G532M dead boot not repaired (EMMC QE63MB)

[movilexpert]

Hello Team
i have G532m dead by downgrade
and i connected isp and write by vendor full combination file, flashing ok but dead, i wrote rom1,rom2,rom3 files dump from support and nothing.
EMMC is QE63MB, not QN16BB same other i repaired

Setting interface to EasyJtag2/ISP
Setting bus width to 1 Bit
Setting frequence to 24 MHz
CMD Pullup Level: 1804 mV
CMD Active Level: 1865 mV
EMMC Device Information :
EMMC CID: 150100514536334D4200668CE42DA531
EMMC CSD: D02701320F5903FFF6DBFFEF8E40400D
EMMC Manufacture : SAMSUNG , EMMC NAME: QE63MB , HEX: 514536334D42 , S/N: 668CE42D , rev. 0x00
EMMC Manufacture ID: 0x15 , OEM ID: 0x00 , Device Type: BGA (Discrete embedded) , Date: 10/2018
EMMC ROM 1 (Main User Data) Capacity: 15028 MB (0003AB400000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 16384 KB (000001000000) Counter: 0 , Response: Maybe not clean
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.8 (MMC 5.1)
Boot configuration [PARTITION_CONFIG]: 0x48 , Boot from: ROM2 (Boot partition 1)
Boot Bus Config: 0x00 , width 1bit
H/W Reset Function [RST_N_FUNCTION]: 0x01, RST_n signal is permanently enabled
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: QE63MB_668CE42D_20200126_054747.extcsd
EMMC Init completed.

Get firmware version

Brand = samsung
Manufacturer = samsung
Device = grandpplte
Model = SM-G532M
Phone platform = mt6737t
CPU Abi = armeabi-v7a
Mediatek platform = MT6737T
Android release = 6.0.1
Firmware version = MMB29T.FA60_G532MUBU1AQL1
Firmware date = Fri Dec 1 14:01:49 KST 2017

[ilyasrao]

MANUALLY ERASE ROM2 , ROM3 , AND ROM1
THAN WRITE https://mega.nz/#!AKJBkIwT!VW6IpGwd7...dAjo8j43tjmUNA

[duboy]

Originally Posted by ilyasrao

MANUALLY ERASE ROM2 , ROM3 , AND ROM1
THAN WRITE https://mega.nz/#!AKJBkIwT!VW6IpGwd7...dAjo8j43tjmUNA

sr this link not work help i have same problems
Setting interface to EasyJtag2/ISP
Setting bus width to 1 Bit
Setting frequence to 12 MHz
CMD Pullup Level: 1885 mV
CMD Active Level: 2235 mV
EMMC Device Information :
EMMC CID: 150100514536334D42003632CE7BB55B
EMMC CSD: D02701320F5903FFF6DBFFEF8E40400D
EMMC Manufacture : SAMSUNG , EMMC NAME: QE63MB , HEX: 514536334D42 , S/N: 3632CE7B , rev. 0x00
EMMC Manufacture ID: 0x15 , OEM ID: 0x00 , Device Type: BGA (Discrete embedded) , Date: 11/2018
EMMC ROM 1 (Main User Data) Capacity: 15028 MB (0003AB400000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 16384 KB (000001000000) Counter: 0 , Response: Maybe not clean
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.8 (MMC 5.1)
Boot configuration [PARTITION_CONFIG]: 0x48 , Boot from: ROM2 (Boot partition 1)
Boot Bus Config: 0x00 , width 1bit
H/W Reset Function [RST_N_FUNCTION]: 0x01, RST_n signal is permanently enabled
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: QE63MB_3632CE7B_20220118_175036.extcsd
EMMC Init completed.

[whisarmon]

If the phone was 16gb and died from downgrade, you just had to rewrite pit and BL.