oppo A3S not detected

[layder]

remove phone from client and retunt to he brick - good idea

)))

remove resistor and make jumper.....
remove USB block charger from AC power and make jumper .....

Do you understand what you doing?

[reaz.com]

connect gnd line direct to mother board, not any screw hole................

[ahwak]

Z3X EasyJtag Software ver. 3.6.1.9
Loading eMMC GEN1 Firmware... IO: 3300 mV
Box S/N: 0D01300C9DDE17D1, ,FW Ver.: 01.63
CMD Pullup Level:2093 mV
CMD Active Level:2557 mV
Box IO Level:3300 mV
CLK Rate:21000 kHz
Bus Width:1bit,SDR
HiPower mode is off!
---------- eMMC Device Information ----------

eMMC CID : 90014A68423861503E03169A992975FE
eMMC CSD : D02700328F5903FFFFFFFFEF8E400042
eMMC Manufacturer ID: 0090 , OEM ID: 014A
eMMC Date: 07/2018 Rev.0x3
eMMC NAME: hB8aP> , S/N: 379230505
eMMC NAME (HEX): 68423861503E
EMMC ROM1 (Main User Data) Capacity: 29820 MB
EMMC ROM2 (Boot Partition 1) Capacity: 4096 kB
EMMC ROM3 (Boot Partition 2) Capacity: 4096 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 16384 kB
RPMB Info mmc_switch_part Error, Reason: CARD Ready Timeout Error
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
EMMC Password Locked: No
Extended CSD rev 1.8 (MMC 5.1)
Boot configuration [PARTITION_CONFIG: 0x38] Boot from:ROM1 (Main User Area)
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x38.
H/W reset function [RST_N_FUNCTION]: 0x01
High-capacity WP group size [HC_WP_GRP_SIZE: 0x00004000]
Partitioning Support [PARTITIONING_SUPPORT]: 0x07
Device support partitioning feature
Device can have enhanced tech.
Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00
---------------------------------------------
Backup saved: hB8aP>_ 379230505_20190703_2351.extcsd
Found valid GPT with protective MBR; using GPT.
Real (Hardware) Disk/Image size: 3A3E000 sectors 29.1 GiB
Soft (Partitioned) Disk/Image size: 3A3DFBC sectors 29.1 GiB
Disk identifier (GUID): 98101B32-BBE2-4BF2-A06E-2BB33D000C20
Logical sector size: 0x200 bytes ,First/Last usable sector: 34,61071326
Partition info successfully found
------ Android information ------
Detected LINUX(Android) SYSTEM : 0x003F000000 (3.352GB)
Build ID: OPM1.171019.026
Release Base ID: 8.1.0
Architecture ABI: arm64-v8a
Device manufacturer: OPPO
Build Description: msm8953_64-user 8.1.0 OPM1.171019.026 eng.root.20190323.213841 release-keys
---------------------------------------------
Detected USERDATA USERDATA : 0x0158000000 (23.745GB)
Unable to mount USERDATA , code : 95
Done.




what is that error



RPMB Info mmc_switch_part Error, Reason: CARD Ready Timeout Error

[gayansuranga]

disconnect the jtag connections and turn on the phone wait till it starts then turn it off and start over again the jtag process . I it must be user data partitions not initialized properly due to abnormal shut downs.

[imanka]

oppo a3s not conect


MMC_tool Suite ver. 1.6.2.0 (release date: 30.06.2019)
7/5/2019 12:56:52 PM> Microsoft Windows 7 (32 bit) build 7601 (6.1.7600.16385)
7/5/2019 12:56:52 PM>
7/5/2019 12:56:52 PM> Looking for EasyJTAG box...
7/5/2019 12:56:52 PM> EasyJTAG API ver. 3307
7/5/2019 12:56:55 PM> OpenUSB returned = 0
7/5/2019 12:56:56 PM> EasyJTAG Box Serial = 07FFA00BB62EEC02
7/5/2019 12:56:57 PM> Card Serial = AA3D83FD
7/5/2019 12:56:57 PM> EasyJTAG Box Firmware = 1.63
7/5/2019 12:56:57 PM>
7/5/2019 12:57:15 PM> Looking for EasyJTAG box...
7/5/2019 12:57:15 PM> EasyJTAG API ver. 3307
7/5/2019 12:57:15 PM> Setting IO Levels to 1.8V
7/5/2019 12:57:15 PM> Setting frequence to 21 MHz
7/5/2019 12:57:16 PM> EasyJTAG Box Serial = 07FFA00BB62EEC02
7/5/2019 12:57:16 PM> EasyJTAG Box Firmware = 1.63
7/5/2019 12:57:19 PM> HiPower mode is ON
7/5/2019 12:57:19 PM> Setting frequence to 21 MHz
7/5/2019 12:57:19 PM> CMD Pullup Level: 247 mV
7/5/2019 12:57:19 PM> CMD Active Level: 2000 mV
7/5/2019 12:57:19 PM> eMMC Init returned = -1
7/5/2019 12:57:19 PM> Can't init device. Reason: CMD Timeout Error
7/5/2019 12:57:19 PM>

[imanka]

now clk resister missing by my mistake now stuck on quellcomm port only phone not power on

is compatible MOORCK emmc adapter for emmc repair ? I have not good skill to emmc repair
but I am trying to with easy jtag experts so please help me as a newcomer

[ChandruChiyyan]

Just make short clk lines your phone should on After clk lines short

[rico_deep]

do we need to remove CLK resistor to connect via direct emmc?

i have 2 unit A3s 1803 model

16gb samsung emmc done via oppo reset but the unit with 32gb hynix emmc cannot connect, always say "Can't init device, Reason: CARD Ready Timeout Error "..

[ChandruChiyyan]

Originally Posted by rico_deep

do we need to remove CLK resistor to connect via direct emmc?

i have 2 unit A3s 1803 model

16gb samsung emmc done via oppo reset but the unit with 32gb hynix emmc cannot connect, always say "cmd error: Card not ready"..

No need to remove clk resistor for direct connect Emmc...Maybe your connection not well in cmd line please check ..

[rico_deep]

same problem here, A3s (1803) 32Gb Hynix eMMC

always "Can't init device, Reason: CARD Ready Timeout Error"

[gaguk arif]

coba pakai adapter ufi

[rico_deep]

Originally Posted by gaguk arif

coba pakai adapter ufi

my adaptor is working on A3s(1803) and A3s(1853) with 16gb samsung eMMC

[layder]

http://forum.gsmhosting.com/vbb/f672...-jtag-2636216/

[rico_deep]

Originally Posted by layder

http://forum.gsmhosting.com/vbb/f672...-jtag-2636216/

no problem with A3s with samsung emmc, hynix emmc how ever give us error

[imanka]

Originally Posted by ChandruChiyyan

Just make short clk lines your phone should on After clk lines short

after short clk line pone switch on yhanks to ChandruChiyyan;13723164
why cannot read Hynix eMMC by easy jtag? any solution?