HW_PART error. Reason: eMMC >= 4.4 required for enhanced user data area
 

I get following error on creating gp partition , please let me know if theres a way to fix this this . TY



1/9/2021 1:47:31 PM> Looking for EasyJTAG box...
1/9/2021 1:47:31 PM> EasyJTAG API ver. 3401
1/9/2021 1:47:31 PM> Setting IO Levels to 1.8V
1/9/2021 1:47:31 PM> Setting frequence to 36 MHz
1/9/2021 1:47:31 PM> EasyJTAG Box Serial = FB2B3F6110A543ED
1/9/2021 1:47:31 PM> EasyJTAG Box Firmware = 2.5301
1/9/2021 1:47:32 PM> Setting interface to EasyJtag2/ISP_HiPower
1/9/2021 1:47:32 PM> Setting bus width to 1 Bit
1/9/2021 1:47:32 PM> HiPower mode is ON
1/9/2021 1:47:32 PM> Setting frequence to 36 MHz
1/9/2021 1:47:32 PM> CMD Pullup Level: 1816 mV
1/9/2021 1:47:32 PM> CMD Active Level: 1868 mV
1/9/2021 1:47:32 PM> eMMC Init returned = -105
1/9/2021 1:47:32 PM> EMMC Device Information :
1/9/2021 1:47:32 PM> EMMC CID: 13014E53304A3942371004F82F08759D
1/9/2021 1:47:32 PM> EMMC CSD: D05F01328F5913FFFFFFFFEF964000A9
1/9/2021 1:47:32 PM> EMMC Manufacture : MICRON , EMMC NAME: S0J9B7 , HEX: 53304A394237 , S/N: 04F82F08 , rev. 0x10
1/9/2021 1:47:32 PM> EMMC Manufacture ID: 0x13 , OEM ID: 0x4E , Device Type: BGA (Discrete embedded) , Date: 7/2018
1/9/2021 1:47:32 PM> EMMC ROM 1 (Main User Data) Capacity: 29820 MB (000747C00000)
1/9/2021 1:47:32 PM> EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
1/9/2021 1:47:33 PM> EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000) Counter: 41170 , Response: Not Clean
1/9/2021 1:47:33 PM> EMMC Permanent Write Protection: No
1/9/2021 1:47:33 PM> EMMC Temporary Write Protection: No
1/9/2021 1:47:33 PM> Extended CSD Information :
1/9/2021 1:47:33 PM> Extended CSD rev: 1.8 (MMC 5.1)
1/9/2021 1:47:33 PM> Boot configuration [PARTITION_CONFIG]: 0x38 , Boot from: ROM1 (Main User Area)
1/9/2021 1:47:33 PM> Boot Bus Config: 0x00 , width 1bit
1/9/2021 1:47:33 PM> H/W Reset Function [RST_N_FUNCTION]: 0x01, RST_n signal is permanently enabled
1/9/2021 1:47:33 PM> Supported partition features [PARTITIONING_SUPPORT]: 0x07
1/9/2021 1:47:33 PM> Device supports partitioning features
1/9/2021 1:47:33 PM> Device can have enhanced technological features in partitions and user data area
1/9/2021 1:47:33 PM> Device can have extended partitions attribute
1/9/2021 1:47:33 PM> Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
1/9/2021 1:47:33 PM> Backup saved: S0J9B7_04F82F08_20210109_134733.extcsd
1/9/2021 1:47:33 PM> EMMC Init completed.
1/9/2021 1:47:33 PM>
1/9/2021 1:48:06 PM> Warning: Health report is very BAD
1/9/2021 1:48:06 PM>
1/9/2021 1:48:06 PM> Device Life Time Estimation (MLC) [269]: 0x03 20% - 30% device life time used
1/9/2021 1:48:06 PM> Device Life Time Estimation (SLC) [268]: 0x0B Exceeded its maximum estimated device life time
1/9/2021 1:48:06 PM> Pre EOL information [267]: 0x01 Normal
1/9/2021 1:48:06 PM>
1/9/2021 1:48:06 PM> Operation: Changing GP sizes (final write) ...
1/9/2021 1:48:06 PM>
1/9/2021 1:48:06 PM> GP1 size: 0 MB , WR_REL: 1 , ENH 0
1/9/2021 1:48:06 PM> GP2 size: 0 MB , WR_REL: 1 , ENH 0
1/9/2021 1:48:06 PM> GP3 size: 0 MB , WR_REL: 1 , ENH 0
1/9/2021 1:48:06 PM> GP4 size: 0 MB , WR_REL: 1 , ENH 0
1/9/2021 1:48:06 PM>
1/9/2021 1:48:06 PM> Zero sizes. This may damage your eMMC
1/9/2021 1:48:06 PM> Do you want to continue?
1/9/2021 1:48:06 PM>
1/9/2021 1:48:11 PM> HW_PART error. Reason: eMMC >= 4.4 required for enhanced user data area
1/9/2021 1:48:11 PM>

try unset enhanced attribute

how to set enhanced attributes mastes could you please give a small explanation if possible ty .

how set checkbox at software? simply

just unthik all partion bar and finali write then ok