GSM-Forum - j100h too many error writing has been stop

GSM-Forum (https://forum.gsmhosting.com/vbb/)

- Easy-Jtag / Easy-Jtag Plus (https://forum.gsmhosting.com/vbb/f672/)

- - j100h too many error writing has been stop (https://forum.gsmhosting.com/vbb/f672/j100h-too-many-error-writing-has-been-stop-2421146/)

j100h too many error writing has been stop

hi
am facing these problem please can anyone help me out
am new user for easy jtag plus
Setting interface to EasyJtag2/ISP_HiPower
Setting bus width to 1 Bit
HiPower mode is ON
Setting frequence to 36 Mhz
CMD Pullup Level: 1824 mV
CMD Active Level: 1865 mV
EMMC Device Information :
EMMC CID: 90014A4834473262110190A76A6082A5
EMMC CSD: D07F01320F5903FFFFFFFFEF8A4040DB
EMMC Manufacture : SKHYNIX , EMMC NAME: H4G2b , HEX: 483447326200 , S/N: 90A76A60 , rev. 0x01
EMMC Manufacture ID: 0x90 , OEM ID: 0x4A , Device Type: BGA (Discrete embedded) , Date: 8/2015
EMMC ROM 1 (Main User Data) Capacity: 3728 MB (0000E9000000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000)
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.6 (MMC 4.5, MMC 4.51)
Boot configuration [PARTITION_CONFIG]: 0x08 , Boot from: ROM2 (Boot partition 1)
Boot Bus Config: 0x00 , width 1bit
H/W Reset Function [RST_N_FUNCTION]: 0x00, RST_n signal is temporarily disabled
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: H4G2b_90A76A60_20180617_222504.extcsd
EMMC Init completed.

Opening file: J13G.pit

Pit: J13G.pit
Entry count: 29

The size of the last section has been updated

BL_J100HXXU0AQA1_CL1167865_QB12130539_REV01_user_l ow_ship.tar.md5
The list of files in the firmware:
spl.img
sboot.bin
sboot2.bin
param.lfs

AP_J100HXXU0AQA1_CL1167865_QB12130539_REV01_user_l ow_ship.tar.md5
The list of files in the firmware:
boot.img
recovery.img
system.img

CP_J100HXXU0AQA1_CL1167865_QB12130539_REV01_user_l ow_ship.tar.md5
The list of files in the firmware:
sprdcp.img
sprddsp.img
nvitem.bin

CSC_OXE_J100HOXE0AQA1_CL1167865_QB12130539_REV01_u ser_low_ship.tar.md5
The list of files in the firmware:
j13g.pit
cache.img
hidden.img

Setting interface to EasyJtag2/ISP_HiPower
Setting bus width to 1 Bit
HiPower mode is ON
Setting frequence to 36 Mhz
CMD Pullup Level: 1824 mV
CMD Active Level: 1865 mV
EMMC Device Information :
EMMC CID: 90014A4834473262110190A76A6082A5
EMMC CSD: D07F01320F5903FFFFFFFFEF8A4040DB
EMMC Manufacture : SKHYNIX , EMMC NAME: H4G2b , HEX: 483447326200 , S/N: 90A76A60 , rev. 0x01
EMMC Manufacture ID: 0x90 , OEM ID: 0x4A , Device Type: BGA (Discrete embedded) , Date: 8/2015
EMMC ROM 1 (Main User Data) Capacity: 3728 MB (0000E9000000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000)
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.6 (MMC 4.5, MMC 4.51)
Boot configuration [PARTITION_CONFIG]: 0x08 , Boot from: ROM2 (Boot partition 1)
Boot Bus Config: 0x00 , width 1bit
H/W Reset Function [RST_N_FUNCTION]: 0x00, RST_n signal is temporarily disabled
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: H4G2b_90A76A60_20180617_222535.extcsd
EMMC Init completed.

