GSM-Forum

GSM-Forum (https://forum.gsmhosting.com/vbb/)
-   Easy-Jtag / Easy-Jtag Plus (https://forum.gsmhosting.com/vbb/f672/)
-   -   Oppo A3s [CPH1803][EDL MODE][DEAD RECOVERED][DONE] by Easy JTAG_Palash Ahammad (https://forum.gsmhosting.com/vbb/f672/oppo-a3s-cph1803-edl-mode-dead-recovered-done-easy-jtag_palash-ahammad-2813504/)

...:::::NP™:::::... 03-03-2020 16:07

Oppo A3s [CPH1803][EDL MODE][DEAD RECOVERED][DONE] by Easy JTAG_Palash Ahammad
 
@ All

Please don't remove CLK / CMD Resistance,

Before remove components, Just do you complete the procedure are below.



Step 1:-

Unfortunately when you got your Phone ''EDL'' Mode Problem.

(A) What can you do ?

1) Connect the I.S.P carefully accurate flow by the Pin out.

https://i.ibb.co/mRKmWg6/OPPO-A3-S-e...ect-pinout.jpg

2) Immediately create your security area / partitions backup read by vendor.

(B) How to backup security area / partitions. Read by vendor ?

Answer:-

Run ''EasyJTAG Plus'' set voltage manually which voltage sweet-able for your eMMC detected also set the frequency 1 mhz + Bus 1 bit.

Go to Read soft partitions then Check ''eMMC / UFS'' if you get all partitions is okay only your phone dose not run or EDL mode detected by 'PC" device manager.

No problem ! don't be upset !

Go to Read by vendor operation ''TAB" there are already all partitions are visible.

(C) Pay attention, You have need to be create Below the partitions backup very carefully.

*) config

*) fsg

*) sec

*) modem

*) modemst1

*) modemst2

*) oppodycnvbk

*) opporeserve2

*) oppostanvbk

*) Persist

https://i.ibb.co/pd38BVf/index.png

Unfortunately if your phone already has been full erase by mistake so you can restore only your B.B below the data write by vendor throw the Partitions.

OPPO A3S CPH1803EX_11_A.17_Samsung eMMC_oppodycnvbk + oppostanvbk + modemst1 + modemst2 + fsg + sec + modem.7z

Very important instruction, when you write the security area for restore your B.B must UN-trick reparation option as per below the image.


https://i.ibb.co/fdCMTY9/bb-recovery.png



(D) Go to eMMC General / Image ''TAB'' select Dump_OPPO A3S CPH1803EX_11_A.17_Samsung eMMC_ QE63MB_06_03_2020_16_08_12.bin

Mega Mirror ## Dump_OPPO A3S CPH1803EX_11_A.17_Samsung eMMC_ QE63MB


Code:


3/11/2020 1:17:49 AM> Operation: Writing eMMC...
3/11/2020 1:17:49 AM>
3/11/2020 1:17:49 AM> Writing to: ROM1 , start: 0x000000000000 , size: 0x00000FA00000
3/11/2020 1:17:50 AM> Input file: C:\Users\Dream\Downloads\OPPO A3S CPH1803EX_11_A.17_Samsung eMMC_ QE63MB_06_03_2020_16_08_12.bin
3/11/2020 1:17:50 AM> eMMC switching to ROM1
3/11/2020 1:17:50 AM> Writing partition...
3/11/2020 1:27:06 AM> Done writing partition. Write speed: 460.08 KB/s
3/11/2020 1:27:06 AM>
3/11/2020 1:27:06 AM> All done  time: [00:09:16:631]

Go To Scanning soft partitions
Code:

3/11/2020 1:27:47 AM> Scanning soft partitions
3/11/2020 1:27:47 AM> GPT header is found and is valid
3/11/2020 1:27:47 AM> Partition: oppodycnvbk, [000000005000 - 000000A05000], size: 000000A00000 (10.0 MB)
3/11/2020 1:27:47 AM> Partition: oppostanvbk, [000000A05000 - 000001405000], size: 000000A00000 (10.0 MB)
3/11/2020 1:27:47 AM> Partition: modemst1, [000001405000 - 000001585000], size: 000000180000 (1.50 MB)
3/11/2020 1:27:47 AM> Partition: modemst2, [000001585000 - 000001705000], size: 000000180000 (1.50 MB)
3/11/2020 1:27:47 AM> Partition: persist, [000001705000 - 000003705000], size: 000002000000 (32.0 MB)
3/11/2020 1:27:47 AM> Partition: opporeserve1, [000003705000 - 000003F05000], size: 000000800000 (8.00 MB)
3/11/2020 1:27:47 AM> Partition: opporeserve2, [000003F05000 - 000007F05000], size: 000004000000 (64.0 MB)
3/11/2020 1:27:47 AM> Partition: reserve_exp1, [000007F05000 - 000008105000], size: 000000200000 (2.00 MB)
3/11/2020 1:27:47 AM> Partition: reserve_exp2, [000008105000 - 000008305000], size: 000000200000 (2.00 MB)
3/11/2020 1:27:47 AM> Partition: fsc, [000008305000 - 000008305400], size: 000000000400 (1.00 KB)
3/11/2020 1:27:47 AM> Partition: ssd, [000008306000 - 000008308000], size: 000000002000 (8.00 KB)
3/11/2020 1:27:47 AM> Partition: sbl1, [000008308000 - 000008388000], size: 000000080000 (512. KB)
3/11/2020 1:27:47 AM> Partition: rpm, [000008388000 - 000008408000], size: 000000080000 (512. KB)
3/11/2020 1:27:47 AM> Partition: tz, [000008408000 - 000008608000], size: 000000200000 (2.00 MB)
3/11/2020 1:27:47 AM> Partition: devcfg, [000008608000 - 000008648000], size: 000000040000 (256. KB)
3/11/2020 1:27:47 AM> Partition: sbl1bak, [000008648000 - 0000086C8000], size: 000000080000 (512. KB)
3/11/2020 1:27:47 AM> Partition: rpmbak, [0000086C8000 - 000008748000], size: 000000080000 (512. KB)
3/11/2020 1:27:47 AM> Partition: tzbak, [000008748000 - 000008948000], size: 000000200000 (2.00 MB)
3/11/2020 1:27:47 AM> Partition: devcfgbak, [000008948000 - 000008988000], size: 000000040000 (256. KB)
3/11/2020 1:27:47 AM> Partition: dsp, [000008988000 - 000009988000], size: 000001000000 (16.0 MB)
3/11/2020 1:27:47 AM> Partition: DDR, [00000A000000 - 00000A008000], size: 000000008000 (32.0 KB)
3/11/2020 1:27:47 AM> Partition: fsg, [00000A008000 - 00000A188000], size: 000000180000 (1.50 MB)
3/11/2020 1:27:47 AM> Partition: sec, [00000A188000 - 00000A18C000], size: 000000004000 (16.0 KB)
3/11/2020 1:27:47 AM> Partition: aboot, [00000A18C000 - 00000A28C000], size: 000000100000 (1.00 MB)
3/11/2020 1:27:47 AM> Partition: abootbak, [00000A28C000 - 00000A38C000], size: 000000100000 (1.00 MB)
3/11/2020 1:27:47 AM> Partition: modem, [00000A38C000 - 00001238C000], size: 000008000000 (128. MB)
3/11/2020 1:27:47 AM> Partition: dtbo, [00001238C000 - 000012B8C000], size: 000000800000 (8.00 MB)
3/11/2020 1:27:47 AM> Partition: vbmeta, [000012B8C000 - 000012B9C000], size: 000000010000 (64.0 KB)
3/11/2020 1:27:47 AM> Partition: boot, [000012B9C000 - 000016B9C000], size: 000004000000 (64.0 MB)
3/11/2020 1:27:47 AM> Partition: recovery, [000016B9C000 - 00001AB9C000], size: 000004000000 (64.0 MB)
3/11/2020 1:27:47 AM> Partition: devinfo, [00001AB9C000 - 00001AC9C000], size: 000000100000 (1.00 MB)
3/11/2020 1:27:47 AM> Partition: splash, [00001B000000 - 00001BB00000], size: 000000B00000 (11.0 MB)
3/11/2020 1:27:47 AM> Partition: LOGO, [00001BB00000 - 00001DB00000], size: 000002000000 (32.0 MB)
3/11/2020 1:27:47 AM> Partition: DRIVER, [00001DB00000 - 00001FB00000], size: 000002000000 (32.0 MB)
3/11/2020 1:27:47 AM> Partition: cache, [00001FB00000 - 00002FB00000], size: 000010000000 (256. MB)
3/11/2020 1:27:47 AM> Partition: misc, [00002FB00000 - 00002FC00000], size: 000000100000 (1.00 MB)
3/11/2020 1:27:47 AM> Partition: keystore, [00002FC00000 - 00002FC80000], size: 000000080000 (512. KB)
3/11/2020 1:27:47 AM> Partition: config, [00002FC80000 - 00002FC88000], size: 000000008000 (32.0 KB)
3/11/2020 1:27:47 AM> Partition: oem, [00002FC88000 - 00002FD88000], size: 000000100000 (1.00 MB)
3/11/2020 1:27:47 AM> Partition: limits, [000030000000 - 000030008000], size: 000000008000 (32.0 KB)
3/11/2020 1:27:47 AM> Partition: mota, [000030800000 - 000030880000], size: 000000080000 (512. KB)
3/11/2020 1:27:47 AM> Partition: dip, [000030880000 - 000030980000], size: 000000100000 (1.00 MB)
3/11/2020 1:27:47 AM> Partition: mdtp, [000030980000 - 000032980000], size: 000002000000 (32.0 MB)
3/11/2020 1:27:47 AM> Partition: syscfg, [000032980000 - 000032A00000], size: 000000080000 (512. KB)
3/11/2020 1:27:47 AM> Partition: mcfg, [000032A00000 - 000032E00000], size: 000000400000 (4.00 MB)
3/11/2020 1:27:47 AM> Partition: lksecapp, [000033000000 - 000033020000], size: 000000020000 (128. KB)
3/11/2020 1:27:47 AM> Partition: cmnlib, [000033020000 - 000033120000], size: 000000100000 (1.00 MB)
3/11/2020 1:27:47 AM> Partition: cmnlib64, [000033120000 - 000033220000], size: 000000100000 (1.00 MB)
3/11/2020 1:27:47 AM> Partition: keymaster, [000033220000 - 000033320000], size: 000000100000 (1.00 MB)
3/11/2020 1:27:47 AM> Partition: lksecappbak, [000033320000 - 000033340000], size: 000000020000 (128. KB)
3/11/2020 1:27:47 AM> Partition: cmnlibbak, [000033340000 - 000033440000], size: 000000100000 (1.00 MB)
3/11/2020 1:27:47 AM> Partition: cmnlib64bak, [000033440000 - 000033540000], size: 000000100000 (1.00 MB)
3/11/2020 1:27:47 AM> Partition: keymasterbak, [000033540000 - 000033640000], size: 000000100000 (1.00 MB)
3/11/2020 1:27:47 AM> Partition: apdp, [000033800000 - 000033840000], size: 000000040000 (256. KB)
3/11/2020 1:27:47 AM> Partition: msadp, [000033840000 - 000033880000], size: 000000040000 (256. KB)
3/11/2020 1:27:47 AM> Partition: dpo, [000033880000 - 000033882000], size: 000000002000 (8.00 KB)
3/11/2020 1:27:47 AM> Partition: logdump, [000033882000 - 000037882000], size: 000004000000 (64.0 MB)
3/11/2020 1:27:47 AM> Partition: vm-kystore, [000037882000 - 000037982000], size: 000000100000 (1.00 MB)
3/11/2020 1:27:47 AM> Partition: vm-data, [000037982000 - 000038382000], size: 000000A00000 (10.0 MB)
3/11/2020 1:27:47 AM> Partition: hyp, [000038800000 - 000039000000], size: 000000800000 (8.00 MB)
3/11/2020 1:27:47 AM> Partition: vm-system, [000039000000 - 00003D000000], size: 000004000000 (64.0 MB)
3/11/2020 1:27:47 AM> Partition: vm-linux, [00003D000000 - 00003F000000], size: 000002000000 (32.0 MB)
3/11/2020 1:27:47 AM> Partition: system, [00003F000000 - 000115900000], size: 0000D6900000 (3.35 GB)
3/11/2020 1:27:47 AM> Partition: vendor, [000115900000 - 000157860000], size: 000041F60000 (1.03 GB)
3/11/2020 1:27:47 AM> Partition: userdata, [000158000000 - 0003A3DFBE00], size: 00024BDFBE00 (9.19 GB)
3/11/2020 1:27:47 AM> GPT header successfully parsed


