Oppo A3s [CPH1803][EDL MODE][DEAD RECOVERED][DONE] by Easy JTAG_Palash Ahammad - Page 3 - GSM-Forum

jamohaki · 08-03-2020, 17:41

after write ofp firmware i write below back up i am right?

OPPO A3S CPH1803EX_11_A.17_Samsung eMMC_oppodycnvbk + oppostanvbk + modemst1 + modemst2 + fsg + sec + modem.7z

layder · 08-03-2020, 22:55

Quote:

Originally Posted by jamohaki

after write ofp firmware i write below back up i am right?

OPPO A3S CPH1803EX_11_A.17_Samsung eMMC_oppodycnvbk + oppostanvbk + modemst1 + modemst2 + fsg + sec + modem.7z

you need restore this partition from you backup

jamohaki · 08-04-2020, 08:19

Quote:

Originally Posted by layder

at last operation - Write by vendor you need write backup only secure partition
If you write all partition - you restore you device to original state

you need:
1) backup secure partitioon only, or backup all without usedata, syste, cache
2) Write work dump or extracted ofp firmware
3) restore only secute partition if you write dump

i write my secure partition back up but still phone dead.but i made the secure partition back up when phone already in edl state.anyway to solve this?

**...:::::NP™:::::...** · 08-04-2020, 10:14

Hi,

Pay attention, if you do have the Phone Secure Area data is backup, just erase the whole eMMC completely, then apply my method from the beginning.

After you do complete the recommended procedure if you get still EDL problem then it's hardware components are damaged by over hit soldering.

Just makes jumper one by one, 1'st makes CLK if still EDL, then also makes CMD.

Post result.

jamohaki · 08-04-2020, 17:16

ok thanks for the tips but just 2 questions : i made Phone Secure Area data backup but after phone already in edl mode will that back up work? if not going to work what can i do?

jamohaki · 08-06-2020, 07:19

here is the info log

Setting frequence to 21 MHz
CMD Pullup Level: 1804 mV
CMD Active Level: 2062 mV
EMMC Device Information :
EMMC CID: 90014A484147346132A5C1E25D7BC5D2
EMMC CSD: D02701328F5903FFFFFFFFE78A400016
EMMC Manufacture : SKHYNIX , EMMC NAME: HAG4a2 , HEX: 484147346132 , S/N: C1E25D7B , rev. 0xA5
EMMC ROM 1 (Main User Data) Capacity: 15028 MB (0003AB400000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000) Counter: 34316 , Response: Not Clean
Extended CSD Information :
Extended CSD rev: 1.8 (MMC 5.1)
Boot configuration [179] / Boot Bus Config [177] / H/W Reset Function [162]: 0x38 / 0x00 / 0x01
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Backup saved: HAG4a2_C1E25D7B_20200806_090427.extcsd
EMMC Init completed.

