GSM-Forum - [GUIDE] How to find DIRECT EMMC PINOUT. Step by step with pictures.

GSM-Forum (https://forum.gsmhosting.com/vbb/)

- Easy-Jtag / Easy-Jtag Plus (https://forum.gsmhosting.com/vbb/f672/)

- - [GUIDE] How to find DIRECT EMMC PINOUT. Step by step with pictures. (https://forum.gsmhosting.com/vbb/f672/guide-how-find-direct-emmc-pinout-step-step-pictures-1724774/)

[GUIDE] How to find DIRECT EMMC PINOUT. Step by step with pictures.

How to find DIRECT EMMC PINOUT.

Attention! This way is not safe for working pcb.

For pinout find need:

Quote:

1. Need Multimeter.
2. Need PCB with emmc.
3. Sodering stationg.

Now steps.:
1. Here pcb. for example we take GT-I9500 board.

http://imageshack.us/a/img199/1019/s76.JPG

2. Multimeter.

[IMG]http://4.bp.********.com/-GbDO8OqTJ8Y/UEyboG-xbUI/AAAAAAAAChY/HmedxGWOWbo/s1600/Multimeter.jpg[/IMG]

3. Here pcb with removed EMMC.

http://imageshack.com/a/img20/1432/ms6j.jpg

4. Here pcb with market pins. Check position point before start job.

http://imageshack.us/a/img29/705/0vll.jpg

5. Here default pinout of BGA169 emmc with position point and pinout.

http://imageshack.com/a/img818/9664/57fj.jpg

6. Now using tester need test where go pins.

http://imageshack.us/a/img59/5724/7v19.jpg

LETS GO. Now you can connect to emmc.
Check this FAQ - How connect EMMC DIRECT!!!!

Lets collect in this thread tested emmc pinouts.

Other type of EMMC:
http://imageshack.com/a/img842/8197/0iad.jpg

JTAG Z3X gentlemen, you would be so kind to add pinotu of each of the models performed this fantastic box repair EMMC

please thanks

Please pinout
JTAG Z3X gentlemen, you would be so kind to add pinotu of each of the models performed this fantastic box repair EMMC

please thanks

give us the pin out diagrams with latest update thanks,,,.....d master,great team Z3X

can u share i 9300 s3 and n7100 not2 pls

i9100 emmc pinout not tested yet.

Mr. Blang from where can I got the files Main and boot for repair emmc? I need for S2 i9100, i8190, N7000, thx

Samsung Note 2 N7100 EMMC Pinouts

I am trying to read the eMMC chip on a LG MS770 phone that is in working order. The eMMC chip is a Toshiba THGBM4GGD2HBAIC 4GB chip. I traced back Vcc, Clk, Cmd, VccQ, and D0. However when I attempt to read the eMMC chip I get the following error:

EasyJtag Suite ver.: 1.0.88.0 started.
Operating system ver.: Windows 7 (build 7601, Service Pack 1), 64-bit edition.
Successefuly connected to box on COM39
Box S/N: 16XXXX, ,FW Ver.: 01.47
Box Working Mode: JTAG Box.
Box Drivers version: 3.0.0.0, are OK
Z3X Card Serial : AA81-7A1C , ver: 22
Successefuly connected to box on COM39
Box S/N: 16XXXX, ,FW Ver.: 01.47
Loading eMMC Addon Firmware...
CMD Pullup Level:1660 mV
CMD Active Level:2155 mV
eMMC ACK Error ( Check Connection )
eMMC Card initialisation error!

I have rechecked my connections and reconfirmed my connection points on my test phone. See attached image for solder connections.

Any suggestions?

J2

how to fing pinouts in this pcb

how to find pinouts in this pcb

http://i40.tinypic.com/29lz2h1.jpg

MS770 eMMC Pinout

Mr. Blang,
Feel free to add this pinout image to the Easy-JTAG LG MS-770 support files. Using the attached eMMC pinout, I was able to dump the Toshiba memory chip. I have included the log from Easy-JTAG to confirm the connection:

