EasyJTAG v.2.1 Released. New phones added and lot of changes.

[NoName®]

Easy JTAG Software v.2.1 Release Notes:




We working hard last 3 years to make EasyJTAG are best solution on market.
We have greatly increased read and write operation speed , using a protocol compression.
In fact most dumps have areas with big amounts of repeating data. So what we get:

Test Config #1 Intel Core I5/8Gb , Windows 7 x64 eMMC Toshiba MMC16G
Write on FW1.52 976KB/S FW1.54 1449KB/S (48% speed increase)
Read on FW.52 788KB/S FW1.54 1457KB/S (84% speed increase)

Test Config #2 Intel Core 2Duo/2Gb , Windows XP x32 eMMC Toshiba MMC16G
Write on FW1.52 741KB/S FW1.54 1102KB/S (48% speed increase)
Read on FW1.52 606KB/S FW1.54 1074KB/S (77% speed increase)


Software changes:
- Added ability to configure eMMC bus frequency ( 1MHz,3MHz,7MHz,14MHz,21MHz)
- Fixed new Gemalto IDCore 10 security cards loss bugs. Link: http://forum.gsmhosting.com/vbb/f672...oblem-2083031/
- Improved software startup time.
- Improved eMMC operations speed.
- Fixed crash after updating box firmware.


Box Firmware 1.54 changes:
- Added eMMC read / write compression ( upto 1.4MB/s on typical eMMC data)
- Increased maximum clock rate for eMMC - 21MHz
- Improved box stability issues.
- Fixed SmartCard Detection Delay for Windows 7



New phones added via DIRECT EMMC(ISP) connection :
- support LG D295 (ISP Pinout, Dumps)
- support SAMSUNG SM-G130M (ISP Pinout, Dumps)
- support SAMSUNG SM-A500 (ISP Pinout, Dumps)
- support SAMSUNG GT-S7560M (ISP Pinout, Dumps)
- support SAMSUNG GT-S6790L(ISP Pinout, Dumps)
- support HUAWEI G510 (ISP Pinout, Dumps)
- support AMAZON KINDLE FIRE HD X43Z60 (ISP Pinout, Dumps)
- support SONY C2104 (ISP Pinout, Dumps)
- support SONY M2 (ISP Pinout, Dumps)
- support SONY C2005 (ISP Pinout)


Thanks all testers for great work!
Special thank to Seba Kopp and GsmServer crew for IDCore Samples!
For avoiding problems with X64 and drivers - use test signing mode

Copy'n'Pasters Seafood team - your next move ;-)

[ali1371]

great

we hope you release mtk scatter flasher in next update

[vikboston]

Originally Posted by ali1371

great

we hope you release mtk scatter flasher in next update

Yes, we do!
Best Regards

[ali1371]

Processing file...I:\Emmc dumps\HTC ONE SV PL80150\EMMC_ROM1_H8G2d_8272985_00000000_08000000. bin
Z3X EasyJtag Software ver. 2.1.0.0
Skip loading eMMC Addon Firmware
CMD Pullup Level:1144 mV
CMD Active Level:1567 mV
Input file : I:\Emmc dumps\HTC ONE SV PL80150\EMMC_ROM1_H8G2d_8272985_00000000_08000000. bin
Writing 0008000000 bytes to 00000000 ...ROM1 (USER ROM)
Done. Write Speed: 30510 kB/s

thnx easy-jtag team

[saleem5001]

Wao we r waiting next for mtk same xxxfi box

[anasshe]

can i use c2104 dump to revive c2105?

[shamsulhaq]

add dead reloader flasher direct emmc or usb port

[gsm_enggine]

after update i can't detec any EMMC ic

Loading eMMC Addon Firmware... IO: 2800 mV
Box S/N: xxxxxxxx, ,FW Ver.: 01.54
CMD Pullup Level:2753 mV
CMD Active Level:2825 mV
Box IO Level:2800 mV
CLK Rate:14000 khz
HiPower™ mode is off!
Can't init device, Reason: DATA Status Error [Box Internal Failure]
Done.

update box firmware work normaly until finish

help me please


thx

[vikboston]

Hi,
Try to install software 2.0.8.5 and check eMMC connection with fw 1.54 and sw 2.0.8.5.
If same problem occurs, start software 2.0.8.5 and hold CTRL (firmware downgrade starts automatically), then start sw again and check eMMC connection with fw 1.52 and sw 2.0.8.5.
Recently problem 'DATA Status Error [Box Internal Failure]' happened, when box has internal soldering problems!
Box fw 1.54 is compatible to fw 1.52 and typically can't cause this problem. We didn't touch any feature in fw 1.54 that can make problem like this.
If you fully disconnect eMMC Socket/ISP Adapter from box, and after detect have error 'DATA Status Error [Box Internal Failure]', its most possible box internal factory soldering problems.
If 'DATA Status Error [Box Internal Failure]' happened with connected eMMC, try to disable 'Hi Power CLK drive mode' option (if enabled) and select box IO level to 3.3V.
ISP connection works much better with pull-up resisors 100 ohm between CMD and 1.8V, between DAT0 and 1.8V.
Report results for me.
Best Regards

[Mehdi Ghorbani]

also i have problem with new version of easy-jtag box(2.1.0.0)

extCSD file...C:\Mac Mobile\Samsung\Flash File\J700h\400073_1551747119_20160506_0242.extcsd
Running:Repair extCSD...
Z3X EasyJtag Software ver. 2.1.0.0
Skip loading eMMC Addon Firmware
CMD Pullup Level:453 mV
CMD Active Level:2062 mV
Box IO Level:3300 mV
CLK Rate:3000 khz
Can't init device, Reason: DATA Status Error [Box Internal Failure]
Done.

[vikboston]

Originally Posted by Mehdi Ghorbani

everything is ok before upgrade master..

Ok,
If possible, write me in PM Team Viwer id/ pass.
I can try to figure out this problem.
Thank You

[Mehdi Ghorbani]

Hi again ....Thanks master for your help ..
problem solved with disable Hipower CLK Drive Mode!
BR.

[elpring]

what about mtk android phones and sony mtk phones

[aa39]

add mtk scatter flasher on emmc mode

[vikboston]

Originally Posted by aa39

add mtk scatter flasher on emmc mode

Hi
MTK scatter is ready and will be available in next update!
Best Regards