GSM-Forum

GSM-Forum (https://forum.gsmhosting.com/vbb/)
-   BB5 Easy Service Tool (BEST) Nokia Dongle (https://forum.gsmhosting.com/vbb/f641/)
-   -   Success Test Reports (https://forum.gsmhosting.com/vbb/f641/success-test-reports-2192308/)

YellowBoss 02-12-2017 11:08

Success Test Reports
 
Dear Sirs,

Here is one more thread for success test reports. I hope your opertaion logs and phone details may helps to users and developers in their work.
Thank you !

VIJAY2U2 02-12-2017 11:14

Nokia 206
 
Nokia 206 Flashing Done


Code:

Core : v2.25 , BB5XG FlashEngine : v10.3

Selected FlashSettings : Manual
Check FlashFiles, Please, wait...

Files Set for Flashing :
MCU : rm872__04.52.mcusw
PPM : rm872__04.52.ppm_mh2
CNT : rm872__04.52.image_mh2_059Q316_059R9M3_232_01
Flashing phone now...
[Gen] Rules accepted for : XGOLD Generation
Check files done...
-> SWversion check skipped : Dead mode selected
Dead Mode is Selected
Waiting for USB device...

-> If Windows say "Unrecognized device" / Operation not start
-> Or if Phone start charge - just reinsert battery
-> If flashing freeze - reinsert cable/battery and try again
--- Press phone's power button or insert usb cable! ---

Connection opened successfully

IF Boot Init : 0xF0
IF Resp Len  : 0x0A
IF xCPUID    : XGOLD 213 [XMM2130 QUANTUM]
IF Resp Data  :  1FB300020303010100FF

Sending EBL Loader ...
EBL Loader Ok, 01
EBL Loader ready, AA
Sending EBL ...
EBL sent Ok
EBL : Quantum_Bootloader_10.53_M1S1
Speed accepted, use 6.500.000
FLASHID : EC001230
FLIC conf set, RST set
Boot done!

Check keys...
Check done. Image can be flashed

Settings : EDM [0x8] , Block Mode , Fast CRC , Verify

  ===Flashing [MCU]===
File : rm872__04.52.mcusw
Image : rm872__04.52.mcusw_ebl_psi.fls
Sec-pack found, sending ...
Sec-pack sent
Found 5 region(s)
Processing Region 1/5
Erase , Start : 0x40000000 , Len : 0x00020000
Erasing, wait ...
Erase done, time : 00:00:00
Write , Start : 0x40000000 , Len : 0x00020000
Flashing , wait ...
Region flash done, time : 00:00:00
Processing Region 2/5
Erase , Start : 0x40040000 , Len : 0x00020000
Erasing, wait ...
Erase done, time : 00:00:00
Write , Start : 0x40040000 , Len : 0x00020000
Flashing , wait ...
Region flash done, time : 00:00:00
Processing Region 3/5
Erase , Start : 0x40060000 , Len : 0x00100000
Erasing, wait ...
Erase done, time : 00:00:02
Write , Start : 0x40060000 , Len : 0x00100000
Flashing , wait ...
Region flash done, time : 00:00:01
Processing Region 4/5
Erase , Start : 0x40280000 , Len : 0x01800000
Erasing, wait ...
Erase done, time : 00:00:48
Write , Start : 0x40280000 , Len : 0x01800000
Flashing , wait ...
Region flash done, time : 00:00:32
Processing Region 5/5
Erase , Start : 0x43E20000 , Len : 0x00040000
Erasing, wait ...
Erase done, time : 00:00:00
No write data, skip
CRC check passed , 0xFA4D

  ===Flashing [PPM]===
File : rm872__04.52.ppm_mh2
Image : package_mh2.ppm_ebl_psi.fls
Sec-pack found, sending ...
Sec-pack sent
Found 1 region(s)
Processing Region 1/1
Erase , Start : 0x41A80000 , Len : 0x00680000
Erasing, wait ...
Erase done, time : 00:00:10
Write , Start : 0x41A80000 , Len : 0x0051A538
Flashing , wait ...
Region flash done, time : 00:00:06
CRC check passed , 0x956B

  ===Flashing [CNT]===
File : rm872__04.52.image_mh2_059Q316_059R9M3_232_01
Image : rm872__04.52.image_mh2_059Q316_059R9M3_232_01.fls
Sec-pack found, sending ...
Sec-pack sent
Found 2 region(s)
Processing Region 1/2
Erase , Start : 0x42100000 , Len : 0x01D20000
Erasing, wait ...
Erase done, time : 00:01:06
Write , Start : 0x42100000 , Len : 0x01200000
Flashing , wait ...
Region flash done, time : 00:00:22
Processing Region 2/2
Erase , Start : 0x43E60000 , Len : 0x000E0000
Erasing, wait ...
Erase done, time : 00:00:02
No write data, skip
CRC check passed , 0x3F7E

Flashing done!
Total flash time : 00:03:14
Reboot phone now...

Reading Phone Info....
Connected phone -  206
Software Info:    V 04.52 30-06-13 RM-872 (c) Nokia           
IMEI:  355761062413925
PPM version :  V 04.52 30-06-13 RM-872 (c) Nokia            MH2
Product code:  059R9M3
Wait, when phone will be ready ...
Checking...
SimLock status : SimLock is Ok
Security status : Security is Ok
Read Info Done!
Processing After Flash Defaults...
FullFactorySet... Ok!
UserDataDefaultsSet...OK!
ServiceDefaultsSet... Ok!
LeaveDefaultsSet... Ok!
ProductTuneSet...OK!
SwUpgradeSet...OK!
Check and Upload User Certificates ...
Total - 58 certs
Certificates found, skip upload ...
Battery voltage is enough for start
AfterFlash operations done ;D
Done!
Connect phone on selected interface...


Elapsed: 00:04:03
Connect phone on selected interface...


ishant 02-12-2017 11:20

Code:

Intex Q7 Format Done with SVC Mode
Code:

Operation : Format File System / Reset Settings [ v1.24 ]
Settings : SmartFormat is On

1. Remove battery. Insert battery back
2. Insert cable
3. In case of SVC init problems - connect with hold "VolDown" button!

 ====  Wait for phone...

Phone found! [ 34 ]
Port Opened
Sync...
InitSvc Done
Wait for phone...
Sync...
Init Ok , reset settings ...
Format Ok!
Done


VIJAY2U2 02-12-2017 16:41

Nokia 2690
 
Nokia 2690 Blinking Done


Code:

Core : v2.25 , BB5XG FlashEngine : v10.3

Selected FlashSettings : Manual
Check FlashFiles, Please, wait...

Files Set for Flashing :
MCU : rm635__10.65.mcusw
PPM : rm635__10.65.ppm_mr
CNT : rm635__10.65.image_mr_black
Flashing phone now...
[Gen] Rules accepted for : RAP3x Generation
Check files done...
-> SWversion check skipped : Dead mode selected
Getting product info...
Dead Mode is Selected
Waiting for USB device...
--- Press phone's power button or insert cable & charger! ---
Connection opened successfully
Waiting for communication response.
ASIC ID:      000000010000022600010006030C192101033000
CPU ID :      RAP3Gv3 , Features : No any extended features
RAP_PUB:  16B001169BFC015614A00BADF999EF4E45858FDF
CMT_ROOT:  9DDBFCFE6E73CED7D8C6268C8EB85723
PatchRAWLoader: Patched OK
Processing RAWLOADER...
Processing UPDAPP...
Processing PASUBTOC...
TIME : Boot time : 00:00:01
Reopening the connection...
Waiting for response: 30
ADL -> [2nd] changing...
ADL Server confirm flashmode!
ADL : Check data
ADL : Data accepted
  ===Flashing [MCU]===
Erase : Processing rm635__10.65.mcusw
Found 6 areas to erase
Erasing area 0x00000000 - 0x000006BF, NOR, CMT
Result: 0000
Erasing area 0x000006C0 - 0x0001FFFF, NOR, CMT
Result: 0000
Erasing area 0x00040000 - 0x000BFFFF, NOR, CMT
Result: 0000
Erasing area 0x000C0000 - 0x0013FFFF, NOR, CMT
Result: 0000
Erasing area 0x00140000 - 0x0137FFFF, NOR, CMT
Result: 0000
Erasing area 0x01380000 - 0x0151FFFF, NOR, CMT
Result: 0000
TIME : Erase time : 00:02:33
Write : Processing rm635__10.65.mcusw
Total 1165 [1165/0/0] blocks to write, writing...
CMT : Writing Hash CERT [NOLO]
CMT : Writing Hash CERT [KEYS]
CMT : Writing Hash CERT [PRIMAPP]
CMT : Writing Hash CERT [PASUBTOC]
CMT : Writing Hash CERT [PAPUBKEYS]
CMT : Writing Hash CERT [UPDAPP]
CMT : Writing Hash CERT [DSP0]
CMT : Writing Hash CERT [MCUSW]
TIME : Write time : 00:00:54
MCU Write done
  ===Flashing [PPM]===
Erase : Processing rm635__10.65.ppm_mr
Found 1 areas to erase
Erasing area 0x01520000 - 0x01DBFFFF, NOR, CMT
Result: 0000
TIME : Erase time : 00:01:02
Write : Processing rm635__10.65.ppm_mr
Total 205 [205/0/0] blocks to write, writing...
TIME : Write time : 00:00:09
PPM Write done
  ===Flashing [CNT]===
Erase : Processing rm635__10.65.image_mr_black
Found 2 areas to erase
Erasing area 0x01DC0000 - 0x0215FFFF, NOR, CMT
Result: 0000
Erasing area 0x02160000 - 0x03FBFFFF, NOR, CMT
Result: 0000
TIME : Erase time : 00:06:43
Checking content info...
Check Image : Content size is 128k, use direct write mode
Write : Processing rm635__10.65.image_mr_black
Total 488 [488/0/0] blocks to write, writing...
TIME : Write time : 00:00:23
CNT Write done
ADL : End flashing

Flashing done!
Total flash time : 00:11:48
Reboot phone now...

Reading Phone Info....
Connected phone -  Nokia 2690
Software Info:    V 10.65 09-12-10 RM-635 (c) Nokia           
IMEI:  353795045073556
PPM version :  V 10.65 09-12-10 RM-635 (c) Nokia            MR
Product code:  0592107
Wait, when phone will be ready ...
Checking...
SimLock status : SimLock is Ok
Security status : Security is Ok
Read Info Done!
Processing After Flash Defaults...
FullFactorySet... Ok!
UserDataDefaultsSet...OK!
ServiceDefaultsSet... Ok!
LeaveDefaultsSet... Ok!
ProductTuneSet...OK!
SwUpgradeSet...OK!
Check and Upload User Certificates ...
Total - 0 certs
Uploading User Certificates...
Uploaded 26 certs!
Battery voltage is enough for start
AfterFlash operations done ;D
Done!

Elapsed: 00:12:47


iOS_Shakil 02-13-2017 07:34

Nokia Rm-921 Flash Done................

Code:

Connect phone on selected interface...

Core : v2.25 , BB5XG FlashEngine : v10.3

Selected FlashSettings : Manual
->  File : rm921_14.0.2_059S4B4_m1_2032_02_452463.rofs.fpsx not found! Check it!
File [Ok] : rm921_14.0.6.mcusw.fpsx
File [Ok] : rm921_14.0.2_059S4B4_m1_2032_02_452463.image.fpsx

Dead Mode is Selected
Waiting for USB device...
If PC not detect phone - Insert Cable first, then Insert battery
If stuck on boot  - remove MicroSD card from phone!
--- Press phone's power button or insert cable & charger! ---

1st Boot Done, processing booting now
ASIC ID_F    : 00000C2016100040498A2109861C603409A13428
ASIC ID_E    : 00000C2016100040
PUBLIC ID    : 50EEF98AAE3E17F4498A2109861C603409A13428
XGCHIP ID    : 50EEF98AAE3E17F4
ROOT KEY HASH : 125FC72605B5C4E48A9E0225084D2579
ROM ID        : 535882252F54C676

Prepare and send 2nd loader...
2nd boot Ok
Prepare and send Algo loader...
Algo boot Ok

IMEI [1] : 358149054250629
IMEI [2] : 358149054250637
NPC Certificate saved...
CCC Certificate saved...
HWC Certificate saved...

RPL saved : C:\InfinityBox\BEST\Backup\Cert\358149054250629_XG223_CRT.rpl

PAPUBkeys : 7EC22006F565793C24924878FBAB9CA6CBE42C35


 === SW Version Check ===
- > UPGRADE
 === SW Version Check ===

  === Flashing MCU ===
Processing file : rm921_14.0.6.mcusw.fpsx
Erasing...
Writing...
Total blocks : 82
Writing RKH CRT [ISSW]
Writing RKH CRT [MEMSET]
Writing RKH CRT [PRIMAPP]
Writing RKH CRT [LOADER]
Writing RKH CRT [PASUBTOC]
Writing RKH CRT [PAPUBKEYS] [PAKeys : 7EC22006F565793C24924878FBAB9CA6CBE42C35]
Writing RKH CRT [UPDAPP]
Writing RKH CRT [MCUSW]
File processed Ok, 81 blocks were writen

  === Flashing CNT ===
Processing file : rm921_14.0.2_059S4B4_m1_2032_02_452463.image.fpsx
Erasing...
Writing...
Total blocks : 51
File processed Ok, 51 blocks were writen

Flashing done , total time : 00:00:55
Reboot phone to service mode...

Processing After Flash Defaults...
FullFactorySet... Ok!
UserDataDefaultsSet...OK!
ServiceDefaultsSet... Ok!
LeaveDefaultsSet... Ok!
ProductTuneSet...OK!
SwUpgradeSet...OK!
Check and Upload User Certificates ...
Total - 59 certs
Certificates found, skip upload ...
Battery voltage is enough for start
AfterFlash operations done ;D

Connect phone on selected interface...

Phone found!
Series 40 Device detected!
read info...  - Ok

Phone disconected!

Connect phone on selected interface...


ishant 02-13-2017 11:14

Code:

Micromax Q346 Format Done by SVC Mode
Code:

Operation : Format File System / Reset Settings [ v1.24 ]
Settings : SmartFormat is On

1. Remove battery. Insert battery back
2. Insert cable
3. In case of SVC init problems - connect with hold "VolDown" button!

 ====  Wait for phone...

Phone found! [ 34 ]
Port Opened
Sync...
InitSvc Done
Wait for phone...
Sync...
Init Ok , reset settings ...
Format Ok!
Done


ishant 02-13-2017 11:16

Code:

LAVA Captain Reset User Lock Done
Code:

Operation : Reset UserCode [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey ( '*' )

Wait for phone...
Phone found! [ 43 ]
Sync...
Sync Ok, read regs...
Inital regs read done
Boot Info :
BB_CPU_ID : 6261
BB_CPU_HW : CB01
BB_CPU_SW : 0001
BB_CPU_SB : 8000
BB_CPU_NM : [MediaTek] MT6261_S0000
BB_CPU_SN : AE5391E2C890A45D359EB50084066276
BROM Protocol Version : 05
Setting...
Setting done , result code 0x000E
BROM stage done
Seek and prepare DownloadAgent
DownloadAgent matching HW Found!
DA verify and select done
Sending DA to target ...
DA_INFO  : 0xC0 , Ver : 3.2 , BBID : 0x8E
SOC_VERIFY : 0xC1
BOOT_STYLE : SF_FLASH_BOOT
NOR Flash IC initialized
[0] : FLASH_VEN : 0x0112 , [MXIC] MX25L3291FWJI_09
[0] : FLASH_DIE : 00C2 0020 0016 0000
[0] : FLASH_LEN : 0x00300000
SDS_INFO : 0x002FE000 , 0x00002000
INT_RAM : 0x0000D000
EXT_RAM : 0x00400000

Backup done
Read ExtData
Sorting ExtData
Sort Ok, Rebuild Ok
Restore ExtData
All done
UserCode request removed
UserCode set to default ( 0000 or 1122 )

Done!
Elapsed: 00:00:12
Reconnect Power/Cable!


ishant 02-18-2017 14:23

Code:

Micromax D320 Hang On Logo Done
Code:

======= Flash
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 118 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6572
BB_CPU_NME : [MediaTek] MT6572_S00
BB_CPU_EXT : 0xCA01 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer  : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x88
NAND Flash : NOT INSTALLED
eMMC Flash : 90014A4834473164040500A29F2612BB
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x90 , OEM : 014A
[eMMC] : FLASH_INF : [HYNIX] , d1G4
[eMMC] : FLASH_CID : 90014A4834473164040500A29F2612BB
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00400000
[eMMC] : FLASH_LEN : 0x00000000E9000000
[eMMC] : FLASH_UCP : 3728 MiB [eMMC 4 GiB]
DEV RID    : 0xE8130045E0B7C2A9936FD39093480545
INT RAM    : 0x00020000
EXT RAM    : 0x20000000 [512 MiB]
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

ScatCFG : BaseBand : MT6572 , Project : s857_72_kk , Storage : EMMC
Setting : Flash Pre-Erase (Safe) : Enabled
Setting : AFF verify :  Enabled
Setting : HW verify :  Enabled

Switching to HSUSB
HSUSB Init Ok
BL : Check HW compatibility
BL : BBID supported by BootLoader!
BL : Check eMMC compatibility
BL : eMMC supported by BootLoader!

BL : BatteryLevel : Unknown (not supported or without battery)

BL : Flash Pre-Erase
Total blocks to Erase : 2
Erase : 0x0000000000C00000-0x0000000000100000
Erase : 0x0000000002900000-0x00000000A16C0000
Flash Pre-Erase Done, time used : 00:00:05

SecCfg Passed , 1799
BMT remark not need. Will skip
Sending Preloader ...
Use : preloader_s857_72_kk.bin
Preloader Sent , Init passed
SecCfg Passed , 1799
PartCount : 0015
Update PMT by user request
Repartition Done!
Use FLN Mode

Processing : Flash Write
Flash now : MBR
Image Flash Ok
Flash now : EBR1
Image Flash Ok
Flash now : UBOOT
Image Flash Ok
Flash now : BOOTIMG
Image Flash Ok
Flash now : RECOVERY
Image Flash Ok
Flash now : SEC_RO
Image Flash Ok
Flash now : LOGO
Image Flash Ok
Flash now : EBR2
Image Flash Ok
Flash now : ANDROID
Image Flash Ok
Flash now : CACHE
Image Flash Ok
Flash now : USRDATA
Image Flash Ok
Flash Write Done, time used : 00:18:40

Processing : Verify
Verify Passed : MBR
Verify Passed : EBR1
Verify Passed : UBOOT
Verify Passed : BOOTIMG
Verify Passed : RECOVERY
Verify Passed : SEC_RO
Verify Passed : LOGO
Verify Passed : EBR2
Verify Passed : ANDROID
Verify Passed : CACHE
Verify Passed : USRDATA
Data Verify Done, time used : 00:00:05

Update Mirror PMT
Update Done!