(E) Now You need to flash this version of firmware, CPH1803EX_11_A.17_190323_102b469c


Go To Unpack OFP File........

(F) Go To Operation: Write by vendor (Qualcomm/HiSilicon/Omap)


Code:

Creating GPT-partitioninig
Writing PrimaryGPT at address: 000000000000
Writing BackupGPT at address: 0003A3DFBE00
GPT-partitioning done

Partition name: oppodycnvbk
Filename: dynamic_nvbk.bin , Offset: 000000005000 , filesize: 10485760 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 958.73 KB/s
Partition name: oppostanvbk
Filename: static_nvbk.bin , Offset: 000000A05000 , filesize: 10485760 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 1045.91 KB/s
Partition name: persist
Filename: persist.img , Offset: 000001705000 , filesize: 5132700 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Sparse image found v.1.0  Total chunks: 32
Done writing partition. Write speed: 999.65 KB/s
Partition name: opporeserve1
Filename: emmc_fw.bin , Offset: 000003705000 , filesize: 4194304 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 1020.78 KB/s
Partition name: opporeserve2
Filename: opporeserve2.img , Offset: 000003F05000 , filesize: 5300372 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Sparse image found v.1.0  Total chunks: 10
Done writing partition. Write speed: 1029.77 KB/s
Partition name: sbl1
Filename: sbl1.mbn , Offset: 000008308000 , filesize: 452656 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 786.53 KB/s
Partition name: rpm
Filename: rpm.mbn , Offset: 000008388000 , filesize: 174884 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 906.38 KB/s
Partition name: tz
Filename: tz.mbn , Offset: 000008408000 , filesize: 1535872 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 1033.56 KB/s
Partition name: devcfg
Filename: devcfg.mbn , Offset: 000008608000 , filesize: 40220 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 647.89 KB/s
Partition name: sbl1bak
Filename: sbl1.mbn , Offset: 000008648000 , filesize: 452656 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 1009.25 KB/s
Partition name: rpmbak
Filename: rpm.mbn , Offset: 0000086C8000 , filesize: 174884 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 916.57 KB/s
Partition name: tzbak
Filename: tz.mbn , Offset: 000008748000 , filesize: 1535872 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 1034.03 KB/s
Partition name: devcfgbak
Filename: devcfg.mbn , Offset: 000008948000 , filesize: 40220 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 704.44 KB/s
Partition name: dsp
Filename: adspso.bin , Offset: 000008988000 , filesize: 16777216 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 1030.94 KB/s
Partition name: aboot
Filename: emmc_appsboot.mbn , Offset: 00000A18C000 , filesize: 738876 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 1008.16 KB/s
Partition name: abootbak
Filename: emmc_appsboot.mbn , Offset: 00000A28C000 , filesize: 738876 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 1030.65 KB/s
Partition name: modem
Filename: NON-HLOS.bin , Offset: 00000A38C000 , filesize: 134217728 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 1043.81 KB/s
Partition name: dtbo
Filename: dtbo.img , Offset: 00001238C000 , filesize: 8388608 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 1036.50 KB/s
Partition name: vbmeta
Filename: vbmeta.img , Offset: 000012B8C000 , filesize: 4096 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 540.85 KB/s
Partition name: boot
Filename: boot.img , Offset: 000012B9C000 , filesize: 67108864 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 1041.21 KB/s
Partition name: recovery
Filename: recovery.img , Offset: 000016B9C000 , filesize: 67108864 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 1045.91 KB/s
Partition name: LOGO
Filename: logo.bin , Offset: 00001BB00000 , filesize: 878080 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 969.18 KB/s
Partition name: DRIVER
Filename: DRIVER.ISO , Offset: 00001DB00000 , filesize: 23795712 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 1053.62 KB/s
Partition name: cache
Filename: cache.img , Offset: 00001FB00000 , filesize: 6398160 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Sparse image found v.1.0  Total chunks: 15
Done writing partition. Write speed: 1011.17 KB/s
Partition name: mdtp
Filename: mdtp.img , Offset: 000030980000 , filesize: 17808306 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 1033.31 KB/s
Partition name: lksecapp
Filename: lksecapp.mbn , Offset: 000033000000 , filesize: 57352 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 324.95 KB/s
Partition name: cmnlib
Filename: cmnlib_30.mbn , Offset: 000033020000 , filesize: 213856 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 835.81 KB/s
Partition name: cmnlib64
Filename: cmnlib64_30.mbn , Offset: 000033120000 , filesize: 269088 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 862.58 KB/s
Partition name: keymaster
Filename: keymaster64.mbn , Offset: 000033220000 , filesize: 271480 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 869.37 KB/s
Partition name: lksecappbak
Filename: lksecapp.mbn , Offset: 000033320000 , filesize: 57352 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 921.66 KB/s
Partition name: cmnlibbak
Filename: cmnlib_30.mbn , Offset: 000033340000 , filesize: 213856 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 964.23 KB/s
Partition name: cmnlib64bak
Filename: cmnlib64_30.mbn , Offset: 000033440000 , filesize: 269088 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 934.60 KB/s
Partition name: keymasterbak
Filename: keymaster64.mbn , Offset: 000033540000 , filesize: 271480 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 917.39 KB/s
Partition name: apdp
Filename: dpAP.mbn , Offset: 000033800000 , filesize: 13248 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 104.98 KB/s
Partition name: system
Filename: system.img , Offset: 00003F000000 , filesize: 3208174868 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Sparse image found v.1.0  Total chunks: 4714
Done writing partition. Write speed: 1021.47 KB/s
Partition name: vendor
Filename: vendor.img , Offset: 000115900000 , filesize: 978552928 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Sparse image found v.1.0  Total chunks: 2907
Done writing partition. Write speed: 1022.84 KB/s
Partition name: userdata
Filename: userdata.img , Offset: 000158000000 , filesize: 3422620248 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Sparse image found v.1.0  Total chunks: 901
Done writing partition. Write speed: 1041.68 KB/s

Operation: Writing BootConfig ...
Reg: 179  Value: 0x08
Reg: 177  Value: 0x00
Reg: 162  Value: 0x01
Done

All done  time: [02:21:48:720]

Setting interface to EasyJtag2/ISP_HiPower
Setting bus width to 1 Bit
HiPower mode is ON
Setting frequence to 9 MHz
CMD Pullup Level: 2106 mV
CMD Active Level: 2749 mV
EMMC Device Information :
EMMC CID: 150100514536334D4203ADCF07F035FB
EMMC CSD: D02701320F5903FFF6DBFFEF8E40400D
EMMC Manufacture : SAMSUNG , EMMC NAME: QE63MB , HEX: 514536334D42 , S/N: ADCF07F0 , rev. 0x03
EMMC Manufacture ID: 0x15 , OEM ID: 0x00 , Device Type: BGA (Discrete embedded) , Date: 3/2018
  EMMC ROM 1 (Main User Data) Capacity: 14910 MB (0003A3E00000)
  EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
  EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000) Counter: 69475 , Response: Not Clean
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.8 (MMC 5.1)
Boot configuration [PARTITION_CONFIG]: 0x08 , Boot from: ROM2 (Boot partition 1)
Boot Bus Config: 0x00 , width 1bit
H/W Reset Function [RST_N_FUNCTION]: 0x01, RST_n signal is permanently enabled
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: QE63MB_ADCF07F0_20200312_001643.extcsd
EMMC Init completed.

