i9300 NO PRODUCT (S3) - successfully repair with easy jtag - GSM-Forum

cangsm · 02-14-2014, 20:53

Loading eMMC Addon Firmware...
Warning: CMD Pullup Level (1196 mV) too low , check cables etc.!!!
CMD Active Level:1650 mV
EMMC CID 15010056545530304DF1985402D47FD7
EMMC CSD D02701320F5903FFF6DBFFFF8E40406D
EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 07/2012 FW rev.0xf1
EMMC NAME: VTU00M , S/N: 2555642580
EMMC ROM1 (Main User Data) Capacity: 15028 MB (High Density Card)
EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB
EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
Extended CSD rev 1.6 (MMC 4.5)
Boot configuration [PARTITION_CONFIG: 0x48] Boot from:ROM2 (Boot Partition 1)
Boot bus config [177]: 0x01 , width 4bits , Partition config [179]: 0x48.
Backup saved: VTU00M_2555642580_20140105_2045.extcsd
Done.
Running:SAMSUNG: Smart Factory Reset + Format...

Successfully connected to box on COM58
Box S/N: 0D01100B3AC50D82, ,FW Ver.: 01.48
Loading eMMC Addon Firmware...
Warning: CMD Pullup Level (1185 mV) too low , check cables etc.!!!
CMD Active Level:1639 mV
EMMC CID 15010056545530304DF1985402D47FD7
EMMC CSD D02701320F5903FFF6DBFFFF8E40406D
EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 07/2012 FW rev.0xf1
EMMC NAME: VTU00M , S/N: 2555642580
EMMC ROM1 (Main User Data) Capacity: 15028 MB (High Density Card)
EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB
EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
Extended CSD rev 1.6 (MMC 4.5)
Boot configuration [PARTITION_CONFIG: 0x48] Boot from:ROM2 (Boot Partition 1)
Boot bus config [177]: 0x01 , width 4bits , Partition config [179]: 0x48.
Backup saved: VTU00M_2555642580_20140105_2047.extcsd
Sending Smart Wipe Request...
Wiping Card... Please do not touch it!!!
Done.
Please don't forget to repair extCSD from backup!!!
Running:SAMSUNG: MoviNAND Format...

Successfully connected to box on COM58
Box S/N: 0D01100B3AC50D82, ,FW Ver.: 01.48
Loading eMMC Addon Firmware...
CMD Pullup Level:1206 mV
CMD Active Level:1639 mV
EMMC CID 15010056545530304DF1985402D47FD7
EMMC CSD D02701320F5903FFF6DBFFFF8E40406D
EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 07/2012 FW rev.0xf1
EMMC NAME: VTU00M , S/N: 2555642580
EMMC ROM1 (Main User Data) Capacity: 15028 MB (High Density Card)
EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB
EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
Extended CSD rev 1.6 (MMC 4.5)
Boot configuration [PARTITION_CONFIG: 0x48] Boot from:ROM2 (Boot Partition 1)
Boot bus config [177]: 0x01 , width 4bits , Partition config [179]: 0x48.
Backup saved: VTU00M_2555642580_20140105_2047.extcsd
Sending Internal Reconfiguration Request...
Waiting configuration Apply!!!
Restoring configuration...
EMMC ROM2/3 (Boot Partitions) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
Wiping Card... Please do not touch it!!!
Done.
Please don't forget to repair extCSD from backup!!!
extCSD file...C:\Program Files\Z3X\EASYJTAG\Backups\VTU00M_2555642580_20140 105_2045.extcsd
Running:Repair extCSD...