Update RomInfo done

Done!
Elapsed: 00:19:19
Reconnect Power/Cable!


ishant 02-18-2017 14:26

Code:

Intex Privacy Lock Done
Code:

Operation : Reset Privacy Lock [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 3 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6580
BB_CPU_NME : [MediaTek] MT6580_S00
BB_CPU_EXT : 0xCA00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer  : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x94
NAND Flash : NOT INSTALLED
eMMC Flash : 45010044533130303801BCA94BA83327
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x45 , OEM : 0100
[eMMC] : FLASH_INF : [SANDISK] , 8001S
[eMMC] : FLASH_CID : 45010044533130303801BCA94BA83327
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00400000
[eMMC] : FLASH_LEN : 0x00000001D2000000
[eMMC] : FLASH_UCP : 7456 MiB [eMMC 8 GiB]
DEV RID    : 0xE8130045391EFBF901F5819B3C7DAB70
INT RAM    : 0x00020000
EXT RAM    : 0x40000000 [1 GiB]
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

Checking data ...

Process block #1
Process block #2

Privacy Lock reset Ok!

Done!
Elapsed: 00:00:20
Reconnect Power/Cable!


ishant 02-18-2017 14:28

Code:

Noki 108 Blinking Done
Code:

Core : v2.24 , MTKx FlashEngine : v10.2

Verify files ...
MAUI : RM-944_ROM_eMP_20.06.11
VIVA : RM-944_VIVA_eMP_20.06.11
LANG : RM-944_LANG_PACK_ROM_MH_eMP_20.06.11
CUST : RM-944_CUSTPACK_ROM_MH_INDIA_IN_eMP_20.06.11
JMPT : RM-944_JUMP_TABLE_MH_INDIA_IN_eMP_20.06.11
 - > MODE : FullFlash

Dead Mode is Selected
Waiting for USB device...
1. Phone should be Off!
2. Battery must be charged and inserted! ( if not used external power )
 - > If phone can't switch to BL - use battery or flash from Local mode!

--- Insert USB cable now! ---
Wait for phone...
Phone found! [ 29 ]
Sync...
Sync Ok, read regs...
Inital regs read done
Boot Info :
BB_CPU_ID : 625A
BB_CPU_HW : CA01
BB_CPU_SW : 0001
BB_CPU_SB : 8000
BB_CPU_NM : [MediaTek] MT6250_S0001
BB_CPU_SN : EA76CEB70C36011DE54CD467B30BFA13
BROM Protocol Version : 05
BROM Status : 1012
Comm Status : 0000
EXBL Status : Alive [ USB Load Active ]
Switch to BL done
BL Version : 01
Setting...
Setting done , result code 0x8000
Project ID : Bree.20.06.11.p4
BROM/BL stage done
Seek and prepare DownloadAgent
DownloadAgent matching HW Found!
DA verify and select done
Sending DA to target ...
DA_eMP_Bree.fg
DA_VERIFY : 00
DA_JUMP  : 00040000
DA_AUTH  : Passed!
DA_INFO  : 0xC0 , Ver : 3.2 , BBID : 0x88
DA_CSTAT  : 0x5A
SOC_VERIFY : 0xC1
BOOT_STYLE : SF_FLASH_BOOT
NOR Flash IC initialized
[0] : FLASH_VEN : 0x00E2 , [WINBOND] W25Q32BV
[0] : FLASH_DIE : 00EF 0040 0016 0000
[0] : FLASH_LEN : 0x00400000
FAT_RANGE : 0x003A6000-0x003F3FFF , LEN : 0x0004E000
SecureDecrypt : RM-944_ROM_eMP_20.06.11
SecureDecrypt : RM-944_VIVA_eMP_20.06.11
SecureDecrypt : RM-944_LANG_PACK_ROM_MH_eMP_20.06.11
SecureDecrypt : RM-944_CUSTPACK_ROM_MH_INDIA_IN_eMP_20.06.11
SecureDecrypt : RM-944_JUMP_TABLE_MH_INDIA_IN_eMP_20.06.11
OVRLP : 000069B900000001
PHPID : Bree.20.06.11.p4
OVRLP : 00004DF900000001
DA : FORMAT_BIN
Processing Flash Pre-format
FILES : 5
SAFE_BLOCK : 04
FORMAT_BIN : Ok
WRITE_STYLE : DEF : 0x01 (SEQ)
Write : RM-944_ROM_eMP_20.06.11
Write : RM-944_LANG_PACK_ROM_MH_eMP_20.06.11
Write : RM-944_CUSTPACK_ROM_MH_INDIA_IN_eMP_20.06.11
Write : RM-944_JUMP_TABLE_MH_INDIA_IN_eMP_20.06.11
Write : RM-944_VIVA_eMP_20.06.11
CODE_DNLOAD : Ok
[VERIFY] DONE : RM-944_ROM_eMP_20.06.11
[VERIFY] DONE : RM-944_LANG_PACK_ROM_MH_eMP_20.06.11
[VERIFY] DONE : RM-944_CUSTPACK_ROM_MH_INDIA_IN_eMP_20.06.11
[VERIFY] DONE : RM-944_JUMP_TABLE_MH_INDIA_IN_eMP_20.06.11
[VERIFY] DONE : RM-944_VIVA_eMP_20.06.11
CODE_VERIFY : Ok
Executing FFS FORMAT now...
FAT_RANGE : 0x003A6000-0x003F3FFF , LEN : 0x0004E000
DA_RET  : DA_IN_PROGRESS
DA_RET  : FORMAT_DONE
Rebooting phone now

Flashing done!
Total flash time : 00:01:09
Reboot phone Ok

 - > Hint : If phone shows Battery charge icon -  press and hold PowerOn button 10 seconds

Wait, when phone will be ready ...
Reading Phone Info....
Software Info:    20.06.11 00-00-00 RM-944
IMEI:  357786060580506
Ape Version: NEMO G 59cb152c/0 (59cb152c+0) T Mon Jul  1 02:50:44 2013 U 69b804d5
PPM version :  MH
Product code:  059S7M6
Wait, when phone will be ready ...
Checking...
SimLock status : SimLock is Ok
Security status : Security is Ok
Read Info Done!

Connect phone on selected interface...


Phone found!
MTKx Nokia Phone detected
Read info... Ok


Phone disconected!


bright hlatini 02-18-2017 16:58

Nokia 105 rm-1134 hang on log done with format

Card found: S/N : xxxxxxxx , v0122
Registered to: xxxxxxxx

Dead Mode is Selected
Waiting for USB device...
1. Phone should be Off!
2. Battery must be charged and inserted! ( if not used external power )
- > If phone can't switch to BL - use battery or flash from Local mode!

--- Insert USB cable now! ---
Wait for phone...
Phone found! [ 43 ]
Sync...
Sync Ok, read regs...
Inital regs read done
Boot Info :
BB_CPU_ID : 6261
BB_CPU_HW : CB01
BB_CPU_SW : 0001
BB_CPU_SB : 8000
BB_CPU_NM : [MediaTek] MT6261_S0001
BB_CPU_SN : 9EE2B50B30BCEEB5894789E3B39FDA8C
BROM Protocol Version : 05
BROM Status : 0000
Comm Status : 0000
EXBL Status : Alive [ USB Load Active ]
Switch to BL done
BL Version : 01
Setting...
Setting done , result code 0x8000
Project ID : LAGOS61D.10.01.11.p2
BROM/BL stage done
Seek and prepare DownloadAgent
DownloadAgent matching HW Found!
DA verify and select done
Sending DA to target ...
DA_eMP_Lagos.fg
DA_VERIFY : 00
DA_JUMP : 00100000
DA_AUTH : Passed!
DA_INFO : 0xC0 , Ver : 3.2 , BBID : 0x8E
DA_CSTAT : 0x5A
SOC_VERIFY : 0xC1
BOOT_STYLE : SF_FLASH_BOOT
NOR Flash IC initialized
[0] : FLASH_VEN : 0x00EC , [GigaDevice] GD25LQ32
[0] : FLASH_DIE : 00C8 0060 0016 0000
[0] : FLASH_LEN : 0x00400000
FAT_RANGE : 0x00368000-0x003F7FFF , LEN : 0x00090000

Executing FFS FORMAT now...
FAT_RANGE : 0x00368000-0x003F7FFF , LEN : 0x00090000
DA_RET : DA_IN_PROGRESS
DA_RET : FORMAT_DONE

Connect phone on selected interface...

dey mobiles 02-22-2017 11:28

Code:

Panasonic ELUGA_I2 Read Patternlock Done
Code:

Operation : Read Pattern/DP Lock [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 3 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6737
BB_CPU_NME : [MediaTek] MT6737M|MT6737_S00
BB_CPU_EXT : 0xCB00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer  : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x93
NAND Flash : NOT INSTALLED
eMMC Flash : 460001154D323237F7920042ED32CA90
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x15 , OEM : 0100
[eMMC] : FLASH_INF : [SAMSUNG] , BM227
[eMMC] : FLASH_CID : 150100463732324D420092F790CA83ED
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00080000
[eMMC] : FLASH_LEN : 0x00000001D2000000
[eMMC] : FLASH_UCP : 7456 MiB [eMMC 8 GiB]
DEV RID    : 0xE813004539A64785F3F6C11A64E0127B
INT RAM    : 0x00020000
EXT RAM    : 0x40000000 [1 GiB]
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

Reading data ...

Get Locks ...
PatternLock Sequnce : 145698

Done!
Elapsed: 00:00:15
Reconnect Power/Cable!


Yusuf Lawal 02-22-2017 21:22

NOKIA 305 RM766 REBOOT AFTER DISPLAY LOGO FLASH DONE BY INFINITY BEST
http://i65.tinypic.com/f06kad.jpg

MTK CHIP 02-25-2017 09:03

NOKIA 220 Hang on logo Easily solve by Just one click... (Format)
 
Hi,

Got 220 from another shop and he tried flash the phone but not succeed but with BEST in one click phone alive.

Quote:

Dead Mode is Selected
Waiting for USB device...
1. Phone should be Off!
2. Battery must be charged and inserted! ( if not used external power )
- > If phone can't switch to BL - use battery or flash from Local mode!

--- Insert USB cable now! ---
Wait for phone...
Phone found! [ 26 ]
Sync...
Sync Ok, read regs...
Inital regs read done
Boot Info :
BB_CPU_ID : 625A
BB_CPU_HW : CA01
BB_CPU_SW : 0001
BB_CPU_SB : 8000
BB_CPU_NM : [MediaTek] MT6250_S0001
BB_CPU_SN : 29C252CADBD114A2CF903083145129FF
BROM Protocol Version : 05
BROM Status : 1012
Comm Status : 0000
EXBL Status : Alive [ USB Load Active ]
Switch to BL done
BL Version : 01
Setting...
Setting done , result code 0x8000
Project ID : Rivendell.10.03.11.p1
BROM/BL stage done
Seek and prepare DownloadAgent
DownloadAgent matching HW Found!
DA verify and select done
Sending DA to target ...
DA_eMP_Rivendell.fg
DA_VERIFY : 00
DA_JUMP : 00040000
DA_AUTH : Passed!
DA_INFO : 0xC0 , Ver : 3.2 , BBID : 0x88
DA_CSTAT : 0x5A
SOC_VERIFY : 0xC1
BOOT_STYLE : SF_FLASH_BOOT
NOR Flash IC initialized
[0] : FLASH_VEN : 0x00F8 , [WINBOND] W25Q128FW
[0] : FLASH_DIE : 00EF 0060 0018 0000
[0] : FLASH_LEN : 0x01000000
FAT_RANGE : 0x00A60000-0x00FF3FFF , LEN : 0x00594000

Executing FFS FORMAT now...
FAT_RANGE : 0x00A60000-0x00FF3FFF , LEN : 0x00594000
DA_RET : DA_IN_PROGRESS
DA_RET : FORMAT_DONE

Connect phone on selected interface...

THANKX FOR THIS GR8 TOOL.

ishant 02-25-2017 09:21

Code:

Karboon Titanium K9 Smart Privacy Protection Remove Done

Code:


Operation : Reset Privacy Lock [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 3 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6572
BB_CPU_NME : [MediaTek] MT6572_S00
BB_CPU_EXT : 0xCA01 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer  : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x88
NAND Flash : NOT INSTALLED
eMMC Flash : 700100563130303038500CA8566FC253
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x70 , OEM : 0100
[eMMC] : FLASH_INF : [KINGSTON] , 80001
[eMMC] : FLASH_CID : 700100563130303038500CA8566FC253
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00400000
[eMMC] : FLASH_LEN : 0x00000001C3000000
[eMMC] : FLASH_UCP : 7216 MiB [eMMC 8 GiB]
DEV RID    : 0xE8130045AD7E7A24BA8D96AB09050757
INT RAM    : 0x00020000
EXT RAM    : 0x20000000 [512 MiB]
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

Checking data ...

Process block #1
Process block #2

Privacy Lock reset Ok!

Done!
Elapsed: 00:00:33
Reconnect Power/Cable!




Nasir Mobiles 02-28-2017 14:42

Nokia 225 (RM-1011) Flashing Done


Code:

Core : v2.24 , MTKx FlashEngine : v10.2

Verify files ...
MAUI : RM-1011_ROM_eMP_30.06.11
VIVA : RM-1011_VIVA_eMP_30.06.11
LANG : RM-1011_LANG_PACK_ROM_IJ_eMP_30.06.11_001
CUST : RM-1011_CUSTPACK_ROM_IJ_MEA_PK_eMP_30.06.11_001
JMPT : RM-1011_JUMP_TABLE_IJ_MEA_PK_eMP_30.06.11_001
 - > MODE : FullFlash

Dead Mode is Selected
Waiting for USB device...
1. Phone should be Off!
2. Battery must be charged and inserted! ( if not used external power )
 - > If phone can't switch to BL - use battery or flash from Local mode!

--- Insert USB cable now! ---
Wait for phone...
Phone found! [ 8 ]
Sync...
Sync Ok, read regs...
Inital regs read done
Boot Info :
BB_CPU_ID : 6260
BB_CPU_HW : CB00
BB_CPU_SW : 0000
BB_CPU_SB : 8000
BB_CPU_NM : [MediaTek] MT6260_S0001
BB_CPU_SN : 83ECA11C11FCACDD5124005E689F48AF
BROM Protocol Version : 05
BROM Status : 0000
Comm Status : 0000
EXBL Status : Alive [ USB Load Active ]
Switch to BL done
BL Version : 01
Setting...
Setting done , result code 0x8000
Project ID : PEARL.20.10.11.p1
BROM/BL stage done
Seek and prepare DownloadAgent
DownloadAgent matching HW Found!
DA verify and select done
Sending DA to target ...
DA_eMP_Pearl.fg
DA_VERIFY : 00
DA_JUMP  : 00040000
DA_AUTH  : Passed!
DA_INFO  : 0xC0 , Ver : 3.2 , BBID : 0x8B
DA_CSTAT  : 0x5A
SOC_VERIFY : 0xC1
BOOT_STYLE : SF_FLASH_BOOT
NOR Flash IC initialized
[0] : FLASH_VEN : 0x00F8 , [WINBOND] W25Q128FW
[0] : FLASH_DIE : 00EF 0060 0018 0000
[0] : FLASH_LEN : 0x01000000
FAT_RANGE : 0x00C80000-0x00FF3FFF , LEN : 0x00374000
SecureDecrypt : RM-1011_ROM_eMP_30.06.11
SecureDecrypt : RM-1011_VIVA_eMP_30.06.11
SecureDecrypt : RM-1011_LANG_PACK_ROM_IJ_eMP_30.06.11_001
SecureDecrypt : RM-1011_CUSTPACK_ROM_IJ_MEA_PK_eMP_30.06.11_001
SecureDecrypt : RM-1011_JUMP_TABLE_IJ_MEA_PK_eMP_30.06.11_001
OVRLP : 000069B900000001
PHPID : PEARL.20.10.11.p1
OVRLP : 00004DF900000001
DA : FORMAT_BIN
Processing Flash Pre-format
FILES : 5
SAFE_BLOCK : 04
FORMAT_BIN : Ok
WRITE_STYLE : DEF : 0x01 (SEQ)
Write : RM-1011_ROM_eMP_30.06.11
Write : RM-1011_LANG_PACK_ROM_IJ_eMP_30.06.11_001
Write : RM-1011_CUSTPACK_ROM_IJ_MEA_PK_eMP_30.06.11_001
Write : RM-1011_JUMP_TABLE_IJ_MEA_PK_eMP_30.06.11_001
Write : RM-1011_VIVA_eMP_30.06.11
CODE_DNLOAD : Ok
[VERIFY] DONE : RM-1011_ROM_eMP_30.06.11
[VERIFY] DONE : RM-1011_LANG_PACK_ROM_IJ_eMP_30.06.11_001
[VERIFY] DONE : RM-1011_CUSTPACK_ROM_IJ_MEA_PK_eMP_30.06.11_001
[VERIFY] DONE : RM-1011_JUMP_TABLE_IJ_MEA_PK_eMP_30.06.11_001
[VERIFY] DONE : RM-1011_VIVA_eMP_30.06.11
CODE_VERIFY : Ok
Executing FFS FORMAT now...
FAT_RANGE : 0x00C80000-0x00FF3FFF , LEN : 0x00374000
DA_RET  : DA_IN_PROGRESS
DA_RET  : FORMAT_DONE
Rebooting phone now

Flashing done!
Total flash time : 00:03:02
Reboot phone Ok

Connect phone on selected interface...