Scanning soft partitions
Code:

GPT header is found and is valid
Partition: oppodycnvbk, [000000005000 - 000000A05000], size: 000000A00000 (10.0 MB)
Partition: oppostanvbk, [000000A05000 - 000001405000], size: 000000A00000 (10.0 MB)
Partition: modemst1, [000001405000 - 000001585000], size: 000000180000 (1.50 MB)
Partition: modemst2, [000001585000 - 000001705000], size: 000000180000 (1.50 MB)
Partition: persist, [000001705000 - 000003705000], size: 000002000000 (32.0 MB)
Partition: opporeserve1, [000003705000 - 000003F05000], size: 000000800000 (8.00 MB)
Partition: opporeserve2, [000003F05000 - 000007F05000], size: 000004000000 (64.0 MB)
Partition: reserve_exp1, [000007F05000 - 000008105000], size: 000000200000 (2.00 MB)
Partition: reserve_exp2, [000008105000 - 000008305000], size: 000000200000 (2.00 MB)
Partition: fsc, [000008305000 - 000008305400], size: 000000000400 (1.00 KB)
Partition: ssd, [000008306000 - 000008308000], size: 000000002000 (8.00 KB)
Partition: sbl1, [000008308000 - 000008388000], size: 000000080000 (512. KB)
Partition: rpm, [000008388000 - 000008408000], size: 000000080000 (512. KB)
Partition: tz, [000008408000 - 000008608000], size: 000000200000 (2.00 MB)
Partition: devcfg, [000008608000 - 000008648000], size: 000000040000 (256. KB)
Partition: sbl1bak, [000008648000 - 0000086C8000], size: 000000080000 (512. KB)
Partition: rpmbak, [0000086C8000 - 000008748000], size: 000000080000 (512. KB)
Partition: tzbak, [000008748000 - 000008948000], size: 000000200000 (2.00 MB)
Partition: devcfgbak, [000008948000 - 000008988000], size: 000000040000 (256. KB)
Partition: dsp, [000008988000 - 000009988000], size: 000001000000 (16.0 MB)
Partition: DDR, [00000A000000 - 00000A008000], size: 000000008000 (32.0 KB)
Partition: fsg, [00000A008000 - 00000A188000], size: 000000180000 (1.50 MB)
Partition: sec, [00000A188000 - 00000A18C000], size: 000000004000 (16.0 KB)
Partition: aboot, [00000A18C000 - 00000A28C000], size: 000000100000 (1.00 MB)
Partition: abootbak, [00000A28C000 - 00000A38C000], size: 000000100000 (1.00 MB)
Partition: modem, [00000A38C000 - 00001238C000], size: 000008000000 (128. MB)
Partition: dtbo, [00001238C000 - 000012B8C000], size: 000000800000 (8.00 MB)
Partition: vbmeta, [000012B8C000 - 000012B9C000], size: 000000010000 (64.0 KB)
Partition: boot, [000012B9C000 - 000016B9C000], size: 000004000000 (64.0 MB)
Partition: recovery, [000016B9C000 - 00001AB9C000], size: 000004000000 (64.0 MB)
Partition: devinfo, [00001AB9C000 - 00001AC9C000], size: 000000100000 (1.00 MB)
Partition: splash, [00001B000000 - 00001BB00000], size: 000000B00000 (11.0 MB)
Partition: LOGO, [00001BB00000 - 00001DB00000], size: 000002000000 (32.0 MB)
Partition: DRIVER, [00001DB00000 - 00001FB00000], size: 000002000000 (32.0 MB)
Partition: cache, [00001FB00000 - 00002FB00000], size: 000010000000 (256. MB)
Partition: misc, [00002FB00000 - 00002FC00000], size: 000000100000 (1.00 MB)
Partition: keystore, [00002FC00000 - 00002FC80000], size: 000000080000 (512. KB)
Partition: config, [00002FC80000 - 00002FC88000], size: 000000008000 (32.0 KB)
Partition: oem, [00002FC88000 - 00002FD88000], size: 000000100000 (1.00 MB)
Partition: limits, [000030000000 - 000030008000], size: 000000008000 (32.0 KB)
Partition: mota, [000030800000 - 000030880000], size: 000000080000 (512. KB)
Partition: dip, [000030880000 - 000030980000], size: 000000100000 (1.00 MB)
Partition: mdtp, [000030980000 - 000032980000], size: 000002000000 (32.0 MB)
Partition: syscfg, [000032980000 - 000032A00000], size: 000000080000 (512. KB)
Partition: mcfg, [000032A00000 - 000032E00000], size: 000000400000 (4.00 MB)
Partition: lksecapp, [000033000000 - 000033020000], size: 000000020000 (128. KB)
Partition: cmnlib, [000033020000 - 000033120000], size: 000000100000 (1.00 MB)
Partition: cmnlib64, [000033120000 - 000033220000], size: 000000100000 (1.00 MB)
Partition: keymaster, [000033220000 - 000033320000], size: 000000100000 (1.00 MB)
Partition: lksecappbak, [000033320000 - 000033340000], size: 000000020000 (128. KB)
Partition: cmnlibbak, [000033340000 - 000033440000], size: 000000100000 (1.00 MB)
Partition: cmnlib64bak, [000033440000 - 000033540000], size: 000000100000 (1.00 MB)
Partition: keymasterbak, [000033540000 - 000033640000], size: 000000100000 (1.00 MB)
Partition: apdp, [000033800000 - 000033840000], size: 000000040000 (256. KB)
Partition: msadp, [000033840000 - 000033880000], size: 000000040000 (256. KB)
Partition: dpo, [000033880000 - 000033882000], size: 000000002000 (8.00 KB)
Partition: logdump, [000033882000 - 000037882000], size: 000004000000 (64.0 MB)
Partition: vm-kystore, [000037882000 - 000037982000], size: 000000100000 (1.00 MB)
Partition: vm-data, [000037982000 - 000038382000], size: 000000A00000 (10.0 MB)
Partition: hyp, [000038800000 - 000039000000], size: 000000800000 (8.00 MB)
Partition: vm-system, [000039000000 - 00003D000000], size: 000004000000 (64.0 MB)
Partition: vm-linux, [00003D000000 - 00003F000000], size: 000002000000 (32.0 MB)
Partition: system, [00003F000000 - 000115900000], size: 0000D6900000 (3.35 GB)
Partition: vendor, [000115900000 - 000157860000], size: 000041F60000 (1.03 GB)
Partition: userdata, [000158000000 - 0003A3DFBE00], size: 00024BDFBE00 (9.19 GB)
GPT header successfully parsed

Get firmware version

Manufacturer = OPPO
CPU Abi = arm64-v8a
Android release = 8.1.0
Brand = OPPO
Device = CPH1803
Model = CPH1803
Firmware version = CPH1803EX_11_A.17
Firmware date = Sat Mar 23 21:42:03 CST 2019



Step 1 Has been Successfully Completed ;)


https://i.ibb.co/68tFNjV/1.png
https://i.ibb.co/BP6wtLK/2.png


================================================== =======================

================================================== =======================


Step 2 :-

(E) Unfortunately if You cannot successfully revive your phone. if you have already backup your security area / partitions data.

(F) Go to eMMC General / Erase eMMC Wait until Finis.......

(G) Just you complete the Step (1) section (D) all job complete.

(H) Go to eMMC config / Boot_Partition_EN 0x7 : User area enabled for boot / set partitions config 0x38

(H) Do you complete from the (Step 1) section (C) backup data write by vendor.

Hopefully your problem willbe solved. ;)

Full_Dump_With User Area_OPPO A3S CPH1803EX_11_A.17_Samsung eMMC _06_03_2020_16_08_12_QE63MB_fsg_part

Oppo A3s Repair Tools & QCN

Only For JTAG expert users if you want you can flash the User area full Dump throw partitions by partitions.

The greatest mind contributing to all the Dump File all the credit goes to him solusi hp

Really This job was my long-range work. ;) :)

Best regard for all of Oppo Technician

kothamamun 03-04-2020 08:52

great work brother best of luck.

.::THE ROCK::. 03-04-2020 09:06

NICE SHER BRO,


BUT CONFUSED.....



JTAG PLUS NOT ACTIVATED,:)


EasyJtag Suite Classic ver.: 3.6.2.0 / wxWidgets 3.1.3-W-U started.
OS ver.: Windows 7 (build 7600). Admin rights OK
Autorun Agent ver:1.0.0.0
Crash Reporting ver:1.4.0.3
EasyJTAG SPI Plugin ver:1.1.1.11
Android ADB API ver:2.0.0.0
FTDI API ver:3.2.4.0
LibUSB API ver:1.2.6.0
Visual C++ Runtime ver:10.0.30319.1
Setting box Pinout ...

Box Drivers version: 3.0.1.0, are OK
Z3X Card Serial : AA27-78BA , ver: 22
Z3X Card Activation [JTAGPLUS] : NOT ACTIVATED
Z3X Card Activation [LG] : NOT ACTIVATED
Z3X Card Activation [SAMS] : NOT ACTIVATED
Z3X Card Activation [JTAG] : ACTIVATED



JTAG PLUS WORKED :confused:



eMMC_tool Suite ver. 1.6.2.0 (release date: 30.06.2019)
Microsoft Windows 7 (32 bit) build 7600 (6.1.7600.16385)

Looking for EasyJTAG box...
EasyJTAG API ver. 3307
EasyJTAG Box Serial = 1717020DE19BFA4A
Card Serial = AA2778BA
EasyJTAG Box Firmware = 1.63

GOOD SIR

...:::::NP™:::::... 03-04-2020 09:23

No need JTAG Plus for this category of hard work.

Just you need perseverance [03+ Hour] time: [03:17:30:071] my PC Config is Core i5 with 4GB RAM.

Amazing thing it's Fast Easy JTAG Z3X team 1'st Generation JTAG when it was released by GPG hardware. ;)

But it's reality z3x team is perfectly, acculturating, combined for old & new hardware coding .

http://easy-jtag.com/wp-content/uplo...08/GPG_SET.jpg

http://easy-jtag.com/easyjtag-in-plastic-case/

kothamamun 03-04-2020 09:24

Quote:

Originally Posted by .::THE ROCK::. (Post 14034562)
NICE SHER BRO,


BUT CONFUSED.....



JTAG PLUS NOT ACTIVATED,:)


EasyJtag Suite Classic ver.: 3.6.2.0 / wxWidgets 3.1.3-W-U started.
OS ver.: Windows 7 (build 7600). Admin rights OK
Autorun Agent ver:1.0.0.0
Crash Reporting ver:1.4.0.3
EasyJTAG SPI Plugin ver:1.1.1.11
Android ADB API ver:2.0.0.0
FTDI API ver:3.2.4.0
LibUSB API ver:1.2.6.0
Visual C++ Runtime ver:10.0.30319.1
Setting box Pinout ...

