May someone explain if i can revive this a530f 2018

[chitawira]

Setting interface to EasyJtag2/ISP
Setting bus width to 1 Bit
Setting frequence to 36 MHz
CMD Pullup Level: 463 mV
CMD Active Level: 1375 mV
EMMC Device Information :
EMMC CID: 150100424A54443452000684ECE174F9
EMMC CSD: 902701320F5903FFF6DB7FE08A40403B
EMMC Manufacture : SAMSUNG , EMMC NAME: BJTD4R , HEX: 424A54443452 , S/N: 0684Exxx , rev. 0x00
EMMC Manufacture ID: 0x15 , OEM ID: 0x00 , Device Type: BGA (Discrete embedded) , Date: 7/2017
EMMC ROM 1 (Main User Data) Capacity: 29820 MB (000747C00000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 0 KB (000000000000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 0 KB (000000000000) Counter: 0 , Response: Clean
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.8 (MMC 5.1)
Boot configuration [PARTITION_CONFIG]: 0x48 , Boot from: ROM2 (Boot partition 1)
Boot Bus Config: 0x01 , width 4bit
H/W Reset Function [RST_N_FUNCTION]: 0x00, RST_n signal is temporarily disabled
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: BJTD4R_0684ECE1_20210531_003055.extcsd
EMMC Init completed.

Scanning soft partitions
Partition table not found

PROBLEM IS :PARTITION TABLE NOT FOUND

[CoMoBat]

Originally Posted by chitawira

Setting interface to EasyJtag2/ISP
Setting bus width to 1 Bit
Setting frequence to 36 MHz
CMD Pullup Level: 463 mV
CMD Active Level: 1375 mV
EMMC Device Information :
EMMC CID: 150100424A54443452000684ECE174F9
EMMC CSD: 902701320F5903FFF6DB7FE08A40403B
EMMC Manufacture : SAMSUNG , EMMC NAME: BJTD4R , HEX: 424A54443452 , S/N: 0684Exxx , rev. 0x00
EMMC Manufacture ID: 0x15 , OEM ID: 0x00 , Device Type: BGA (Discrete embedded) , Date: 7/2017
EMMC ROM 1 (Main User Data) Capacity: 29820 MB (000747C00000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 0 KB (000000000000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 0 KB (000000000000) Counter: 0 , Response: Clean
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.8 (MMC 5.1)
Boot configuration [PARTITION_CONFIG]: 0x48 , Boot from: ROM2 (Boot partition 1)
Boot Bus Config: 0x01 , width 4bit
H/W Reset Function [RST_N_FUNCTION]: 0x00, RST_n signal is temporarily disabled
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: BJTD4R_0684ECE1_20210531_003055.extcsd
EMMC Init completed.

Scanning soft partitions
Partition table not found

PROBLEM IS :PARTITION TABLE NOT FOUND

try to write emmc firmware and see result

[chitawira]

I try to write the emmc firmware and all went in fine but still same error partion not found,then i tried with eMMC tool version 2.0.10 (release date:05.05.2021) below is the log with Rom 2 error. Where can i get ROM2, ROM 3 and ROM 1 for this particular A8 2018 A530F DS


Operation: Connect to Z3X EasyJtagPlus

Setting Interface to EasyJtag2/ISP
Setting IO Levels to 3.3V
Setting Frequence to 36 Mhz
Setting BusWidth to 1 Bit
CMD Pullup Level: 462 mV
CMD Active Level: 1374 mV
Setting HS Timing to Enabled

EMMC Device Information :
EMMC CID: 150100424A54443452000684ECE174F9
EMMC CSD: 902701320F5903FFF6DB7FE08A40403B
Manufacturer: SAMSUNG , NAME: BJTD4R , HEX: 424A54443452 , S/N: 0684ECxx , Rev: 00
Manufacturer ID: 15 , OEM ID: 00 , Device Type: BGA (Discrete embedded) , Date: 7/2017
EMMC ROM 1 (Main User Data) Capacity: 29820 MB (0x000747C00000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 0 KB (0x000000000000)
EMMC RPMB Capacity: 0 KB (0x000000000000) , Counter: 0 , Response: Clean
Extended CSD Information :
Extended CSD rev: 1.8 (MMC 5.1)
Boot configuration [PARTITION_CONFIG]: 0x48 , Boot partition 1 enabled for boot , Boot ACK
Boot Bus Config: 0x01 , x4 (sdr/ddr) bus width in boot operation mode
H/W Reset Function [RST_N_FUNCTION]: 0x00 , RST_n signal is temporarily disabled
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition settings [PARTITION_SETTING_COMPLETED]: 0x00
EMMC Init completed
Extcsd backup saved: BJTD4R_0684ECE1_20210529_213519.extcsd (old backup)

Connected successfully

Operation: Scan PartitionTable from Source (Vendor: Binary Read/Write)

Scanning soft partitions from ROM2
Error reading at address: 000000000000 , error: -3, DATA RCV Timeout Error ... Retry #1
Error reading at address: 000000000000 , error: -3, DATA RCV Timeout Error ... Retry #2
Error reading at address: 000000000000 , error: -3, DATA RCV Timeout Error ... Retry #3

Canceled