or phone) or bad power management on PC-s USB ports.

12-01-2011, 21:13	#3 (permalink)
DrManila Freak Poster Join Date: May 2005 Age: 37 Posts: 177 Member: 148631 Status: Offline Thanks Meter: 9	I/O voltage go down only when I connect my phone, when I press "Start probing" I/O Voltage is 2.65, but when I connect my I9100g I/O voltage is 2.38-2.50. http://forum.gsmhosting.com/vbb/f634...3/#post7845624 Here RNC_EBM repaired this phone, is it possible?

12-01-2011, 21:13	#4 (permalink)
BABAK NURI Product Supporter Join Date: Mar 2005 Location: Tehran.IR Age: 43 Posts: 7,259 Member: 131131 Status: Offline Sonork: 100.1606847 Thanks Meter: 4,475	I Hope so release very soon....i have many pcs