Box Drivers version: 3.0.1.0, are OK
Z3X Card Serial : AA27-78BA , ver: 22
Z3X Card Activation [JTAGPLUS] : NOT ACTIVATED
Z3X Card Activation [LG] : NOT ACTIVATED
Z3X Card Activation [SAMS] : NOT ACTIVATED
Z3X Card Activation [JTAG] : ACTIVATED



JTAG PLUS WORKED :confused:



eMMC_tool Suite ver. 1.6.2.0 (release date: 30.06.2019)
Microsoft Windows 7 (32 bit) build 7600 (6.1.7600.16385)

Looking for EasyJTAG box...
EasyJTAG API ver. 3307
EasyJTAG Box Serial = 1717020DE19BFA4A
Card Serial = AA2778BA
EasyJTAG Box Firmware = 1.63

GOOD SIR

only jtag is working very fine to unlock and dead recover.
little slow to writing speed.

Meraj Ahmad 04-03-2020 10:27

Great bro....Thanks;);)

lillzbb 04-08-2020 15:58

Great work bro,very nice

otiblo 04-09-2020 19:52

oppo a57
 
hi could you please help me on how i can flash oppo a57 dead and how to remove password on screen of oppo A1K. thak you

...:::::NP™:::::... 04-09-2020 20:19

@ otiblo

You can get idea about A57 flashing via Easy Jtag http://forum.gsmhosting.com/vbb/13505969-post10.html also flow my 1'st post, Above the same way.

Download your phone correct model factory firmware, then extract with Easy jtag then you can flash via ISP connection.

Your another phone A1K is MTK Based phone.

khaleddz19 05-30-2020 14:45

great work bro
can you help me to revive dead cph1823
with easy jtag

talebamine8 05-31-2020 01:30

thank you for this useful post is the procedure same with Oppo a7 dead after password reset?

...:::::NP™:::::... 05-31-2020 12:21

@ khaleddz19

&

talebamine8




Both of you need tested dump file for theses of model phones. before any operation must created security area back by your self.

Also you can flow my procedure, try with your correct model Dump & firmware.


Best of luck

pintu_das 06-09-2020 18:27

for mtk you need also backup NVRAM and "protect _xxx" partition



(B) How to backup security area / partitions. Read by vendor ?

Answer:-

Run ''EasyJTAG Plus'' set voltage manually which voltage sweet-able for your eMMC detected also set the frequency 1 mhz + Bus 1 bit.

Go to Read soft partitions then Check ''eMMC / UFS'' if you get all partitions is okay only your phone dose not run or EDL mode detected by 'PC" device manager.

No problem ! don't be upset !

Go to Read by vendor operation ''TAB" there are already all partitions are visible.

(C) Pay attention, You have need to be create Below the partitions backup very carefully.

*) config

*) fsg

*) sec

*) modem

*) modemst1

*) modemst2

*) oppodycnvbk

*) opporeserve2

*) oppostanvbk

*) Persist

https://i.ibb.co/pd38BVf/index.png

mhayketech 06-10-2020 17:08

This is a really good and informative solution, thank you for helping other make their job well done...

GSMSHOP1 06-10-2020 17:47

Hello Mr

any help for slove this problm im step by step if you possible

THANKS MAN

HiPower mode is ON
Setting frequence to 14 MHz
CMD Pullup Level: 2010 mV
CMD Active Level: 2619 mV
EMMC Device Information :
EMMC CID: 90014A484147346132A5C3375C748594
EMMC CSD: D02701328F5903FFFFFFFFE78A400016
EMMC Manufacture : SKHYNIX , EMMC NAME: HAG4a2 , HEX: 484147346132 , S/N: C3375C74 , rev. 0xA5
EMMC Manufacture ID: 0x90 , OEM ID: 0x4A , Device Type: BGA (Discrete embedded) , Date: 8/2018
EMMC ROM 1 (Main User Data) Capacity: 15028 MB (0003AB400000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000) Counter: 1237 , Response: Not Clean
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.8 (MMC 5.1)
Boot configuration [PARTITION_CONFIG]: 0x38 , Boot from: ROM1 (Main User Area)
Boot Bus Config: 0x00 , width 1bit
H/W Reset Function [RST_N_FUNCTION]: 0x01, RST_n signal is permanently enabled
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: HAG4a2_C3375C74_20200610_163554.extcsd
EMMC Init completed.

Get firmware version
Error reading at address: 000000000000 , error: -1, CMD Timeout Error ... Retry #1
Error reading at address: 000000000000 , error: -1, CMD Timeout Error ... Retry #2
Error reading at address: 000000000000 , error: -1, CMD Timeout Error ... Retry #3
Error reading at address: 000000000000 , error: -1, CMD Timeout Error ... Retry #4
Error reading at address: 000000000000 , error: -1, CMD Timeout Error ... Retry #5
Too many errors. Reading has been stopped




.................................................. .................................................. ........................
ERASER EMMC

HiPower mode is ON
Setting frequence to 14 MHz
CMD Pullup Level: 2000 mV
CMD Active Level: 2619 mV
EMMC Device Information :
EMMC CID: 90014A484147346132A5C3375C748594
EMMC CSD: D02701328F5903FFFFFFFFE78A400016
EMMC Manufacture : SKHYNIX , EMMC NAME: HAG4a2 , HEX: 484147346132 , S/N: C3375C74 , rev. 0xA5
EMMC Manufacture ID: 0x90 , OEM ID: 0x4A , Device Type: BGA (Discrete embedded) , Date: 8/2018
EMMC ROM 1 (Main User Data) Capacity: 15028 MB (0003AB400000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000) Counter: 1237 , Response: Not Clean
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.8 (MMC 5.1)
Boot configuration [PARTITION_CONFIG]: 0x38 , Boot from: ROM1 (Main User Area)
Boot Bus Config: 0x00 , width 1bit
H/W Reset Function [RST_N_FUNCTION]: 0x01, RST_n signal is permanently enabled
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: HAG4a2_C3375C74_20200610_165209.extcsd
EMMC Init completed.

Operation: Erasing eMMC...

Erasing for: ROM1 , start: 0x000000000000 , size: 0x000000020000
eMMC switching to ROM1
Erasing partition...
Error erasing at address: 000000000000 , error: -1, CMD Timeout Error ... Retry #1
Error erasing at address: 000000000000 , error: -1, CMD Timeout Error ... Retry #2
Error erasing at address: 000000000000 , error: -1, CMD Timeout Error ... Retry #3
Too many errors. Erasing has been stopped

...:::::NP™:::::... 06-11-2020 12:59

Hi,

High speed not sweet able or Per hubs for your required job.

You set the high speed mode For erasing purpose, just set the low frequency as per as my posting image 9Mhz Bus1Bit.

GSMSHOP1 06-14-2020 14:53

hello

ihave oppo a3s problme the current image boot recovery have

if just flash recovery and boot with easy jtag i cant work to enter in recovery mode,????????????

layder 06-15-2020 00:35

Quote:

Originally Posted by GSMSHOP1 (Post 14110068)
Hello Mr

any help for slove this problm im step by step if you possible

THANKS MAN



Operation: Erasing eMMC...

Erasing for: ROM1 , start: 0x000000000000 , size: 0x000000020000
eMMC switching to ROM1
Erasing partition...
Error erasing at address: 000000000000 , error: -1, CMD Timeout Error ... Retry #1
Error erasing at address: 000000000000 , error: -1, CMD Timeout Error ... Retry #2
Error erasing at address: 000000000000 , error: -1, CMD Timeout Error ... Retry #3
Too many errors. Erasing has been stopped

https://forum.gsmhosting.com/vbb/f67...ution-2585863/

zack winstone 06-25-2020 05:32

I can not see the rowprogram0 when i backup

solusi hp 06-25-2020 05:41

Quote:

Originally Posted by zack winstone (Post 14124023)
I can not see the rowprogram0 when i backup


no need rawprogramm0 for backup just backup necessary partition like post 1

sed_1982 07-14-2020 06:39

Help
can't download on dump it says no mirror on the link given,, and of course on mega quota exceeeded

br.,

...:::::NP™:::::... 07-14-2020 07:46

## Mirror Download Link For Oppo A3s Dump & Security Data


Dump_OPPO_A3S_CPH1803EX_11_A.17_Samsung_eMMC__QE63 MB_06_03_2020_16_08_12

Download ====> Link 1 !! Link 2 !! Link 3







Dump_OPPO_A3S_CPH1803EX_11_A.17_Samsung_eMMC_oppod ycnvbk_+_oppostanvbk_+_modemst1_+_modemst2_+_fsg_+ _sec_+_modem.7z

Download === Link 1 !! Link 2 !! Link 3

sed_1982 07-16-2020 00:01

after full flash no network

imei null, something i missed?

no baseband. Imei-Null

layder 07-16-2020 09:23

Quote:

Originally Posted by sed_1982 (Post 14148486)
after full flash no network

imei null, something i missed?

no baseband. Imei-Null

Instruction about backup and restore security is posted at first message of this topic

sed_1982 07-17-2020 04:51

Quote:

Originally Posted by layder (Post 14148887)
Instruction about backup and restore security is posted at first message of this topic

sorry sir but this phone come from different repair center..Thats why im looking for nvdata or a data that can revive or restore the nvm data.

carter_ 07-17-2020 05:52

great work brother thaks for sharing..

jamohaki 08-02-2020 13:08

i have oppo A3s cph1803 with detected in edl i followed the all procedures but still stuck in edl i checked in hardware everything seems to be ok anyway to revive this phone may i missed something ?

solusi hp 08-03-2020 07:01

Quote:

Originally Posted by jamohaki (Post 14168301)
i have oppo A3s cph1803 with detected in edl i followed the all procedures but still stuck in edl i checked in hardware everything seems to be ok anyway to revive this phone may i missed something ?

show your log please

jamohaki 08-03-2020 12:16

this exactly what i did:

Quote:

backup security area / partitions:
eMMC_tool Suite ver. 1.6.3.0 (release date: 23.06.2020)
Microsoft Windows 7 (32 bit) build 7601 (6.1.7600.16385)

Looking for EasyJTAG box...
EasyJTAG API ver. 3401
EasyJTAG Box Serial = 1616120653F9FBE6
Card Serial = AA14969B
EasyJTAG Box Firmware = 1.6300

Changelog:

23.06.2020 (ver 1.6.3.0)
Fix: Bugs that have been found through your crash report

Setting frequence to 21 MHz
CMD Pullup Level: 1990 mV
CMD Active Level: 2062 mV
EMMC Device Information :
EMMC CID: 90014A484147346132A5C1E25D7BC5D2
EMMC CSD: D02701328F5903FFFFFFFFE78A400016
EMMC Manufacture : SKHYNIX , EMMC NAME: HAG4a2 , HEX: 484147346132 , S/N: C1E25D7B , rev. 0xA5
EMMC ROM 1 (Main User Data) Capacity: 15028 MB (0003AB400000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000) Counter: 34316 , Response: Not Clean
Extended CSD Information :
Extended CSD rev: 1.8 (MMC 5.1)
Boot configuration [179] / Boot Bus Config [177] / H/W Reset Function [162]: 0x38 / 0x00 / 0x01
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Backup saved: HAG4a2_C1E25D7B_20200801_084527.extcsd
EMMC Init completed.