Operation: Write by vendor (Samsung)

Creating GPT-partitioninig
Writing PrimaryGPT at address: 000000000000
Error writing at address: 000000000000 , error: 34 , 34 Unknown error ... Retry #1
Error writing at address: 000000000000 , error: 34 , 34 Unknown error ... Retry #2
Error writing at address: 000000000000 , error: 34 , 34 Unknown error ... Retry #3
Too many errors. Writing has been stopped

Setting interface to EasyJtag2/ISP_HiPower
Setting bus width to 1 Bit
HiPower mode is ON
Setting frequence to 36 Mhz
CMD Pullup Level: 1806 mV
CMD Active Level: 1865 mV
EMMC Device Information :
EMMC CID: 90014A4834473262110190A76A6082A5
EMMC CSD: D07F01320F5903FFFFFFFFEF8A4040DB
EMMC Manufacture : SKHYNIX , EMMC NAME: H4G2b , HEX: 483447326200 , S/N: 90A76A60 , rev. 0x01
EMMC Manufacture ID: 0x90 , OEM ID: 0x4A , Device Type: BGA (Discrete embedded) , Date: 8/2015
EMMC ROM 1 (Main User Data) Capacity: 3728 MB (0000E9000000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000)
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.6 (MMC 4.5, MMC 4.51)
Boot configuration [PARTITION_CONFIG]: 0x08 , Boot from: ROM2 (Boot partition 1)
Boot Bus Config: 0x00 , width 1bit
H/W Reset Function [RST_N_FUNCTION]: 0x00, RST_n signal is temporarily disabled
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: H4G2b_90A76A60_20180617_223145.extcsd
EMMC Init completed.

Operation: Write by vendor (Samsung)

Creating GPT-partitioninig
Writing PrimaryGPT at address: 000000000000
Error writing at address: 000000000000 , error: 34 , 34 Unknown error ... Retry #1
Error writing at address: 000000000000 , error: 34 , 34 Unknown error ... Retry #2
Error writing at address: 000000000000 , error: 34 , 34 Unknown error ... Retry #3
Too many errors. Writing has been stopped

snyone can help me please
thanks in advance

You cannot writes data to that EMMC.

Soft doesn't support or EMMC is BAD.

it's SKHINIX emmc. try to uni-format/reset & repartitions.

But it's not guaranteed the handset will ok for a long time.
some time it just ok a week or even a day.

and now these showing am sorry am new with JTAG
Loading eMMC GEN2 Firmware... IO: 2800 mV
Box S/N: 16F03C9E6AE1BE10, ,FW Ver.: 02.23
CMD Pullup Level:2186 mV
CMD Active Level:2551 mV
Box IO Level:2800 mV
CLK Rate:24000 kHz
Bus Width:1bit,SDR
HiPower mode is ON!
---------- eMMC Device Information ----------

EMMC CID : 90014A4834473262110190A76A6082A5
EMMC CSD : D07F01320F5903FFFFFFFFEF8A4040DB
EMMC Manufacturer ID: 0090 , OEM ID: 014A
EMMC Date: 08/2015 Rev.0x1
EMMC NAME: H4G2b , S/N: 2426890848
EMMC NAME (HEX): 48344732622000
EMMC ROM1 (Main User Data) Capacity: 3728 MB
EMMC ROM2 (Boot Partition 1) Capacity: 4096 kB
EMMC ROM3 (Boot Partition 2) Capacity: 4096 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 kB
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
EMMC Password Locked: No
Extended CSD rev 1.6 (MMC 4.5)
Boot configuration [PARTITION_CONFIG: 0x08] Boot from:ROM2 (Boot Partition 1)
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x08.
H/W reset function [RST_N_FUNCTION]: 0x00
High-capacity W protect group size [HC_WP_GRP_SIZE: 0x00000000]
Partitioning Support [PARTITIONING_SUPPORT]: 0x07
Device support partitioning feature
Device can have enhanced tech.
Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00
---------------------------------------------
Backup saved: H4G2b _2426890848_20180618_2255.extcsd
Done.

Checking NAND Image : D:\Compressed\SM-J100h_J100HXCU0AOD4_ROM1_OK\SM-J100h_J100HXCU0AOD4_ROM1_OK.bin
Autodetected RAW data
Warning! Disk size is smaller than the main header indicates! Loading
Caution: invalid backup GPT header, but valid main header!
EFI Table CRC Check FAIL.
Warning! One or more CRCs don't match. You should repair the disk!
Partition table scan:
GPT: damaged
Caution: Found protective or hybrid MBR and corrupt GPT.
Partition info successfully found
Linux partitions is not found in image...
File successefuly loaded!