Nasir Mobiles 03-01-2017 11:24

Nokia 112 ( RM-837 ) Flash Succeed

Code:

Core : v2.24 , BB5XG FlashEngine : v10.3

Selected FlashSettings : Manual
Check FlashFiles, Please, wait...

Files Set for Flashing :
MCU : rm837__03.51.mcusw
PPM : rm837__03.51.ppm_m2
CNT : rm837__03.51.image_m2_059P7C1
Flashing phone now...
[Gen] Rules accepted for : XGOLD Generation
Check files done...
-> SWversion check skipped : Dead mode selected
Dead Mode is Selected
Waiting for USB device...

-> If Windows say "Unrecognized device" / Operation not start
-> Or if Phone start charge - just reinsert battery
-> If flashing freeze - reinsert cable/battery and try again
--- Press phone's power button or insert usb cable! ---

Connection opened successfully

IF Boot Init : 0xF0
IF Resp Len  : 0x0A
IF xCPUID    : XGOLD 213 [XMM2130 QUANTUM]
IF Resp Data  :  1FB300020303010100FF

Sending EBL Loader ...
EBL Loader Ok, 01
EBL Loader ready, AA
Sending EBL ...
EBL sent Ok
EBL : Quantum_Bootloader_10.50_M1S1
Speed accepted, use 6.500.000
FLASHID : 89008289
FLIC conf set, RST set
Boot done!

Check keys...
Check done. Image can be flashed

Backup enabled, will read all certificates

Reading CCC
Reading HWC
Reading NPC

IMEI 1 : 356331053660584
IMEI 2 : 356331053660592
PCcode : 059P7C1

NPC Certificate saved...
CCC Certificate saved...
HWC Certificate saved...

RPL saved : C:\InfinityBox\BEST\Backup\Cert\356331053660584_XG213_CRT.rpl

Settings : EDM [0x8] , Block Mode , Fast CRC , Verify

  ===Flashing [MCU]===
File : rm837__03.51.mcusw
Image : rm837__03.51.mcusw_ebl_psi.fls
Sec-pack found, sending ...
Sec-pack sent
Found 5 region(s)
Processing Region 1/5
Erase , Start : 0x40000000 , Len : 0x00020000
Erasing, wait ...
Erase done, time : 00:00:00
Write , Start : 0x40000000 , Len : 0x00020000
Flashing , wait ...
Region flash done, time : 00:00:00
Processing Region 2/5
Erase , Start : 0x40040000 , Len : 0x00020000
Erasing, wait ...
Erase done, time : 00:00:00
Write , Start : 0x40040000 , Len : 0x00020000
Flashing , wait ...
Region flash done, time : 00:00:00
Processing Region 3/5
Erase , Start : 0x40060000 , Len : 0x00100000
Erasing, wait ...
Erase done, time : 00:00:05
Write , Start : 0x40060000 , Len : 0x00100000
Flashing , wait ...
Region flash done, time : 00:00:01
Processing Region 4/5
Erase , Start : 0x40280000 , Len : 0x01940000
Erasing, wait ...
Erase done, time : 00:02:12
Write , Start : 0x40280000 , Len : 0x018C0000
Flashing , wait ...
Region flash done, time : 00:00:29
Processing Region 5/5
Erase , Start : 0x43E20000 , Len : 0x00040000
Erasing, wait ...
Erase done, time : 00:00:00
No write data, skip
CRC check passed , 0x87F4

  ===Flashing [PPM]===
File : rm837__03.51.ppm_m2
Image : package_m2.ppm_ebl_psi.fls
Sec-pack found, sending ...
Sec-pack sent
Found 1 region(s)
Processing Region 1/1
Erase , Start : 0x41BC0000 , Len : 0x00600000
Erasing, wait ...
Erase done, time : 00:00:17
Write , Start : 0x41BC0000 , Len : 0x0030F7C0
Flashing , wait ...
Region flash done, time : 00:00:03
CRC check passed , 0x46E6

  ===Flashing [CNT]===
File : rm837__03.51.image_m2_059P7C1
Image : package_m2_059P7C1.image.fls
Sec-pack found, sending ...
Sec-pack sent
Found 2 region(s)
Processing Region 1/2
Erase , Start : 0x421C0000 , Len : 0x01C60000
Erasing, wait ...
Erase done, time : 00:04:14
Write , Start : 0x421C0000 , Len : 0x00EE0000
Flashing , wait ...
Region flash done, time : 00:00:19
Processing Region 2/2
Erase , Start : 0x43E60000 , Len : 0x000E0000
Erasing, wait ...
Erase done, time : 00:00:08
No write data, skip
CRC check passed , 0x2559

Flashing done!
Total flash time : 00:07:53
Reboot phone now...


ishant 03-01-2017 13:28

Code:

Intex Cloud 4+ Usercode Remove Done

Code:


Operation : Format File System
Settings : SmartFormat is On

Waiting phone ...
Connect battery, press and hold 'VolUP' + 'PowerOn' buttons
Connect USB cable and keep hold buttons, until phone will be detected

Device found!
Handshake Ok!

Processing UBOT init ...
UBOOT FCS Init Ok!
Processing FL init ...
Handshake with FL Ok!

Factory Defaults : Will reset UserData and Settings!
Format USERDATA partition ...
Format USER Ok

Reboot Phone

Elapsed: 00:00:20
Reconnect Power/Cable!




Nasir Mobiles 03-01-2017 14:12

Nokia 108 (RM-944) MTK Flash succeed

Code:

Core : v2.24 , MTKx FlashEngine : v10.2

Verify files ...
MAUI : RM-944_ROM_eMP_20.06.11
VIVA : RM-944_VIVA_eMP_20.06.11
LANG : RM-944_LANG_PACK_ROM_IJ_eMP_20.06.11
CUST : RM-944_CUSTPACK_ROM_IJ_MEA_PK_eMP_20.06.11
JMPT : RM-944_JUMP_TABLE_IJ_MEA_PK_eMP_20.06.11
 - > MODE : FullFlash

Dead Mode is Selected
Waiting for USB device...
1. Phone should be Off!
2. Battery must be charged and inserted! ( if not used external power )
 - > If phone can't switch to BL - use battery or flash from Local mode!

--- Insert USB cable now! ---
Wait for phone...
Phone found! [ 7 ]
Sync...
Sync Ok, read regs...
Inital regs read done
Boot Info :
BB_CPU_ID : 625A
BB_CPU_HW : CA01
BB_CPU_SW : 0001
BB_CPU_SB : 8000
BB_CPU_NM : [MediaTek] MT6250_S0001
BB_CPU_SN : C3C7E3072475988385339ECAF21B7A18
BROM Protocol Version : 05
BROM Status : 1012
Comm Status : 0000
EXBL Status : Alive [ USB Load Active ]
Switch to BL done
BL Version : 01
Setting...
Setting done , result code 0x8000
Project ID : Bree.20.06.11.p4
BROM/BL stage done
Seek and prepare DownloadAgent
DownloadAgent matching HW Found!
DA verify and select done
Sending DA to target ...
DA_eMP_Bree.fg
DA_VERIFY : 00
DA_JUMP  : 00040000
DA_AUTH  : Passed!
DA_INFO  : 0xC0 , Ver : 3.2 , BBID : 0x88
DA_CSTAT  : 0x5A
SOC_VERIFY : 0xC1
BOOT_STYLE : SF_FLASH_BOOT
NOR Flash IC initialized
[0] : FLASH_VEN : 0x00DB , [MX] MX25U3235E
[0] : FLASH_DIE : 00C2 0025 0036 0000
[0] : FLASH_LEN : 0x00400000
FAT_RANGE : 0x003A6000-0x003F3FFF , LEN : 0x0004E000
SecureDecrypt : RM-944_ROM_eMP_20.06.11
SecureDecrypt : RM-944_VIVA_eMP_20.06.11
SecureDecrypt : RM-944_LANG_PACK_ROM_IJ_eMP_20.06.11
SecureDecrypt : RM-944_CUSTPACK_ROM_IJ_MEA_PK_eMP_20.06.11
SecureDecrypt : RM-944_JUMP_TABLE_IJ_MEA_PK_eMP_20.06.11
OVRLP : 000069B900000001
PHPID : Bree.20.06.11.p4
OVRLP : 00004DF900000001
DA : FORMAT_BIN
Processing Flash Pre-format
FILES : 5
SAFE_BLOCK : 04
FORMAT_BIN : Ok
WRITE_STYLE : DEF : 0x01 (SEQ)
Write : RM-944_ROM_eMP_20.06.11
Write : RM-944_LANG_PACK_ROM_IJ_eMP_20.06.11
Write : RM-944_CUSTPACK_ROM_IJ_MEA_PK_eMP_20.06.11
Write : RM-944_JUMP_TABLE_IJ_MEA_PK_eMP_20.06.11
Write : RM-944_VIVA_eMP_20.06.11
CODE_DNLOAD : Ok
[VERIFY] DONE : RM-944_ROM_eMP_20.06.11
[VERIFY] DONE : RM-944_LANG_PACK_ROM_IJ_eMP_20.06.11
[VERIFY] DONE : RM-944_CUSTPACK_ROM_IJ_MEA_PK_eMP_20.06.11
[VERIFY] DONE : RM-944_JUMP_TABLE_IJ_MEA_PK_eMP_20.06.11
[VERIFY] DONE : RM-944_VIVA_eMP_20.06.11
CODE_VERIFY : Ok
Executing FFS FORMAT now...
FAT_RANGE : 0x003A6000-0x003F3FFF , LEN : 0x0004E000
DA_RET  : DA_IN_PROGRESS
DA_RET  : FORMAT_DONE
Rebooting phone now

Flashing done!
Total flash time : 00:00:56
Reboot phone Ok


dey mobiles 03-02-2017 07:24

Code:

Micromax Q346 FRP Remove Done
Code:


Operation : Format File System / Reset Settings [ v1.24 ]
Settings : SmartFormat is On

1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
3. Insert cable

 ====  Wait for phone...

Phone found! [ 34 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SPRD 773x eMMC loader v3 Infinity
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

FlashMode Set : Ok!
Checking Structure ...
Detected eMMC Flash , Structure detect Ok!

eMMC phone detected! Will use 'Safe Format' mode!

Mount : /data
Size  : 0x00000001624F7000
State : 0x0001

Mount : /cache
Size  : 0x0000000009600000
State : 0x0001

Prepare Ok! Format Ok!
Don't touch phone, until it fully bootup to "Welcome Screen"!

Android 5.x : Reset FRP Lock
Reset Ok!


Done!

Elapsed: 00:00:36

Reconnect Power/Cable!




anjanbonik 03-03-2017 16:09

Nokia X2 Hung On Logo Done
 
Nokia X2 Hung On Logo Done


http://i.imgur.com/8fD2ftx.png


Code:

Connect phone on selected interface...

Core : v2.24 , NXP FlashEngine : v5.2

Flash Mode : Full Update (System, User, Boot)
Check and select files according selected FlashMode

Ok, Set : rm1013_2.1.0.11_059W0F3_001_rawprogram_unsparse_ui.xml
Ok, Set : rm1013_2.1.0.11_user_prog_emmc_firehose_8x10.mbn


Dead Mode is Selected
1. Phone should be Off!
2. Press and hold 'Volume Down' button
3. Insert USB cable and hold button, until phone will be detected


Get Phone Initial Info
Product : MSM8610
Version : 0.5
Serial  : 3A1CEC6

Handshake Ok
Init[0] : 0x01000000
Init[1] : 0x30000000
Sending Loader ...
Init Loader ...
FireHose Initialized
Device Init Ok
Target VER : 1
Target CPU : 8x10
Target FLN : eMMC
Target CNF : 1000/C000/1000
Target DBG : [email protected] [email protected]

Files in Chain : 67
Flashing now

Flashing : rm1013_2.1.0.11_user_NON-HLOS.bin
ProgInit : start 16384, num 75203
ProgDone : Finished sector address 91587
Flash Ok
Flashing : rm1013_2.1.0.11_user_sbl1.mbn
ProgInit : start 147456, num 492
ProgDone : Finished sector address 147948
Flash Ok
Flashing : rm1013_2.1.0.11_user_sbl1.mbn
ProgInit : start 148480, num 492
ProgDone : Finished sector address 148972
Flash Ok
Flashing : rm1013_2.1.0.11_user_sdi.mbn
ProgInit : start 149504, num 45
ProgDone : Finished sector address 149549
Flash Ok
Flashing : rm1013_2.1.0.11_user_emmc_appsboot.mbn
ProgInit : start 180224, num 938
ProgDone : Finished sector address 181162
Flash Ok
Flashing : rm1013_2.1.0.11_user_emmc_appsboot.mbn
ProgInit : start 181248, num 938
ProgDone : Finished sector address 182186
Flash Ok
Flashing : rm1013_2.1.0.11_user_rpm.mbn
ProgInit : start 182272, num 296
ProgDone : Finished sector address 182568
Flash Ok
Flashing : rm1013_2.1.0.11_user_rpm.mbn
ProgInit : start 183272, num 296
ProgDone : Finished sector address 183568
Flash Ok
Flashing : rm1013_2.1.0.11_user_boot.img
ProgInit : start 196608, num 14549
ProgDone : Finished sector address 211157
Flash Ok
Flashing : rm1013_2.1.0.11_user_tz.mbn
ProgInit : start 229376, num 663
ProgDone : Finished sector address 230039
Flash Ok
Flashing : rm1013_2.1.0.11_user_tz.mbn
ProgInit : start 230376, num 663
ProgDone : Finished sector address 231039
Flash Ok
Flashing : rm1013_2.1.0.11_user_system_1.img
ProgInit : start 344064, num 262160
ProgDone : Finished sector address 606224
Flash Ok
Flashing : rm1013_2.1.0.11_user_system_2.img
ProgInit : start 606600, num 16
ProgDone : Finished sector address 606616
Flash Ok
Flashing : rm1013_2.1.0.11_user_system_3.img
ProgInit : start 610352, num 257992
ProgDone : Finished sector address 868344
Flash Ok
Flashing : rm1013_2.1.0.11_user_system_4.img
ProgInit : start 868352, num 16
ProgDone : Finished sector address 868368
Flash Ok
Flashing : rm1013_2.1.0.11_user_system_5.img
ProgInit : start 872104, num 258384
ProgDone : Finished sector address 1130488
Flash Ok
Flashing : rm1013_2.1.0.11_user_system_6.img
ProgInit : start 1130496, num 16
ProgDone : Finished sector address 1130512
Flash Ok
Flashing : rm1013_2.1.0.11_user_system_7.img
ProgInit : start 1130888, num 16
ProgDone : Finished sector address 1130904
Flash Ok
Flashing : rm1013_2.1.0.11_user_system_8.img
ProgInit : start 1134640, num 95712
ProgDone : Finished sector address 1230352
Flash Ok
Flashing : rm1013_2.1.0.11_user_system_9.img
ProgInit : start 1392640, num 16
ProgDone : Finished sector address 1392656
Flash Ok
Flashing : rm1013_2.1.0.11_user_system_10.img
ProgInit : start 1654784, num 16
ProgDone : Finished sector address 1654800
Flash Ok
Flashing : rm1013_2.1.0.11_user_system_11.img
ProgInit : start 1655176, num 16
ProgDone : Finished sector address 1655192
Flash Ok
Flashing : rm1013_2.1.0.11_user_cache_1.img
ProgInit : start 1777664, num 11376
ProgDone : Finished sector address 1789040
Flash Ok
Flashing : rm1013_2.1.0.11_user_recovery.img
ProgInit : start 1974272, num 15529
ProgDone : Finished sector address 1989801
Flash Ok
Flashing : rm1013_2.1.0.11_user_misc_erase.img
ProgInit : start 1998848, num 1
ProgDone : Finished sector address 1998849
Flash Ok
Flashing : rm1013_2.1.0.11_059W0F3_001.custom_1.img
ProgInit : start 2015232, num 262136
ProgDone : Finished sector address 2277368
Flash Ok
Flashing : rm1013_2.1.0.11_059W0F3_001.custom_2.img
ProgInit : start 2277376, num 16
ProgDone : Finished sector address 2277392
Flash Ok
Flashing : rm1013_2.1.0.11_059W0F3_001.custom_3.img
ProgInit : start 2277640, num 16
ProgDone : Finished sector address 2277656
Flash Ok
Flashing : rm1013_2.1.0.11_059W0F3_001.custom_4.img
ProgInit : start 2280856, num 258656
ProgDone : Finished sector address 2539512
Flash Ok
Flashing : rm1013_2.1.0.11_059W0F3_001.custom_5.img
ProgInit : start 2539520, num 16
ProgDone : Finished sector address 2539536
Flash Ok
Flashing : rm1013_2.1.0.11_059W0F3_001.custom_6.img
ProgInit : start 2542736, num 227528
ProgDone : Finished sector address 2770264
Flash Ok
Flashing : rm1013_2.1.0.11_059W0F3_001.custom_7.img
ProgInit : start 2801664, num 16
ProgDone : Finished sector address 2801680
Flash Ok
Flashing : rm1013_2.1.0.11_059W0F3_001.custom_8.img
ProgInit : start 2801928, num 16
ProgDone : Finished sector address 2801944
Flash Ok
Flashing : rm1013_2.1.0.11_user_userdata_1.img
ProgInit : start 2834432, num 80272
ProgDone : Finished sector address 2914704
Flash Ok
Flashing : rm1013_2.1.0.11_user_userdata_2.img
ProgInit : start 3096576, num 16
ProgDone : Finished sector address 3096592
Flash Ok
Flashing : rm1013_2.1.0.11_user_userdata_3.img
ProgInit : start 3097800, num 16
ProgDone : Finished sector address 3097816
Flash Ok
Flashing : rm1013_2.1.0.11_user_userdata_4.img
ProgInit : start 3358720, num 16
ProgDone : Finished sector address 3358736
Flash Ok
Flashing : rm1013_2.1.0.11_user_userdata_5.img
ProgInit : start 3620864, num 16
ProgDone : Finished sector address 3620880
Flash Ok
Flashing : rm1013_2.1.0.11_user_userdata_6.img
ProgInit : start 3622088, num 16
ProgDone : Finished sector address 3622104
Flash Ok
Flashing : rm1013_2.1.0.11_user_userdata_7.img
ProgInit : start 3883008, num 16
ProgDone : Finished sector address 3883024
Flash Ok
Flashing : rm1013_2.1.0.11_user_userdata_8.img
ProgInit : start 4145152, num 16
ProgDone : Finished sector address 4145168
Flash Ok
Flashing : rm1013_2.1.0.11_user_userdata_9.img
ProgInit : start 4146376, num 16
ProgDone : Finished sector address 4146392
Flash Ok
Flashing : rm1013_2.1.0.11_user_userdata_10.img
ProgInit : start 4407296, num 16
ProgDone : Finished sector address 4407312
Flash Ok
Flashing : rm1013_2.1.0.11_user_userdata_11.img
ProgInit : start 4669440, num 16
ProgDone : Finished sector address 4669456
Flash Ok
Flashing : rm1013_2.1.0.11_user_userdata_12.img
ProgInit : start 4670664, num 16
ProgDone : Finished sector address 4670680
Flash Ok
Flashing : rm1013_2.1.0.11_user_userdata_13.img
ProgInit : start 4931584, num 16
ProgDone : Finished sector address 4931600
Flash Ok
Flashing : rm1013_2.1.0.11_user_userdata_14.img
ProgInit : start 5193728, num 16
ProgDone : Finished sector address 5193744
Flash Ok
Flashing : rm1013_2.1.0.11_user_userdata_15.img
ProgInit : start 5194952, num 16
ProgDone : Finished sector address 5194968
Flash Ok
Flashing : rm1013_2.1.0.11_user_userdata_16.img
ProgInit : start 5455872, num 16
ProgDone : Finished sector address 5455888
Flash Ok
Flashing : rm1013_2.1.0.11_user_userdata_17.img
ProgInit : start 5718016, num 16
ProgDone : Finished sector address 5718032
Flash Ok
Flashing : rm1013_2.1.0.11_user_userdata_18.img
ProgInit : start 5980160, num 16
ProgDone : Finished sector address 5980176
Flash Ok
Flashing : rm1013_2.1.0.11_user_userdata_19.img
ProgInit : start 6242304, num 16
ProgDone : Finished sector address 6242320
Flash Ok
Flashing : rm1013_2.1.0.11_user_userdata_20.img
ProgInit : start 6504448, num 16
ProgDone : Finished sector address 6504464
Flash Ok
Flashing : rm1013_2.1.0.11_user_userdata_21.img
ProgInit : start 6766592, num 16
ProgDone : Finished sector address 6766608
Flash Ok
Flashing : rm1013_2.1.0.11_user_userdata_22.img
ProgInit : start 7028736, num 16
ProgDone : Finished sector address 7028752
Flash Ok
Flashing : rm1013_2.1.0.11_user_userdata_23.img
ProgInit : start 7290880, num 16
ProgDone : Finished sector address 7290896
Flash Ok
Flashing : rm1013_2.1.0.11_user_userdata_24.img
ProgInit : start 7553024, num 16
ProgDone : Finished sector address 7553040
Flash Ok

