TA-1034 Hang on Logo Flashing error
 

Card found : 0A11858A , v0122
Infinity-Box BEST Nokia [HMD] Module [NK2] v1.08


Open VPLfile : TA-1034_059Z0X6_11.00.11.vpl
Description : TA-1034 IM
DeviceType : TA-1034
ProductCode : 059Z0X6
SoftwareVer : 11.00.11
Load Ok!

Operation : Write FirmWare [ v1.08 ]
Setting : UserData erase : True
Setting : LangPack Only : False

1. Make sure device is powered off. Power off, if need. Wait 10 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : Nokia USB Serial Port (COM124)
MODE : NOKIA USB SERIAL
PORT : 124
BROM : Init BROM
BROM init passed!
CHIP : MT6261 , SBID : 0xCB01 , HWVR : 0x8000 , SWVR : 0x0001
BROM : SECCFG : 0x00000007
BROM : NOKIA USB SERIAL
BROM : 0x05 BL : 0x00
BROM : MEID : C4DA21B4E80F9C58E0A2E3574C7EBF66
BROM : Run BootLoader ...
BROM : BootLoader start Failed! Check device Battery and BSI line!

Error : Fail to init protocol!
Remove battery, cable. Check cable and connection. Repeat operation!

Reconnect Power/Cable!

Operation : Write FirmWare [ v1.08 ]
Setting : UserData erase : True
Setting : LangPack Only : False

1. Make sure device is powered off. Power off, if need. Wait 10 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : Nokia USB Serial Port (COM124)
MODE : NOKIA USB SERIAL
PORT : 124
Error : Failed to open port!

Error : Fail to init protocol!
Remove battery, cable. Check cable and connection. Repeat operation!

Reconnect Power/Cable!

Operation : Write FirmWare [ v1.08 ]
Setting : UserData erase : True
Setting : LangPack Only : False

1. Make sure device is powered off. Power off, if need. Wait 10 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : Nokia USB Serial Port (COM124)
MODE : NOKIA USB SERIAL
PORT : 124
BROM : Init BROM
BROM init passed!
CHIP : MT6261 , SBID : 0xCB01 , HWVR : 0x8000 , SWVR : 0x0001
BROM : SECCFG : 0x00000007
BROM : NOKIA USB SERIAL
BROM : 0x05 BL : 0x00
BROM : MEID : C4DA21B4E80F9C58E0A2E3574C7EBF66
BROM : Run BootLoader ...
BROM : BootLoader start Failed! Check device Battery and BSI line!

Error : Fail to init protocol!
Remove battery, cable. Check cable and connection. Repeat operation!

Reconnect Power/Cable!

Operation : Write FirmWare [ v1.08 ]
Setting : UserData erase : True
Setting : LangPack Only : False

1. Make sure device is powered off. Power off, if need. Wait 10 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : Nokia USB Serial Port (COM124)
MODE : NOKIA USB SERIAL
PORT : 124
BROM : Init BROM
BROM init passed!
CHIP : MT6261 , SBID : 0xCB01 , HWVR : 0x8000 , SWVR : 0x0001
BROM : SECCFG : 0x00000007
BROM : NOKIA USB SERIAL
BROM : 0x05 BL : 0x00
BROM : MEID : C4DA21B4E80F9C58E0A2E3574C7EBF66
BROM : Run BootLoader ...
BROM : BootLoader start Failed! Check device Battery and BSI line!

Error : Fail to init protocol!
Remove battery, cable. Check cable and connection. Repeat operation!

Reconnect Power/Cable!

Does logs not help you understand problem?

Ta-1017
 

I gess this is the problem BROM : BootLoader start Failed! Check device Battery and BSI line! bsi line fault 90%