Successfully connected to box on COM58
Box S/N: 0D01100B3AC50D82, ,FW Ver.: 01.48
Loading eMMC Addon Firmware...
Warning: CMD Pullup Level (1196 mV) too low , check cables etc.!!!
CMD Active Level:1639 mV
EMMC CID 15010056545530304DF1985402D47FD7
EMMC CSD D02701320F5903FFF6DBFFFF8E40406D
EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 07/2012 FW rev.0xf1
EMMC NAME: VTU00M , S/N: 2555642580
EMMC ROM1 (Main User Data) Capacity: 15028 MB (High Density Card)
EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB
EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
Extended CSD rev 1.6 (MMC 4.5)
Boot configuration [PARTITION_CONFIG: 0x48] Boot from:ROM2 (Boot Partition 1)
Boot bus config [177]: 0x01 , width 4bits , Partition config [179]: 0x48.
Writing...
eMMC ACK Error !!!
eMMC ACK Error !!!
eMMC ACK Error !!!
eMMC ACK Error !!!
eMMC ACK Error !!!
Done!
Writing file...D:\SAMSUNG\z3x easy\i9300\EMMC_ROM2_00000000_00200000.bin

Successfully connected to box on COM58
Box S/N: 0D01100B3AC50D82, ,FW Ver.: 01.48
Loading eMMC Addon Firmware...
Warning: CMD Pullup Level (1185 mV) too low , check cables etc.!!!
CMD Active Level:1639 mV
EMMC CID 15010056545530304DF1985402D47FD7
EMMC CSD D02701320F5903FFF6DBFFFF8E40406D
EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 07/2012 FW rev.0xf1
EMMC NAME: VTU00M , S/N: 2555642580
EMMC ROM1 (Main User Data) Capacity: 15028 MB (High Density Card)
EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB
EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
Extended CSD rev 1.6 (MMC 4.5)
Boot configuration [PARTITION_CONFIG: 0x48] Boot from:ROM2 (Boot Partition 1)
Boot bus config [177]: 0x01 , width 4bits , Partition config [179]: 0x48.
Writing 000000200000 bytes to 00000000 ...ROM2
Write Speed: 218 kB/s
Done !!!
Writing file...D:\SAMSUNG\z3x easy\i9300\EMMC_ROM1_512Mb_USER\EMMC_ROM1_00000000 _20000000.bin

Successfully connected to box on COM58
Box S/N: 0D01100B3AC50D82, ,FW Ver.: 01.48
Loading eMMC Addon Firmware...
Warning: CMD Pullup Level (1185 mV) too low , check cables etc.!!!
CMD Active Level:1639 mV
EMMC CID 15010056545530304DF1985402D47FD7
EMMC CSD D02701320F5903FFF6DBFFFF8E40406D
EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 07/2012 FW rev.0xf1
EMMC NAME: VTU00M , S/N: 2555642580
EMMC ROM1 (Main User Data) Capacity: 15028 MB (High Density Card)
EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB
EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
Extended CSD rev 1.6 (MMC 4.5)
Boot configuration [PARTITION_CONFIG: 0x48] Boot from:ROM2 (Boot Partition 1)
Boot bus config [177]: 0x01 , width 4bits , Partition config [179]: 0x48.
Writing 000020000000 bytes to 00000000 ...ROM1
Write Speed: 302 kB/s
Done !!!

mehmet_iletişim · 02-14-2014, 20:55

well done .

Sent from my iPhone using Tapatalk 2

skyulock · 02-15-2014, 07:34

Bro wish windows you users w7 or windows xp 3

cangsm · 02-15-2014, 08:53

windows xp 3 use No problem

skyulock · 02-15-2014, 10:25

Quote:

Originally Posted by cangsm

windows xp 3 use No problem

With windon 7 also problem rl100plb...........

lunno · 02-15-2014, 16:27

What the steps did you use?

cangsm · 02-15-2014, 17:50

Step 1: Smart Factory Reset + Format
Step 2: SAMSUNG: movinand Format
Step 3: Repair extcsd
Step 4: rom2 (Boot Partition 1) Select 2 MB Write
Step 5: ROM1 (Main user data), select 512 MB Write
work phone

tahamsa · 02-17-2014, 17:59

i have 24pcs i9300 without product name and i tried to flash emmc ic through easy jtag but every one showing this error