Scanning soft partitions
GPT header is found and is valid
Partition: oppodycnvbk, [000000005000 - 000000A05000], size: 000000A00000 (10.0 MB)
Partition: oppostanvbk, [000000A05000 - 000001405000], size: 000000A00000 (10.0 MB)
Partition: modemst1, [000001405000 - 000001585000], size: 000000180000 (1.50 MB)
Partition: modemst2, [000001585000 - 000001705000], size: 000000180000 (1.50 MB)
Partition: persist, [000001705000 - 000003705000], size: 000002000000 (32.0 MB)
Partition: opporeserve1, [000003705000 - 000003F05000], size: 000000800000 (8.00 MB)
Partition: opporeserve2, [000003F05000 - 000007F05000], size: 000004000000 (64.0 MB)
Partition: reserve_exp1, [000007F05000 - 000008105000], size: 000000200000 (2.00 MB)
Partition: reserve_exp2, [000008105000 - 000008305000], size: 000000200000 (2.00 MB)
Partition: fsc, [000008305000 - 000008305400], size: 000000000400 (1.00 KB)
Partition: ssd, [000008306000 - 000008308000], size: 000000002000 (8.00 KB)
Partition: sbl1, [000008308000 - 000008388000], size: 000000080000 (512. KB)
Partition: rpm, [000008388000 - 000008408000], size: 000000080000 (512. KB)
Partition: tz, [000008408000 - 000008608000], size: 000000200000 (2.00 MB)
Partition: devcfg, [000008608000 - 000008648000], size: 000000040000 (256. KB)
Partition: sbl1bak, [000008648000 - 0000086C8000], size: 000000080000 (512. KB)
Partition: rpmbak, [0000086C8000 - 000008748000], size: 000000080000 (512. KB)
Partition: tzbak, [000008748000 - 000008948000], size: 000000200000 (2.00 MB)
Partition: devcfgbak, [000008948000 - 000008988000], size: 000000040000 (256. KB)
Partition: dsp, [000008988000 - 000009988000], size: 000001000000 (16.0 MB)
Partition: DDR, [00000A000000 - 00000A008000], size: 000000008000 (32.0 KB)
Partition: fsg, [00000A008000 - 00000A188000], size: 000000180000 (1.50 MB)
Partition: sec, [00000A188000 - 00000A18C000], size: 000000004000 (16.0 KB)
Partition: aboot, [00000A18C000 - 00000A28C000], size: 000000100000 (1.00 MB)
Partition: abootbak, [00000A28C000 - 00000A38C000], size: 000000100000 (1.00 MB)
Partition: modem, [00000A38C000 - 00001238C000], size: 000008000000 (128. MB)
Partition: dtbo, [00001238C000 - 000012B8C000], size: 000000800000 (8.00 MB)
Partition: vbmeta, [000012B8C000 - 000012B9C000], size: 000000010000 (64.0 KB)
Partition: boot, [000012B9C000 - 000016B9C000], size: 000004000000 (64.0 MB)
Partition: recovery, [000016B9C000 - 00001AB9C000], size: 000004000000 (64.0 MB)
Partition: devinfo, [00001AB9C000 - 00001AC9C000], size: 000000100000 (1.00 MB)
Partition: splash, [00001B000000 - 00001BB00000], size: 000000B00000 (11.0 MB)
Partition: LOGO, [00001BB00000 - 00001DB00000], size: 000002000000 (32.0 MB)
Partition: DRIVER, [00001DB00000 - 00001FB00000], size: 000002000000 (32.0 MB)
Partition: cache, [00001FB00000 - 00002FB00000], size: 000010000000 (256. MB)
Partition: misc, [00002FB00000 - 00002FC00000], size: 000000100000 (1.00 MB)
Partition: keystore, [00002FC00000 - 00002FC80000], size: 000000080000 (512. KB)
Partition: config, [00002FC80000 - 00002FC88000], size: 000000008000 (32.0 KB)
Partition: oem, [00002FC88000 - 00002FD88000], size: 000000100000 (1.00 MB)
Partition: limits, [000030000000 - 000030008000], size: 000000008000 (32.0 KB)
Partition: mota, [000030800000 - 000030880000], size: 000000080000 (512. KB)
Partition: dip, [000030880000 - 000030980000], size: 000000100000 (1.00 MB)
Partition: mdtp, [000030980000 - 000032980000], size: 000002000000 (32.0 MB)
Partition: syscfg, [000032980000 - 000032A00000], size: 000000080000 (512. KB)
Partition: mcfg, [000032A00000 - 000032E00000], size: 000000400000 (4.00 MB)
Partition: lksecapp, [000033000000 - 000033020000], size: 000000020000 (128. KB)
Partition: cmnlib, [000033020000 - 000033120000], size: 000000100000 (1.00 MB)
Partition: cmnlib64, [000033120000 - 000033220000], size: 000000100000 (1.00 MB)
Partition: keymaster, [000033220000 - 000033320000], size: 000000100000 (1.00 MB)
Partition: lksecappbak, [000033320000 - 000033340000], size: 000000020000 (128. KB)
Partition: cmnlibbak, [000033340000 - 000033440000], size: 000000100000 (1.00 MB)
Partition: cmnlib64bak, [000033440000 - 000033540000], size: 000000100000 (1.00 MB)
Partition: keymasterbak, [000033540000 - 000033640000], size: 000000100000 (1.00 MB)
Partition: apdp, [000033800000 - 000033840000], size: 000000040000 (256. KB)
Partition: msadp, [000033840000 - 000033880000], size: 000000040000 (256. KB)
Partition: dpo, [000033880000 - 000033882000], size: 000000002000 (8.00 KB)
Partition: logdump, [000033882000 - 000037882000], size: 000004000000 (64.0 MB)
Partition: vm-kystore, [000037882000 - 000037982000], size: 000000100000 (1.00 MB)
Partition: vm-data, [000037982000 - 000038382000], size: 000000A00000 (10.0 MB)
Partition: hyp, [000038800000 - 000039000000], size: 000000800000 (8.00 MB)
Partition: vm-system, [000039000000 - 00003D000000], size: 000004000000 (64.0 MB)
Partition: vm-linux, [00003D000000 - 00003F000000], size: 000002000000 (32.0 MB)
Partition: system, [00003F000000 - 000115900000], size: 0000D6900000 (3.35 GB)
Partition: vendor, [000115900000 - 000157860000], size: 000041F60000 (1.03 GB)
Partition: userdata, [000158000000 - 0003AB3FBE00], size: 0002533FBE00 (9.30 GB)
GPT header successfully parsed

jamohaki · 08-06-2020, 08:16

ok read info from easyjtag classic:

Z3X EasyJtag Software ver. 3.7.0.11
Loading eMMC GEN1 Firmware... IO: 1800 mV
Box S/N: , ,FW Ver.: 01.63
CMD Pullup Level:1815 mV
CMD Active Level:2052 mV
Box IO Level:1800 mV
CLK Rate:21000 kHz
Bus Width:1bit,SDR
HiPower mode is ON!
---------- eMMC Device Information ----------

eMMC CID : 90014A484147346132A5C1E25D7BC5D2
eMMC CSD : D02701328F5903FFFFFFFFE78A400016
eMMC Manufacturer ID: 0090 , OEM ID: 014A
eMMC Date: 12/2018 Rev.0xA5
eMMC NAME: HAG4a2 , S/N: 3252837755
eMMC NAME (HEX): 484147346132
EMMC ROM1 (Main User Data) Capacity: 15028 MB
EMMC ROM2 (Boot Partition 1) Capacity: 4096 kB
EMMC ROM3 (Boot Partition 2) Capacity: 4096 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 kB
EMMC RPMB is programmed and written 34316 times
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
EMMC Password Locked: No
Extended CSD rev 1.8 (MMC 5.1)
Boot configuration [PARTITION_CONFIG: 0x38] Boot from:ROM1 (Main User Area)
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x38.
H/W reset function [RST_N_FUNCTION]: 0x01
High-capacity WP group size [HC_WP_GRP_SIZE: 0x00002000]
Partitioning Support [PARTITIONING_SUPPORT]: 0x07
Device support partitioning feature
Device can have enhanced tech.
Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00
---------------------------------------------
Backup saved: HAG4a2_3252837755_20200806_1011.extcsd
Warning! Main and backup partition tables differ!
Warning! One or more CRCs don't match. You should repair the disk!
Caution: Found protective or hybrid MBR and corrupt GPT.
Real (Hardware) Disk/Image size: 1D5A000 sectors 14.7 GiB
Soft (Partitioned) Disk/Image size: 1D59FDA sectors 14.7 GiB
Disk identifier (GUID): 98101B32-BBE2-4BF2-A06E-2BB33D000C20
Logical sector size: 0x200 bytes ,First/Last usable sector: 19,30777325
Partition info successfully found
------ Android information ------
Detected LINUX(Android) SYSTEM : 0x003F000000 (3.352GB)
Short EXT fs info:
Size: 3.298GB
Block size: 4.0KB
Inode size: 256
Inodes: 216432
Short Android info:
Build ID: OPM1.171019.026
Release Base ID: 8.1.0
Security Path: 2019-03-05
Architecture ABI: arm64-v8a
Device manufacturer: OPPO
Build Description: msm8953_64-user 8.1.0 OPM1.171019.026 eng.root.20190323.213841 release-keys
Backup saved: BuildProp_20200806_1011.txt
---------------------------------------------
Detected USERDATA USERDATA : 0x0158000000 (9.299GB)
Short EXT fs info:
Size: 7.500GB
Block size: 4.0KB
Inode size: 256
Inodes: 491520
Short userdata info:
Unable to read gesture.key , code 2
Done.

jamohaki · 08-07-2020, 08:29

problem not solved who can help please?

jamohaki · 08-11-2020, 12:20

EasyJtag Suite Classic ver.: 3.7.0.11 / wxWidgets 3.1.3-W-U started.
OS ver.: Windows 7 (build 7601, Service Pack 1). Admin rights FAIL
Autorun Agent ver:1.0.0.0
Crash Reporting ver:1.4.0.3
EasyJTAG SPI Plugin ver:1.1.1.13
Android ADB API ver:2.0.0.0
FTDI API ver:3.2.4.0
LibUSB API ver:1.2.6.0
Visual C++ Runtime ver:10.0.30319.1
Setting box Pinout ...