Get firmware version

Manufacturer = OPPO
CPU Abi = arm64-v8a
Android release = 8.1.0
Security Patch = 2020-07-05
Brand = OPPO
Device = CPH1803
Model = CPH1803
Firmware version = CPH1803EX_11_A.29
Firmware date = Fri Jul 10 01:27:23 CST 2020

Setting frequence to 21 MHz
CMD Pullup Level: 1804 mV
CMD Active Level: 2062 mV
EMMC Device Information :
EMMC CID: 90014A484147346132A5C1E25D7BC5D2
EMMC CSD: D02701328F5903FFFFFFFFE78A400016
EMMC Manufacture : SKHYNIX , EMMC NAME: HAG4a2 , HEX: 484147346132 , S/N: C1E25D7B , rev. 0xA5
EMMC ROM 1 (Main User Data) Capacity: 15028 MB (0003AB400000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000) Counter: 34316 , Response: Not Clean
Extended CSD Information :
Extended CSD rev: 1.8 (MMC 5.1)
Boot configuration [179] / Boot Bus Config [177] / H/W Reset Function [162]: 0x38 / 0x00 / 0x01
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Backup saved: HAG4a2_C1E25D7B_20200801_084639.extcsd
EMMC Init completed.

Scanning soft partitions
GPT header is found and is valid
Partition: oppodycnvbk, [000000005000 - 000000A05000], size: 000000A00000 (10.0 MB)
Partition: oppostanvbk, [000000A05000 - 000001405000], size: 000000A00000 (10.0 MB)
Partition: modemst1, [000001405000 - 000001585000], size: 000000180000 (1.50 MB)
Partition: modemst2, [000001585000 - 000001705000], size: 000000180000 (1.50 MB)
Partition: persist, [000001705000 - 000003705000], size: 000002000000 (32.0 MB)
Partition: opporeserve1, [000003705000 - 000003F05000], size: 000000800000 (8.00 MB)
Partition: opporeserve2, [000003F05000 - 000007F05000], size: 000004000000 (64.0 MB)
Partition: reserve_exp1, [000007F05000 - 000008105000], size: 000000200000 (2.00 MB)
Partition: reserve_exp2, [000008105000 - 000008305000], size: 000000200000 (2.00 MB)
Partition: fsc, [000008305000 - 000008305400], size: 000000000400 (1.00 KB)
Partition: ssd, [000008306000 - 000008308000], size: 000000002000 (8.00 KB)
Partition: sbl1, [000008308000 - 000008388000], size: 000000080000 (512. KB)
Partition: rpm, [000008388000 - 000008408000], size: 000000080000 (512. KB)
Partition: tz, [000008408000 - 000008608000], size: 000000200000 (2.00 MB)
Partition: devcfg, [000008608000 - 000008648000], size: 000000040000 (256. KB)
Partition: sbl1bak, [000008648000 - 0000086C8000], size: 000000080000 (512. KB)
Partition: rpmbak, [0000086C8000 - 000008748000], size: 000000080000 (512. KB)
Partition: tzbak, [000008748000 - 000008948000], size: 000000200000 (2.00 MB)
Partition: devcfgbak, [000008948000 - 000008988000], size: 000000040000 (256. KB)
Partition: dsp, [000008988000 - 000009988000], size: 000001000000 (16.0 MB)
Partition: DDR, [00000A000000 - 00000A008000], size: 000000008000 (32.0 KB)
Partition: fsg, [00000A008000 - 00000A188000], size: 000000180000 (1.50 MB)
Partition: sec, [00000A188000 - 00000A18C000], size: 000000004000 (16.0 KB)
Partition: aboot, [00000A18C000 - 00000A28C000], size: 000000100000 (1.00 MB)
Partition: abootbak, [00000A28C000 - 00000A38C000], size: 000000100000 (1.00 MB)
Partition: modem, [00000A38C000 - 00001238C000], size: 000008000000 (128. MB)
Partition: dtbo, [00001238C000 - 000012B8C000], size: 000000800000 (8.00 MB)
Partition: vbmeta, [000012B8C000 - 000012B9C000], size: 000000010000 (64.0 KB)
Partition: boot, [000012B9C000 - 000016B9C000], size: 000004000000 (64.0 MB)
Partition: recovery, [000016B9C000 - 00001AB9C000], size: 000004000000 (64.0 MB)
Partition: devinfo, [00001AB9C000 - 00001AC9C000], size: 000000100000 (1.00 MB)
Partition: splash, [00001B000000 - 00001BB00000], size: 000000B00000 (11.0 MB)
Partition: LOGO, [00001BB00000 - 00001DB00000], size: 000002000000 (32.0 MB)
Partition: DRIVER, [00001DB00000 - 00001FB00000], size: 000002000000 (32.0 MB)
Partition: cache, [00001FB00000 - 00002FB00000], size: 000010000000 (256. MB)
Partition: misc, [00002FB00000 - 00002FC00000], size: 000000100000 (1.00 MB)
Partition: keystore, [00002FC00000 - 00002FC80000], size: 000000080000 (512. KB)
Partition: config, [00002FC80000 - 00002FC88000], size: 000000008000 (32.0 KB)
Partition: oem, [00002FC88000 - 00002FD88000], size: 000000100000 (1.00 MB)
Partition: limits, [000030000000 - 000030008000], size: 000000008000 (32.0 KB)
Partition: mota, [000030800000 - 000030880000], size: 000000080000 (512. KB)
Partition: dip, [000030880000 - 000030980000], size: 000000100000 (1.00 MB)
Partition: mdtp, [000030980000 - 000032980000], size: 000002000000 (32.0 MB)
Partition: syscfg, [000032980000 - 000032A00000], size: 000000080000 (512. KB)
Partition: mcfg, [000032A00000 - 000032E00000], size: 000000400000 (4.00 MB)
Partition: lksecapp, [000033000000 - 000033020000], size: 000000020000 (128. KB)
Partition: cmnlib, [000033020000 - 000033120000], size: 000000100000 (1.00 MB)
Partition: cmnlib64, [000033120000 - 000033220000], size: 000000100000 (1.00 MB)
Partition: keymaster, [000033220000 - 000033320000], size: 000000100000 (1.00 MB)
Partition: lksecappbak, [000033320000 - 000033340000], size: 000000020000 (128. KB)
Partition: cmnlibbak, [000033340000 - 000033440000], size: 000000100000 (1.00 MB)
Partition: cmnlib64bak, [000033440000 - 000033540000], size: 000000100000 (1.00 MB)
Partition: keymasterbak, [000033540000 - 000033640000], size: 000000100000 (1.00 MB)
Partition: apdp, [000033800000 - 000033840000], size: 000000040000 (256. KB)
Partition: msadp, [000033840000 - 000033880000], size: 000000040000 (256. KB)
Partition: dpo, [000033880000 - 000033882000], size: 000000002000 (8.00 KB)
Partition: logdump, [000033882000 - 000037882000], size: 000004000000 (64.0 MB)
Partition: vm-kystore, [000037882000 - 000037982000], size: 000000100000 (1.00 MB)
Partition: vm-data, [000037982000 - 000038382000], size: 000000A00000 (10.0 MB)
Partition: hyp, [000038800000 - 000039000000], size: 000000800000 (8.00 MB)
Partition: vm-system, [000039000000 - 00003D000000], size: 000004000000 (64.0 MB)
Partition: vm-linux, [00003D000000 - 00003F000000], size: 000002000000 (32.0 MB)
Partition: system, [00003F000000 - 000115900000], size: 0000D6900000 (3.35 GB)
Partition: vendor, [000115900000 - 000157860000], size: 000041F60000 (1.03 GB)
Partition: userdata, [000158000000 - 0003AB3FBE00], size: 0002533FBE00 (9.30 GB)
GPT header successfully parsed

Setting frequence to 21 MHz
CMD Pullup Level: 1856 mV
CMD Active Level: 2021 mV
EMMC Device Information :
EMMC CID: 90014A484147346132A5C1E25D7BC5D2
EMMC CSD: D02701328F5903FFFFFFFFE78A400016
EMMC Manufacture : SKHYNIX , EMMC NAME: HAG4a2 , HEX: 484147346132 , S/N: C1E25D7B , rev. 0xA5
EMMC ROM 1 (Main User Data) Capacity: 15028 MB (0003AB400000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000) Counter: 34316 , Response: Not Clean
Extended CSD Information :
Extended CSD rev: 1.8 (MMC 5.1)
Boot configuration [179] / Boot Bus Config [177] / H/W Reset Function [162]: 0x38 / 0x00 / 0x01
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Backup saved: HAG4a2_C1E25D7B_20200801_084924.extcsd
EMMC Init completed.