EasyJtag Suite ver.: 1.0.100.0 started.
Operating system ver.: Windows 7 (build 7601, Service Pack 1), 64-bit edition.
Successefuly connected to box on COM90
Box S/N: 121202160D62CBA3, ,FW Ver.: 01.48
Box Working Mode: JTAG Box.
Box Drivers version: 3.0.0.0, are OK
Z3X Card Serial : AAA9-C0E9 , ver: 22

Successfully connected to box on COM90
Box S/N: 121202160D62CBA3, ,FW Ver.: 01.48
Loading eMMC Addon Firmware...
Warning: CMD Pullup Level (1062 mV) too low , check cables etc.!!!
CMD Active Level:1515 mV
Can't Init EMMC !!! ( Ready Condition TIMEOUT! )
eMMC Card initialisation error!

i thing it may be bad emmc chip , am not sure
if anybody know about the error plz help

swechacnu · 02-17-2014, 19:10

Quote:

Originally Posted by tahamsa

i have 24pcs i9300 without product name and i tried to flash emmc ic through easy jtag but every one showing this error

EasyJtag Suite ver.: 1.0.100.0 started.
Operating system ver.: Windows 7 (build 7601, Service Pack 1), 64-bit edition.
Successefuly connected to box on COM90
Box S/N: 121202160D62CBA3, ,FW Ver.: 01.48
Box Working Mode: JTAG Box.
Box Drivers version: 3.0.0.0, are OK
Z3X Card Serial : AAA9-C0E9 , ver: 22

Successfully connected to box on COM90
Box S/N: 121202160D62CBA3, ,FW Ver.: 01.48
Loading eMMC Addon Firmware...
Warning: CMD Pullup Level (1062 mV) too low , check cables etc.!!!
CMD Active Level:1515 mV
Can't Init EMMC !!! ( Ready Condition TIMEOUT! )
eMMC Card initialisation error!

i thing it may be bad emmc chip , am not sure
if anybody know about the error plz help

Hi,

Give screenshot here when its download mode that screenshot,
in download mode if it showing custom binary NO
after that confirm EMMC damaged, but once again u need to check sold wires and power supply, if it will clear, replace emmc ic.

BR,
Srinivas Reddy.

cangsm · 02-17-2014, 21:02

Quote:

Originally Posted by tahamsa

i have 24pcs i9300 without product name and i tried to flash emmc ic through easy jtag but every one showing this error

EasyJtag Suite ver.: 1.0.100.0 started.
Operating system ver.: Windows 7 (build 7601, Service Pack 1), 64-bit edition.
Successefuly connected to box on COM90
Box S/N: 121202160D62CBA3, ,FW Ver.: 01.48
Box Working Mode: JTAG Box.
Box Drivers version: 3.0.0.0, are OK
Z3X Card Serial : AAA9-C0E9 , ver: 22

Successfully connected to box on COM90
Box S/N: 121202160D62CBA3, ,FW Ver.: 01.48
Loading eMMC Addon Firmware...
Warning: CMD Pullup Level (1062 mV) too low , check cables etc.!!!
CMD Active Level:1515 mV
Can't Init EMMC !!! ( Ready Condition TIMEOUT! )
eMMC Card initialisation error!

i thing it may be bad emmc chip , am not sure
if anybody know about the error plz help

Step 1 is your fault: Warning: CMD pullup Level (1062 mV) too low, check cables
Step 2 wire control
step 3 voltage control

Azacomseraa · 02-18-2014, 20:23

i9300 boot repair plase help!