Box Drivers version: 3.0.1.0, are OK
Z3X Card Serial : , ver: 22
Z3X Card Activation [JTAGPLUS] : NOT ACTIVATED
Z3X Card Activation [LG] : NOT ACTIVATED
Z3X Card Activation [SAMS] : NOT ACTIVATED
Z3X Card Activation [JTAG] : ACTIVATED

For more information press F1 to open local help or visit our wiki

Found 3 serial devices
COM1 ACPI\PNP0501 Communications Port (COM1)
COM17 USB\VID_0325&PID_0032&REV_0100&MI_00 Easy Jtag Control Port (COM17)
COM26 USB\VID_05C6&PID_9008&REV_0000 Qualcomm HS-USB QDLoader 9008 (COM26)
Selected pinout: EasyJTAG GEN1 ISP Pinout
Change EasyJTAG Pinout OK
Z3X EasyJtag Software ver. 3.7.0.11
Loading eMMC GEN1 Firmware... IO: 1850 mV
Box S/N: 1616120653F9FBE6, ,FW Ver.: 01.63
CMD Pullup Level:1907 mV
CMD Active Level:2062 mV
Box IO Level:1850 mV
CLK Rate:21000 kHz
Bus Width:1bit,SDR
HiPower mode is off!
---------- eMMC Device Information ----------

eMMC CID : 90014A484147346132A5C1E25D7BC5D2
eMMC CSD : D02701328F5903FFFFFFFFE78A400016
eMMC Manufacturer ID: 0090 , OEM ID: 014A
eMMC Date: 12/2018 Rev.0xA5
eMMC NAME: HAG4a2 , S/N: 3252837755
eMMC NAME (HEX): 484147346132
EMMC ROM1 (Main User Data) Capacity: 15028 MB
EMMC ROM2 (Boot Partition 1) Capacity: 4096 kB
EMMC ROM3 (Boot Partition 2) Capacity: 4096 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 kB
EMMC RPMB is programmed and written 34316 times
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
EMMC Password Locked: No
Extended CSD rev 1.8 (MMC 5.1)
Boot configuration [PARTITION_CONFIG: 0x38] Boot from:ROM1 (Main User Area)
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x38.
H/W reset function [RST_N_FUNCTION]: 0x01
High-capacity WP group size [HC_WP_GRP_SIZE: 0x00002000]
Partitioning Support [PARTITIONING_SUPPORT]: 0x07
Device support partitioning feature
Device can have enhanced tech.
Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00
---------------------------------------------
Backup saved: HAG4a2_3252837755_20200811_1413.extcsd
Warning! Main and backup partition tables differ!
Warning! One or more CRCs don't match. You should repair the disk!
Caution: Found protective or hybrid MBR and corrupt GPT.
Real (Hardware) Disk/Image size: 1D5A000 sectors 14.7 GiB
Soft (Partitioned) Disk/Image size: 1D59FDA sectors 14.7 GiB
Disk identifier (GUID): 98101B32-BBE2-4BF2-A06E-2BB33D000C20
Logical sector size: 0x200 bytes ,First/Last usable sector: 19,30777325
Partition info successfully found
------ Android information ------
Detected LINUX(Android) SYSTEM : 0x003F000000 (3.352GB)
Short EXT fs info:
Size: 3.298GB
Block size: 4.0KB
Inode size: 256
Inodes: 216432
Short Android info:
Build ID: OPM1.171019.026
Release Base ID: 8.1.0
Security Path: 2019-03-05
Architecture ABI: arm64-v8a
Device manufacturer: OPPO
Build Description: msm8953_64-user 8.1.0 OPM1.171019.026 eng.root.20190323.213841 release-keys
Backup saved: BuildProp_20200811_1413.txt
---------------------------------------------
Detected USERDATA USERDATA : 0x0158000000 (9.299GB)
Short EXT fs info:
Size: 7.500GB
Block size: 4.0KB
Inode size: 256
Inodes: 491520
Short userdata info:
Unable to read gesture.key , code 2
Done.

nour2014 · 08-12-2020, 03:50

good work bro thanks alot

T0T0 · 08-27-2020, 09:22

do you have fulldump for skhynix emmc

**...:::::NP™:::::...** · 08-27-2020, 13:52

@ T0T0

I don't have it !!

Unfortunately the South African region did not seen the SKhynix eMMC Building Oppo A3S Phone.

T0T0 · 08-28-2020, 03:14

ok sir thanks i have 3 pcs a3s all skhynix emmc

tapas770 · 09-04-2020, 11:18

very useful thread, Thanks for share

cestin · 09-04-2020, 17:28

really it helps bro thanks for your hardwork

08-04-2020, 10:14	#34 (permalink)
...:::::NP™:::::... Moderator Join Date: Nov 2009 Location: South Africa > Bangladesh Age: 40 Posts: 10,802 Member: 1162626 Status: Online Sonork: 100.1591727 QQ:2337938173 Thanks Meter: 11,053	Hi, Pay attention, if you do have the Phone Secure Area data is backup, just erase the whole eMMC completely, then apply my method from the beginning. After you do complete the recommended procedure if you get still EDL problem then it's hardware components are damaged by over hit soldering. Just makes jumper one by one, 1'st makes CLK if still EDL, then also makes CMD. Post result. __________________ -------------------------- Use Search Button to get Instant Result \| Follow Forum Rules Avoid Spams in the forum to prevent ban your account.