Successefuly connected to box on COM39
Box S/N: 16XXX, ,FW Ver.: 01.47
Loading eMMC Addon Firmware...
CMD Pullup Level:1949 mV
CMD Active Level:2320 mV
EMMC CID 11010030303847344200C794CBC68F6D
EMMC CSD D00E00320F5903FFFFFFFFE79640001F
EMMC Manufactorer ID: 11
EMMC OEM ID: 0100
EMMC Date: 08/2012 FW rev.0x0 HW rev.0x0
EMMC Serial #: 3348417478
EMMC NAME: 008G4B
EMMC Capacity: 7456 MB (High Density Card)
=============================================
Extended CSD rev 1.5 (MMC 4.41)
=============================================
Card Supported Command sets [S_CMD_SET: 0x00]
- Standard MMC command sets
HPI Features [HPI_FEATURE: 0x01]:
implementation based on CMD13
Background operations support [BKOPS_SUPPORT: 0x01]
Background operations status [BKOPS_STATUS: 0x00]
TRIM Multiplier [TRIM_MULT: 0x04]
Secure Feature support [SEC_FEATURE_SUPPORT: 0x15]
Secure Erase Multiplier [SEC_ERASE_MULT: 0x10]
Secure TRIM Multiplier [SEC_TRIM_MULT: 0x42]
Boot Information [BOOT_INFO: 0x07]
Device supports alternative boot method
Device supports dual data rate during boot
Device supports high speed timing during boot
Boot partition size [BOOT_SIZE_MULTI: 0x10]
Access size [ACC_SIZE: 0x07]
High-capacity erase unit size [HC_ERASE_GRP_SIZE: 0x08]
High-capacity erase timeout [ERASE_TIMEOUT_MULT: 0x02]
Reliable write sector count [REL_WR_SEC_C: 0x10]
High-capacity W protect group size [HC_WP_GRP_SIZE: 0x01]
Sleep current (VCC) [S_C_VCC: 0x07]
Sleep current (VCCQ) [S_C_VCCQ: 0x09]
Sleep/awake timeout [S_A_TIMEOUT: 0x11]
Sector Count [SEC_COUNT: 0x00e90000]
Partition switching timing [PARTITION_SWITCH_TIME: 0x01]
Out-of-interrupt busy timing [OUT_OF_INTERRUPT_TIME: 0x05]
Card Type [CARD_TYPE: 0x07]
CSD structure version [CSD_STRUCTURE: 0x02]
Command set [CMD_SET: 0x00]
Command set revision [CMD_SET_REV: 0x00]
Power class [POWER_CLASS: 0x00]
High-speed interface timing [HS_TIMING: 0x00]
Erased memory content [ERASED_MEM_CONT: 0x01]
Boot configuration bytes [PARTITION_CONFIG: 0x00]
Not boot enable
No access to boot partition
Boot config protection [BOOT_CONFIG_PROT: 0x00]
Boot bus Conditions [BOOT_BUS_CONDITIONS: 0x00]
High-density erase group definition [ERASE_GROUP_DEF: 0x00]
=============================================
Boot write protection status registers [BOOT_WP_STATUS]: 0x00
Boot Area Write protection [BOOT_WP]: 0x00
Power ReadOnly locking: possible
Permanent ReadOnly locking: possible
Read Only lock status: not locked
=============================================
User area write protection register [USER_WP]: 0x00
FW configuration [FW_CONFIG]: 0x00
RPMB Size [RPMB_SIZE_MULT]: 0x02
Write reliability setting register [WR_REL_SET]: 0x00
Write reliability parameter register [WR_REL_PARAM]: 0x05
Enable background operations handshake [BKOPS_EN]: 0x00
H/W reset function [RST_N_FUNCTION]: 0x00
HPI management [HPI_MGMT]: 0x00
Partitioning Support [PARTITIONING_SUPPORT]: 0x03
Device support partitioning feature
Device can have enhanced tech.
Max Enhanced Area Size [MAX_ENH_SIZE_MULT]: 0x0003b4
Partitions attribute [PARTITIONS_ATTRIBUTE]: 0x00
Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00
General Purpose Partition Size
[GP_SIZE_MULT_4]: 0x000000
[GP_SIZE_MULT_3]: 0x000000
[GP_SIZE_MULT_2]: 0x000000
[GP_SIZE_MULT_1]: 0x000000
Enhanced User Data Area Size [ENH_SIZE_MULT]: 0x000000
Enhanced User Data Start Address [ENH_START_ADDR]: 0x000000
Bad Block Management mode [SEC_BAD_BLK_MGMNT]: 0x00

I think the main problem is to find out the datasheet of the used eMMC in a particular mobile. Is there anywhere an eMMC datasheet of eMMC chips where i can see which eMMC pin is
VCC,VCCQ,D0,CLK ... .?