Real (Hardware) Disk/Image size: 200000 sectors 1024.0 MiB
Soft (Partitioned) Disk/Image size: 743FBC sectors 3.6 GiB
Logical sector size: 0x200 bytes
Disk identifier (GUID): 52444E41-494F-2044-4D4D-43204449534B
First usable sector: 34
Last usable sector: 7618526
Processing file...D:\Compressed\SM-J100h_J100HXCU0AOD4_ROM1_OK\SM-J100h_J100HXCU0AOD4_ROM1_OK.bin
Writing as RAW data
Checking security ...
Z3X EasyJtag Software ver. 2.9.0.3
Skip loading eMMC Addon Firmware
CMD Pullup Level:2191 mV
CMD Active Level:2789 mV
Input file : D:\Compressed\SM-J100h_J100HXCU0AOD4_ROM1_OK\SM-J100h_J100HXCU0AOD4_ROM1_OK.bin
Writing 0040000000 bytes to 0000000000... ROM1 (USER ROM)
Error writing address 0x38220000 Error Code:-4 Reason :DATA RCV CRC Error
Retry writing address 0x0038220000 (Attempt #0)...
Retry failed at address 0x38220000 Error Code:-4 Reason :DATA RCV CRC Error
Retry writing address 0x0038220000 (Attempt #0)...
Retry failed at address 0x38220000 Error Code:-4 Reason :DATA RCV CRC Error
Retry writing address 0x0038220000 (Attempt #0)...
Retry failed at address 0x38220000 Error Code:-4 Reason :DATA RCV CRC Error
Retry writing address 0x0038220000 (Attempt #0)...

Setting interface to EasyJtag2/ISP
Setting bus width to 1 Bit
Setting frequence to 36 Mhz
CMD Pullup Level: 2075 mV
CMD Active Level: 2655 mV
EMMC Device Information :
EMMC CID: 90014A48344732621101632A64393299
EMMC CSD: D07F01320F5903FFFFFFFFEF8A4040DB
EMMC Manufacture : SKHYNIX , EMMC NAME: H4G2b , HEX: 483447326200 , S/N: 632A6439 , rev. 0x01
EMMC Manufacture ID: 0x90 , OEM ID: 0x4A , Device Type: BGA (Discrete embedded) , Date: 3/2015
EMMC ROM 1 (Main User Data) Capacity: 3728 MB (0000E9000000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000)
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.6 (MMC 4.5, MMC 4.51)
Boot configuration [PARTITION_CONFIG]: 0x08 , Boot from: ROM2 (Boot partition 1)
Boot Bus Config: 0x00 , width 1bit
H/W Reset Function [RST_N_FUNCTION]: 0x00, RST_n signal is temporarily disabled
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: H4G2b_632A6439_20180619_185425.extcsd
EMMC Init completed.

Operation: Write by vendor (Samsung)

Unpacking file: sboot.bin
Unpacking file: sboot2.bin
Unpacking file: param.lfs

Partition name: SBOOT
Filename: sboot.bin , Offset: 000000400000 , filesize: 1573888 bytes
eMMC switching to ROM1
Writing partition...
Error writing at address: 000000400000 , error: 1792, 1792 Unknown error ... Retry #1
Error writing at address: 000000400000 , error: 1792, 1792 Unknown error ... Retry #2
Error writing at address: 000000400000 , error: 1792, 1792 Unknown error ... Retry #3
Too many errors. Writing has been stopped

1.5.0-1.5.1 have bug with some Hynix flash IC - bad I/O level detect

try to use 1.4.9, we try to fix it at 1.5.2

I Have J100h This Problem How TO Solution

Get firmware version
Error reading at address: 000000000000 , error: -2, CMD CRC Error ... Retry #1
Error reading at address: 000000000000 , error: -4, DATA RCV CRC Error ... Retry #2
Error reading at address: 000000000000 , error: -4, DATA RCV CRC Error ... Retry #3
Error reading at address: 000000000000 , error: -2, CMD CRC Error ... Retry #4
Error reading at address: 000000000000 , error: -4, DATA RCV CRC Error ... Retry #5
Too many errors. Reading has been stopped

