mt15i dead - GSM-Forum

soyyao · 06-19-2012, 23:32

after unlock with octopus box, not power my phone
i try repair with medusabox, but not flash, not repair

Welcome to Medusa Box Flasher version 1.0.7
--------------------------------------------------------------------------------
Platform: SE Qualcomm
Selected model: MT15i
Prepairing loaders...OK
Please, reconnect battery, attach testpoint and connect USB cable...OK
Please, disconnect testpoint.
Sending loader...OK
Waiting for loader...OK
Reading info...OK
Initializing flash...OK
Flash type : NAND
Flash ID : 5591B398
NAND page size: 2048 b
NAND pages per block: 64 b
NAND spare size: 64 b
NAND blocks count: 8192
Flash size: 1024 MB
Calculating security...OK
Erasing entire flash...OK
Detected bad blocks: 0
Repairing SBL...Failed!

help me please

Medusa Box · 06-20-2012, 05:35

Quote:

Repairing SBL...Failed!

Please try again. If the problem (error) will be the same - most likely there is problem with phone's flash chip.

soyyao · 06-20-2012, 15:03

i try again, same error, phone connect the computer but not run with hold back botton, not flash

some solution.??

livestrong · 06-26-2012, 08:42

in lower version of medusa log...

Welcome to Medusa Box Flasher version 1.0.4
--------------------------------------------------------------------------------
Platform: SE Qualcomm
Selected model: MT11i
Prepairing loaders...OK
Please, reconnect battery, attach testpoint and connect USB cable...OK
Sending loader...OK
Waiting for loader...OK
Reading info...OK
Initializing flash...OK
Calculating security...OK
Erasing entire flash...OK
Detected bad blocks: 0
Repairing SBL...OK
Writing TA...OK
Writing TA_MISC...OK
Phone succesfully repaired.
To complete the operation, please write firmware.

problem the same no power...

in latest version of flasher

Welcome to Medusa Box Flasher version 1.0.7
--------------------------------------------------------------------------------
Platform: SE Qualcomm
Selected model: MT11i
Prepairing loaders...OK
Please, reconnect battery, attach testpoint and connect USB cable...OK
Please, disconnect testpoint.
Sending loader...OK
Waiting for loader...OK
Reading info...OK
Initializing flash...OK
Flash type : NAND
Flash ID : 55D1B32C
NAND page size: 2048 b
NAND pages per block: 64 b
NAND spare size: 64 b
NAND blocks count: 8192
Flash size: 1024 MB
Calculating security...OK
Erasing entire flash...OK
Detected bad blocks: 0
Repairing SBL...Failed!
--------------------------------------------------------------------------------
Platform: SE Qualcomm
Selected model: MT11i
Please, reconnect battery, hold "Vol-" key and connect USB cable...Canceled.
--------------------------------------------------------------------------------
Platform: SE Qualcomm
Selected model: MT11i
Prepairing loaders...OK
Please, reconnect battery, attach testpoint and connect USB cable...OK
Please, disconnect testpoint.
Sending loader...OK
Waiting for loader...OK
Reading info...OK
Initializing flash...OK
Flash type : NAND
Flash ID : 55D1B32C
NAND page size: 2048 b
NAND pages per block: 64 b
NAND spare size: 64 b
NAND blocks count: 8192
Flash size: 1024 MB
Calculating security...OK
Erasing entire flash...Failed!

there is failed...

unit is dead...

hope there is a solution on this???

Medusa Box · 06-26-2012, 08:46

Please try again. If Repair process will be successful, please don't forget to re-flash the phone after of Repair. If the problem will be the same - this can be the problem with phone's flash chip.