Successfully connected to box on COM91
Box S/N: --------------, ,FW Ver.: 01.48
Loading eMMC Addon Firmware...
Warning: CMD Pullup Level (1082 mV) too low , check cables etc.!!!
CMD Active Level:1041 mV
Warning: CMD Active Level Low !!!
EMMC CID 15010056545530304DF1CC5C4F826FBF
EMMC CSD D02701320F5903FFF6DBFFFF8E40406D
EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 06/2012 FW rev.0xf1
EMMC NAME: VTU00M , S/N: 3428601730
EMMC ROM1 (Main User Data) Capacity: 15028 MB (High Density Card)
EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB
EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
Extended CSD rev 1.6 (MMC 4.5)
Boot configuration [PARTITION_CONFIG: 0x48] Boot from:ROM2 (Boot Partition 1)
Boot bus config [177]: 0x01 , width 4bits , Partition config [179]: 0x48.
Writing 000000200000 bytes to 00000000 ...ROM2
Retry writing adress 0x00000000
Retry writing adress 0x00000000
Retry writing adress 0x00000000
Retry writing adress 0x00000000

cangsm · 02-18-2014, 20:27

Quote:

Originally Posted by Azacomseraa

i9300 boot repair plase help!

Successfully connected to box on COM91
Box S/N: --------------, ,FW Ver.: 01.48
Loading eMMC Addon Firmware...
Warning: CMD Pullup Level (1082 mV) too low , check cables etc.!!!
CMD Active Level:1041 mV
Warning: CMD Active Level Low !!!
EMMC CID 15010056545530304DF1CC5C4F826FBF
EMMC CSD D02701320F5903FFF6DBFFFF8E40406D
EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 06/2012 FW rev.0xf1
EMMC NAME: VTU00M , S/N: 3428601730
EMMC ROM1 (Main User Data) Capacity: 15028 MB (High Density Card)
EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB
EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
Extended CSD rev 1.6 (MMC 4.5)
Boot configuration [PARTITION_CONFIG: 0x48] Boot from:ROM2 (Boot Partition 1)
Boot bus config [177]: 0x01 , width 4bits , Partition config [179]: 0x48.
Writing 000000200000 bytes to 00000000 ...ROM2
Retry writing adress 0x00000000
Retry writing adress 0x00000000
Retry writing adress 0x00000000
Retry writing adress 0x00000000

To program on the phone???

skyulock · 02-18-2014, 23:10

Quote:

Originally Posted by cangsm

Step 1 is your fault: Warning: CMD pullup Level (1062 mV) too low, check cables
Step 2 wire control
step 3 voltage control

bro you round because i have like 20 fone in hand is write this error

lunno · 02-20-2014, 18:56

I always get this error:

Loading eMMC Addon Firmware...
Warning: CMD Pullup Level (783 mV) too low , check cables etc.!!!
CMD Active Level:1258 mV
Warning: CMD Active Level Low !!!
eMMC ACK Error ( Check Connection )
eMMC Card initialisation error!

Azacomseraa · 02-20-2014, 19:14

plase help I9300 no product

Successfully connected to box on COM91
Box S/N: -----------------, ,FW Ver.: 01.48
Loading eMMC Addon Firmware...
CMD Pullup Level:1670 mV
CMD Active Level:1134 mV
Warning: CMD Active Level Low !!!
Can't Init EMMC !!! ( Ready Condition TIMEOUT! )
eMMC Card initialisation error!