I Need Pinout Emmc S2 HD SHV-E120L Plz Help Me , Thanks Mr Blang !!!

Mr blang. I am representing for all of us in the USA. please give more support for English in the United States and more pictures of pin outs. I need the pin out for the direct eMMC connection for a GS III L710

image not found , please upload it again

Well done. I have added this pinout to support database. Left only working dump;-)

Quote:

Originally Posted by Jacques2 (Post 9955880)

Shw-m240s emmc pinout
any body help me................................

Quote:

Originally Posted by ..::akkas_sarkar::.. (Post 10390371)

Shw-m240s emmc pinout
any body help me................................

read manual and follow manual.
i not understand how your post related to thread name?!:confused::confused:

how did you removed mmc ic so perfectly cause when we try we always mess up tracks.
and how did you removed glue from ic.

Is bga153 pinout scheme standard for every eMMC with 153 pins?

good ida.. friends i want i9082 emmc direct pinout

thanks

Help,, I need samsung p7300 direct emmc pinout plissss

I need i9152 emmc pinout????

Is there any solution for Huawei Ascend Y330-U05?

Hello sir pls share the pinout of samsung sIII mini tnx

Need Pinout S6 EDGE SM-G925t

hi
I use this method 100% working
but I've some problems with phones that have MTK Cpu. the problem is I can't find the CLK pin!! I try many time and cant find the CLK point !!!
wath does it mean????

On MTK phones clk is directly under the processor chip.

Quote:

Originally Posted by cinik79 (Post 11662950)

On MTK phones clk is directly under the processor chip.

Please explain how to find out more

فرستاده شده از GT-I9300ِ من با Tapatalk

hjhj please pinout emmc samsung s7392

sir i can i use sboot.bin from samsung stock rom?

same question..how to find it

Quote:

Originally Posted by cinik79 (Post 11662950)

On MTK phones clk is directly under the processor chip.

please help me i want sony c4 e5333 eMMC Direct pinout please

thanks sir.... very good guide

isp need experia sony c5333 .
help meeer ...

connection procedure is OK but where will it joint ? adapter or direct box ?

pls help me

I get box from 1 month back but I don't know to use process

dead boot process I know
but emmc I don't know after connect tp what will I do next

pls help me to use box

lg e420 jtag pinout plz........?
z3x easy jtag box show e400 pcb pinout for e420 . i want e420 pcb pinout for jtaging
plz any boddy have this modle jtag pinout? share image

Quote:

Originally Posted by blang (Post 9791295)

How to find DIRECT EMMC PINOUT.

Attention! This way is not safe for working pcb.

For pinout find need:

Now steps.:
1. Here pcb. for example we take GT-I9500 board.

http://imageshack.us/a/img199/1019/s76.JPG

2. Multimeter.

[IMG]http://4.bp.********.com/-GbDO8OqTJ8Y/UEyboG-xbUI/AAAAAAAAChY/HmedxGWOWbo/s1600/Multimeter.jpg[/IMG]

3. Here pcb with removed EMMC.

http://imageshack.com/a/img20/1432/ms6j.jpg

4. Here pcb with market pins. Check position point before start job.

http://imageshack.us/a/img29/705/0vll.jpg

5. Here default pinout of BGA169 emmc with position point and pinout.

http://imageshack.com/a/img818/9664/57fj.jpg

6. Now using tester need test where go pins.

http://imageshack.us/a/img59/5724/7v19.jpg

LETS GO. Now you can connect to emmc.
Check this FAQ - How connect EMMC DIRECT!!!!

Lets collect in this thread tested emmc pinouts.

Other type of EMMC:
http://imageshack.com/a/img842/8197/0iad.jpg

lg e420 jtag pinout plz. easy jtag box showing e400 pcb diagram pinout. i think e400 and e420 pcb diagram diferant plz help........ iam new to esay jtag box:confused::confused::confused:

good bro............................................... .

share pinout for j700h

i need pinout for this model

Someone can show where to connect the JTAG pins to EMMC
2.8 at EMMC connected to? In Z3X EASY JTAG
1.8 at EMMC connected to? In Z3X EASY JTAG
DAT 0 at EMMC connected to? In Z3X EASY JTAG
thank's in advance

link not working pls repost

sir i need emmc pinout samsung sm-g361h thanx

hi. please upload again....

i need pinout for lenovo A1000 isp
thanks in advance