Chain finished, All files flashed!

Rebooting phone now

Flashing done!
Total flash time : 00:01:44

Connect phone on selected interface...

Phone found!
Nokia X Platform Phone detected
Read info... Ok


Phone disconected!

Connect phone on selected interface...


Sonu 03-04-2017 06:42

nokia 301 dead recover done
 
flash
Code:

Core : v2.25 , BB5XG FlashEngine : v10.3

Selected FlashSettings : Manual
Check FlashFiles, Please, wait...

Files Set for Flashing :
MCU : rm839__09.04.mcusw
PPM : rm839__09.04.ppm_mh2
CNT : rm839__09.04.image_mh2_059R2H1_059T029_229_04
Flashing phone now...
[Gen] Rules accepted for : XGOLD Generation
Check files done...
-> SWversion check skipped : Dead mode selected
Dead Mode is Selected
Waiting for USB device...

-> If Windows say "Unrecognized device" / Operation not start
-> Or if Phone start charge - just reinsert battery
-> If flashing freeze - reinsert cable/battery and try again
--- Press phone's power button or insert usb cable! ---

Connection opened successfully
IF Boot Init : 0xF0
IF Resp Len  : 0x16
IF xCPUID    : XGOLD 618 [XMM6180 QUARK]
IF uCHIPID    :  50A9070100030101E0002409301C055149EC0935FFFF
IF Resp Data  :  50A9070100030101

Wait for user action : Insert battery

Sending EBL Loader ...
EBL Loader Ok
EBL Loader ready
Sending EBL ...
EBL sent Ok
EBL : QUARK_1337.500_M1S1
QUARK EEP config Ok
FLASHID : EC004000 , [ MuxOneNAND ]
Boot conf set, Target Ready
Boot done!
Backup enabled, will read all certificates

Reading CCC
Reading HWC
Reading NPC

IMEI 1 : 357885051711987
IMEI 2 : 357885051711995
Phone Product Code : 059T029

NPC Certificate saved...
CCC Certificate saved...
HWC Certificate saved...

RPL saved : C:\InfinityBox\BEST\Backup\Cert\357885051711987_XG618_CRT.rpl


  ===Flashing [MCU]===
Processing file : rm839__09.04.mcusw
Region count : 8
00 : [ PSI ]  : psi_flash_unsigned.fls
01 : [ BCore ] : slb_signed.fls
02 : [ Code ]  : main_toc_signed.fls
03 : [ Code ]  : rm839__09.04.mcusw_signed_mcusw.fls
04 : [ Code ]  : swap_signed.fls
05 : [ Cust ]  : dynsw.fls
06 : [ Code ]  : aeneas_signed.fls
07 : [ Code ]  : fota_signed.fls
Parse done , flashing now

Flash : 00 : psi_flash_unsigned.fls
Sending Sec-Pack
SecInfo Area : 0x0000 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x00090000 , Len : 0x00020000
Erase now...
Erase done
Region Start : 0x00090000 , Data Len : 0x00010FB0
Region Load done
Write done
psi_flash_unsigned.fls image flash done

Flash : 01 : slb_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0001 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x60000000 , Len : 0x00040000
Erase now...
Erase done
Region Start : 0x60000000 , Data Len : 0x00040000
Region Load done
Write done
slb_signed.fls image flash done

Flash : 02 : main_toc_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0002 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x60040000 , Len : 0x00000400
Erase now...
Erase done
Region Start : 0x60040000 , Data Len : 0x00000400
Region Load done
Write done
main_toc_signed.fls image flash done

Flash : 03 : rm839__09.04.mcusw_signed_mcusw.fls
Sending Sec-Pack
SecInfo Area : 0x0003 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x62E00000 , Len : 0x01100000
Erase now...
Erase done
Erase area 0x01 , Start 0xFFF00000 , Len : 0x00080000
Erase now...
Erase done
Region Start : 0x62E00000 , Data Len : 0x00F0D4CC
Region Load done
Write done
rm839__09.04.mcusw_signed_mcusw.fls image flash done

Flash : 04 : swap_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0004 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x80000000 , Len : 0x00F00000
Erase now...
Erase done
Region Start : 0x80000000 , Data Len : 0x00C2BCD0
Region Load done
Write done
swap_signed.fls image flash done

Flash : 05 : dynsw.fls
Sending Sec-Pack
SecInfo Area : 0x0005 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x62080000 , Len : 0x00100000
Erase now...
Erase done
Region Start : 0x62080000 , Data Len : 0x00044000
Region Load done
Write done
dynsw.fls image flash done

Flash : 06 : aeneas_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0006 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x63F79C00 , Len : 0x00080000
Erase now...
Erase done
Region Start : 0x63F79C00 , Data Len : 0x00046870
Region Load done
Write done
aeneas_signed.fls image flash done

Flash : 07 : fota_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0007 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x61F00004 , Len : 0x0017FFFC
Erase now...
Erase done
Region Start : 0x61F00004 , Data Len : 0x00149890
Region Load done
Write done
fota_signed.fls image flash done

  ===Flashing [PPM]===
Processing file : rm839__09.04.ppm_mh2
Region count : 1
00 : [ Cust ]  : package_mh2.ppm_ebl_psi.fls
Parse done , flashing now

Flash : 00 : package_mh2.ppm_ebl_psi.fls
Sending Sec-Pack
SecInfo Area : 0x0000 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x80F00000 , Len : 0x00B00000
Erase now...
Erase done
Region Start : 0x80F00000 , Data Len : 0x0068BEAC
Region Load done
Write done
package_mh2.ppm_ebl_psi.fls image flash done

  ===Flashing [CNT]===
Processing file : rm839__09.04.image_mh2_059R2H1_059T029_229_04
Region count : 1
00 : [ Cust ]  : rm839__09.04.image_mh2_059R2H1_059T029_229_04.fls
Parse done , flashing now

Flash : 00 : rm839__09.04.image_mh2_059R2H1_059T029_229_04.fls
Sending Sec-Pack
SecInfo Area : 0x0000 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0xA1000000 , Len : 0x0C580000
Erase now...
Erase done
Erase area 0x01 , Start 0xAE000000 , Len : 0x00300000
Erase now...
Erase done
Region Start : 0xA1000000 , Data Len : 0x01DB4000
Region Load done
Write done
rm839__09.04.image_mh2_059R2H1_059T029_229_04.fls image flash done

Flashing done!
Total flash time : 00:00:14
Reboot phone now...

Reading Phone Info....
Connected phone -  Nokia 301 Dual SIM
Software Info:    V 09.04 03-12-13 RM-839 (c) Nokia           
IMEI:  3578*********
PPM version :  V 09.04 03-12-13 RM-839 (c) Nokia            MH2
Product code:  059T029
Wait, when phone will be ready ...
Checking...
SimLock status : SimLock is Ok
Security status : Security is Ok
Read Info Done!
Processing After Flash Defaults...
FullFactorySet... Ok!
UserDataDefaultsSet...OK!
ServiceDefaultsSet... Ok!
LeaveDefaultsSet... Ok!
ProductTuneSet...OK!
SwUpgradeSet...OK!
Check and Upload User Certificates ...
Total - 58 certs
Certificates found, skip upload ...
Battery voltage is enough for start
AfterFlash operations done ;D
Done!
Connect phone on selected interface...


Elapsed: 00:01:08
Connect phone on selected interface...


Phone found!
Series 40 Device detected!
read info...  - Ok

Phone disconected!

Connect phone on selected interface...


>>Gsmmilon>> 03-04-2017 11:03

Nokia 105 Dual MT6261 Phone Lock Remove Done Without Flash
 
Nokia 105 Dual MT6261 Phone Lock Remove Done Without Flash

http://i.imgur.com/Fr8bU5A.gif

azhergoga007 03-06-2017 04:44

Qmobile X25 MT6572 Stuck Logo Revocer Done By Flashing With Infinity CM2
 











http://i.imgur.com/HPHJQRo.jpg


Flash Done...
http://i.imgur.com/zyuwjjo.gif





http://i67.tinypic.com/2urnyxf.gif

:: NO FAKE ADVERTISEMENT ::
:: NO FAKE UPDATES ::
:: NO FAKE WORLD'S FIRST ::
:: NO FAKE BLA BLA BLA ::


Stay Tune!
More Developing!!
More coming!!!



http://i.imgur.com/HAJVkUJ.jpg

azhergoga007 03-06-2017 04:45

Qmobile X800 MT6592 Pettran Lock Read Done Save All Data With Great Infinity CM2
 










http://i.imgur.com/HPHJQRo.jpg


Read Pettran Done...
http://i.imgur.com/dEdc4A2.gif




http://i67.tinypic.com/2urnyxf.gif

:: NO FAKE ADVERTISEMENT ::
:: NO FAKE UPDATES ::
:: NO FAKE WORLD'S FIRST ::
:: NO FAKE BLA BLA BLA ::


Stay Tune!
More Developing!!
More coming!!!



http://i.imgur.com/HAJVkUJ.jpg

bhanumobiles 03-08-2017 11:27

NOKIA X2.02 RM 694 FULL FLAS DONE in bast dongle
 
NOKIA X2.02 RM 694 FULL FLAS DONE in bast dongle

Selected FlashSettings : FullFlash
Check FlashFiles, Please, wait...

Files Set for Flashing :
MCU : CC2F4A5A_rm694__11.79.mcusw
PPM : CB29780C_rm694__11.79.ppm_bg
CNT : 53D201F3_rm694__11.79.image_bg_059H3C5
Flashing phone now...
Check files done...
-> SWversion check skipped : Dead mode selected
Dead Mode is Selected
Waiting for USB device...

-> If Windows say "Unrecognized device" - just reinsert battery
-> If flashing freeze - reinsert cable and try again
--- Press phone's power button or insert charger! ---

Connection opened successfully
DBG : F00A1FB300020303010100FF
CPUID : XGOLD 213
2nd boot Ok, 01
2nd ready, AA
Sending Algo
Algo sent Ok
BL : Quantum_Bootloader_10.46_M1S1
Speed accepted, use 6.500.000
FLASHID : EC001230
FLIC conf set, RST set
Boot done!
Backup enabled, will read all certificates

Reading CCC
Reading HWC
Reading NPC

IMEI 1 : 358103053859583
IMEI 2 : 358103053859591
PCcode :  њ

NPC Certificate saved...
CCC Certificate saved...
HWC Certificate saved...

RPL saved : C:\Program Files\Nokia_Best\Backup\Cert\358103053859583_35810 3053859591_XG213_CRT.rpl


===Flashing [MCU]===
File : CC2F4A5A_rm694__11.79.mcusw
Image : rm694__11.79.mcusw_ebl_psi.fls
Cert block found, sending....
Cert sent
Found 5 region(s)
Processing Region 1/5
Erase , Start : 0x40000000 , Len : 0x00020000
Erasing, wait ...
Erase done, time : 00:00:00
Write , Start : 0x40000000 , Len : 0x00020000
Flashing , wait ...
Region flash done, time : 00:00:00
Processing Region 2/5
Erase , Start : 0x40040000 , Len : 0x00020000
Erasing, wait ...
Erase done, time : 00:00:00
Write , Start : 0x40040000 , Len : 0x00020000
Flashing , wait ...
Region flash done, time : 00:00:00
Processing Region 3/5
Erase , Start : 0x40060000 , Len : 0x00100000
Erasing, wait ...
Erase done, time : 00:00:02
Write , Start : 0x40060000 , Len : 0x00100000
Flashing , wait ...
Region flash done, time : 00:00:01
Processing Region 4/5
Erase , Start : 0x40280000 , Len : 0x01980000
Erasing, wait ...
Erase done, time : 00:00:50
Write , Start : 0x40280000 , Len : 0x01900000
Flashing , wait ...
Region flash done, time : 00:00:32
Processing Region 5/5
Erase , Start : 0x43E20000 , Len : 0x00040000
Erasing, wait ...
Erase done, time : 00:00:00
No write data, skip

===Flashing [PPM]===
File : CB29780C_rm694__11.79.ppm_bg
Image : package_bg.ppm_ebl_psi.fls
Cert block found, sending....
Cert sent
Found 1 region(s)
Processing Region 1/1
Erase , Start : 0x41C00000 , Len : 0x00700000
Erasing, wait ...
Erase done, time : 00:00:10
Write , Start : 0x41C00000 , Len : 0x0051758C
Flashing , wait ...
Region flash done, time : 00:00:05

===Flashing [CNT]===
File : 53D201F3_rm694__11.79.image_bg_059H3C5
Image : package_bg_059H3C5.image.fls
Cert block found, sending....
Cert sent
Found 2 region(s)
Processing Region 1/2
Erase , Start : 0x42300000 , Len : 0x01B20000
Erasing, wait ...
Erase done, time : 00:00:58
Write , Start : 0x42300000 , Len : 0x00D60000
Flashing , wait ...
Region flash done, time : 00:00:16
Processing Region 2/2
Erase , Start : 0x43E60000 , Len : 0x000E0000
Erasing, wait ...
Erase done, time : 00:00:02
No write data, skip

Flashing done!
Total flash time : 00:03:01
Reboot phone now...

Reading Phone Info....
Connected phone - X2-02
Software Info: V 11.79 15-08-12 RM-694 (c) Nokia
IMEI: 358103053859583
PPM version : V 11.79 15-08-12 RM-694 (c) Nokia BG
Product code: 059N1T6
Checking...
SimLock status : SimLock is Ok
Security status : Security is Ok
Read Info Done!
Settings After Flash Defaults...
ProductTuneSet...OK!
SwUpgradeSet...OK!
Checking User Certificates...
Total - 43 certs
Data exist, skip certificate repair...
Battery voltage is enough for start
Set phone to Normal mode...

iOS_Shakil 03-08-2017 16:34

Nokia 130 / RM-1035 Hang On Logo Solve By Nokia BEST Dnngle


Code:

Registered to: iOS_Shakil

Connect phone on selected interface...

Core : v2.25 , MTKx FlashEngine : v10.5

Verify files ...
MAUI : RM-1035_ROM_eMP_10.01.11
VIVA : RM-1035_VIVA_eMP_10.01.11
LANG : RM-1035_LANG_PACK_ROM_MS_eMP_10.01.11_001
CUST : RM-1035_CUSTPACK_ROM_MS_MEA_BD_eMP_10.01.11_001
JMPT : RM-1035_JUMP_TABLE_MS_MEA_BD_eMP_10.01.11_001
 - > MODE : FullFlash

Dead Mode is Selected
Waiting for USB device...
1. Phone should be Off!
2. Battery must be charged and inserted! ( if not used external power )
 - > If phone can't switch to BL - use battery or flash from Local mode!