08-27-2020, 13:52	#42 (permalink)
...:::::NP™:::::... Moderator Join Date: Nov 2009 Location: South Africa > Bangladesh Age: 40 Posts: 10,802 Member: 1162626 Status: Online Sonork: 100.1591727 QQ:2337938173 Thanks Meter: 11,053	@ T0T0 I don't have it !! Unfortunately the South African region did not seen the SKhynix eMMC Building Oppo A3S Phone. __________________ -------------------------- Use Search Button to get Instant Result \| Follow Forum Rules Avoid Spams in the forum to prevent ban your account.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

08-03-2020, 17:41	#31 (permalink)
jamohaki No Life Poster Join Date: Sep 2004 Age: 51 Posts: 2,066 Member: 83397 Status: Offline Thanks Meter: 193	after write ofp firmware i write below back up i am right? OPPO A3S CPH1803EX_11_A.17_Samsung eMMC_oppodycnvbk + oppostanvbk + modemst1 + modemst2 + fsg + sec + modem.7z

08-04-2020, 17:16	#35 (permalink)
jamohaki No Life Poster Join Date: Sep 2004 Age: 51 Posts: 2,066 Member: 83397 Status: Offline Thanks Meter: 193	ok thanks for the tips but just 2 questions : i made Phone Secure Area data backup but after phone already in edl mode will that back up work? if not going to work what can i do?