Operation: Find table from emmc

Vendor: Qualcomm
Searching GPT ...
GPT header is found and is valid
Checking for ROM2 ...
ROM2 is blank
Checking for ROM3 ...
ROM3 is not blank
GPT header successfully parsed

Operation: Read by vendor...
Destination dir: C:\Program Files\Z3X\EASYJTAGPLUS\A3S BK\

Setting frequence to 21 MHz
CMD Pullup Level: 1907 mV
CMD Active Level: 2052 mV
EMMC Device Information :
EMMC CID: 90014A484147346132A5C1E25D7BC5D2
EMMC CSD: D02701328F5903FFFFFFFFE78A400016
EMMC Manufacture : SKHYNIX , EMMC NAME: HAG4a2 , HEX: 484147346132 , S/N: C1E25D7B , rev. 0xA5
EMMC ROM 1 (Main User Data) Capacity: 15028 MB (0003AB400000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000) Counter: 34316 , Response: Not Clean
Extended CSD Information :
Extended CSD rev: 1.8 (MMC 5.1)
Boot configuration [179] / Boot Bus Config [177] / H/W Reset Function [162]: 0x38 / 0x00 / 0x01
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Backup saved: HAG4a2_C1E25D7B_20200801_090535.extcsd
EMMC Init completed.

Backup partition: 8xxx_msimage
Address: 000000004400, size: 000000000C00
eMMC switching to ROM1
Reading partition...
Done reading partition. Read speed: 82.53 Kb/s
8xxx image is blank. Skipped

XML-file created successfully

Backup partition: PrimaryGPT
Address: 000000000000, size: 000000004400
GPTHeader is valid

Partition name: oppodycnvbk
Address: 000000005000, size: 000000A00000
eMMC switching to ROM1
Reading partition...
Done reading partition. Read speed: 619.70 Kb/s
Partition name: oppostanvbk
Address: 000000A05000, size: 000000A00000
eMMC switching to ROM1
Reading partition...
Done reading partition. Read speed: 617.96 Kb/s
Partition name: modemst1
Address: 000001405000, size: 000000180000
eMMC switching to ROM1
Reading partition...
Done reading partition. Read speed: 603.13 Kb/s
Partition name: modemst2
Address: 000001585000, size: 000000180000
eMMC switching to ROM1
Reading partition...
Done reading partition. Read speed: 602.15 Kb/s
Partition name: persist
Address: 000001705000, size: 000002000000
eMMC switching to ROM1
Reading partition...
Done reading partition. Read speed: 620.69 Kb/s
Partition name: opporeserve2
Address: 000003F05000, size: 000004000000
eMMC switching to ROM1
Reading partition...
Done reading partition. Read speed: 623.71 Kb/s
Partition name: fsg
Address: 00000A008000, size: 000000180000
eMMC switching to ROM1
Reading partition...
Done reading partition. Read speed: 621.80 Kb/s
Partition name: sec
Address: 00000A188000, size: 000000004000
eMMC switching to ROM1
Reading partition...
Done reading partition. Read speed: 288.48 Kb/s
Partition name: modem
Address: 00000A38C000, size: 000008000000
eMMC switching to ROM1
Reading partition...
Done reading partition. Read speed: 613.82 Kb/s
Partition name: config
Address: 00002FC80000, size: 000000008000
eMMC switching to ROM1
Reading partition...
Done reading partition. Read speed: 413.59 Kb/s

All done time: [00:07:01:684]


write Dump_OPPO A3S CPH1803EX_11_A.17_Samsung eMMC_ QE63MB_06_03_2020_16_08_12.bin :

eMMC_tool Suite ver. 1.6.3.0 (release date: 23.06.2020)
Microsoft Windows 7 (32 bit) build 7601 (6.1.7600.16385)

Looking for EasyJTAG box...
EasyJTAG API ver. 3401
EasyJTAG Box Serial =
Card Serial =
EasyJTAG Box Firmware = 1.6300

Changelog:

23.06.2020 (ver 1.6.3.0)
Fix: Bugs that have been found through your crash report

Setting frequence to 21 MHz
CMD Pullup Level: 1856 mV
CMD Active Level: 2072 mV
EMMC Device Information :
EMMC CID: 90014A484147346132A5C1E25D7BC5D2
EMMC CSD: D02701328F5903FFFFFFFFE78A400016
EMMC Manufacture : SKHYNIX , EMMC NAME: HAG4a2 , HEX: 484147346132 , S/N: C1E25D7B , rev. 0xA5
EMMC ROM 1 (Main User Data) Capacity: 15028 MB (0003AB400000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000) Counter: 34316 , Response: Not Clean
Extended CSD Information :
Extended CSD rev: 1.8 (MMC 5.1)
Boot configuration [179] / Boot Bus Config [177] / H/W Reset Function [162]: 0x38 / 0x00 / 0x01
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Backup saved: HAG4a2_C1E25D7B_20200801_110854.extcsd
EMMC Init completed.

Operation: Writing eMMC...

Writing to: ROM1 , start: 0x000000000000 , size: 0x00000FA00000
Input file: C:\Users\jms\Desktop\TEMP\OPPO A3S CPH1803EX\New folder\Samsung eMMC _06_03_2020_16_08_12.bin
eMMC switching to ROM1
Writing partition...
Done writing partition. Write speed: 480.12 KB/s

All done time: [00:08:53:725]


flash firmware, CPH1803EX_11_A.17_190323_102b469c

Operation: Extract OFP
Filename: CPH1803EX_11_A.17_190323_102b469c.ofp

XML found
Extracting files. Please, wait ...
Extracted 61 files

All done

Setting frequence to 21 MHz
CMD Pullup Level: 1928 mV
CMD Active Level: 2072 mV
EMMC Device Information :
EMMC CID: 90014A484147346132A5C1E25D7BC5D2
EMMC CSD: D02701328F5903FFFFFFFFE78A400016
EMMC Manufacture : SKHYNIX , EMMC NAME: HAG4a2 , HEX: 484147346132 , S/N: C1E25D7B , rev. 0xA5
EMMC ROM 1 (Main User Data) Capacity: 15028 MB (0003AB400000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000) Counter: 34316 , Response: Not Clean
Extended CSD Information :
Extended CSD rev: 1.8 (MMC 5.1)
Boot configuration [179] / Boot Bus Config [177] / H/W Reset Function [162]: 0x38 / 0x00 / 0x01
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Backup saved: HAG4a2_C1E25D7B_20200801_121400.extcsd
EMMC Init completed.

Opening file: rawprogram0.xml

The size of the last section has been updated

Could not open file: C:\Users\jms\Desktop\TEMP\OPPO A3S CPH1803EX\New folder\A3S NEW\userdata.img

Setting frequence to 21 MHz
CMD Pullup Level: 1928 mV
CMD Active Level: 2052 mV
EMMC Device Information :
EMMC CID: 90014A484147346132A5C1E25D7BC5D2
EMMC CSD: D02701328F5903FFFFFFFFE78A400016
EMMC Manufacture : SKHYNIX , EMMC NAME: HAG4a2 , HEX: 484147346132 , S/N: C1E25D7B , rev. 0xA5
EMMC ROM 1 (Main User Data) Capacity: 15028 MB (0003AB400000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000) Counter: 34316 , Response: Not Clean
Extended CSD Information :
Extended CSD rev: 1.8 (MMC 5.1)
Boot configuration [179] / Boot Bus Config [177] / H/W Reset Function [162]: 0x38 / 0x00 / 0x01
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Backup saved: HAG4a2_C1E25D7B_20200801_121553.extcsd
EMMC Init completed.

Operation: Write by vendor (Qualcomm/HiSilicon/Omap)

Partition name: oppodycnvbk
Filename: dynamic_nvbk.bin , Offset: 000000005000 , filesize: 10485760 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 664.86 KB/s
Partition name: oppostanvbk
Filename: static_nvbk.bin , Offset: 000000A05000 , filesize: 10485760 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 768.03 KB/s
Partition name: persist
Filename: persist.img , Offset: 000001705000 , filesize: 5132700 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Sparse image found v.1.0 Total chunks: 32
Done writing partition. Write speed: 675.45 KB/s
Partition name: opporeserve1
Filename: emmc_fw.bin , Offset: 000003705000 , filesize: 4194304 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 774.40 KB/s
Partition name: opporeserve2
Filename: opporeserve2.img , Offset: 000003F05000 , filesize: 5300372 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Sparse image found v.1.0 Total chunks: 10
Done writing partition. Write speed: 749.69 KB/s
Partition name: sbl1
Filename: sbl1.mbn , Offset: 000008308000 , filesize: 452656 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 699.75 KB/s
Partition name: rpm
Filename: rpm.mbn , Offset: 000008388000 , filesize: 174884 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 626.26 KB/s
Partition name: tz
Filename: tz.mbn , Offset: 000008408000 , filesize: 1535872 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 746.27 KB/s
Partition name: devcfg
Filename: devcfg.mbn , Offset: 000008608000 , filesize: 40220 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 385.54 KB/s
Partition name: sbl1bak
Filename: sbl1.mbn , Offset: 000008648000 , filesize: 452656 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 710.78 KB/s
Partition name: rpmbak
Filename: rpm.mbn , Offset: 0000086C8000 , filesize: 174884 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 634.04 KB/s
Partition name: tzbak
Filename: tz.mbn , Offset: 000008748000 , filesize: 1535872 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 752.91 KB/s
Partition name: devcfgbak
Filename: devcfg.mbn , Offset: 000008948000 , filesize: 40220 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 385.76 KB/s
Partition name: dsp
Filename: adspso.bin , Offset: 000008988000 , filesize: 16777216 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 773.08 KB/s
Partition name: aboot
Filename: emmc_appsboot.mbn , Offset: 00000A18C000 , filesize: 738876 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 719.78 KB/s
Partition name: abootbak
Filename: emmc_appsboot.mbn , Offset: 00000A28C000 , filesize: 738876 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 728.10 KB/s
Partition name: modem
Filename: NON-HLOS.bin , Offset: 00000A38C000 , filesize: 134217728 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 771.74 KB/s
Partition name: dtbo
Filename: dtbo.img , Offset: 00001238C000 , filesize: 8388608 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 771.27 KB/s
Partition name: vbmeta
Filename: vbmeta.img , Offset: 000012B8C000 , filesize: 4096 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 107.16 KB/s
Partition name: boot
Filename: boot.img , Offset: 000012B9C000 , filesize: 67108864 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 772.04 KB/s
Partition name: recovery
Filename: recovery.img , Offset: 000016B9C000 , filesize: 67108864 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 768.03 KB/s
Partition name: LOGO
Filename: logo.bin , Offset: 00001BB00000 , filesize: 878080 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 724.73 KB/s
Partition name: DRIVER
Filename: DRIVER.ISO , Offset: 00001DB00000 , filesize: 23795712 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 769.82 KB/s
Partition name: cache
Filename: cache.img , Offset: 00001FB00000 , filesize: 6398160 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Sparse image found v.1.0 Total chunks: 15
Done writing partition. Write speed: 740.72 KB/s
Partition name: mdtp
Filename: mdtp.img , Offset: 000030980000 , filesize: 17808306 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 763.34 KB/s
Partition name: lksecapp
Filename: lksecapp.mbn , Offset: 000033000000 , filesize: 57352 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 456.05 KB/s
Partition name: cmnlib
Filename: cmnlib_30.mbn , Offset: 000033020000 , filesize: 213856 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 629.73 KB/s
Partition name: cmnlib64
Filename: cmnlib64_30.mbn , Offset: 000033120000 , filesize: 269088 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 615.89 KB/s
Partition name: keymaster
Filename: keymaster64.mbn , Offset: 000033220000 , filesize: 271480 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 626.81 KB/s
Partition name: lksecappbak
Filename: lksecapp.mbn , Offset: 000033320000 , filesize: 57352 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 457.28 KB/s
Partition name: cmnlibbak
Filename: cmnlib_30.mbn , Offset: 000033340000 , filesize: 213856 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 692.33 KB/s
Partition name: cmnlib64bak
Filename: cmnlib64_30.mbn , Offset: 000033440000 , filesize: 269088 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 658.32 KB/s
Partition name: keymasterbak
Filename: keymaster64.mbn , Offset: 000033540000 , filesize: 271480 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 672.74 KB/s
Partition name: apdp
Filename: dpAP.mbn , Offset: 000033800000 , filesize: 13248 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 180.21 KB/s
Partition name: system
Filename: system.img , Offset: 00003F000000 , filesize: 3208174868 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Sparse image found v.1.0 Total chunks: 4714
Done writing partition. Write speed: 743.25 KB/s
Partition name: vendor
Filename: vendor.img , Offset: 000115900000 , filesize: 978552928 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Sparse image found v.1.0 Total chunks: 2907
Done writing partition. Write speed: 721.23 KB/s

