OPPO K1 Password Reset Done without Data Loss !!EasyJTAG - GSM-Forum

AniAxn · 11-20-2019, 10:33

OPPO K1 Password Reset Done without Data Loss !!EasyJTAG

Wbr,
AniAXN

.:B-A-G:. · 09-29-2022, 18:22

can you share pinout plz

.:B-A-G:. · 09-29-2022, 18:39

i have this error
Can't init device, Reason: CMD Timeout Error
i used with usb cable without vccq vcc

.:B-A-G:. · 09-29-2022, 18:59

and same error with vccq vcc
Z3X EasyJtag Software ver. 3.7.0.24
Loading eMMC GEN1 Firmware... IO: 2800 mV
Box S/N: 04040B05853D1B89, ,FW Ver.: 01.63
Warning: CMD Pullup Level (278 mV) too low , check cables etc.!
CMD Active Level:1557 mV
Box IO Level:2800 mV
CLK Rate:21000 kHz
Bus Width:1bit,SDR
HiPower mode is off!
Can't init device, Reason: CMD Timeout Error

.:B-A-G:. · 09-30-2022, 15:43

any help with this model !!
testpoint is good but always error in cmd

AniAxn · 11-27-2022, 19:28

hello,
simple voltage issue
do puss proper voltage vcc & vccq
also connect strong gnd
wbr
aniaxn

tanvir sekh · 12-01-2022, 15:31

unlock of but mobile restart after hang or logo

11-20-2019, 10:33	#1 (permalink)
AniAxn Product Supporter Join Date: Jun 2009 Location: eMMC & UFS Posts: 4,600 Member: 1045758 Status: Offline Sonork: 100.1613661(Offline) Thanks Meter: 4,307	OPPO K1 Password Reset Done without Data Loss !!EasyJTAG OPPO K1 Password Reset Done without Data Loss !!EasyJTAG Wbr, AniAXN

09-29-2022, 18:39	#3 (permalink)
.:B-A-G:. No Life Poster Join Date: Mar 2010 Location: djerba Posts: 690 Member: 1269161 Status: Offline Thanks Meter: 119	i have this error Can't init device, Reason: CMD Timeout Error i used with usb cable without vccq vcc Last edited by .:B-A-G:.; 09-29-2022 at 18:47.

09-29-2022, 18:22	#2 (permalink)
.:B-A-G:. No Life Poster Join Date: Mar 2010 Location: djerba Posts: 690 Member: 1269161 Status: Offline Thanks Meter: 119	can you share pinout plz

09-29-2022, 18:59	#4 (permalink)
.:B-A-G:. No Life Poster Join Date: Mar 2010 Location: djerba Posts: 690 Member: 1269161 Status: Offline Thanks Meter: 119	and same error with vccq vcc Z3X EasyJtag Software ver. 3.7.0.24 Loading eMMC GEN1 Firmware... IO: 2800 mV Box S/N: 04040B05853D1B89, ,FW Ver.: 01.63 Warning: CMD Pullup Level (278 mV) too low , check cables etc.! CMD Active Level:1557 mV Box IO Level:2800 mV CLK Rate:21000 kHz Bus Width:1bit,SDR HiPower mode is off! Can't init device, Reason: CMD Timeout Error

09-30-2022, 15:43	#5 (permalink)
.:B-A-G:. No Life Poster Join Date: Mar 2010 Location: djerba Posts: 690 Member: 1269161 Status: Offline Thanks Meter: 119	any help with this model !! testpoint is good but always error in cmd

11-27-2022, 19:28	#6 (permalink)
AniAxn Product Supporter Join Date: Jun 2009 Location: eMMC & UFS Posts: 4,600 Member: 1045758 Status: Offline Sonork: 100.1613661(Offline) Thanks Meter: 4,307	hello, simple voltage issue do puss proper voltage vcc & vccq also connect strong gnd wbr aniaxn

12-01-2022, 15:31	#7 (permalink)
tanvir sekh Junior Member Join Date: Jun 2015 Location: rajmahal Posts: 6 Member: 2402680 Status: Offline Thanks Meter: 3	unlock of but mobile restart after hang or logo