02-14-2014, 20:53	#1 (permalink)
cangsm Insane Poster Join Date: May 2007 Posts: 90 Member: 516790 Status: Offline Thanks Meter: 19	i9300 NO PRODUCT (S3) - successfully repair with easy jtag Loading eMMC Addon Firmware... Warning: CMD Pullup Level (1196 mV) too low , check cables etc.!!! CMD Active Level:1650 mV EMMC CID 15010056545530304DF1985402D47FD7 EMMC CSD D02701320F5903FFF6DBFFFF8E40406D EMMC Manufacturer ID: 0015 , OEM ID: 0100 EMMC Date: 07/2012 FW rev.0xf1 EMMC NAME: VTU00M , S/N: 2555642580 EMMC ROM1 (Main User Data) Capacity: 15028 MB (High Density Card) EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB Extended CSD rev 1.6 (MMC 4.5) Boot configuration [PARTITION_CONFIG: 0x48] Boot from:ROM2 (Boot Partition 1) Boot bus config [177]: 0x01 , width 4bits , Partition config [179]: 0x48. Backup saved: VTU00M_2555642580_20140105_2045.extcsd Done. Running:SAMSUNG: Smart Factory Reset + Format... Successfully connected to box on COM58 Box S/N: 0D01100B3AC50D82, ,FW Ver.: 01.48 Loading eMMC Addon Firmware... Warning: CMD Pullup Level (1185 mV) too low , check cables etc.!!! CMD Active Level:1639 mV EMMC CID 15010056545530304DF1985402D47FD7 EMMC CSD D02701320F5903FFF6DBFFFF8E40406D EMMC Manufacturer ID: 0015 , OEM ID: 0100 EMMC Date: 07/2012 FW rev.0xf1 EMMC NAME: VTU00M , S/N: 2555642580 EMMC ROM1 (Main User Data) Capacity: 15028 MB (High Density Card) EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB Extended CSD rev 1.6 (MMC 4.5) Boot configuration [PARTITION_CONFIG: 0x48] Boot from:ROM2 (Boot Partition 1) Boot bus config [177]: 0x01 , width 4bits , Partition config [179]: 0x48. Backup saved: VTU00M_2555642580_20140105_2047.extcsd Sending Smart Wipe Request... Wiping Card... Please do not touch it!!! Done. Please don't forget to repair extCSD from backup!!! Running:SAMSUNG: MoviNAND Format... Successfully connected to box on COM58 Box S/N: 0D01100B3AC50D82, ,FW Ver.: 01.48 Loading eMMC Addon Firmware... CMD Pullup Level:1206 mV CMD Active Level:1639 mV EMMC CID 15010056545530304DF1985402D47FD7 EMMC CSD D02701320F5903FFF6DBFFFF8E40406D EMMC Manufacturer ID: 0015 , OEM ID: 0100 EMMC Date: 07/2012 FW rev.0xf1 EMMC NAME: VTU00M , S/N: 2555642580 EMMC ROM1 (Main User Data) Capacity: 15028 MB (High Density Card) EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB Extended CSD rev 1.6 (MMC 4.5) Boot configuration [PARTITION_CONFIG: 0x48] Boot from:ROM2 (Boot Partition 1) Boot bus config [177]: 0x01 , width 4bits , Partition config [179]: 0x48. Backup saved: VTU00M_2555642580_20140105_2047.extcsd Sending Internal Reconfiguration Request... Waiting configuration Apply!!! Restoring configuration... EMMC ROM2/3 (Boot Partitions) Capacity: 2048 kB EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB Wiping Card... Please do not touch it!!! Done. Please don't forget to repair extCSD from backup!!! extCSD file...C:\Program Files\Z3X\EASYJTAG\Backups\VTU00M_2555642580_20140 105_2045.extcsd Running:Repair extCSD... Successfully connected to box on COM58 Box S/N: 0D01100B3AC50D82, ,FW Ver.: 01.48 Loading eMMC Addon Firmware... Warning: CMD Pullup Level (1196 mV) too low , check cables etc.!!! CMD Active Level:1639 mV EMMC CID 15010056545530304DF1985402D47FD7 EMMC CSD D02701320F5903FFF6DBFFFF8E40406D EMMC Manufacturer ID: 0015 , OEM ID: 0100 EMMC Date: 07/2012 FW rev.0xf1 EMMC NAME: VTU00M , S/N: 2555642580 EMMC ROM1 (Main User Data) Capacity: 15028 MB (High Density Card) EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB Extended CSD rev 1.6 (MMC 4.5) Boot configuration [PARTITION_CONFIG: 0x48] Boot from:ROM2 (Boot Partition 1) Boot bus config [177]: 0x01 , width 4bits , Partition config [179]: 0x48. Writing... eMMC ACK Error !!! eMMC ACK Error !!! eMMC ACK Error !!! eMMC ACK Error !!! eMMC ACK Error !!! Done! Writing file...D:\SAMSUNG\z3x easy\i9300\EMMC_ROM2_00000000_00200000.bin Successfully connected to box on COM58 Box S/N: 0D01100B3AC50D82, ,FW Ver.: 01.48 Loading eMMC Addon Firmware... Warning: CMD Pullup Level (1185 mV) too low , check cables etc.!!! CMD Active Level:1639 mV EMMC CID 15010056545530304DF1985402D47FD7 EMMC CSD D02701320F5903FFF6DBFFFF8E40406D EMMC Manufacturer ID: 0015 , OEM ID: 0100 EMMC Date: 07/2012 FW rev.0xf1 EMMC NAME: VTU00M , S/N: 2555642580 EMMC ROM1 (Main User Data) Capacity: 15028 MB (High Density Card) EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB Extended CSD rev 1.6 (MMC 4.5) Boot configuration [PARTITION_CONFIG: 0x48] Boot from:ROM2 (Boot Partition 1) Boot bus config [177]: 0x01 , width 4bits , Partition config [179]: 0x48. Writing 000000200000 bytes to 00000000 ...ROM2 Write Speed: 218 kB/s Done !!! Writing file...D:\SAMSUNG\z3x easy\i9300\EMMC_ROM1_512Mb_USER\EMMC_ROM1_00000000 _20000000.bin Successfully connected to box on COM58 Box S/N: 0D01100B3AC50D82, ,FW Ver.: 01.48 Loading eMMC Addon Firmware... Warning: CMD Pullup Level (1185 mV) too low , check cables etc.!!! CMD Active Level:1639 mV EMMC CID 15010056545530304DF1985402D47FD7 EMMC CSD D02701320F5903FFF6DBFFFF8E40406D EMMC Manufacturer ID: 0015 , OEM ID: 0100 EMMC Date: 07/2012 FW rev.0xf1 EMMC NAME: VTU00M , S/N: 2555642580 EMMC ROM1 (Main User Data) Capacity: 15028 MB (High Density Card) EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB Extended CSD rev 1.6 (MMC 4.5) Boot configuration [PARTITION_CONFIG: 0x48] Boot from:ROM2 (Boot Partition 1) Boot bus config [177]: 0x01 , width 4bits , Partition config [179]: 0x48. Writing 000020000000 bytes to 00000000 ...ROM1 Write Speed: 302 kB/s Done !!!