All done time: [01:53:29:845]








layder 08-03-2020 14:08

at last operation - Write by vendor you need write backup only secure partition
If you write all partition - you restore you device to original state

you need:
1) backup secure partitioon only, or backup all without usedata, syste, cache
2) Write work dump or extracted ofp firmware
3) restore only secute partition if you write dump

jamohaki 08-03-2020 17:41

after write ofp firmware i write below back up i am right?


OPPO A3S CPH1803EX_11_A.17_Samsung eMMC_oppodycnvbk + oppostanvbk + modemst1 + modemst2 + fsg + sec + modem.7z

layder 08-03-2020 22:55

Quote:

Originally Posted by jamohaki (Post 14169380)
after write ofp firmware i write below back up i am right?


OPPO A3S CPH1803EX_11_A.17_Samsung eMMC_oppodycnvbk + oppostanvbk + modemst1 + modemst2 + fsg + sec + modem.7z

you need restore this partition from you backup

jamohaki 08-04-2020 08:19

Quote:

Originally Posted by layder (Post 14169183)
at last operation - Write by vendor you need write backup only secure partition
If you write all partition - you restore you device to original state

you need:
1) backup secure partitioon only, or backup all without usedata, syste, cache
2) Write work dump or extracted ofp firmware
3) restore only secute partition if you write dump


i write my secure partition back up but still phone dead.but i made the secure partition back up when phone already in edl state.anyway to solve this?

...:::::NP™:::::... 08-04-2020 10:14

Hi,

Pay attention, if you do have the Phone Secure Area data is backup, just erase the whole eMMC completely, then apply my method from the beginning.

After you do complete the recommended procedure if you get still EDL problem then it's hardware components are damaged by over hit soldering.

Just makes jumper one by one, 1'st makes CLK if still EDL, then also makes CMD.





Post result.

jamohaki 08-04-2020 17:16

ok thanks for the tips but just 2 questions : i made Phone Secure Area data backup but after phone already in edl mode will that back up work? if not going to work what can i do?

jamohaki 08-06-2020 07:19

here is the info log


Setting frequence to 21 MHz
CMD Pullup Level: 1804 mV
CMD Active Level: 2062 mV
EMMC Device Information :
EMMC CID: 90014A484147346132A5C1E25D7BC5D2
EMMC CSD: D02701328F5903FFFFFFFFE78A400016
EMMC Manufacture : SKHYNIX , EMMC NAME: HAG4a2 , HEX: 484147346132 , S/N: C1E25D7B , rev. 0xA5
EMMC ROM 1 (Main User Data) Capacity: 15028 MB (0003AB400000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000) Counter: 34316 , Response: Not Clean
Extended CSD Information :
Extended CSD rev: 1.8 (MMC 5.1)
Boot configuration [179] / Boot Bus Config [177] / H/W Reset Function [162]: 0x38 / 0x00 / 0x01
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Backup saved: HAG4a2_C1E25D7B_20200806_090427.extcsd
EMMC Init completed.

Scanning soft partitions
GPT header is found and is valid
Partition: oppodycnvbk, [000000005000 - 000000A05000], size: 000000A00000 (10.0 MB)
Partition: oppostanvbk, [000000A05000 - 000001405000], size: 000000A00000 (10.0 MB)
Partition: modemst1, [000001405000 - 000001585000], size: 000000180000 (1.50 MB)
Partition: modemst2, [000001585000 - 000001705000], size: 000000180000 (1.50 MB)
Partition: persist, [000001705000 - 000003705000], size: 000002000000 (32.0 MB)
Partition: opporeserve1, [000003705000 - 000003F05000], size: 000000800000 (8.00 MB)
Partition: opporeserve2, [000003F05000 - 000007F05000], size: 000004000000 (64.0 MB)
Partition: reserve_exp1, [000007F05000 - 000008105000], size: 000000200000 (2.00 MB)
Partition: reserve_exp2, [000008105000 - 000008305000], size: 000000200000 (2.00 MB)
Partition: fsc, [000008305000 - 000008305400], size: 000000000400 (1.00 KB)
Partition: ssd, [000008306000 - 000008308000], size: 000000002000 (8.00 KB)
Partition: sbl1, [000008308000 - 000008388000], size: 000000080000 (512. KB)
Partition: rpm, [000008388000 - 000008408000], size: 000000080000 (512. KB)
Partition: tz, [000008408000 - 000008608000], size: 000000200000 (2.00 MB)
Partition: devcfg, [000008608000 - 000008648000], size: 000000040000 (256. KB)
Partition: sbl1bak, [000008648000 - 0000086C8000], size: 000000080000 (512. KB)
Partition: rpmbak, [0000086C8000 - 000008748000], size: 000000080000 (512. KB)
Partition: tzbak, [000008748000 - 000008948000], size: 000000200000 (2.00 MB)
Partition: devcfgbak, [000008948000 - 000008988000], size: 000000040000 (256. KB)
Partition: dsp, [000008988000 - 000009988000], size: 000001000000 (16.0 MB)
Partition: DDR, [00000A000000 - 00000A008000], size: 000000008000 (32.0 KB)
Partition: fsg, [00000A008000 - 00000A188000], size: 000000180000 (1.50 MB)
Partition: sec, [00000A188000 - 00000A18C000], size: 000000004000 (16.0 KB)
Partition: aboot, [00000A18C000 - 00000A28C000], size: 000000100000 (1.00 MB)
Partition: abootbak, [00000A28C000 - 00000A38C000], size: 000000100000 (1.00 MB)
Partition: modem, [00000A38C000 - 00001238C000], size: 000008000000 (128. MB)
Partition: dtbo, [00001238C000 - 000012B8C000], size: 000000800000 (8.00 MB)
Partition: vbmeta, [000012B8C000 - 000012B9C000], size: 000000010000 (64.0 KB)
Partition: boot, [000012B9C000 - 000016B9C000], size: 000004000000 (64.0 MB)
Partition: recovery, [000016B9C000 - 00001AB9C000], size: 000004000000 (64.0 MB)
Partition: devinfo, [00001AB9C000 - 00001AC9C000], size: 000000100000 (1.00 MB)
Partition: splash, [00001B000000 - 00001BB00000], size: 000000B00000 (11.0 MB)
Partition: LOGO, [00001BB00000 - 00001DB00000], size: 000002000000 (32.0 MB)
Partition: DRIVER, [00001DB00000 - 00001FB00000], size: 000002000000 (32.0 MB)
Partition: cache, [00001FB00000 - 00002FB00000], size: 000010000000 (256. MB)
Partition: misc, [00002FB00000 - 00002FC00000], size: 000000100000 (1.00 MB)
Partition: keystore, [00002FC00000 - 00002FC80000], size: 000000080000 (512. KB)
Partition: config, [00002FC80000 - 00002FC88000], size: 000000008000 (32.0 KB)
Partition: oem, [00002FC88000 - 00002FD88000], size: 000000100000 (1.00 MB)
Partition: limits, [000030000000 - 000030008000], size: 000000008000 (32.0 KB)
Partition: mota, [000030800000 - 000030880000], size: 000000080000 (512. KB)
Partition: dip, [000030880000 - 000030980000], size: 000000100000 (1.00 MB)
Partition: mdtp, [000030980000 - 000032980000], size: 000002000000 (32.0 MB)
Partition: syscfg, [000032980000 - 000032A00000], size: 000000080000 (512. KB)
Partition: mcfg, [000032A00000 - 000032E00000], size: 000000400000 (4.00 MB)
Partition: lksecapp, [000033000000 - 000033020000], size: 000000020000 (128. KB)
Partition: cmnlib, [000033020000 - 000033120000], size: 000000100000 (1.00 MB)
Partition: cmnlib64, [000033120000 - 000033220000], size: 000000100000 (1.00 MB)
Partition: keymaster, [000033220000 - 000033320000], size: 000000100000 (1.00 MB)
Partition: lksecappbak, [000033320000 - 000033340000], size: 000000020000 (128. KB)
Partition: cmnlibbak, [000033340000 - 000033440000], size: 000000100000 (1.00 MB)
Partition: cmnlib64bak, [000033440000 - 000033540000], size: 000000100000 (1.00 MB)
Partition: keymasterbak, [000033540000 - 000033640000], size: 000000100000 (1.00 MB)
Partition: apdp, [000033800000 - 000033840000], size: 000000040000 (256. KB)
Partition: msadp, [000033840000 - 000033880000], size: 000000040000 (256. KB)
Partition: dpo, [000033880000 - 000033882000], size: 000000002000 (8.00 KB)
Partition: logdump, [000033882000 - 000037882000], size: 000004000000 (64.0 MB)
Partition: vm-kystore, [000037882000 - 000037982000], size: 000000100000 (1.00 MB)
Partition: vm-data, [000037982000 - 000038382000], size: 000000A00000 (10.0 MB)
Partition: hyp, [000038800000 - 000039000000], size: 000000800000 (8.00 MB)
Partition: vm-system, [000039000000 - 00003D000000], size: 000004000000 (64.0 MB)
Partition: vm-linux, [00003D000000 - 00003F000000], size: 000002000000 (32.0 MB)
Partition: system, [00003F000000 - 000115900000], size: 0000D6900000 (3.35 GB)
Partition: vendor, [000115900000 - 000157860000], size: 000041F60000 (1.03 GB)
Partition: userdata, [000158000000 - 0003AB3FBE00], size: 0002533FBE00 (9.30 GB)
GPT header successfully parsed

jamohaki 08-06-2020 08:16

ok read info from easyjtag classic:

Z3X EasyJtag Software ver. 3.7.0.11
Loading eMMC GEN1 Firmware... IO: 1800 mV
Box S/N: , ,FW Ver.: 01.63
CMD Pullup Level:1815 mV
CMD Active Level:2052 mV
Box IO Level:1800 mV
CLK Rate:21000 kHz
Bus Width:1bit,SDR
HiPower mode is ON!
---------- eMMC Device Information ----------

eMMC CID : 90014A484147346132A5C1E25D7BC5D2
eMMC CSD : D02701328F5903FFFFFFFFE78A400016
eMMC Manufacturer ID: 0090 , OEM ID: 014A
eMMC Date: 12/2018 Rev.0xA5
eMMC NAME: HAG4a2 , S/N: 3252837755
eMMC NAME (HEX): 484147346132
EMMC ROM1 (Main User Data) Capacity: 15028 MB
EMMC ROM2 (Boot Partition 1) Capacity: 4096 kB
EMMC ROM3 (Boot Partition 2) Capacity: 4096 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 kB
EMMC RPMB is programmed and written 34316 times
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
EMMC Password Locked: No
Extended CSD rev 1.8 (MMC 5.1)
Boot configuration [PARTITION_CONFIG: 0x38] Boot from:ROM1 (Main User Area)
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x38.
H/W reset function [RST_N_FUNCTION]: 0x01
High-capacity WP group size [HC_WP_GRP_SIZE: 0x00002000]
Partitioning Support [PARTITIONING_SUPPORT]: 0x07
Device support partitioning feature
Device can have enhanced tech.
Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00
---------------------------------------------
Backup saved: HAG4a2_3252837755_20200806_1011.extcsd
Warning! Main and backup partition tables differ!
Warning! One or more CRCs don't match. You should repair the disk!
Caution: Found protective or hybrid MBR and corrupt GPT.
Real (Hardware) Disk/Image size: 1D5A000 sectors 14.7 GiB
Soft (Partitioned) Disk/Image size: 1D59FDA sectors 14.7 GiB
Disk identifier (GUID): 98101B32-BBE2-4BF2-A06E-2BB33D000C20
Logical sector size: 0x200 bytes ,First/Last usable sector: 19,30777325
Partition info successfully found
------ Android information ------
Detected LINUX(Android) SYSTEM : 0x003F000000 (3.352GB)
Short EXT fs info:
Size: 3.298GB
Block size: 4.0KB
Inode size: 256
Inodes: 216432
Short Android info:
Build ID: OPM1.171019.026
Release Base ID: 8.1.0
Security Path: 2019-03-05
Architecture ABI: arm64-v8a
Device manufacturer: OPPO
Build Description: msm8953_64-user 8.1.0 OPM1.171019.026 eng.root.20190323.213841 release-keys
Backup saved: BuildProp_20200806_1011.txt
---------------------------------------------
Detected USERDATA USERDATA : 0x0158000000 (9.299GB)
Short EXT fs info:
Size: 7.500GB
Block size: 4.0KB
Inode size: 256
Inodes: 491520
Short userdata info:
Unable to read gesture.key , code 2
Done.

jamohaki 08-07-2020 08:29

problem not solved who can help please?

jamohaki 08-11-2020 12:20

EasyJtag Suite Classic ver.: 3.7.0.11 / wxWidgets 3.1.3-W-U started.
OS ver.: Windows 7 (build 7601, Service Pack 1). Admin rights FAIL
Autorun Agent ver:1.0.0.0
Crash Reporting ver:1.4.0.3
EasyJTAG SPI Plugin ver:1.1.1.13
Android ADB API ver:2.0.0.0
FTDI API ver:3.2.4.0
LibUSB API ver:1.2.6.0
Visual C++ Runtime ver:10.0.30319.1
Setting box Pinout ...

Box Drivers version: 3.0.1.0, are OK
Z3X Card Serial : , ver: 22
Z3X Card Activation [JTAGPLUS] : NOT ACTIVATED
Z3X Card Activation [LG] : NOT ACTIVATED
Z3X Card Activation [SAMS] : NOT ACTIVATED
Z3X Card Activation [JTAG] : ACTIVATED


For more information press F1 to open local help or visit our wiki

Found 3 serial devices
COM1 ACPI\PNP0501 Communications Port (COM1)
COM17 USB\VID_0325&PID_0032&REV_0100&MI_00 Easy Jtag Control Port (COM17)
COM26 USB\VID_05C6&PID_9008&REV_0000 Qualcomm HS-USB QDLoader 9008 (COM26)
Selected pinout: EasyJTAG GEN1 ISP Pinout
Change EasyJTAG Pinout OK
Z3X EasyJtag Software ver. 3.7.0.11
Loading eMMC GEN1 Firmware... IO: 1850 mV
Box S/N: 1616120653F9FBE6, ,FW Ver.: 01.63
CMD Pullup Level:1907 mV
CMD Active Level:2062 mV
Box IO Level:1850 mV
CLK Rate:21000 kHz
Bus Width:1bit,SDR
HiPower mode is off!
---------- eMMC Device Information ----------

eMMC CID : 90014A484147346132A5C1E25D7BC5D2
eMMC CSD : D02701328F5903FFFFFFFFE78A400016
eMMC Manufacturer ID: 0090 , OEM ID: 014A
eMMC Date: 12/2018 Rev.0xA5
eMMC NAME: HAG4a2 , S/N: 3252837755
eMMC NAME (HEX): 484147346132
EMMC ROM1 (Main User Data) Capacity: 15028 MB
EMMC ROM2 (Boot Partition 1) Capacity: 4096 kB
EMMC ROM3 (Boot Partition 2) Capacity: 4096 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 kB
EMMC RPMB is programmed and written 34316 times
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
EMMC Password Locked: No
Extended CSD rev 1.8 (MMC 5.1)
Boot configuration [PARTITION_CONFIG: 0x38] Boot from:ROM1 (Main User Area)
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x38.
H/W reset function [RST_N_FUNCTION]: 0x01
High-capacity WP group size [HC_WP_GRP_SIZE: 0x00002000]
Partitioning Support [PARTITIONING_SUPPORT]: 0x07
Device support partitioning feature
Device can have enhanced tech.
Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00
---------------------------------------------
Backup saved: HAG4a2_3252837755_20200811_1413.extcsd
Warning! Main and backup partition tables differ!
Warning! One or more CRCs don't match. You should repair the disk!
Caution: Found protective or hybrid MBR and corrupt GPT.
Real (Hardware) Disk/Image size: 1D5A000 sectors 14.7 GiB
Soft (Partitioned) Disk/Image size: 1D59FDA sectors 14.7 GiB
Disk identifier (GUID): 98101B32-BBE2-4BF2-A06E-2BB33D000C20
Logical sector size: 0x200 bytes ,First/Last usable sector: 19,30777325
Partition info successfully found
------ Android information ------
Detected LINUX(Android) SYSTEM : 0x003F000000 (3.352GB)
Short EXT fs info:
Size: 3.298GB
Block size: 4.0KB
Inode size: 256
Inodes: 216432
Short Android info:
Build ID: OPM1.171019.026
Release Base ID: 8.1.0
Security Path: 2019-03-05
Architecture ABI: arm64-v8a
Device manufacturer: OPPO
Build Description: msm8953_64-user 8.1.0 OPM1.171019.026 eng.root.20190323.213841 release-keys
Backup saved: BuildProp_20200811_1413.txt
---------------------------------------------
Detected USERDATA USERDATA : 0x0158000000 (9.299GB)
Short EXT fs info:
Size: 7.500GB
Block size: 4.0KB
Inode size: 256
Inodes: 491520
Short userdata info:
Unable to read gesture.key , code 2
Done.

nour2014 08-12-2020 03:50

good work bro thanks alot

T0T0 08-27-2020 09:22

do you have fulldump for skhynix emmc

...:::::NP™:::::... 08-27-2020 13:52

@ T0T0



I don't have it !!

Unfortunately the South African region did not seen the SKhynix eMMC Building Oppo A3S Phone.

T0T0 08-28-2020 03:14

ok sir thanks i have 3 pcs a3s all skhynix emmc

tapas770 09-04-2020 11:18

very useful thread, Thanks for share

cestin 09-04-2020 17:28

really it helps bro thanks for your hardwork

intik600 09-04-2020 17:46

Thank you for sharing you experience

manlors 03-29-2021 17:04

nice sir, this may be the solution I've been seeking. I'll update later the result after following your procedures.

Samacy 04-10-2021 07:02

Thanks for this very detailed thread.

chmsc_ELX 06-23-2021 14:50

A3s can be revive using z3x jtag 1st gen box? in win 8 is it gonna work?

...:::::NP™:::::... 06-23-2021 15:55

@ chmsc_ELX

Read the thread from beginning, You must read carefully #4 or #5 about your asking requirement already has been decently discussion there.


All times are GMT +1. The time now is 15:47.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2022 DragonByte Technologies Ltd.
- GSM Hosting Ltd. - 1999-2017 -

Page generated in 0.53328 seconds with 6 queries

SEO by vBSEO