Easy JTAG FRP MOTO G4 XT1640/1643/XT1626 - GSM-Forum

elvisluizs · 08-17-2017, 15:20

FRP ALL PATCH EasyJtag , 1 June 2017

Tutorial:

https://www.youtube.com/watch?v=GKkbRpfAGeA
Pinout!

agrsat · 08-17-2017, 16:28

https://www.youtube.com/watch?v=fySzKpdQHhA

vickyjadhav6161 · 08-24-2017, 20:57

thx, but where is the vcc N Vccq..

umarmsn · 08-25-2017, 05:54

Any one tested ?

.

pass_reply1 · 08-26-2017, 20:42

How is it the procedure?

toninhosantos · 08-27-2017, 03:40

Quote:

Originally Posted by umarmsn

Any one tested ?

.

yes , 1000% tested by myself in two phones.

umarmsn · 08-27-2017, 03:53

Quote:

Originally Posted by toninhosantos

yes , 1000% tested by myself in two phones.

Thanks for tested report

reset12345 · 08-29-2017, 11:45

Quote:

Originally Posted by toninhosantos

yes , 1000% tested by myself in two phones.

Quote:

Originally Posted by umarmsn

Thanks for tested report

Ok Buts its very heard work.......

abdul kadhar · 08-31-2017, 13:40

moto frp ready for moto service center not posible all box and dongle waste my time go to moto service center only 20 minuts ready my mobile...charge only 300rs

toninhosantos · 08-31-2017, 19:33

For vcc and vccq use usb cable.

umarmsn · 09-01-2017, 06:14

Quote:

Originally Posted by toninhosantos

For vcc and vccq use usb cable.

tested done

javier10487 · 09-03-2017, 01:03

alguien tiene el pinout completo?
v3.3?
v1.8?
ya solde los pinouts de data0, gnd, cmd y clk
ayuda!

javier10487 · 09-03-2017, 01:17

Z3X EasyJtag Software ver. 2.5.0.8

Loading eMMC Addon Firmware... IO: 1850 mV
Box S/N: 10FFC008211B940E, ,FW Ver.: 01.58
CMD Pullup Level:1722 mV
CMD Active Level:1804 mV
Box IO Level:1850 mV
CLK Rate:14000 khz
HiPower mode is off!
Can't init device, Reason: CMD Timeout Error
Done.

toninhosantos · 09-03-2017, 01:42

In emmc voltage use 3.3v.

pass_reply1 · 09-03-2017, 20:16

backup dump xt1621??

08-17-2017, 15:20	#1 (permalink)
elvisluizs Junior Member Join Date: Oct 2010 Location: BRASIL Age: 31 Posts: 25 Member: 1417441 Status: Offline Sonork: 354248007787143 Thanks Meter: 42	Easy JTAG FRP MOTO G4 XT1640/1643/XT1626 FRP ALL PATCH EasyJtag , 1 June 2017 Tutorial: https://www.youtube.com/watch?v=GKkbRpfAGeA Pinout!

08-17-2017, 16:28	#2 (permalink)
agrsat Crazy Poster Join Date: Jun 2016 Posts: 56 Member: 2584885 Status: Offline Thanks Meter: 30	https://www.youtube.com/watch?v=fySzKpdQHhA

08-24-2017, 20:57	#3 (permalink)
vickyjadhav6161 No Life Poster Join Date: Apr 2015 Location: Left out from our gsm field Age: 29 Posts: 976 Member: 2386560 Status: Offline Sonork: NOW I DON'T USE IT Thanks Meter: 561	thx, but where is the vcc N Vccq..

08-25-2017, 05:54	#4 (permalink)
umarmsn No Life Poster Join Date: Oct 2007 Location: chennai Age: 38 Posts: 5,480 Member: 616909 Status: Offline Sonork: 1672125 Thanks Meter: 648	Any one tested ? .

08-26-2017, 20:42	#5 (permalink)
pass_reply1 Crazy Poster Join Date: Nov 2013 Location: Argentina Age: 36 Posts: 57 Member: 2058966 Status: Offline Thanks Meter: 12	How is it the procedure?

08-31-2017, 13:40	#9 (permalink)
abdul kadhar Freak Poster Join Date: Dec 2007 Location: trichy Posts: 138 Member: 651994 Status: Offline Sonork: n/a Thanks Meter: 62	moto frp ready for moto service center not posible all box and dongle waste my time go to moto service center only 20 minuts ready my mobile...charge only 300rs

08-31-2017, 19:33	#10 (permalink)
toninhosantos No Life Poster Join Date: Jun 2010 Location: Xique-Xique-Bahia, Brasil Age: 46 Posts: 904 Member: 1320000 Status: Offline Sonork: 100.1667898 Thanks Meter: 272	For vcc and vccq use usb cable.

09-03-2017, 01:03	#12 (permalink)
javier10487 Junior Member Join Date: Sep 2017 Posts: 5 Member: 2753858 Status: Offline Thanks Meter: 1	alguien tiene el pinout completo? v3.3? v1.8? ya solde los pinouts de data0, gnd, cmd y clk ayuda!

09-03-2017, 01:17	#13 (permalink)
javier10487 Junior Member Join Date: Sep 2017 Posts: 5 Member: 2753858 Status: Offline Thanks Meter: 1	Z3X EasyJtag Software ver. 2.5.0.8 Loading eMMC Addon Firmware... IO: 1850 mV Box S/N: 10FFC008211B940E, ,FW Ver.: 01.58 CMD Pullup Level:1722 mV CMD Active Level:1804 mV Box IO Level:1850 mV CLK Rate:14000 khz HiPower mode is off! Can't init device, Reason: CMD Timeout Error Done.

09-03-2017, 01:42	#14 (permalink)
toninhosantos No Life Poster Join Date: Jun 2010 Location: Xique-Xique-Bahia, Brasil Age: 46 Posts: 904 Member: 1320000 Status: Offline Sonork: 100.1667898 Thanks Meter: 272	In emmc voltage use 3.3v.

09-03-2017, 20:16	#15 (permalink)
pass_reply1 Crazy Poster Join Date: Nov 2013 Location: Argentina Age: 36 Posts: 57 Member: 2058966 Status: Offline Thanks Meter: 12	backup dump xt1621??