|
Welcome to the GSM-Forum forums. You are currently viewing our boards as a guest which gives you limited access to view most discussions and access our other features. Only registered members may post questions, contact other members or search our database of over 8 million posts. Registration is fast, simple and absolutely free so please - Click to REGISTER! If you have any problems with the registration process or your account login, please contact contact us . |
|
Register | FAQ | Donate | Forum Rules | Root any Device | ★iPhone Unlock★ | ★ Direct Codes ★ | Direct Unlock Source | Mark Forums Read |
Easy-Jtag / Easy-Jtag Plus The official support section. You can ask here your question and get answer regarding using Easy-Jtag / Easy-Jtag Plus. |
| LinkBack | Thread Tools | Display Modes |
03-29-2022, 13:45 | #1 (permalink) |
No Life Poster Join Date: Nov 2006 Location: colombo
Posts: 790
Member: 399781 Status: Offline Thanks Meter: 94 | a207f frp error Z3X EasyJtag Software ver. 3.7.0.24 Loading eMMC GEN1 Firmware... IO: 3300 mV Box S/N: 1414110FBFBA99FD, ,FW Ver.: 01.63 Warning: CMD Pullup Level (0 mV) too low , check cables etc.! CMD Active Level:0 mV Box IO Level:3300 mV CLK Rate:14000 kHz Bus Width:1bit,SDR HiPower mode is ON! Can't init device, Reason: CMD Timeout Error Done. i tried many times checking the isp connection but i just get this error message, is this something to do with the adaptor or connection, please help me on this |
03-30-2022, 04:54 | #2 (permalink) |
No Life Poster Join Date: Nov 2006 Location: colombo
Posts: 790
Member: 399781 Status: Offline Thanks Meter: 94 | after trying and getting thst error , phone now not on, its in brick mode,how to unbrick now, the phone is not connecting in easy jtag isp testpoint, and now not on and is in brick mode |
03-30-2022, 05:19 | #4 (permalink) |
Freak Poster Join Date: Aug 2010 Location: Russia,Yekaterinburg
Posts: 102
Member: 1363017 Status: Offline Thanks Meter: 44 | Warning: CMD Pullup Level (0 mV) too low , check cables etc.! CMD Active Level:0 mV 1.you initially did not have power on the chip Soldered vccq and vcc or powered the device from a USB cable? 2.Is the ISP pinout correct? 3.Have you most likely removed the protective screens, not demolished the radio elements at the same time? |
The Following User Says Thank You to andrei_d1978 For This Useful Post: |
03-30-2022, 07:38 | #5 (permalink) |
No Life Poster Join Date: Nov 2006 Location: colombo
Posts: 790
Member: 399781 Status: Offline Thanks Meter: 94 | i am getting this error Z3X EasyJtag Software ver. 3.7.0.24 Loading eMMC GEN1 Firmware... IO: 2800 mV Box S/N: 1414110FBFBA99FD, ,FW Ver.: 01.63 CMD Pullup Level:1691 mV CMD Active Level:2588 mV Box IO Level:2800 mV CLK Rate:14000 kHz Bus Width:1bit,SDR HiPower mode is ON! Can't init device, Reason: CMD Timeout Error Done. |
03-30-2022, 08:31 | #6 (permalink) | |
No Life Poster Join Date: Jan 2010 Location: South africa Age: 35
Posts: 2,672
Member: 1197620 Status: Offline Sonork: 100.1602278 Thanks Meter: 647 | Quote:
share clear photo as i see i think you isp pinouts not right or may be emmc not getting right voltage | |
03-31-2022, 05:55 | #7 (permalink) |
No Life Poster Join Date: Nov 2006 Location: colombo
Posts: 790
Member: 399781 Status: Offline Thanks Meter: 94 | yes it was the testpoint problem, now its done but phone is not on, its in qualcomm 9008 mode, will flashing the bootloader file bring it back to life or is there something to do in hardware side thank you |
03-31-2022, 13:35 | #8 (permalink) |
No Life Poster Join Date: Nov 2006 Location: colombo
Posts: 790
Member: 399781 Status: Offline Thanks Meter: 94 | again i get the same error Z3X EasyJtag Software ver. 3.7.0.20 Loading eMMC GEN1 Firmware... IO: 2800 mV Box S/N: 1414110FBFBA99FD, ,FW Ver.: 01.63 Warning: CMD Pullup Level (0 mV) too low , check cables etc.! CMD Active Level:0 mV Box IO Level:2800 mV CLK Rate:21000 kHz Bus Width:1bit,SDR HiPower mode is ON! Can't init device, Reason: CMD Timeout Error Done. phone is stuck in qualcomm mode, how to exit this mode, phone did connect yesterday after trying so many times and i did android frp clear from anvanced tab, and removed testpoint and checked , the phone was on qualcomm mode, now trying again to revive by flashing bl from same firm version but phone not connecting again where to check and how to bring the phone back to life thank you |
Bookmarks |
Thread Tools | |
Display Modes | |
| |
|