08-06-2020, 07:19	#36 (permalink)
jamohaki No Life Poster Join Date: Sep 2004 Age: 51 Posts: 2,066 Member: 83397 Status: Offline Thanks Meter: 193	here is the info log Setting frequence to 21 MHz CMD Pullup Level: 1804 mV CMD Active Level: 2062 mV EMMC Device Information : EMMC CID: 90014A484147346132A5C1E25D7BC5D2 EMMC CSD: D02701328F5903FFFFFFFFE78A400016 EMMC Manufacture : SKHYNIX , EMMC NAME: HAG4a2 , HEX: 484147346132 , S/N: C1E25D7B , rev. 0xA5 EMMC ROM 1 (Main User Data) Capacity: 15028 MB (0003AB400000) EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000) EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000) Counter: 34316 , Response: Not Clean Extended CSD Information : Extended CSD rev: 1.8 (MMC 5.1) Boot configuration [179] / Boot Bus Config [177] / H/W Reset Function [162]: 0x38 / 0x00 / 0x01 Supported partition features [PARTITIONING_SUPPORT]: 0x07 Backup saved: HAG4a2_C1E25D7B_20200806_090427.extcsd EMMC Init completed. Scanning soft partitions GPT header is found and is valid Partition: oppodycnvbk, [000000005000 - 000000A05000], size: 000000A00000 (10.0 MB) Partition: oppostanvbk, [000000A05000 - 000001405000], size: 000000A00000 (10.0 MB) Partition: modemst1, [000001405000 - 000001585000], size: 000000180000 (1.50 MB) Partition: modemst2, [000001585000 - 000001705000], size: 000000180000 (1.50 MB) Partition: persist, [000001705000 - 000003705000], size: 000002000000 (32.0 MB) Partition: opporeserve1, [000003705000 - 000003F05000], size: 000000800000 (8.00 MB) Partition: opporeserve2, [000003F05000 - 000007F05000], size: 000004000000 (64.0 MB) Partition: reserve_exp1, [000007F05000 - 000008105000], size: 000000200000 (2.00 MB) Partition: reserve_exp2, [000008105000 - 000008305000], size: 000000200000 (2.00 MB) Partition: fsc, [000008305000 - 000008305400], size: 000000000400 (1.00 KB) Partition: ssd, [000008306000 - 000008308000], size: 000000002000 (8.00 KB) Partition: sbl1, [000008308000 - 000008388000], size: 000000080000 (512. KB) Partition: rpm, [000008388000 - 000008408000], size: 000000080000 (512. KB) Partition: tz, [000008408000 - 000008608000], size: 000000200000 (2.00 MB) Partition: devcfg, [000008608000 - 000008648000], size: 000000040000 (256. KB) Partition: sbl1bak, [000008648000 - 0000086C8000], size: 000000080000 (512. KB) Partition: rpmbak, [0000086C8000 - 000008748000], size: 000000080000 (512. KB) Partition: tzbak, [000008748000 - 000008948000], size: 000000200000 (2.00 MB) Partition: devcfgbak, [000008948000 - 000008988000], size: 000000040000 (256. KB) Partition: dsp, [000008988000 - 000009988000], size: 000001000000 (16.0 MB) Partition: DDR, [00000A000000 - 00000A008000], size: 000000008000 (32.0 KB) Partition: fsg, [00000A008000 - 00000A188000], size: 000000180000 (1.50 MB) Partition: sec, [00000A188000 - 00000A18C000], size: 000000004000 (16.0 KB) Partition: aboot, [00000A18C000 - 00000A28C000], size: 000000100000 (1.00 MB) Partition: abootbak, [00000A28C000 - 00000A38C000], size: 000000100000 (1.00 MB) Partition: modem, [00000A38C000 - 00001238C000], size: 000008000000 (128. MB) Partition: dtbo, [00001238C000 - 000012B8C000], size: 000000800000 (8.00 MB) Partition: vbmeta, [000012B8C000 - 000012B9C000], size: 000000010000 (64.0 KB) Partition: boot, [000012B9C000 - 000016B9C000], size: 000004000000 (64.0 MB) Partition: recovery, [000016B9C000 - 00001AB9C000], size: 000004000000 (64.0 MB) Partition: devinfo, [00001AB9C000 - 00001AC9C000], size: 000000100000 (1.00 MB) Partition: splash, [00001B000000 - 00001BB00000], size: 000000B00000 (11.0 MB) Partition: LOGO, [00001BB00000 - 00001DB00000], size: 000002000000 (32.0 MB) Partition: DRIVER, [00001DB00000 - 00001FB00000], size: 000002000000 (32.0 MB) Partition: cache, [00001FB00000 - 00002FB00000], size: 000010000000 (256. MB) Partition: misc, [00002FB00000 - 00002FC00000], size: 000000100000 (1.00 MB) Partition: keystore, [00002FC00000 - 00002FC80000], size: 000000080000 (512. KB) Partition: config, [00002FC80000 - 00002FC88000], size: 000000008000 (32.0 KB) Partition: oem, [00002FC88000 - 00002FD88000], size: 000000100000 (1.00 MB) Partition: limits, [000030000000 - 000030008000], size: 000000008000 (32.0 KB) Partition: mota, [000030800000 - 000030880000], size: 000000080000 (512. KB) Partition: dip, [000030880000 - 000030980000], size: 000000100000 (1.00 MB) Partition: mdtp, [000030980000 - 000032980000], size: 000002000000 (32.0 MB) Partition: syscfg, [000032980000 - 000032A00000], size: 000000080000 (512. KB) Partition: mcfg, [000032A00000 - 000032E00000], size: 000000400000 (4.00 MB) Partition: lksecapp, [000033000000 - 000033020000], size: 000000020000 (128. KB) Partition: cmnlib, [000033020000 - 000033120000], size: 000000100000 (1.00 MB) Partition: cmnlib64, [000033120000 - 000033220000], size: 000000100000 (1.00 MB) Partition: keymaster, [000033220000 - 000033320000], size: 000000100000 (1.00 MB) Partition: lksecappbak, [000033320000 - 000033340000], size: 000000020000 (128. KB) Partition: cmnlibbak, [000033340000 - 000033440000], size: 000000100000 (1.00 MB) Partition: cmnlib64bak, [000033440000 - 000033540000], size: 000000100000 (1.00 MB) Partition: keymasterbak, [000033540000 - 000033640000], size: 000000100000 (1.00 MB) Partition: apdp, [000033800000 - 000033840000], size: 000000040000 (256. KB) Partition: msadp, [000033840000 - 000033880000], size: 000000040000 (256. KB) Partition: dpo, [000033880000 - 000033882000], size: 000000002000 (8.00 KB) Partition: logdump, [000033882000 - 000037882000], size: 000004000000 (64.0 MB) Partition: vm-kystore, [000037882000 - 000037982000], size: 000000100000 (1.00 MB) Partition: vm-data, [000037982000 - 000038382000], size: 000000A00000 (10.0 MB) Partition: hyp, [000038800000 - 000039000000], size: 000000800000 (8.00 MB) Partition: vm-system, [000039000000 - 00003D000000], size: 000004000000 (64.0 MB) Partition: vm-linux, [00003D000000 - 00003F000000], size: 000002000000 (32.0 MB) Partition: system, [00003F000000 - 000115900000], size: 0000D6900000 (3.35 GB) Partition: vendor, [000115900000 - 000157860000], size: 000041F60000 (1.03 GB) Partition: userdata, [000158000000 - 0003AB3FBE00], size: 0002533FBE00 (9.30 GB) GPT header successfully parsed