Any Body Help Me My Samsung J100H Date But Easy Jtag Repair
But Not Working

Setting frequence to 21 Mhz
CMD Pullup Level: 422 mV
CMD Active Level: 2990 mV
EMMC Device Information :
EMMC CID: 90014A48344732621101F0281A2B5256
EMMC CSD: D07F01320F5903FFFFFFFFEF8A4040DA
EMMC Manufacture Name: SKHYNIX , EMMC NAME: H4G2b , EMMC NAME (HEX): 483447326200 , S/N: F0281A2B , rev. 0x01
EMMC Manufacture ID: 0x90 , OEM ID: 0x4A , Device Type: BGA (Discrete embedded) , Manufacture Date: 5/2015
EMMC ROM 1 (Main User Data) Capacity: 3728 MB (0000E9000000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000)
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.6 (MMC 4.5, MMC 4.51)
Boot configuration [PARTITION_CONFIG]: 0x08 , Boot from: ROM2 (Boot partition 1)
Boot Bus Config: 0x00 , width 1bit
H/W Reset Function [RST_N_FUNCTION]: 0x00, RST_n signal is temporarily disabled
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: H4G2b_F0281A2B_20190326_173816.extcsd
EMMC Init completed.

Get firmware version
Error reading at address: 000000000000 , error: -2, CMD CRC Error ... Retry #1
Error reading at address: 000000000000 , error: -4, DATA RCV CRC Error ... Retry #2
Error reading at address: 000000000000 , error: -4, DATA RCV CRC Error ... Retry #3
Error reading at address: 000000000000 , error: -2, CMD CRC Error ... Retry #4
Error reading at address: 000000000000 , error: -4, DATA RCV CRC Error ... Retry #5
Too many errors. Reading has been stopped

Quote:

Originally Posted by abdul alim (Post 13595081)

CMD pullup is low

if you use Old EasyJTAG box, you need solder pull-up resistors 100-200-500 Ohm for CMD, D_0 line or use Hipower CLK mode (connec togewer 4 pins and use usb power instead of 1,8/2,8 from adapter)

i have solution 100000%;)

remove emmc dont use isp then i think u get success.

Salect low clock 18mhz and try again

bro use easy jtag plus setup

first format universal emmc

second creat partion

after write repair excsd

write room 2

room 3

room 1

ur fhone 1000ok no any error

Quote:

Originally Posted by akash48 (Post 13602351)

bro use easy jtag plus setup

first format universal emmc

second creat partion

after write repair excsd

write room 2

room 3

room 1

ur fhone 1000ok no any error

1) Erase eMMC of Format
2) Write boot config
3) Write ROM1 (and ROM2/3 if needed)

Setting interface to EasyJtag2/ISP_HiPower
Setting bus width to 1 Bit
HiPower mode is ON
Setting frequence to 36 MHz
CMD Pullup Level: 642 mV
CMD Active Level: 2023 mV
EMMC Device Information :
EMMC CID: 15010056594C30304D19B31E4BB85E61
EMMC CSD: D02701320F5903FFF6DBFFEF8A404067
EMMC Manufacture : SAMSUNG , EMMC NAME: VYL00M , HEX: 56594C30304D , S/N: B31E4BB8 , rev. 0x19
EMMC Manufacture ID: 0x15 , OEM ID: 0x00 , Device Type: BGA (Discrete embedded) , Date: 5/2011
EMMC ROM 1 (Main User Data) Capacity: 15028 MB (0003AB400000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 512 KB (000000080000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 KB (000000020000) Counter: 0 , Response: Clean
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.5 (MMC 4.41)
Boot configuration [PARTITION_CONFIG]: 0x48 , Boot from: ROM2 (Boot partition 1)
Boot Bus Config: 0x01 , width 4bit
H/W Reset Function [RST_N_FUNCTION]: 0x00, RST_n signal is temporarily disabled
Supported partition features [PARTITIONING_SUPPORT]: 0x03
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: VYL00M_B31E4BB8_20201122_184833.extcsd
EMMC Init completed.

Operation: Writing eMMC...

Writing to: ROM1 , start: 0x000000000000 , size: 0x000020000000
Input file: E:\I9100\Samsung_GT-i9100_model_dump_rom1_512mb_fixed\Samsung_GT-i9100_model_dump_rom1_512mb.BIN
eMMC switching to ROM1
Writing partition...
Error writing at address: 000000000000 , error: -8, DATA SND CRC Error(Small ROM Size, maybe) ... Retry #1
Error writing at address: 000000000000 , error: -1, CMD Timeout Error ... Retry #2
Error writing at address: 000000000000 , error: -1, CMD Timeout Error ... Retry #3
Too many errors. Writing has been stopped