--- Insert USB cable now! ---
Wait for phone...
Phone found! [ 25 ]
Sync...
Sync Ok, read regs...
Inital regs read done
Boot Info :
BB_CPU_ID : 6260
BB_CPU_HW : CB00
BB_CPU_SW : 0000
BB_CPU_SB : 8000
BB_CPU_NM : [MediaTek] MT6260_S0001
BB_CPU_SN : 27DC4CE511E5FB3DF5E2AB373713973B
BROM Protocol Version : 05
BROM Status : 0000
Comm Status : 0000
EXBL Status : Alive [ USB Load Active ]
Switch to BL done
BL Version : 01
Setting...
Setting done , result code 0x8000
Project ID : CRYSTAL.10.01.11.p2
BROM/BL stage done
Seek and prepare DownloadAgent
DownloadAgent matching HW Found!
DA verify and select done
Sending DA to target ...
DA_eMP_Crystal.fg
DA_VERIFY : 00
DA_JUMP  : 00040000
DA_AUTH  : Passed!
DA_INFO  : 0xC0 , Ver : 3.2 , BBID : 0x8B
DA_CSTAT  : 0x5A
SOC_VERIFY : 0xC1
BOOT_STYLE : SF_FLASH_BOOT
NOR Flash IC initialized
[0] : FLASH_VEN : 0x00E2 , [WINBOND] W25Q32BV
[0] : FLASH_DIE : 00EF 0040 0016 0000
[0] : FLASH_LEN : 0x00400000
FAT_RANGE : 0x003A4000-0x003F3FFF , LEN : 0x00050000
SecureDecrypt : RM-1035_ROM_eMP_10.01.11
SecureDecrypt : RM-1035_VIVA_eMP_10.01.11
SecureDecrypt : RM-1035_LANG_PACK_ROM_MS_eMP_10.01.11_001
SecureDecrypt : RM-1035_CUSTPACK_ROM_MS_MEA_BD_eMP_10.01.11_001
SecureDecrypt : RM-1035_JUMP_TABLE_MS_MEA_BD_eMP_10.01.11_001
OVRLP : 000069B900000001
PHPID : CRYSTAL.10.01.11.p2
OVRLP : 00004DF900000001
DA : FORMAT_BIN
Processing Flash Pre-format
FILES : 5
SAFE_BLOCK : 04
FORMAT_BIN : Ok
WRITE_STYLE : DEF : 0x01 (SEQ)
Write : RM-1035_ROM_eMP_10.01.11
Write : RM-1035_LANG_PACK_ROM_MS_eMP_10.01.11_001
Write : RM-1035_CUSTPACK_ROM_MS_MEA_BD_eMP_10.01.11_001
Write : RM-1035_JUMP_TABLE_MS_MEA_BD_eMP_10.01.11_001
Write : RM-1035_VIVA_eMP_10.01.11
CODE_DNLOAD : Ok
[VERIFY] DONE : RM-1035_ROM_eMP_10.01.11
[VERIFY] DONE : RM-1035_LANG_PACK_ROM_MS_eMP_10.01.11_001
[VERIFY] DONE : RM-1035_CUSTPACK_ROM_MS_MEA_BD_eMP_10.01.11_001
[VERIFY] DONE : RM-1035_JUMP_TABLE_MS_MEA_BD_eMP_10.01.11_001
[VERIFY] DONE : RM-1035_VIVA_eMP_10.01.11
CODE_VERIFY : Ok
Executing FFS FORMAT now...
FAT_RANGE : 0x003A4000-0x003F3FFF , LEN : 0x00050000
DA_RET  : DA_IN_PROGRESS
DA_RET  : FORMAT_DONE
Rebooting phone now

Flashing done!
Total flash time : 00:01:04
Reboot phone Ok

Connect phone on selected interface...


malik_luv 03-10-2017 10:27

HISENSE U601s FRP LOCK DONE BY CM2 DONGLE
 
FRP LOCK HISENSE U601s DONE BY CM2 DONGLE

Operation : Format File System / Reset Settings [ v1.24 ]
Operation : Format File System / Reset Settings [ v1.24 ]
Operation : Format File System / Reset Settings [ v1.24 ]
Settings : SmartFormat is On

1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
3. Insert cable

==== Wait for phone...

Phone found! [ 446 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC7731 Crev eMMC Loader v2.0
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

FlashMode Set : Ok!
Checking Structure ...
Detected eMMC Flash , Structure detect Ok!

eMMC phone detected! Will use 'Safe Format' mode!

Mount : /data
Size : 0x0000000129EF7000
State : 0x0001

Mount : /cache
Size : 0x0000000009600000
State : 0x0001

Prepare Ok! Format Ok!
Don't touch phone, until it fully bootup to "Welcome Screen"!

Android 5.x : Reset FRP Lock
Reset Ok!


Done!
Report Post

den fatih 03-13-2017 11:39

Lumia rm-914 flight mode done
 
Core : v2.25 , WP10x FlashEngine : v2.5

FFU : RM914_3058.50000.1425.0004_RETAIL_apac_indonesia_4 92_04_448124_prd_signed.ffu
Checking FFU file, wait...
FFU Revision ID : 2.0
FFU Model ID : Nokia.MSM8227.P6036
FFU RootKeyHash : F771E62AF89994064F77CD3BC16829503BDF9A3D
FFU Languages : Albanian , Arabic , Azerbaijan(Latin) , Belorusian , Bulgarian , Catalan , Croatian , Czech , Danish (Denmark) , Dutch (Netherlands) , English (UK) , English , Estonian , Filipino (Philippines) , Finnish , French , German , Greek , Hwbre (Israel) , Hindi (India) , Hungarian , Indonesian , Italian , Japanese , Kazakh , Korean , Latvian , Lithuanian , Macedonian , Malay (Malaysia) , Norwegian (Bokmal , Norway) , Persian (Iran) , Polish , Portuguese(Brazil) , Portuguese(Portugal) , Romanian , Russian , sr-latn-rs , Chinese , Slovak , Slovenian , Spanish(Mexico) , Spanish , Swedish , Thai , Chinese(Taiwan) , Turkish , Ukrainian , Uzbekistan(Latin) , Vietnamese ,
FFU ChipSectors : 15155200
FFU Header : 0x000E0000
FFU Payload : 0x65660000
FFU FastVerify : Ok

Waiting for phone...
Dead mode is selected , no phone in normal mode found
1. Press and hold "Volume Down"
2. Insert USB cable
3. Hold button until phone will be detected

Device catched in BOOT mode!
Boot Mode confirmed!
Setting Preloder
Collect Info...
Setting Application
Setting Secure
Collect Info...
=== Nokia Flash App info :
Protocol Version : 1.15
Protocol Implementation : 1.28
=== Phone Initial info :
Phone RMxxx ID : RM-914
Phone Model ID : Nokia.MSM8227.P6036.1.2
Phone Model PC : 059S3Q0
Phone IMEI : 358106058406565
=== eMMC info :
eMMC Vendor : Samsung
eMMC CID : 0015
eMMC Size : 7456 MiB
=== Security Initial info :
Security Status : 010100000101
Secure Boot : Enabled
Secure eFUSE : Enabled
JTAG : Disabled
RDC Key : Not Present (Retail)
UEFI SBoot : Enabled
SecHW Key : Exists
Device RootKey : F771E62AF89994064F77CD3BC16829503BDF9A3D
=== Other info :
SD present : True , 00203B00

Full Check skipped , will be checked by ImageSignature


Battery Level : 48%
RPMB Provision Status Code : 0x0101
Device RAM size : 512 MiB
Device not have ATRP
Backup to RAM Ok!

FFU : RM914_3058.50000.1425.0004_RETAIL_apac_indonesia_4 92_04_448124_prd_signed.ffu
Flashing FFU
Sending FFU Header CertData
Header sent , accepted :)
Perform Data Partition Erase
Erase done
Sending FFU Payload Data...
Finishing flashing

Flashing done!
Green Light :)

Image Sent, processing PostFlash
FinalConfig : abnormal status, error code : 0xFFFF0000
Make Factory Set : Ok
Restore RAMBkp : Ok
Update NVI from Image
Ok , NVI will be updated on first boot!
PostFlash Finished

Total flash time : 00:02:36

Rebooting

Connect phone on selected interface...

Phone found!
WP10/WP8x Lumia Phone detected
Read info... Ok

Phone disconected!

Connect phone on selected interface...
:)

sachu2002 03-18-2017 13:12

Rm-1011 phone lock reset done
 
--- Insert USB cable now! ---
Wait for phone...
Phone found! [ 8 ]
Sync...
Sync Ok, read regs...
Inital regs read done
Boot Info :
BB_CPU_ID : 6260
BB_CPU_HW : CB00
BB_CPU_SW : 0000
BB_CPU_SB : 8000
BB_CPU_NM : [MediaTek] MT6260_S0001
BB_CPU_SN : 42ACB82E4B2DD0C96C7190E62A6B5288
BROM Protocol Version : 05
BROM Status : 0000
Comm Status : 0000
EXBL Status : Alive [ USB Load Active ]
Switch to BL done
BL Version : 01
Setting...
BROM/BL stage done
MT626x : Reset User Code
All done! Remove USB cable
All Security Settings deactivated!
Code set to default : 12345
Done!
Connect phone on selected interface...

TATAISONA 03-19-2017 17:05

Nokia 130 Hang On Logo Done
 

Nasir Mobiles 03-20-2017 13:07

Nokia 215 (RM-1110) Write Firmware.

Code:

Core : v2.24 , MTKx FlashEngine : v10.2

Verify files ...
MAUI : RM-1110_ROM_eMP_12.03.11
VIVA : RM-1110_VIVA_eMP_12.03.11
LANG : RM-1110_LANG_PACK_ROM_IJ_eMP_12.03.11_001
CUST : RM-1110_CUSTPACK_ROM_IJ_MEA_PK_eMP_12.03.11_001
JMPT : RM-1110_JUMP_TABLE_IJ_MEA_PK_eMP_12.03.11_001
 - > MODE : FullFlash

Dead Mode is Selected
Waiting for USB device...
1. Phone should be Off!
2. Battery must be charged and inserted! ( if not used external power )
 - > If phone can't switch to BL - use battery or flash from Local mode!

--- Insert USB cable now! ---
Wait for phone...
Phone found! [ 256 ]
Sync...
Sync Ok, read regs...
Inital regs read done
Boot Info :
BB_CPU_ID : 6260
BB_CPU_HW : CB00
BB_CPU_SW : 0000
BB_CPU_SB : 8000
BB_CPU_NM : [MediaTek] MT6260_S0001
BB_CPU_SN : 831C611D521A43A07132AF1717EB0DE9
BROM Protocol Version : 05
BROM Status : 0000
Comm Status : 0000
EXBL Status : Alive [ USB Load Active ]
Switch to BL done
BL Version : 01
Setting...
Setting done , result code 0x8000
Project ID : JET.10.01.11.p1
BROM/BL stage done
Seek and prepare DownloadAgent
DownloadAgent matching HW Found!
DA verify and select done
Sending DA to target ...
DA_eMP_Jet.fg
DA_VERIFY : 00
DA_JUMP  : 00040000
DA_AUTH  : Passed!
DA_INFO  : 0xC0 , Ver : 3.2 , BBID : 0x8B
DA_CSTAT  : 0x5A
SOC_VERIFY : 0xC1
BOOT_STYLE : SF_FLASH_BOOT
NOR Flash IC initialized
[0] : FLASH_VEN : 0x00EF , [MXIC] MX25U12835FZNI_10G
[0] : FLASH_DIE : 00C2 0025 0038 0000
[0] : FLASH_LEN : 0x01000000
FAT_RANGE : 0x00E80000-0x00FF3FFF , LEN : 0x00174000
SecureDecrypt : RM-1110_ROM_eMP_12.03.11
SecureDecrypt : RM-1110_VIVA_eMP_12.03.11
SecureDecrypt : RM-1110_LANG_PACK_ROM_IJ_eMP_12.03.11_001
SecureDecrypt : RM-1110_CUSTPACK_ROM_IJ_MEA_PK_eMP_12.03.11_001
SecureDecrypt : RM-1110_JUMP_TABLE_IJ_MEA_PK_eMP_12.03.11_001
OVRLP : 000069B900000001
PHPID : JET.10.01.11.p1
OVRLP : 00004DF900000001
DA : FORMAT_BIN
Processing Flash Pre-format
FILES : 5
SAFE_BLOCK : 04
FORMAT_BIN : Ok
WRITE_STYLE : DEF : 0x01 (SEQ)
Write : RM-1110_ROM_eMP_12.03.11
Write : RM-1110_LANG_PACK_ROM_IJ_eMP_12.03.11_001
Write : RM-1110_CUSTPACK_ROM_IJ_MEA_PK_eMP_12.03.11_001
Write : RM-1110_JUMP_TABLE_IJ_MEA_PK_eMP_12.03.11_001
Write : RM-1110_VIVA_eMP_12.03.11
CODE_DNLOAD : Ok
[VERIFY] DONE : RM-1110_ROM_eMP_12.03.11
[VERIFY] DONE : RM-1110_LANG_PACK_ROM_IJ_eMP_12.03.11_001
[VERIFY] DONE : RM-1110_CUSTPACK_ROM_IJ_MEA_PK_eMP_12.03.11_001
[VERIFY] DONE : RM-1110_JUMP_TABLE_IJ_MEA_PK_eMP_12.03.11_001
[VERIFY] DONE : RM-1110_VIVA_eMP_12.03.11
CODE_VERIFY : Ok
Executing FFS FORMAT now...
FAT_RANGE : 0x00E80000-0x00FF3FFF , LEN : 0x00174000
DA_RET  : DA_IN_PROGRESS
DA_RET  : FORMAT_DONE
Rebooting phone now

Flashing done!
Total flash time : 00:02:50
Reboot phone Ok


UzUnlocker 03-22-2017 17:46

Lumia 640 DS RM-1077 Boot repair done via Infinity BEST Tool - World 1ST Tool
 
Repair boot via USB
Code:

Core : v2.26 , WP10x FlashEngine : v3.0

FFU : RM1077_02177.00000.15184.36002_RETAIL_prod_signed_1017_025FF3_000-RU_MV.ffu
Checking FFU file, wait...
FFU Revision ID  : 2.0
FFU Model ID      : Nokia.MSM8226.P6204
FFU RootKeyHash  : 0000000000000000000000000000000000000000
FFU Languages    : Portuguese(Brazil) , Russian , Greek , fr-ca , Indonesian , Korean , Polish , bn-bd , Uzbekistan(Latin) , Catalan , Swedish , Bulgarian , Japanese , Spanish , English (UK) , Czech , Latvian , Slovak , Chinese , sr-latn-rs , Vietnamese , af-za , Hindi (India) , gl-es , Turkish , Thai , Italian , Danish (Denmark) , ha-latn-ng , Slovenian , Malay (Malaysia) , Lithuanian , Persian (Iran) , Kazakh , Romanian , English , eu-es , Estonian , Filipino (Philippines) , Belorusian , Norwegian (Bokmal , Norway) , Finnish , lo-la , km-kh , Arabic , Ukrainian , Croatian , Portuguese(Portugal) , Chinese(Taiwan) , Macedonian , Hungarian , Spanish(Mexico) , Azerbaijan(Latin) , German , Albanian , Dutch (Netherlands) , French , sw-ke , Hwbre (Israel) ,
FFU ChipSectors  : 15155200
FFU Header        : 0x000E0000
FFU Payload      : 0x70060000
FFU FastVerify    : Ok

Waiting for phone...
Boot Repair mode is selected
1. Charge battery fully , insert in phone
2. Insert USB cable
3. If phone stuck in boot mode or shows Blue Screen - follow repair manual

Handshake Ok
Init[0] : 0x01000000
Init[1] : 0x30000000
Sending Loader ...
Init Loader ...
FW_REV : 000.001.000
MSM_ID : 008000E100000000
MSM_RK : 831BE6B18E7006372069545885A80F786C33D064
Sending and verify Signature
eMMC init Ok
[eMMC_VEN] : 0x0011
[eMMC_OEM] : 0x0000
[eMMC_REV] : 0x0000
[eMMC_CAP] : 0x00000001D2000000
Sending HashTable
Sending configuration data
Program [SBL1]
Program [RPM]
Program [TZ]
Program [UEFI]
Program [WINSECAPP]
Program [TZAPPS]
Program [DBI]
Clear [DDR]
Clear [PLAT]
Clear [EFIESP]
Program [8626_GPT_V1_0.BIN]
Rebooting ...
Reboot to UEFI now...
Repair done, verify now ...
Wait for device in UEFI ...
Device boot not done
Check Drivers, battery charge
Try again in Dead mode

Phone disconected!


After i just charge battery & flash FFU file ))
Code:

Core : v2.26 , WP10x FlashEngine : v3.0

FFU : RM1077_02177.00000.15184.36002_RETAIL_prod_signed_1017_025FF3_000-RU_MV.ffu
Checking FFU file, wait...
FFU Revision ID  : 2.0
FFU Model ID      : Nokia.MSM8226.P6204
FFU RootKeyHash  : 0000000000000000000000000000000000000000
FFU Languages    : Portuguese(Brazil) , Russian , Greek , fr-ca , Indonesian , Korean , Polish , bn-bd , Uzbekistan(Latin) , Catalan , Swedish , Bulgarian , Japanese , Spanish , English (UK) , Czech , Latvian , Slovak , Chinese , sr-latn-rs , Vietnamese , af-za , Hindi (India) , gl-es , Turkish , Thai , Italian , Danish (Denmark) , ha-latn-ng , Slovenian , Malay (Malaysia) , Lithuanian , Persian (Iran) , Kazakh , Romanian , English , eu-es , Estonian , Filipino (Philippines) , Belorusian , Norwegian (Bokmal , Norway) , Finnish , lo-la , km-kh , Arabic , Ukrainian , Croatian , Portuguese(Portugal) , Chinese(Taiwan) , Macedonian , Hungarian , Spanish(Mexico) , Azerbaijan(Latin) , German , Albanian , Dutch (Netherlands) , French , sw-ke , Hwbre (Israel) ,
FFU ChipSectors  : 15155200
FFU Header        : 0x000E0000
FFU Payload      : 0x70060000
FFU FastVerify    : Ok

Waiting for phone...
Dead mode is selected , no phone in normal mode found
1. Press and hold "Volume Down"
2. Insert USB cable
3. Hold button until phone will be detected

Device catched in BOOT mode!
Collect Info...
=== Nokia Flash App info :
Protocol Version        : 2.37
Protocol Implementation : 2.60
=== Phone Initial info :
Phone Model ID : Nokia.MSM8226.P6204.2.0
=== eMMC info :
eMMC Vendor : Toshiba
eMMC CID : 0011
eMMC Size : 7456 MiB
=== Security Initial info :
Security Status  : 010100000101
Secure Boot : Enabled
Secure eFUSE : Enabled
JTAG : Disabled
RDC Key : Not Present (Retail)
UEFI SBoot : Enabled
SecHW Key : Exists
Device RootKey    : 831BE6B18E7006372069545885A80F786C33D064
=== Other info :
SD present        : False

Full Check skipped , will be checked by ImageSignature


Battery Level : 1%
[Info] : Battery level is low, but ignored in settings. Continue at user risk.
RPMB Provision Status Code : 0x0101
Device RAM size : 1024 MiB
Device have ATRP (AntiTheft) system!
Backup to RAM Ok!