08-06-2020, 08:16	#37 (permalink)
jamohaki No Life Poster Join Date: Sep 2004 Age: 51 Posts: 2,066 Member: 83397 Status: Offline Thanks Meter: 193	ok read info from easyjtag classic: Z3X EasyJtag Software ver. 3.7.0.11 Loading eMMC GEN1 Firmware... IO: 1800 mV Box S/N: , ,FW Ver.: 01.63 CMD Pullup Level:1815 mV CMD Active Level:2052 mV Box IO Level:1800 mV CLK Rate:21000 kHz Bus Width:1bit,SDR HiPower mode is ON! ---------- eMMC Device Information ---------- eMMC CID : 90014A484147346132A5C1E25D7BC5D2 eMMC CSD : D02701328F5903FFFFFFFFE78A400016 eMMC Manufacturer ID: 0090 , OEM ID: 014A eMMC Date: 12/2018 Rev.0xA5 eMMC NAME: HAG4a2 , S/N: 3252837755 eMMC NAME (HEX): 484147346132 EMMC ROM1 (Main User Data) Capacity: 15028 MB EMMC ROM2 (Boot Partition 1) Capacity: 4096 kB EMMC ROM3 (Boot Partition 2) Capacity: 4096 kB EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 kB EMMC RPMB is programmed and written 34316 times EMMC Permanent Write Protection: No EMMC Temporary Write Protection: No EMMC Password Locked: No Extended CSD rev 1.8 (MMC 5.1) Boot configuration [PARTITION_CONFIG: 0x38] Boot from:ROM1 (Main User Area) Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x38. H/W reset function [RST_N_FUNCTION]: 0x01 High-capacity WP group size [HC_WP_GRP_SIZE: 0x00002000] Partitioning Support [PARTITIONING_SUPPORT]: 0x07 Device support partitioning feature Device can have enhanced tech. Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00 --------------------------------------------- Backup saved: HAG4a2_3252837755_20200806_1011.extcsd Warning! Main and backup partition tables differ! Warning! One or more CRCs don't match. You should repair the disk! Caution: Found protective or hybrid MBR and corrupt GPT. Real (Hardware) Disk/Image size: 1D5A000 sectors 14.7 GiB Soft (Partitioned) Disk/Image size: 1D59FDA sectors 14.7 GiB Disk identifier (GUID): 98101B32-BBE2-4BF2-A06E-2BB33D000C20 Logical sector size: 0x200 bytes ,First/Last usable sector: 19,30777325 Partition info successfully found ------ Android information ------ Detected LINUX(Android) SYSTEM : 0x003F000000 (3.352GB) Short EXT fs info: Size: 3.298GB Block size: 4.0KB Inode size: 256 Inodes: 216432 Short Android info: Build ID: OPM1.171019.026 Release Base ID: 8.1.0 Security Path: 2019-03-05 Architecture ABI: arm64-v8a Device manufacturer: OPPO Build Description: msm8953_64-user 8.1.0 OPM1.171019.026 eng.root.20190323.213841 release-keys Backup saved: BuildProp_20200806_1011.txt --------------------------------------------- Detected USERDATA USERDATA : 0x0158000000 (9.299GB) Short EXT fs info: Size: 7.500GB Block size: 4.0KB Inode size: 256 Inodes: 491520 Short userdata info: Unable to read gesture.key , code 2 Done.

08-07-2020, 08:29	#38 (permalink)
jamohaki No Life Poster Join Date: Sep 2004 Age: 51 Posts: 2,066 Member: 83397 Status: Offline Thanks Meter: 193	problem not solved who can help please?