06-19-2012, 23:32	#1 (permalink)
soyyao Junior Member Join Date: Mar 2008 Posts: 34 Member: 722925 Status: Offline Thanks Meter: 10	mt15i dead after unlock with octopus box, not power my phone i try repair with medusabox, but not flash, not repair Welcome to Medusa Box Flasher version 1.0.7 -------------------------------------------------------------------------------- Platform: SE Qualcomm Selected model: MT15i Prepairing loaders...OK Please, reconnect battery, attach testpoint and connect USB cable...OK Please, disconnect testpoint. Sending loader...OK Waiting for loader...OK Reading info...OK Initializing flash...OK Flash type : NAND Flash ID : 5591B398 NAND page size: 2048 b NAND pages per block: 64 b NAND spare size: 64 b NAND blocks count: 8192 Flash size: 1024 MB Calculating security...OK Erasing entire flash...OK Detected bad blocks: 0 Repairing SBL...Failed! help me please

06-20-2012, 15:03	#3 (permalink)
soyyao Junior Member Join Date: Mar 2008 Posts: 34 Member: 722925 Status: Offline Thanks Meter: 10	problem same i try again, same error, phone connect the computer but not run with hold back botton, not flash some solution.??

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Repaired dead phone without backup	Prodigal	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	3	07-29-2011 11:26
HELP Dead 5130 v5.00	N.Schmetz	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	4	03-08-2011 04:51
help! Dead 5110 v5.30	aklishin	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	3	04-04-2001 11:56
nokia 5110 dead	alpha	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	0	02-28-2001 11:59
6150 V5.20 WANTED --- DEAD OR ALIVE --- IT'S BETTER ALIVE ! ;)))	tcamilo	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	0	12-19-1999 22:30

06-26-2012, 08:42	#4 (permalink)
livestrong Freak Poster Join Date: May 2007 Location: philippines Posts: 239 Member: 517175 Status: Offline Sonork: none Thanks Meter: 44	in lower version of medusa log... Welcome to Medusa Box Flasher version 1.0.4 -------------------------------------------------------------------------------- Platform: SE Qualcomm Selected model: MT11i Prepairing loaders...OK Please, reconnect battery, attach testpoint and connect USB cable...OK Sending loader...OK Waiting for loader...OK Reading info...OK Initializing flash...OK Calculating security...OK Erasing entire flash...OK Detected bad blocks: 0 Repairing SBL...OK Writing TA...OK Writing TA_MISC...OK Phone succesfully repaired. To complete the operation, please write firmware. problem the same no power... in latest version of flasher Welcome to Medusa Box Flasher version 1.0.7 -------------------------------------------------------------------------------- Platform: SE Qualcomm Selected model: MT11i Prepairing loaders...OK Please, reconnect battery, attach testpoint and connect USB cable...OK Please, disconnect testpoint. Sending loader...OK Waiting for loader...OK Reading info...OK Initializing flash...OK Flash type : NAND Flash ID : 55D1B32C NAND page size: 2048 b NAND pages per block: 64 b NAND spare size: 64 b NAND blocks count: 8192 Flash size: 1024 MB Calculating security...OK Erasing entire flash...OK Detected bad blocks: 0 Repairing SBL...Failed! -------------------------------------------------------------------------------- Platform: SE Qualcomm Selected model: MT11i Please, reconnect battery, hold "Vol-" key and connect USB cable...Canceled. -------------------------------------------------------------------------------- Platform: SE Qualcomm Selected model: MT11i Prepairing loaders...OK Please, reconnect battery, attach testpoint and connect USB cable...OK Please, disconnect testpoint. Sending loader...OK Waiting for loader...OK Reading info...OK Initializing flash...OK Flash type : NAND Flash ID : 55D1B32C NAND page size: 2048 b NAND pages per block: 64 b NAND spare size: 64 b NAND blocks count: 8192 Flash size: 1024 MB Calculating security...OK Erasing entire flash...Failed! there is failed... unit is dead... hope there is a solution on this???

06-26-2012, 08:46	#5 (permalink)
Medusa Box Product Supporter Join Date: Mar 2011 Location: Octopus-team Posts: 9,360 Member: 1538383 Status: Offline Sonork: 100.1587278 Thanks Meter: 3,398	Please try again. If Repair process will be successful, please don't forget to re-flash the phone after of Repair. If the problem will be the same - this can be the problem with phone's flash chip.