02-17-2014, 17:59	#8 (permalink)
tahamsa Junior Member Join Date: Feb 2013 Posts: 5 Member: 1891212 Status: Offline Thanks Meter: 1	i9300 no product name error i have 24pcs i9300 without product name and i tried to flash emmc ic through easy jtag but every one showing this error EasyJtag Suite ver.: 1.0.100.0 started. Operating system ver.: Windows 7 (build 7601, Service Pack 1), 64-bit edition. Successefuly connected to box on COM90 Box S/N: 121202160D62CBA3, ,FW Ver.: 01.48 Box Working Mode: JTAG Box. Box Drivers version: 3.0.0.0, are OK Z3X Card Serial : AAA9-C0E9 , ver: 22 Successfully connected to box on COM90 Box S/N: 121202160D62CBA3, ,FW Ver.: 01.48 Loading eMMC Addon Firmware... Warning: CMD Pullup Level (1062 mV) too low , check cables etc.!!! CMD Active Level:1515 mV Can't Init EMMC !!! ( Ready Condition TIMEOUT! ) eMMC Card initialisation error! i thing it may be bad emmc chip , am not sure if anybody know about the error plz help

02-14-2014, 20:55	#2 (permalink)
mehmet_iletişim Freak Poster Join Date: Aug 2006 Posts: 320 Member: 335721 Status: Offline Thanks Meter: 12	well done . Sent from my iPhone using Tapatalk 2