FFU : RM1077_02177.00000.15184.36002_RETAIL_prod_signed_1017_025FF3_000-RU_MV.ffu
Flashing FFU
Sending FFU Header CertData
Header sent , accepted :)
Perform Data Partition Erase
Error : 06 : Data Partition Not Found! Seems as damaged
Will Fix partitions by flash whole image
Sending FFU Header CertData
Header sent , accepted :)
Skip Data Partition Erase
Sending FFU Payload Data...
Finishing flashing

Flashing done!
Green Light :)

Image Sent, processing PostFlash
FinalConfig : abnormal status, error code : 0xFF7B0000
Make Factory Set : Ok
Restore RAMBkp : Ok
Update NVI from Image
Ok , NVI will be updated on first boot!
PostFlash Finished

Total flash time : 00:05:24

Rebooting

Connect phone on selected interface...

Phone found!
WP10/WP8x Lumia Phone detected




See Result :)

https://s8.postimg.org/50lseza7p/pho...2_21_45_03.jpg

Shensohau 03-23-2017 01:25

Nokia Lumia 640 DS AT&T Full Flash Done W1st
 
http://i67.tinypic.com/30dbgn4.jpg



Code:

Card found: S/N : XXXXXXX , v0135
Registered to: Shensohau

Connect phone on selected interface...

Core : v2.26 , WP10x FlashEngine : v3.0

FFU : RM1073_02177.00000.15184.36016_RETAIL_prod_signed_1004_022B79_ATT-US.ffu
Checking FFU file, wait...
FFU Revision ID  : 2.0
FFU Model ID      : Nokia.MSM8926.P6204_ATT
FFU RootKeyHash  : 0000000000000000000000000000000000000000
FFU Languages    : Portuguese(Brazil) , Russian , Greek , fr-ca , Indonesian , Korean , Polish , bn-bd , Uzbekistan(Latin) , Catalan , Swedish , Bulgarian , Japanese , Spanish , English (UK) , Czech , Latvian , Slovak , Chinese , sr-latn-rs , Vietnamese , af-za , Hindi (India) , gl-es , Turkish , Thai , Italian , Danish (Denmark) , ha-latn-ng , Slovenian , Malay (Malaysia) , Lithuanian , Persian (Iran) , Kazakh , Romanian , English , eu-es , Estonian , Filipino (Philippines) , Belorusian , Norwegian (Bokmal , Norway) , Finnish , lo-la , km-kh , Arabic , Ukrainian , Croatian , Portuguese(Portugal) , Chinese(Taiwan) , Macedonian , Hungarian , Spanish(Mexico) , Azerbaijan(Latin) , German , Albanian , Dutch (Netherlands) , French , sw-ke , Hwbre (Israel) ,
FFU ChipSectors  : 15155200
FFU Header        : 0x000E0000
FFU Payload      : 0x6F680000
FFU FastVerify    : Ok

Waiting for phone...
Dead mode is selected , no phone in normal mode found
1. Press and hold "Volume Down"
2. Insert USB cable
3. Hold button until phone will be detected

Device catched in BOOT mode!
Boot Mode confirmed!
Setting Preloder
Collect Info...
Setting Application
Setting Secure
Collect Info...
=== Nokia Flash App info :
Protocol Version        : 2.37
Protocol Implementation : 2.60
=== Phone Initial info :
Phone RMxxx ID : RM-1073
Phone Model ID : Nokia.MSM8926.P6204_ATT.1.1
Phone Model PC : 059X0B8
Phone IMEI    : 35781606XXXXXXX
=== eMMC info :
eMMC Vendor : Hynix
eMMC CID : 0090
eMMC Size : 7456 MiB
=== Security Initial info :
Security Status  : 010100000101
Secure Boot : Enabled
Secure eFUSE : Enabled
JTAG : Disabled
RDC Key : Not Present (Retail)
UEFI SBoot : Enabled
SecHW Key : Exists
Device RootKey    : 831BE6B18E7006372069545885A80F786C33D064
=== Other info :
SD present        : False

Full Check skipped , will be checked by ImageSignature


Battery Level : 31%
RPMB Provision Status Code : 0x0101
Device RAM size : 1024 MiB
Device have ATRP (AntiTheft) system!
Backup to RAM Ok!

FFU : RM1073_02177.00000.15184.36016_RETAIL_prod_signed_1004_022B79_ATT-US.ffu
Flashing FFU
Sending FFU Header CertData
Header sent , accepted :)
Perform Data Partition Erase
Erase done
Sending FFU Payload Data...
Finishing flashing

Flashing done!
Green Light :)

Image Sent, processing PostFlash
FinalConfig : abnormal status, error code : 0xFF7B0000
Make Factory Set : Ok
Restore RAMBkp : Ok
PostFlash Finished

Total flash time : 00:05:52

Thanks Infinity-Team
Thanks YellowBoss

Luckey1 03-27-2017 10:17

Nokia 216 RM-1187 User code reset done no data loss
 
Nokia 216 RM-1187 User code reset done no data loss

Quote:

Reading Phone Info....
Software ver : 11.00.11 00-00-00 RM-1187
IMEI 1 : 354884089433865
IMEI 2 : 354884089433873
XappVer : 000008D4
Ape Ver : NEMO G 59cb152c/0 (59cb152c+0) T Mon Jul 1 02:50:44 2013 U 69b804d5
PPM : IJ
CNT : SUEZ.11.00.11.p1
Product SN : FBD4CB2AU
Product code : 059X807
Base Prd.code: 059X9H2
Module code : 0207175
Hardware info=======
HWID : 1101
LCDVer: TPO
Lock info ===========
IMEI : 354884089433865
IMEI spNet : 3A 45 88 04 98 34 83 56

Conf key : 800000000004000B
Provider key : 2440700000000000
Country : Finland
Operator : NOKIA (Open)

Lock info:
Block 1
L1:Open; L2:Open; L3:Open; L4:Open; L5:Open;
Block 2
L1:Open; L2:Open; L3:Open; L4:Open; L5:Open;
Block 3
L1:Open; L2:Open; L3:Open; L4:Open; L5:Open;
Block 4
L1:Open; L2:Open; L3:Open; L4:Open; L5:Open;
Block 5
L1:Open; L2:Open; L3:Open; L4:Open; L5:Open;
Block 6
L1:Open; L2:Open; L3:Open; L4:Open; L5:Open;
Block 7
L1:Open; L2:Open; L3:Open; L4:Open; L5:Open;

SimLock status : Ok
Security status : Ok

Done!
Quote:

Dead Mode is Selected
Waiting for USB device...
1. Phone should be Off!
2. Battery must be charged and inserted! ( if not used external power )
- > If phone can't switch to BL - use battery or flash from Local mode!

--- Insert USB cable now! ---
Wait for phone...
Phone found! [ 220 ]
Sync...
Sync Ok, read regs...
Inital regs read done
Boot Info :
BB_CPU_ID : 6260
BB_CPU_HW : CB00
BB_CPU_SW : 0000
BB_CPU_SB : 8000
BB_CPU_NM : [MediaTek] MT6260_S0001
BB_CPU_SN : C9E9961D1EDB0300937E3BD9552C2390
BROM Protocol Version : 05
BROM Status : 0000
Comm Status : 0000
EXBL Status : Alive [ USB Load Active ]
Switch to BL done
BL Version : 01
Setting...
BROM/BL stage done
MT626x : Reset User Code
All done! Remove USB cable
All Security Settings deactivated!
Code set to default : 12345
Done!

amurale72 03-27-2017 13:45

Nokia x rm-980 flash suceessfully
 
Card found: S/N : 90AD9967 , v0122
Registered to: MURALI

Connect phone on selected interface...

Core : v2.26 , NXP FlashEngine : v5.3

Flash Mode : Full Update (System, User, Boot)
Check and select files according selected FlashMode

Ok, Set : RM980_1.2.4.3_059T985_IMEA_IN_variant.img
Ok, Set : RM980_1.2.4.3_boot.img
Ok, Set : RM980_1.2.4.3_cache.img
Ok, Set : RM980_1.2.4.3_emmc_appsboot.mbn
Ok, Set : RM980_1.2.4.3_emmc_appsboothd.mbn
Ok, Set : RM980_1.2.4.3_fat.bin
Ok, Set : RM980_1.2.4.3_oemsbl.mbn
Ok, Set : RM980_1.2.4.3_oemsblhd.mbn
Ok, Set : RM980_1.2.4.3_persist.img
Ok, Set : RM980_1.2.4.3_preload.img
Ok, Set : RM980_1.2.4.3_qcsbl.mbn
Ok, Set : RM980_1.2.4.3_qcsblhd_cfgdata.mbn
Ok, Set : RM980_1.2.4.3_recovery.img
Ok, Set : RM980_1.2.4.3_system.img
Ok, Set : RM980_1.2.4.3_udisk.bin
Ok, Set : RM980_1.2.4.3_userdata.img

File HW revision is : HW Revision V1

Dead Mode is Selected
1. Phone should be Off!
2. Press and hold 'Volume Down' button
3. Insert USB cable and hold button, until phone will be detected


Connect Ok

Get Phone Initial Info
Product : MSM7627A
Version : 0.5
Serial : 4DCD647

Processing : RM980_1.2.4.3_qcsblhd_cfgdata.mbn
Init Ok, send data ...
Data sent, start flashing
Region Flash Done
Processing : RM980_1.2.4.3_qcsbl.mbn
Init Ok, send data ...
Data sent, start flashing
Region Flash Done
Processing : RM980_1.2.4.3_oemsblhd.mbn
Init Ok, send data ...
Data sent, start flashing
Region Flash Done
Processing : RM980_1.2.4.3_oemsbl.mbn
Init Ok, send data ...
Data sent, start flashing
[Info] : INFOhasHead == true!
Region Flash Done
Processing : RM980_1.2.4.3_emmc_appsboothd.mbn
Init Ok, send data ...
Data sent, start flashing
Region Flash Done
Processing : RM980_1.2.4.3_emmc_appsboot.mbn
Init Ok, send data ...
Data sent, start flashing
[Info] : INFOhasHead == true!
Region Flash Done
Processing : RM980_1.2.4.3_boot.img
Init Ok, send data ...
Data sent, start flashing
Region Flash Done
Processing : RM980_1.2.4.3_recovery.img
Init Ok, send data ...
Data sent, start flashing
Region Flash Done
Processing : RM980_1.2.4.3_persist.img
Init Ok, send data ...
Data sent, start flashing
Region Flash Done
Processing : RM980_1.2.4.3_fat.bin
Init Ok, send data ...
Data sent, start flashing
Region Flash Done
Processing : RM980_1.2.4.3_system.img
Init Ok, send data ...
Data sent, start flashing
Region Flash Done
Processing : RM980_1.2.4.3_cache.img
Init Ok, send data ...
Data sent, start flashing
Region Flash Done
Processing : RM980_1.2.4.3_userdata.img
Erase Partition : USERDATA
Partition Erase Done
Init Ok, send data ...
Data sent, start flashing
Region Flash Done
Processing : RM980_1.2.4.3_udisk.bin
Init Ok, send data ...
Data sent, start flashing
Region Flash Done
Processing : RM980_1.2.4.3_preload.img
Init Ok, send data ...
Data sent, start flashing
Region Flash Done
Processing : RM980_1.2.4.3_059T985_IMEA_IN_variant.img
Init Ok, send data ...
Data sent, start flashing
Region Flash Done
Rebooting phone now

Flashing done!
Total flash time : 00:05:09
Reboot phone Ok

Connect phone on selected interface...

Phone found!
Nokia X Platform Phone detected (ADB)
Read info... Ok

sany5491 03-28-2017 14:54

Nokia XL RM-1030 Flashing done by BEST

Code:

Core : v2.26 , NXP FlashEngine : v5.3

Flash Mode : Full Update (System, User, Boot)
Check and select files according selected FlashMode

Ok, Set : RM1030_1.2.3.1_059V935_IMEA_BD_variant.img
Ok, Set : RM1030_1.2.3.1_boot.img
Ok, Set : RM1030_1.2.3.1_cache.img
Ok, Set : RM1030_1.2.3.1_emmc_appsboot.mbn
Ok, Set : RM1030_1.2.3.1_emmc_appsboothd.mbn
Ok, Set : RM1030_1.2.3.1_fat.bin
Ok, Set : RM1030_1.2.3.1_oemsbl.mbn
Ok, Set : RM1030_1.2.3.1_oemsblhd.mbn
Ok, Set : RM1030_1.2.3.1_persist.img
Ok, Set : RM1030_1.2.3.1_preload.img
Ok, Set : RM1030_1.2.3.1_qcsbl.mbn
Ok, Set : RM1030_1.2.3.1_qcsblhd_cfgdata.mbn
Ok, Set : RM1030_1.2.3.1_recovery.img
Ok, Set : RM1030_1.2.3.1_system.img
Ok, Set : RM1030_1.2.3.1_udisk.bin
Ok, Set : RM1030_1.2.3.1_userdata.img

File HW revision is : HW Revision V1

Dead Mode is Selected
1. Phone should be Off!
2. Press and hold 'Volume Down' button
3. Insert USB cable and hold button, until phone will be detected


Connect Ok

Get Phone Initial Info
Product : MSM7627A
Version : 0.5
Serial  : 41DB698

Processing : RM1030_1.2.3.1_qcsblhd_cfgdata.mbn
Init Ok, send data ...
Data sent, start flashing
Region Flash Done
Processing : RM1030_1.2.3.1_qcsbl.mbn
Init Ok, send data ...
Data sent, start flashing
Region Flash Done
Processing : RM1030_1.2.3.1_oemsblhd.mbn
Init Ok, send data ...
Data sent, start flashing
Region Flash Done
Processing : RM1030_1.2.3.1_oemsbl.mbn
Init Ok, send data ...
Data sent, start flashing
[Info] : INFOhasHead == true!
Region Flash Done
Processing : RM1030_1.2.3.1_emmc_appsboothd.mbn
Init Ok, send data ...
Data sent, start flashing
Region Flash Done
Processing : RM1030_1.2.3.1_emmc_appsboot.mbn
Init Ok, send data ...
Data sent, start flashing
[Info] : INFOhasHead == true!
Region Flash Done
Processing : RM1030_1.2.3.1_boot.img
Init Ok, send data ...
Data sent, start flashing
Region Flash Done
Processing : RM1030_1.2.3.1_recovery.img
Init Ok, send data ...
Data sent, start flashing
Region Flash Done
Processing : RM1030_1.2.3.1_persist.img
Init Ok, send data ...
Data sent, start flashing
Region Flash Done
Processing : RM1030_1.2.3.1_fat.bin
Init Ok, send data ...
Data sent, start flashing
Region Flash Done
Processing : RM1030_1.2.3.1_system.img
Init Ok, send data ...
Data sent, start flashing
Region Flash Done
Processing : RM1030_1.2.3.1_cache.img
Init Ok, send data ...
Data sent, start flashing
Region Flash Done
Processing : RM1030_1.2.3.1_userdata.img
Erase Partition : USERDATA
Partition Erase Done
Init Ok, send data ...
Data sent, start flashing
Region Flash Done
Processing : RM1030_1.2.3.1_udisk.bin
Init Ok, send data ...
Data sent, start flashing
Region Flash Done
Processing : RM1030_1.2.3.1_preload.img
Init Ok, send data ...
Data sent, start flashing
Region Flash Done
Processing : RM1030_1.2.3.1_059V935_IMEA_BD_variant.img
Init Ok, send data ...
Data sent, start flashing
Region Flash Done
Rebooting phone now

Flashing done!
Total flash time : 00:05:42
Reboot phone Ok


sany5491 03-28-2017 14:57

Nokia 220 hnag on Logo done by formate
Code:

Dead Mode is Selected
Waiting for USB device...
1. Phone should be Off!
2. Battery must be charged and inserted! ( if not used external power )
 - > If phone can't switch to BL - use battery or flash from Local mode!

--- Insert USB cable now! ---
Wait for phone...
Phone found! [ 22 ]
Sync...
Sync Ok, read regs...
Inital regs read done
Boot Info :
BB_CPU_ID : 625A
BB_CPU_HW : CA01
BB_CPU_SW : 0001
BB_CPU_SB : 8000
BB_CPU_NM : [MediaTek] MT6250_S0001
BB_CPU_SN : FBE5143BEF1BAF5BAE79D477EB9AB76B
BROM Protocol Version : 05
BROM Status : 1012
Comm Status : 0000
EXBL Status : Alive [ USB Load Active ]
Switch to BL done
BL Version : 01
Setting...
Setting done , result code 0x8000
Project ID : Rivendell.10.03.11.p1
BROM/BL stage done
Seek and prepare DownloadAgent
DownloadAgent matching HW Found!
DA verify and select done
Sending DA to target ...
DA_eMP_Rivendell.fg
DA_VERIFY : 00
DA_JUMP  : 00040000
DA_AUTH  : Passed!
DA_INFO  : 0xC0 , Ver : 3.2 , BBID : 0x88
DA_CSTAT  : 0x5A
SOC_VERIFY : 0xC1
BOOT_STYLE : SF_FLASH_BOOT
NOR Flash IC initialized
[0] : FLASH_VEN : 0x00F8 , [WINBOND] W25Q128FW
[0] : FLASH_DIE : 00EF 0060 0018 0000
[0] : FLASH_LEN : 0x01000000
FAT_RANGE : 0x00A60000-0x00FF3FFF , LEN : 0x00594000

Executing FFS FORMAT now...
FAT_RANGE : 0x00A60000-0x00FF3FFF , LEN : 0x00594000
DA_RET  : DA_IN_PROGRESS
DA_RET  : FORMAT_DONE

Elapsed: 00:01:43
Connect phone on selected interface...


sany5491 03-28-2017 15:16

RM-917 (LUMIA 521) Flash done by BEST.