08-11-2020, 12:20	#39 (permalink)
jamohaki No Life Poster Join Date: Sep 2004 Age: 51 Posts: 2,066 Member: 83397 Status: Offline Thanks Meter: 193	EasyJtag Suite Classic ver.: 3.7.0.11 / wxWidgets 3.1.3-W-U started. OS ver.: Windows 7 (build 7601, Service Pack 1). Admin rights FAIL Autorun Agent ver:1.0.0.0 Crash Reporting ver:1.4.0.3 EasyJTAG SPI Plugin ver:1.1.1.13 Android ADB API ver:2.0.0.0 FTDI API ver:3.2.4.0 LibUSB API ver:1.2.6.0 Visual C++ Runtime ver:10.0.30319.1 Setting box Pinout ... Box Drivers version: 3.0.1.0, are OK Z3X Card Serial : , ver: 22 Z3X Card Activation [JTAGPLUS] : NOT ACTIVATED Z3X Card Activation [LG] : NOT ACTIVATED Z3X Card Activation [SAMS] : NOT ACTIVATED Z3X Card Activation [JTAG] : ACTIVATED For more information press F1 to open local help or visit our wiki Found 3 serial devices COM1 ACPI\PNP0501 Communications Port (COM1) COM17 USB\VID_0325&PID_0032&REV_0100&MI_00 Easy Jtag Control Port (COM17) COM26 USB\VID_05C6&PID_9008&REV_0000 Qualcomm HS-USB QDLoader 9008 (COM26) Selected pinout: EasyJTAG GEN1 ISP Pinout Change EasyJTAG Pinout OK Z3X EasyJtag Software ver. 3.7.0.11 Loading eMMC GEN1 Firmware... IO: 1850 mV Box S/N: 1616120653F9FBE6, ,FW Ver.: 01.63 CMD Pullup Level:1907 mV CMD Active Level:2062 mV Box IO Level:1850 mV CLK Rate:21000 kHz Bus Width:1bit,SDR HiPower mode is off! ---------- eMMC Device Information ---------- eMMC CID : 90014A484147346132A5C1E25D7BC5D2 eMMC CSD : D02701328F5903FFFFFFFFE78A400016 eMMC Manufacturer ID: 0090 , OEM ID: 014A eMMC Date: 12/2018 Rev.0xA5 eMMC NAME: HAG4a2 , S/N: 3252837755 eMMC NAME (HEX): 484147346132 EMMC ROM1 (Main User Data) Capacity: 15028 MB EMMC ROM2 (Boot Partition 1) Capacity: 4096 kB EMMC ROM3 (Boot Partition 2) Capacity: 4096 kB EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 kB EMMC RPMB is programmed and written 34316 times EMMC Permanent Write Protection: No EMMC Temporary Write Protection: No EMMC Password Locked: No Extended CSD rev 1.8 (MMC 5.1) Boot configuration [PARTITION_CONFIG: 0x38] Boot from:ROM1 (Main User Area) Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x38. H/W reset function [RST_N_FUNCTION]: 0x01 High-capacity WP group size [HC_WP_GRP_SIZE: 0x00002000] Partitioning Support [PARTITIONING_SUPPORT]: 0x07 Device support partitioning feature Device can have enhanced tech. Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00 --------------------------------------------- Backup saved: HAG4a2_3252837755_20200811_1413.extcsd Warning! Main and backup partition tables differ! Warning! One or more CRCs don't match. You should repair the disk! Caution: Found protective or hybrid MBR and corrupt GPT. Real (Hardware) Disk/Image size: 1D5A000 sectors 14.7 GiB Soft (Partitioned) Disk/Image size: 1D59FDA sectors 14.7 GiB Disk identifier (GUID): 98101B32-BBE2-4BF2-A06E-2BB33D000C20 Logical sector size: 0x200 bytes ,First/Last usable sector: 19,30777325 Partition info successfully found ------ Android information ------ Detected LINUX(Android) SYSTEM : 0x003F000000 (3.352GB) Short EXT fs info: Size: 3.298GB Block size: 4.0KB Inode size: 256 Inodes: 216432 Short Android info: Build ID: OPM1.171019.026 Release Base ID: 8.1.0 Security Path: 2019-03-05 Architecture ABI: arm64-v8a Device manufacturer: OPPO Build Description: msm8953_64-user 8.1.0 OPM1.171019.026 eng.root.20190323.213841 release-keys Backup saved: BuildProp_20200811_1413.txt --------------------------------------------- Detected USERDATA USERDATA : 0x0158000000 (9.299GB) Short EXT fs info: Size: 7.500GB Block size: 4.0KB Inode size: 256 Inodes: 491520 Short userdata info: Unable to read gesture.key , code 2 Done.

08-12-2020, 03:50	#40 (permalink)
nour2014 Freak Poster Join Date: Jul 2013 Posts: 198 Member: 1972033 Status: Offline Thanks Meter: 32	good work bro thanks alot

08-27-2020, 09:22	#41 (permalink)
T0T0 No Life Poster Join Date: Aug 2007 Age: 41 Posts: 1,031 Member: 572549 Status: Offline Thanks Meter: 175	do you have fulldump for skhynix emmc

08-28-2020, 03:14	#43 (permalink)
T0T0 No Life Poster Join Date: Aug 2007 Age: 41 Posts: 1,031 Member: 572549 Status: Offline Thanks Meter: 175	ok sir thanks i have 3 pcs a3s all skhynix emmc

09-04-2020, 11:18	#44 (permalink)
tapas770 No Life Poster Join Date: Apr 2014 Location: B A N G L A D E S H Posts: 1,333 Member: 2171294 Status: Offline Sonork: 100.1659207(No More Use) Thanks Meter: 701	very useful thread, Thanks for share

09-04-2020, 17:28	#45 (permalink)
cestin Junior Member Join Date: May 2020 Location: INDIA Posts: 15 Member: 2957188 Status: Offline Thanks Meter: 0	really it helps bro thanks for your hardwork