02-15-2014, 07:34	#3 (permalink)
skyulock No Life Poster Join Date: Apr 2008 Location: nigeria Posts: 1,307 Member: 757064 Status: Offline Sonork: 11111111 Thanks Meter: 365	Bro wish windows you users w7 or windows xp 3

02-15-2014, 08:53	#4 (permalink)
cangsm Insane Poster Join Date: May 2007 Posts: 90 Member: 516790 Status: Offline Thanks Meter: 19	windows xp 3 use No problem

02-15-2014, 16:27	#6 (permalink)
lunno Freak Poster Join Date: Dec 2012 Location: Brazil Posts: 216 Member: 1859706 Status: Offline Sonork: 100.1648492 Thanks Meter: 28	What the steps did you use?

02-15-2014, 17:50	#7 (permalink)
cangsm Insane Poster Join Date: May 2007 Posts: 90 Member: 516790 Status: Offline Thanks Meter: 19	Step 1: Smart Factory Reset + Format Step 2: SAMSUNG: movinand Format Step 3: Repair extcsd Step 4: rom2 (Boot Partition 1) Select 2 MB Write Step 5: ROM1 (Main user data), select 512 MB Write work phone

02-18-2014, 20:23	#11 (permalink)
Azacomseraa Freak Poster Join Date: Sep 2010 Location: Uzbekistan/Namangan/Sardoba Posts: 155 Member: 1396837 Status: Offline Sonork: 100.1657369 Thanks Meter: 17	i9300 boot repair plase help! Successfully connected to box on COM91 Box S/N: --------------, ,FW Ver.: 01.48 Loading eMMC Addon Firmware... Warning: CMD Pullup Level (1082 mV) too low , check cables etc.!!! CMD Active Level:1041 mV Warning: CMD Active Level Low !!! EMMC CID 15010056545530304DF1CC5C4F826FBF EMMC CSD D02701320F5903FFF6DBFFFF8E40406D EMMC Manufacturer ID: 0015 , OEM ID: 0100 EMMC Date: 06/2012 FW rev.0xf1 EMMC NAME: VTU00M , S/N: 3428601730 EMMC ROM1 (Main User Data) Capacity: 15028 MB (High Density Card) EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB Extended CSD rev 1.6 (MMC 4.5) Boot configuration [PARTITION_CONFIG: 0x48] Boot from:ROM2 (Boot Partition 1) Boot bus config [177]: 0x01 , width 4bits , Partition config [179]: 0x48. Writing 000000200000 bytes to 00000000 ...ROM2 Retry writing adress 0x00000000 Retry writing adress 0x00000000 Retry writing adress 0x00000000 Retry writing adress 0x00000000

02-20-2014, 18:56	#14 (permalink)
lunno Freak Poster Join Date: Dec 2012 Location: Brazil Posts: 216 Member: 1859706 Status: Offline Sonork: 100.1648492 Thanks Meter: 28	I always get this error: Loading eMMC Addon Firmware... Warning: CMD Pullup Level (783 mV) too low , check cables etc.!!! CMD Active Level:1258 mV Warning: CMD Active Level Low !!! eMMC ACK Error ( Check Connection ) eMMC Card initialisation error!

02-20-2014, 19:14	#15 (permalink)
Azacomseraa Freak Poster Join Date: Sep 2010 Location: Uzbekistan/Namangan/Sardoba Posts: 155 Member: 1396837 Status: Offline Sonork: 100.1657369 Thanks Meter: 17	plase help I9300 no product Successfully connected to box on COM91 Box S/N: -----------------, ,FW Ver.: 01.48 Loading eMMC Addon Firmware... CMD Pullup Level:1670 mV CMD Active Level:1134 mV Warning: CMD Active Level Low !!! Can't Init EMMC !!! ( Ready Condition TIMEOUT! ) eMMC Card initialisation error!