Code:

Core : v2.26 , WP10x FlashEngine : v3.0

FFU : RM917_1030.6409.1311.0001_RETAIL_nam_usa_216_01_170918_prd_signed.ffu
Checking FFU file, wait...
FFU Revision ID  : 2.0
FFU Model ID      : Nokia.MSM8227.P6037
FFU RootKeyHash  : 9DF6E11153C33AA85F7984C21EFA43AEDF9B82BE
FFU Languages    : Albanian , Arabic , Azerbaijan(Latin) , Belorusian , Bulgarian , Catalan , Croatian , Czech , Danish (Denmark) , Dutch (Netherlands) , English (UK) , English , Estonian , Filipino (Philippines) , Finnish , French , German , Greek , Hwbre (Israel) , Hindi (India) , Hungarian , Indonesian , Italian , Japanese , Kazakh , Korean , Latvian , Lithuanian , Macedonian , Malay (Malaysia) , Norwegian (Bokmal , Norway) , Persian (Iran) , Polish , Portuguese(Brazil) , Portuguese(Portugal) , Romanian , Russian , Serbian (Latin) , Chinese , Slovak , Slovenian , Spanish(Mexico) , Spanish , Swedish , Thai , Chinese(Taiwan) , Turkish , Ukrainian , Uzbekistan(Latin) , Vietnamese ,
FFU ChipSectors  : 7557120
FFU Header        : 0x000C0000
FFU Payload      : 0x4D020000
FFU FastVerify    : Ok

Waiting for phone...
Dead mode is selected , no phone in normal mode found
1. Press and hold "Volume Down"
2. Insert USB cable
3. Hold button until phone will be detected

Device catched in BOOT mode!
Boot Mode confirmed!
Setting Preloder
Collect Info...
Setting Application
Setting Secure
Collect Info...
=== Nokia Flash App info :
Protocol Version        : 1.15
Protocol Implementation : 1.28
=== Phone Initial info :
Phone RMxxx ID : RM-917
Phone Model ID : Nokia.MSM8227.P6037.1.2
Phone Model PC : 059S0B4
Phone IMEI    : 355913058553657
=== eMMC info :
eMMC Vendor : Hynix
eMMC CID : 0090
eMMC Size : 7400 MiB
=== Security Initial info :
Security Status  : 010100000101
Secure Boot : Enabled
Secure eFUSE : Enabled
JTAG : Disabled
RDC Key : Not Present (Retail)
UEFI SBoot : Enabled
SecHW Key : Exists
Device RootKey    : 9DF6E11153C33AA85F7984C21EFA43AEDF9B82BE
=== Other info :
SD present        : True , 00983A00

Full Check skipped , will be checked by ImageSignature


Battery Level : 76%
RPMB Provision Status Code : 0x0101
Device RAM size : 512 MiB
Device not have ATRP
Backup to RAM Ok!

FFU : RM917_1030.6409.1311.0001_RETAIL_nam_usa_216_01_170918_prd_signed.ffu
Flashing FFU
Sending FFU Header CertData
Header sent , accepted :)
Perform Data Partition Erase
Erase done
Sending FFU Payload Data...
Finishing flashing

Flashing done!
Green Light :)

Image Sent, processing PostFlash
FinalConfig : abnormal status, error code : 0xFFFF0000
Make Factory Set : Ok
Restore RAMBkp : Ok
PostFlash Finished

Total flash time : 00:02:48

Rebooting

Connect phone on selected interface...


gsmjiya 03-30-2017 06:49

lumia 640 lte rm-1073 unlock done by best dongel
 
[WP8x] : Init TesMode
[TSTM] : Use File : RM1073_2179.0000.9651.15153.207.760_enosw-wim-signed_858223.secwim
=== Base Phone Info
Sw Version : 02166.00000.15103.45022
IMEI : 3578********
ProductCode : 059X0B6
Device catched in BOOT mode!
Collect Info...
=== Nokia Flash App info :
Protocol Version : 2.37
Protocol Implementation : 2.60
=== Phone Initial info :
Phone Model ID : Nokia.MSM8926.P6204.1.1
=== eMMC info :
eMMC Vendor : Samsung
eMMC CID : 0015
eMMC Size : 7456 MiB
=== Security Initial info :
Security Status : 010100000101
Secure Boot : Enabled
Secure eFUSE : Enabled
JTAG : Disabled
RDC Key : Not Present (Retail)
UEFI SBoot : Enabled
SecHW Key : Exists
Device RootKey : 831BE6B18E7006372069545885A80F786C33D064
=== Other info :
SD present : False

SECWIM : RM1073_2179.0000.9651.15153.207.760_enosw-wim-signed_858223.secwim
Sending WIM ...

WIM Image sent! Trying init TestMode now...

Connect phone on selected interface...

Phone found!
WP10/WP8x Lumia Phone detected
Read info... Ok

=== Main info ===
SecLabel Version : Security LabelSW (wim) 20.2169.385.194
Sw Version : RM1073 2179.0000.9651.15153 858223 2015/08/03 //romulus_engine/asset_integration_RG2\r\n
IMEI : 3578*********
ProductCode : 059X0B6
ProductSN : DFD4B00AU
Module Code : 0206634
=== HW info ===
Public ID : 9ADD16358BDF7CA842B7232941A3A50031AF1126
BT Addr. : 300D4355F7BD
Wlan Mac : 300D438F9D40
=== Branding and security info ===
Sec. Mode : Restricted

Conf key : 8000000000000000
Provider key : 3101500112987633
Country : United States of America
Operator : AT&T
Counters : Key 0 [3] , Fbus 0 [10]
Blocks : 3

LOCK STATUS :
=============================
BLK : 1
Lock1:Close
BLK : 2
Lock1:Close
BLK : 3
Lock1:Close
=============================
LOCKS : Closed
=============================

Making RPL backup...
NPC : Read Ok , [520]
IMEI : 3578*******
CCC : Certificate not available
HWC : Certificate not available
RDC : Certificate not available

NPC Certificate saved...

RPL saved : C:\InfinityBox\BEST\Backup\Cert\3578*******_CRT_2n d.rpl

Done!

WP8 Unlock Started
Connecting to server...
Connected
Authenticating...
Authenticated
Checking Client version...
Client version is valid
Processing Step #1
Processing Step #2
Processing Step #3
Processing Step #4
Disconnected
Need SDAuth to finish ...
Started
Connecting to SX4 server...
Connected
SX4 enter ..
SDAuth Ok!
SX4 Disconnected
Unlock Done!
Wait for phone reboot ...
Reboot Ok!

Phone disconected!

Connect phone on selected interface...

Phone found!
WP10/WP8x Lumia Phone detected
Read info... Ok

=== Main info ===
NCSD Version : 5.0
Sw Version : 02166.00000.15103.45022
IMEI : 35***********
ProductCode : 059X0B6
ProductCodeB : 059W8Z1
ProductSN : DFD4B00AU
Module Code : 0206634
=== HW info ===
Public ID : 9ADD16358BDF7CA842B7232941A3A50031AF1126
HW Version : 2140
BT Addr. : 300D4355F7BD
Wlan Mac : 300D438F9D40
Battery Level : 24 %
=== Branding and security info ===
Operator : AIO-US
SimLock : Unlocked
SimLock : 2440700000000
Country : Finland
Operator : NOKIA (Open)
Branding : RM-1073_1002
Sec. Mode : Restricted
Done!
thanks infinity best .............

-Mosin- 04-05-2017 13:02

Lumia 625 Unlock Done.
 
Nokia lumia 625 Direct unlock.


http://oi68.tinypic.com/2i24djr.jpg



Phone found!
WP10/WP8x Lumia Phone detected
Read info... Ok

WP8 Unlock Started
Connecting to server...
Connected
Authenticating...
Authenticated
Checking Client version...
Client version is valid
Processing Step #1
Processing Step #2
Processing Step #3
Processing Step #4
Disconnected
Need SDAuth to finish ...
Started
Connecting to SX4 server...
Connected
SX4 enter ..
SDAuth Ok!
SX4 Disconnected
Unlock Done!
Wait for phone reboot ...
Reboot Ok!

Phone disconected!

Connect phone on selected interface...

Phone found!
WP10/WP8x Lumia Phone detected
Read info... Ok


4G Telecom 04-19-2017 06:53

Nokia dct 4 (2760) Unlock Done

Read Info..............
Code:

Reading Phone Info....
SW ver  : V 05.61 18-04-08 RM-258 (c) Nokia
IMEI    :      356XXXXXXXXXXXX
PPM    :      V 05.61
18-04-08
RM-258
(c) Nokia
AG
CNT    :      Content: ag_yoigo_es_red
V 05.61
18-04-08
RM-258
(c) Nokia


DSP Ver :      6w45.v48
PCode  :      0572417
BPCode  :      0515047
HWID    :      5000
LCDVer  :      SUEZ
IMEI    :      356XXXXXXXXXXXX
Sl Conf  : 214-04-00086388183
Sl Prof  : 800000000001000-B
Sl Aux  : 000B5555
Hw Sig  : 293514D1D57EACEE
Country      : Spain
Operator    : Yoigo

Lock info:
Block 1
L1:Close; 

Done!

Unlocking..........
Code:

Write SL RPL procedure procedure started...
Read Lock Info
Locked to Unknown providers
Unlocking...
All done !

After Unlock Read Info..........
Code:

Reading Phone Info....
SW ver  : V 05.61 18-04-08 RM-258 (c) Nokia
IMEI    :      356802026021393
PPM    :      V 05.61
18-04-08
RM-258
(c) Nokia
AG
CNT    :      Content: ag_yoigo_es_red
V 05.61
18-04-08
RM-258
(c) Nokia


DSP Ver :      6w45.v48
PCode  :      0572417
BPCode  :      0515047
HWID    :      5000
LCDVer  :      SUEZ
IMEI    :      356XXXXXXXXXXXX
Sl Conf  : 001-01-00000000000
Sl Prof  : 000000000001000-B
Sl Aux  : 000B5555
Hw Sig  : 293514D1D57EACEE
Country      : Test SIM (Open)
Operator    : NOKIA (Open)

Lock info:
Block 1
L1:Open;  L2:Open;  L3:Open;  L4:Open;  L5:Open; 
Block 2
L1:Open;  L2:Open;  L3:Open;  L4:Open;  L5:Open; 
Block 3
L1:Open;  L2:Open;  L3:Open;  L4:Open;  L5:Open; 
Block 4
L1:Open;  L2:Open;  L3:Open;  L4:Open;  L5:Open; 
Block 5
L1:Open;  L2:Open;  L3:Open;  L4:Open;  L5:Open; 
Block 6
L1:Open;  L2:Open;  L3:Open;  L4:Open;  L5:Open; 
Block 7
L1:Open;  L2:Open;  L3:Open;  L4:Open;  L5:Open; 

Done!


profkefah 04-23-2017 19:36

Nokia 150 rm1190 screen lock reset done
 
Nokia 150 rm1190 screen lock reset done


Quote:

Dead Mode is Selected
Waiting for USB device...
1. Phone should be Off!
2. Battery must be charged and inserted! ( if not used external power )
- > If phone can't switch to BL - use battery or flash from Local mode!

--- Insert USB cable now! ---
Wait for phone...
Phone found! [ 141 ]
Sync...
Sync Ok, read regs...
Inital regs read done
Boot Info :
BB_CPU_ID : 6261
BB_CPU_HW : CB01
BB_CPU_SW : 0001
BB_CPU_SB : 8000
BB_CPU_NM : [MediaTek] MT6261_S0001
BB_CPU_SN : C298A57EA7F89DCBF4D96C91FCE3F54D
BROM Protocol Version : 05
BROM Status : 0000
Comm Status : 0000
EXBL Status : Alive [ USB Load Active ]
Switch to BL done
BL Version : 01
Setting...
BROM/BL stage done
MT626x : Reset User Code
All done! Remove USB cable
All Security Settings deactivated!
Code set to default : 12345
Done!
Connect phone on selected interface...


Luckey1 04-26-2017 09:38

Nokia 210
 
Code:

Core : v2.28 , BB5XG FlashEngine : v10.5

Selected FlashSettings : Manual
Check FlashFiles, Please, wait...

Files Set for Flashing :
MCU : rm924__06.09.mcusw
PPM : rm924__06.09.ppm_ma3
CNT : rm924__06.09.image_ma3_059R775
Flashing phone now...
[Gen] Rules accepted for : XGOLD Generation
Check files done...
-> SWversion check skipped : Dead mode selected
Dead Mode is Selected
Waiting for USB device...

-> If Windows say "Unrecognized device" / Operation not start
-> Or if Phone start charge - just reinsert battery
-> If flashing freeze - reinsert cable/battery and try again
--- Press phone's power button or insert usb cable! ---

Connection opened successfully

IF Boot Init : 0xF0
IF Resp Len  : 0x0A
IF xCPUID    : XGOLD 213 [XMM2130 QUANTUM]
IF Resp Data  :  1FB300020303010100FF

Sending EBL Loader ...
EBL Loader Ok, 01
EBL Loader ready, AA
Sending EBL ...
EBL sent Ok
EBL : Quantum_Bootloader_10.56_M1S1
Speed accepted, use 6.500.000
FLASHID : EC001230
FLIC conf set, RST set
Boot done!

Check keys...
Check done. Image can be flashed

Backup enabled, will read all certificates

Reading CCC
Reading HWC
Reading NPC

IMEI 1 : 357897058842905
IMEI 2 : 357897058842913
PCcode : 059R776

NPC Certificate saved...
CCC Certificate saved...
HWC Certificate saved...

RPL saved : C:\InfinityBox\BEST\Backup\Cert\357897058842905_XG213_CRT.rpl

Settings : EDM [0x8] , Block Mode , Fast CRC , Verify

  ===Flashing [MCU]===
File : rm924__06.09.mcusw
Image : rm924__06.09.mcusw_ebl_psi.fls
Sec-pack found, sending ...
Sec-pack sent
Found 5 region(s)
Processing Region 1/5
Erase , Start : 0x40000000 , Len : 0x00020000
Erasing, wait ...
Erase done, time : 00:00:00
Write , Start : 0x40000000 , Len : 0x00020000
Flashing , wait ...
Region flash done, time : 00:00:00
Processing Region 2/5
Erase , Start : 0x40040000 , Len : 0x00020000
Erasing, wait ...
Erase done, time : 00:00:00
Write , Start : 0x40040000 , Len : 0x00020000
Flashing , wait ...
Region flash done, time : 00:00:00
Processing Region 3/5
Erase , Start : 0x40060000 , Len : 0x00100000
Erasing, wait ...
Erase done, time : 00:00:02
Write , Start : 0x40060000 , Len : 0x00100000
Flashing , wait ...
Region flash done, time : 00:00:01
Processing Region 4/5
Erase , Start : 0x40280000 , Len : 0x01A40000
Erasing, wait ...
Erase done, time : 00:00:54
Write , Start : 0x40280000 , Len : 0x01A40000
Flashing , wait ...
Region flash done, time : 00:00:38
Processing Region 5/5
Erase , Start : 0x43E20000 , Len : 0x00040000
Erasing, wait ...
Erase done, time : 00:00:00
No write data, skip
[Minor Error] : CRC returned by phone is wrong!
[CHK] : 0100E361

  ===Flashing [PPM]===
File : rm924__06.09.ppm_ma3
Image : package_ma3.ppm_ebl_psi.fls
Sec-pack found, sending ...
Sec-pack sent
Found 1 region(s)
Processing Region 1/1
Erase , Start : 0x41CC0000 , Len : 0x00640000
Erasing, wait ...
Erase done, time : 00:00:08
Write , Start : 0x41CC0000 , Len : 0x003EFB64
Flashing , wait ...
Region flash done, time : 00:00:04
CRC check passed , 0x44C0

  ===Flashing [CNT]===
File : rm924__06.09.image_ma3_059R775
Image : package_ma3_059R775.image.fls
Sec-pack found, sending ...
Sec-pack sent
Found 2 region(s)
Processing Region 1/2
Erase , Start : 0x42300000 , Len : 0x01B20000
Erasing, wait ...
Erase done, time : 00:01:05
Write , Start : 0x42300000 , Len : 0x00C60000
Flashing , wait ...
Region flash done, time : 00:00:16
Processing Region 2/2
Erase , Start : 0x43E60000 , Len : 0x000E0000
Erasing, wait ...
Erase done, time : 00:00:02
No write data, skip
CRC check passed , 0x98EC

Flashing done!
Total flash time : 00:03:14
Reboot phone now...

Reading Phone Info....
Connected phone -  Nokia 210
Software Info:    V 06.09 14-10-13 RM-924 (c) Nokia           
IMEI:  357897058842905
PPM version :  V 06.09 14-10-13 RM-924 (c) Nokia            MA3
Product code:  059R776
Wait, when phone will be ready ...
Checking...
SimLock status : SimLock is Ok
Security status : Security is Ok
Read Info Done!
Check and Upload User Certificates ...
Total - 58 certs
Certificates found, skip upload ...
Battery voltage is enough for start
AfterFlash operations done ;D
Done!
Connect phone on selected interface...


Elapsed: 00:04:22


syed tuqeer 04-26-2017 10:16

Nokia X2-01 Read User Code Done :)
 
Code:

Connect phone on selected interface...

Backup Certificates now...
Dead Mode is Selected
Waiting for USB device...
--- Insert cable and charger or press phone's power button! ---
Connection opened successfully
Waiting for communication response...
[BootRom] : 1st boot Ok!
ASIC ID:      000000000000000022000509200C0000
CPU ID :      BroadCom 21351 , Features : Dead-Test, USBRPL, FullUSB
EM0 ID:        00005361
PUBLIC ID:    0000000000B4358CA7CC9A46172887BECC08807B
ASIC MODE ID:  00
ROOT KEY HASH: 1B0D74C532CA1C6133940C740E8C786E
ROM ID:        DE56D582BDDE7A3A
Use BCM21351_usb2nd.fg  ,  Rev : 2.1  Ver : 12.8.0
Processing RAWLOADER...
FLIC : 00300020
Req : XSR 1.6
Use BCM21351_XSR16_usbalg.fg  ,  Rev : 2.1  Ver : 12.8.0
Processing PASUBTOC ...
Processing ALG ...
Boot Done! :)
TIME : Boot time : 00:00:01
Reopening the connection...
Waiting for response: 30
ADL: Check mode
Select ASIC [C900]
PAPUBkeys : 37955B6FC432998EF0DB240E332228384D19ED09
ADL: Reading certificates...

Reading NPC certificate...
IMEI : 357915040391516
Reading CCC certificate...
Reading HWC certificate...
Reading R&D certificate...
Reading VARIANT certificate...
Reading PARTNERC certificate...
Reading MDM_KEYS certificate...
ADL: Reading certificates done! :)
ADL: Close_Session
Content: 000300000000000000000000000000
ADL: Reboot

Wait, reconneting...

SLx Simlock Data read ... Ok
SL3 Simlock Sign read ... Ok
CMLA Key read ... Ok
WMDRM read ... Ok
CRT308 Backup Created
NPC Certificate saved...
CCC Certificate saved...
HWC Certificate saved...
SimLock Data saved...
SimLock Key saved...
WMDRM_PD Data saved...
CMLA_KEY Data saved...

RPL saved : F:\1+Flashing Software\1+Infinity Box\BEST\Backup\Cert\357915040391516.rpl

All done, Disconnecting

Elapsed: 00:00:49
Connect phone on selected interface...


Phone found!
Series 40 Device detected!
read info...  - Ok

Reading Phone Info....
Connected phone -    X2-01
Software ver : V 07.11 22-12-10 RM-709 (c) Nokia           
IMEI    :      357915040391516
XappVer :      000008E8
PPM    :      V 07.11 22-12-10 RM-709 (c) Nokia            MC
CNT    :      Content: mc_059C351 V 07.11 22-12-10 RM-709 (c) Nokia           
Product SN  :    1F1495CAH
Product code :    059C351
Base Prd.code:    059B859
Module code  :    0204674
Long Prod.SN :    0
Hardware info=======
HWID  : 1001
Battery: 3742 mV
CMT BT: 2.31-SP2.31
LCDVer: SEIKO
Lock info ===========
IMEI      : 357915040391516
IMEI spNet : 3A 75 19 05 04 93 51 01
IMEI svNet : 33 75 19 05 04 93 51 21 F9

Conf key    : 0000000000000000
Provider key : 2440700000000000
Country      : Finland
Operator    : NOKIA (Open)
Counters    : Key 0  [3] , Fbus 0  [10]
Blocks      : 7

LOCK STATUS :
=============================
BLK : 1
 Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 2
 Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 3
 Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 4
 Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 5
 Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 6
 Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 7
 Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
=============================
LOCKS :  All Open
=============================
Error collect lock info, try again
CRT308 Backup Created

SDD key status : Ok
CMLA Key status : Ok
SimLock status : Ok
Security status : Ok
PA_SimLock Version :
PA_SL3 phone ,  SP_CODE_LEN : 15

User Code : 33633
MMC pwd  : Backup saved
UserDataExLevel : Full [PhoneBook, Calendar, PWD, SMS, Gallery]

Done!

Reading MMC password...
MMC pass Record found, saving...
1 MMC pwd records are found! Extracting...
-------------------------------
We have next Pass: aaaaa
-------------------------------
Done!

Set phone in Normal mode...
Restarting...
Done!

Phone disconected!

Connect phone on selected interface...


Luckey1 04-26-2017 15:40

Nokia 110
 
Code:

Core : v2.28 , BB5XG FlashEngine : v10.5

Selected FlashSettings : Manual
Check FlashFiles, Please, wait...

Files Set for Flashing :
MCU : rm827__03.51.mcusw
PPM : rm827__03.51.ppm_m2
CNT : rm827__03.51.image_m2_059N2R0
Flashing phone now...
[Gen] Rules accepted for : XGOLD Generation
Check files done...
-> SWversion check skipped : Dead mode selected
Dead Mode is Selected
Waiting for USB device...

-> If Windows say "Unrecognized device" / Operation not start
-> Or if Phone start charge - just reinsert battery
-> If flashing freeze - reinsert cable/battery and try again
--- Press phone's power button or insert usb cable! ---

Connection opened successfully

IF Boot Init : 0xF0
IF Resp Len  : 0x0A
IF xCPUID    : XGOLD 213 [XMM2130 QUANTUM]
IF Resp Data  :  1FB300020303010100FF

Sending EBL Loader ...
EBL Loader Ok, 01
EBL Loader ready, AA
Sending EBL ...
EBL sent Ok
EBL : Quantum_Bootloader_10.49_M1S1
Speed accepted, use 6.500.000
FLASHID : 89008289
FLIC conf set, RST set
Boot done!

Check keys...
Check done. Image can be flashed

Backup enabled, will read all certificates

Reading CCC
Reading HWC
Reading NPC

IMEI 1 : 359981058150580
IMEI 2 : 359981058150598
PCcode : 059N403

NPC Certificate saved...
CCC Certificate saved...
HWC Certificate saved...

RPL saved : C:\InfinityBox\BEST\Backup\Cert\359981058150580_XG213_CRT.rpl

Settings : EDM [0x8] , Block Mode , Fast CRC , Verify

  ===Flashing [MCU]===
File : rm827__03.51.mcusw
Image : rm827__03.51.mcusw_ebl_psi.fls
Sec-pack found, sending ...
Sec-pack sent
Found 5 region(s)
Processing Region 1/5
Erase , Start : 0x40000000 , Len : 0x00020000
Erasing, wait ...
Erase done, time : 00:00:00
Write , Start : 0x40000000 , Len : 0x00020000
Flashing , wait ...
Region flash done, time : 00:00:00
Processing Region 2/5
Erase , Start : 0x40040000 , Len : 0x00020000
Erasing, wait ...
Erase done, time : 00:00:01
Write , Start : 0x40040000 , Len : 0x00020000
Flashing , wait ...
Region flash done, time : 00:00:00
Processing Region 3/5
Erase , Start : 0x40060000 , Len : 0x00100000
Erasing, wait ...
Erase done, time : 00:00:05
Write , Start : 0x40060000 , Len : 0x00100000
Flashing , wait ...
Region flash done, time : 00:00:01
Processing Region 4/5
Erase , Start : 0x40280000 , Len : 0x01940000
Erasing, wait ...
Erase done, time : 00:02:16
Write , Start : 0x40280000 , Len : 0x018C0000
Flashing , wait ...
Region flash done, time : 00:00:34
Processing Region 5/5
Erase , Start : 0x43E20000 , Len : 0x00040000
Erasing, wait ...
Erase done, time : 00:00:00
No write data, skip
CRC check passed , 0xA3D6

  ===Flashing [PPM]===
File : rm827__03.51.ppm_m2
Image : package_m2.ppm_ebl_psi.fls
Sec-pack found, sending ...
Sec-pack sent
Found 1 region(s)
Processing Region 1/1
Erase , Start : 0x41BC0000 , Len : 0x00600000
Erasing, wait ...
Erase done, time : 00:00:16
Write , Start : 0x41BC0000 , Len : 0x0030F748
Flashing , wait ...
Region flash done, time : 00:00:05
CRC check passed , 0x4605

  ===Flashing [CNT]===
File : rm827__03.51.image_m2_059N2R0
Image : package_m2_059N2R0.image.fls
Sec-pack found, sending ...
Sec-pack sent
Found 2 region(s)
Processing Region 1/2
Erase , Start : 0x421C0000 , Len : 0x01C60000
Erasing, wait ...
Erase done, time : 00:04:28
Write , Start : 0x421C0000 , Len : 0x00F20000
Flashing , wait ...
Region flash done, time : 00:00:24
Processing Region 2/2
Erase , Start : 0x43E60000 , Len : 0x000E0000
Erasing, wait ...
Erase done, time : 00:00:08
No write data, skip
CRC check passed , 0x7408

Flashing done!
Total flash time : 00:08:24
Reboot phone now...

Reading Phone Info....
Connected phone -  Nokia 110
Software Info:    V 03.51 06-08-13 RM-827 (c) Nokia           
IMEI:  359981058150580
PPM version :  V 03.51 06-08-13 RM-827 (c) Nokia            M2
Product code:  059N403
Wait, when phone will be ready ...
Checking...
SimLock status : SimLock is Ok
Security status : Security is Ok
Read Info Done!
Processing After Flash Defaults...
FullFactorySet... Ok!
UserDataDefaultsSet...OK!
ServiceDefaultsSet... Ok!
LeaveDefaultsSet... Ok!
ProductTuneSet...OK!
SwUpgradeSet...OK!
Check and Upload User Certificates ...
Total - 58 certs
Certificates found, skip upload ...
AfterFlash operations done ;D
Done!
Connect phone on selected interface...


Elapsed: 00:09:28


naje 04-27-2017 04:47

lumia 650 rm1152 unlock don
 
[WP8x] : Init TesMode
[TSTM] : Use File : RM1152_1078.0021.10586.13053.207.331_enosw-wim-signed_516102.secwim
=== Base Phone Info
Sw Version : 01078.00037.16082.41002
IMEI : 35512607830xxx
ProductCode : M1012174-001
Device catched in BOOT mode!
Collect Info...
=== Nokia Flash App info :
Protocol Version : 2.41
Protocol Implementation : 2.75
=== Phone Initial info :
Phone Model ID : Microsoft.MSM8909.P6237.2.0
=== eMMC info :
eMMC Vendor : Samsung
eMMC CID : 0015
eMMC Size : 14910 MiB
=== Security Initial info :
Security Status : 010100000101
Secure Boot : Enabled
Secure eFUSE : Enabled
JTAG : Disabled
RDC Key : Not Present (Retail)
UEFI SBoot : Enabled
SecHW Key : Exists
Device RootKey : B8219CA0F88F67C2EF5C16BE975B61705FA14D95
=== Other info :
SD present : False

SECWIM : RM1152_1078.0021.10586.13053.207.331_enosw-wim-signed_516102.secwim
Sending WIM ...

WIM Image sent! Trying init TestMode now...

Connect phone on selected interface...

Phone found!
WP10/WP8x Lumia Phone detected
Read info... Ok

Check SimLock info

Conf key : 8000000000000000
Provider key : 2280100000000000
Country : Switzerland
Operator : Swisscom
Counters : Key 0 [3] , Fbus 0 [10]
Blocks : 1

LOCK STATUS :
=============================
BLK : 1
Lock1:Close
=============================
LOCKS : Closed
=============================

Done!

WP8 Unlock Started
Connecting to server...
Connected
Authenticating...
Authenticated
Checking Client version...
Client version is valid
Processing Step #1
Processing Step #2
Processing Step #3
Processing Step #4
Disconnected
Need SDAuth to finish ...
Started
Connecting to SX4 server...
Connected
SX4 enter ..
SDAuth Ok!
SX4 Disconnected
Unlock Done!
Wait for phone reboot ...
Reboot Ok!

rm1152 eno file https://we.tl/VbCEVutwcK

naje 04-27-2017 04:51

lumia 650 RM-1152 unlock success
 
[WP8x] : Init TesMode
[TSTM] : Use File : RM1152_1078.0021.10586.13053.207.331_enosw-wim-signed_516102.secwim
=== Base Phone Info
Sw Version : 01078.00037.16082.41002
IMEI : 355126078300724
ProductCode : M1012174-001
Device catched in BOOT mode!
Collect Info...
=== Nokia Flash App info :
Protocol Version : 2.41
Protocol Implementation : 2.75
=== Phone Initial info :
Phone Model ID : Microsoft.MSM8909.P6237.2.0
=== eMMC info :
eMMC Vendor : Samsung
eMMC CID : 0015
eMMC Size : 14910 MiB
=== Security Initial info :
Security Status : 010100000101
Secure Boot : Enabled
Secure eFUSE : Enabled
JTAG : Disabled
RDC Key : Not Present (Retail)
UEFI SBoot : Enabled
SecHW Key : Exists
Device RootKey : B8219CA0F88F67C2EF5C16BE975B61705FA14D95
=== Other info :
SD present : False

SECWIM : RM1152_1078.0021.10586.13053.207.331_enosw-wim-signed_516102.secwim
Sending WIM ...

WIM Image sent! Trying init TestMode now...

Connect phone on selected interface...

Phone found!
WP10/WP8x Lumia Phone detected
Read info... Ok

Check SimLock info

Conf key : 8000000000000000
Provider key : 2280100000000000
Country : Switzerland
Operator : Swisscom
Counters : Key 0 [3] , Fbus 0 [10]
Blocks : 1

LOCK STATUS :
=============================
BLK : 1
Lock1:Close
=============================
LOCKS : Closed
=============================

Done!

WP8 Unlock Started
Connecting to server...
Connected
Authenticating...
Authenticated
Checking Client version...
Client version is valid
Processing Step #1
Processing Step #2
Processing Step #3
Processing Step #4
Disconnected
Need SDAuth to finish ...
Started
Connecting to SX4 server...
Connected
SX4 enter ..
SDAuth Ok!
SX4 Disconnected
Unlock Done!
Wait for phone reboot ...
Reboot Ok!

eno file https://we.tl/VbCEVutwcK

Nasir Mobiles 04-27-2017 09:58

Nokia 130 (RM-1035) Blinking Repaired.

Write Firmware:
Code:

Core : v2.28 , MTKx FlashEngine : v12.0

Verify files ...
MAUI : RM-1035_ROM_eMP_10.01.11
VIVA : RM-1035_VIVA_eMP_10.01.11
LANG : RM-1035_LANG_PACK_ROM_IJ_eMP_10.01.11_001
CUST : RM-1035_CUSTPACK_ROM_IJ_MEA_PK_eMP_10.01.11_001
JMPT : RM-1035_JUMP_TABLE_IJ_MEA_PK_eMP_10.01.11_001
 - > MODE : FullFlash

Dead Mode is Selected
Waiting for USB device...
1. Phone should be Off!
2. Battery must be charged and inserted! ( if not used external power )
 - > If phone can't switch to BL - use battery or flash from Local mode!

--- Insert USB cable now! ---
Wait for phone...
Phone found! [ 256 ]
Sync...
Sync Ok, read regs...
Inital regs read done
Boot Info :
BB_CPU_ID : 6260
BB_CPU_HW : CB00
BB_CPU_SW : 0000
BB_CPU_SB : 8000
BB_CPU_NM : [MediaTek] MT6260_S0001
BB_CPU_SN : DD694703B9A9A599E9364BE1EFAE9197
BROM Protocol Version : 05
BROM Status : 0000
Comm Status : 0000
EXBL Status : Alive [ USB Load Active ]
Switch to BL done
BL Version : 01
Setting...
Setting done , result code 0x8000
Project ID : CRYSTAL.10.01.11.p2
BROM/BL stage done
Seek and prepare DownloadAgent
DownloadAgent matching HW Found!
DA verify and select done
Sending DA to target ...
DA_eMP_Crystal.fg
DA_VERIFY : 00
DA_JUMP  : 00040000
DA_AUTH  : Passed!
DA_INFO  : 0xC0 , Ver : 3.2 , BBID : 0x8B
DA_CSTAT  : 0x5A
SOC_VERIFY : 0xC1
BOOT_STYLE : SF_FLASH_BOOT
NOR Flash IC initialized
[0] : FLASH_VEN : 0x00E2 , [WINBOND] W25Q32BV
[0] : FLASH_DIE : 00EF 0040 0016 0000
[0] : FLASH_LEN : 0x00400000
FAT_RANGE : 0x003A4000-0x003F3FFF , LEN : 0x00050000
SecureDecrypt : RM-1035_ROM_eMP_10.01.11
SecureDecrypt : RM-1035_VIVA_eMP_10.01.11
SecureDecrypt : RM-1035_LANG_PACK_ROM_IJ_eMP_10.01.11_001
SecureDecrypt : RM-1035_CUSTPACK_ROM_IJ_MEA_PK_eMP_10.01.11_001
SecureDecrypt : RM-1035_JUMP_TABLE_IJ_MEA_PK_eMP_10.01.11_001
OVRLP : 000069B900000001
PHPID : CRYSTAL.10.01.11.p2
OVRLP : 00004DF900000001
DA : FORMAT_BIN
Processing Flash Pre-format
FILES : 5
SAFE_BLOCK : 04
FORMAT_BIN : Ok
WRITE_STYLE : DEF : 0x01 (SEQ)
Write : RM-1035_ROM_eMP_10.01.11
Write : RM-1035_LANG_PACK_ROM_IJ_eMP_10.01.11_001
Write : RM-1035_CUSTPACK_ROM_IJ_MEA_PK_eMP_10.01.11_001
Write : RM-1035_JUMP_TABLE_IJ_MEA_PK_eMP_10.01.11_001
Write : RM-1035_VIVA_eMP_10.01.11
CODE_DNLOAD : Ok
[VERIFY] DONE : RM-1035_ROM_eMP_10.01.11
[VERIFY] DONE : RM-1035_LANG_PACK_ROM_IJ_eMP_10.01.11_001
[VERIFY] DONE : RM-1035_CUSTPACK_ROM_IJ_MEA_PK_eMP_10.01.11_001
[VERIFY] DONE : RM-1035_JUMP_TABLE_IJ_MEA_PK_eMP_10.01.11_001
[VERIFY] DONE : RM-1035_VIVA_eMP_10.01.11
CODE_VERIFY : Ok
Executing FFS FORMAT now...
FAT_RANGE : 0x003A4000-0x003F3FFF , LEN : 0x00050000
DA_RET  : DA_IN_PROGRESS
DA_RET  : FORMAT_DONE
Rebooting phone now

Flashing done!
Total flash time : 00:00:52
Reboot phone Ok


RAJAN BHAGORIYA 04-29-2017 07:09

Nokia 225 hang to logo done with nokia best
 
http://i64.tinypic.com/17s8ja.png


All times are GMT +1. The time now is 08:43.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2021 DragonByte Technologies Ltd.
- GSM Hosting Ltd. - 1999-2017 -

Page generated in 0.72673 seconds with 6 queries

SEO by vBSEO